[PATCH v4 6/6] ARM: dts: sun8i: q8-common: Add AXP223 PMIC device and regulator nodes

Chen-Yu Tsai wens at csie.org
Mon Nov 23 19:48:36 PST 2015


A23/A33 Q8 tablets have an X-Powers AXP223 PMIC connected via RSB. Its
regulators provide power to various parts of the SoC and the board.

Also add lcd regulator supply for simplefb and update the existing
vmmc-supply for mmc0.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
 arch/arm/boot/dts/sun8i-q8-common.dtsi | 86 +++++++++++++++++++++++++++++++++-
 1 file changed, 84 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/sun8i-q8-common.dtsi
index 1a69231d2da5..01ab47b32d8d 100644
--- a/arch/arm/boot/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/boot/dts/sun8i-q8-common.dtsi
@@ -56,7 +56,6 @@
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <8>;
 		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
-		/* backlight is powered by AXP223 DC1SW */
 	};
 
 	chosen {
@@ -67,7 +66,7 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
-	vmmc-supply = <&reg_vcc3v0>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
 	cd-inverted;
@@ -92,6 +91,85 @@
 
 &r_rsb {
 	status = "okay";
+
+	axp22x: pmic at 3e3 {
+		compatible = "x-powers,axp223";
+		reg = <0x3e3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+	};
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <2350000>;
+	regulator-max-microvolt = <2650000>;
+	regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_rtc_ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-rtc";
 };
 
 &r_uart {
@@ -99,3 +177,7 @@
 	pinctrl-0 = <&r_uart_pins_a>;
 	status = "okay";
 };
+
+&simplefb_lcd {
+	vcc-lcd-supply = <&reg_dc1sw>;
+};
-- 
2.6.2




More information about the linux-arm-kernel mailing list