[PATCH] PCI: Fix pcibios_update_irq misuse of irq number

Marc Zyngier marc.zyngier at arm.com
Mon Feb 2 08:15:23 PST 2015


On 28/01/15 15:43, Bjorn Helgaas wrote:
> On Wed, Jan 28, 2015 at 9:27 AM, Marc Zyngier <marc.zyngier at arm.com> wrote:
>> Hi Gerry,
>>
>> On 28/01/15 15:21, Jiang Liu wrote:
>>>
>>>
>>> On 2015/1/28 22:51, Marc Zyngier wrote:
>>>> pcibios_update_irq writes an irq number into the config space
>>>> of a given PCI device, but ignores the fact that this number
>>>> is a virtual interrupt number, which might be a very different
>>>> value from what the underlying hardware is using.
>>>>
>>>> The obvious fix is to fetch the HW interrupt number from the
>>>> corresponding irq_data structure. This is slightly complicated
>>>> by the fact that this interrupt might be services by a stacked
>>>> domain.
>>>>
>>>> This has been tested on KVM with kvmtool.
>>>>
>>>> Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
>>>> Tested-by: Andre Przywara <andre.przywara at arm.com>
>>>> Signed-off-by: Marc Zyngier <marc.zyngier at arm.com>
>>>> ---
>>>>  drivers/pci/setup-irq.c | 12 ++++++++++--
>>>>  1 file changed, 10 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/pci/setup-irq.c b/drivers/pci/setup-irq.c
>>>> index 4e2d595..828cbc9 100644
>>>> --- a/drivers/pci/setup-irq.c
>>>> +++ b/drivers/pci/setup-irq.c
>>>> @@ -15,11 +15,19 @@
>>>>  #include <linux/errno.h>
>>>>  #include <linux/ioport.h>
>>>>  #include <linux/cache.h>
>>>> +#include <linux/irq.h>
>>>>
>>>>  void __weak pcibios_update_irq(struct pci_dev *dev, int irq)
>>>>  {
>>>> -    dev_dbg(&dev->dev, "assigning IRQ %02d\n", irq);
>>>> -    pci_write_config_byte(dev, PCI_INTERRUPT_LINE, irq);
>>>> +    struct irq_data *d;
>>>> +
>>>> +    d = irq_get_irq_data(irq);
>>>> +#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY
>>>> +    while (d->parent_data)
>>>> +            d = d->parent_data;
>>>> +#endif
>>>> +    dev_dbg(&dev->dev, "assigning IRQ %02ld\n", d->hwirq);
>>>> +    pci_write_config_byte(dev, PCI_INTERRUPT_LINE, d->hwirq);
>>>>  }
>>> Hi Mark,
>>>       Instead of modifying the common version, how about
>>> implementing an arch specific version? Arch may have different
>>> way to determine the irq number. Above implementation doesn't
>>> work with x86, for example.
>>
>> If you look at the Makefile, this file is used on:
>>
>> obj-$(CONFIG_ALPHA) += setup-irq.o
>> obj-$(CONFIG_ARM) += setup-irq.o
>> obj-$(CONFIG_UNICORE32) += setup-irq.o
>> obj-$(CONFIG_SUPERH) += setup-irq.o
>> obj-$(CONFIG_MIPS) += setup-irq.o
>> obj-$(CONFIG_TILE) += setup-irq.o
>> obj-$(CONFIG_SPARC_LEON) += setup-irq.o
>> obj-$(CONFIG_M68K) += setup-irq.o
>>
>> x86 doesn't use that at all.
> 
> Since you're looking at this, Marc, do you see a nice way to get rid
> of these arch dependencies in the Makefile and unify this a bit?  We
> still have this pci_fixup_irqs() ugliness -- it's not really
> arch-specific at all, but it's called from arch code, and it uses
> for_each_pci_dev(), which obviously only works for things present at
> boot and not for things hot-added later.

I can have a look at this in the next cycle - I'm a bit strapped for
time just now.

As for for_each_pci_dev(), I'm not completely clear about what it should
be replaced for. Do we have some form of notifier for this?

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...



More information about the linux-arm-kernel mailing list