[PATCH v4 4/7] ARM: dts: imx: Add support for Advantech/GE Bx50v3

Akshay Bhat akshay.bhat at timesys.com
Wed Dec 2 10:16:17 PST 2015


From: Justin Waters <justin.waters at timesys.com>

Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.

Signed-off-by: Akshay Bhat <akshay.bhat at timesys.com>
---
 arch/arm/boot/dts/imx6q-bx50v3.dtsi | 207 ++++++++++++++++++++++++++++++++++++
 1 file changed, 207 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-bx50v3.dtsi

diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
new file mode 100644
index 0000000..61bb9aa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
@@ -0,0 +1,207 @@
+/*
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "imx6q-ba16.dtsi"
+
+/ {
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mclk: clock at 0 {
+			compatible = "fixed-clock";
+			reg = <0>;
+			#clock-cells = <0>;
+			clock-frequency = <22000000>;
+		};
+	};
+
+	reg_wl18xx_vmmc: regulator at 6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1807";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pca9539 3 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	reg_wlan: regulator at 7 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V_wlan";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	sound {
+		compatible = "fsl,imx6q-ba16-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-ba16-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
+};
+
+&ecspi5 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi5>;
+	status = "okay";
+
+	m25_eeprom: m25p80 at 0 {
+		compatible = "atmel,at25";
+		spi-max-frequency = <20000000>;
+		size = <0x8000>;
+		pagesize = <64>;
+		reg = <0>;
+		address-width = <16>;
+	};
+};
+
+&i2c1 {
+	pca9547: mux at 70 {
+		compatible = "nxp,pca9547";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mux_i2c3: i2c at 0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			ads7830: ads7830 at 48 {
+				compatible = "ti,ads7830";
+				reg = <0x48>;
+			};
+
+			mma8453: mma8453 at 1c {
+				compatible = "fsl,mma8453";
+				reg = <0x1c>;
+			};
+		};
+
+		mux_i2c4: i2c at 1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			eeprom: eeprom at 50 {
+				compatible = "atmel,24c08";
+				reg = <0x50>;
+			};
+
+			mpl3115: mpl3115 at 60 {
+				compatible = "fsl,mpl3115";
+				reg = <0x60>;
+			};
+		};
+
+		mux_i2c5: i2c at 2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+
+		mux_i2c6: i2c at 3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			codec: sgtl5000 at 0a {
+				compatible = "fsl,sgtl5000";
+				reg = <0x0a>;
+				clocks = <&mclk>;
+				VDDA-supply = <&reg_1p8v>;
+				VDDIO-supply = <&reg_3p3v>;
+			};
+		};
+
+		mux_i2c7: i2c at 4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			pca9539: pca9539 at 74 {
+				compatible = "nxp,pca9539";
+				reg = <0x74>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				interrupt-parent = <&gpio2>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			};
+		};
+
+		mux_i2c8: i2c at 5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+
+			igb at 49 {
+				compatible = "intel,igb";
+				reg = <0x49>;
+			};
+
+			igb at 61 {
+				compatible = "intel,igb";
+				reg = <0x61>;
+			};
+		};
+
+		mux_i2c9: i2c at 6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+
+		mux_i2c10: i2c at 7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_wl18xx_vmmc>;
+	no-1-8-v;
+	non-removable;
+	enable-sdio-wakeup;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	max-frequency = <25000000>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore at 0 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+		tcxo-clock-frequency = <26000000>;
+	};
+};
-- 
2.6.3




More information about the linux-arm-kernel mailing list