[PATCH 2/4] mtd: mxc_nand: limit the size of used oob

Baruch Siach baruch at tkos.co.il
Sun Apr 26 21:39:06 PDT 2015


Hi Uwe,

On Sun, Apr 26, 2015 at 10:07:25PM +0200, Uwe Kleine-König wrote:
> On Sun, Apr 26, 2015 at 11:16:49AM +0300, Baruch Siach wrote:
> > For 4k pages the i.MX NFC hardware uses exactly 218 or 128 bytes for 4bit or
> > 8bit ECC data, respectively. Larger oobsize confuses the logic of copy_spare().
> > Limit the size of used oob size to avoid that.
> > 
> > Signed-off-by: Baruch Siach <baruch at tkos.co.il>
> > ---
> >  drivers/mtd/nand/mxc_nand.c | 15 +++++++++++----
> >  1 file changed, 11 insertions(+), 4 deletions(-)
> > 
> > diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
> > index 33b22b9c0b30..c650f0950b20 100644
> > --- a/drivers/mtd/nand/mxc_nand.c
> > +++ b/drivers/mtd/nand/mxc_nand.c
> > @@ -819,15 +819,22 @@ static void copy_spare(struct mtd_info *mtd, bool bfrom)
> >  {
> >  	struct nand_chip *this = mtd->priv;
> >  	struct mxc_nand_host *host = this->priv;
> > -	u16 i, oob_chunk_size;
> > +	u16 i, oob_chunk_size, used_oobsize;
> >  	u16 num_chunks = mtd->writesize / 512;
> >  
> >  	u8 *d = host->data_buf + mtd->writesize;
> >  	u8 __iomem *s = host->spare0;
> >  	u16 sparebuf_size = host->devtype_data->spare_len;
> >  
> > +	/* hardware can only use 218 or 128 oob bytes for ecc */
> > +	if (mtd->oobsize >= 218)
> IMHO this is the wrong check. What if your part (with 224 bytes spare)
> is used but the machine only uses the small layout e.g. for booting?
> (That would work, wouldn't it?)

Yes, but how would I know? I am following here the assumption of get_eccsize() 
that enables 8 bit ECC when there is enough oobsize.

> Moreover the comment is misleading as it
> only applies to 4K flashes. At least the driver works well with (2ki +
> 128) bytes pages (while there are only 64 bytes spare used?? Maybe there
> are still more bugs?).

I suspect there are more bugs. A simple way to trigger the bug I encountered 
is by doing a sub-page write, that is:

  dd if=/dev/zero bs=1024 count=1 of=/dev/mtd2
  dd if=/dev/zero bs=1024 count=1 seek=1 of=/dev/mtd2

and then try reading this page. You may need to dirty the (useless; random) 
content of ecccalc to see the bug (you can conveniently use 
mxc_nand_calculate_ecc() for that). What copy_spare() currently do (spread ECC 
chunks evenly over oob) does not match nandv2_hw_eccoob_largepage.

> > +		used_oobsize = 218;
> > +	else if (mtd->oobsize >= 128)
> > +		used_oobsize = 128;
> > +	else
> > +		used_oobsize = mtd->oobsize;
> Is it worth to put this check into _probe and put the used size into
> driver data?

I think you are right. I'll also add checks for smaller page/oob size.

Thanks for reviewing,
baruch

-- 
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.2.679.5364, http://www.tkos.co.il -



More information about the linux-arm-kernel mailing list