[PATCH v2] ARM: tegra: Correct which USB controller has the UTMI pad registers

[Tomeu Vizoso]

It should be the first controller, not the second.

This broke USB after 6261b06 ("regulator: Defer lookup of supply to
regulator_get"), because it changed the order in which the controllers
were probed.

The fix for this issue was suggested by Mikko Perttunen.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso at collabora.com>
Cc: Mikko Perttunen <mikko.perttunen at kapsi.fi>
---

I think that the line numbers should be enough in this case, as I expect this to be merged soon, but just in case I'm sending the same patch with plenty of context.

Regards,

Tomeu

---
 arch/arm/boot/dts/tegra124.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi
index cf01c81..cb786a9 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/tegra124.dtsi
@@ -821,77 +821,77 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d000000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USBD>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
 			 <&tegra_car TEGRA124_CLK_USBD>;
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
 		nvidia,term-range-adj = <6>;
 		nvidia,xcvr-setup = <9>;
 		nvidia,xcvr-lsfslew = <0>;
 		nvidia,xcvr-lsrslew = <3>;
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,has-utmi-pad-registers;
 		status = "disabled";
 	};
 
 	usb at 0,7d004000 {
 		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
 		reg = <0x0 0x7d004000 0x0 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB2>;
 		resets = <&tegra_car 58>;
 		reset-names = "usb";
 		nvidia,phy = <&phy2>;
 		status = "disabled";
 	};
 
 	phy2: usb-phy at 0,7d004000 {
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d004000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB2>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
 			 <&tegra_car TEGRA124_CLK_USBD>;
 		clock-names = "reg", "pll_u", "utmi-pads";
 		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
 		nvidia,elastic-limit = <16>;
 		nvidia,term-range-adj = <6>;
 		nvidia,xcvr-setup = <9>;
 		nvidia,xcvr-lsfslew = <0>;
 		nvidia,xcvr-lsrslew = <3>;
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
-		nvidia,has-utmi-pad-registers;
 		status = "disabled";
 	};
 
 	usb at 0,7d008000 {
 		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
 		reg = <0x0 0x7d008000 0x0 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB3>;
 		resets = <&tegra_car 59>;
 		reset-names = "usb";
 		nvidia,phy = <&phy3>;
 		status = "disabled";
 	};
 
 	phy3: usb-phy at 0,7d008000 {
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d008000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
 		phy_type = "utmi";
-- 
2.3.4