[GIT PULL] Renesas ARM Based SoC Koelsch Board Removal Updates for v3.19

[Simon Horman]

On Thu, Nov 20, 2014 at 08:33:48AM +0100, Arnd Bergmann wrote:
> On Thursday 20 November 2014 09:40:03 Simon Horman wrote:
> > On Wed, Nov 19, 2014 at 11:06:43PM +0100, Arnd Bergmann wrote:
> > > On Tuesday 04 November 2014, Simon Horman wrote:
> 
> > > > ----------------------------------------------------------------
> > > > Renesas ARM Based SoC Koelsch Board Removal Updates for v3.19
> > > > 
> > > > * Remove lecacy C koelsh board support
> > > 
> > > I've tried merging this one in two ways, but I'm not too happy about either one:
> > > 
> > > - we could put it into next/boards, but I don't think there will be anything
> > >   else in that branch and I was considering not to have one at all.
> > > 
> > > - it would also fit into next/cleanup, but then we already have
> > >   renesas-dt-cleanups-for-v3.19 categorized as "next/dt" rather than
> > >   "next/cleanup". Moving that one into cleanups solves the problem
> > >   nicely, but it's rather large and my feeling is that Olof's decision
> > >   to put it into next/dt was better.
> > 
> > My assumption was that it is reasonable to base something on a cleanup
> > and that as the other base for this is next/dt the this pull request
> > would also end up in next/dt.
> 
> Correct in principle. Sometimes however we decide to put things into
> a different branch than what you had planned, and this is what happened
> here when Olof put the dt-cleanup into next/dt, which we normally do
> for pull requests that only touch the dts files.

Thanks for the clarification.

> > > I think you are trying too hard to avoid merge conflicts, as I can't see any
> > > true dependency on renesas-dt-cleanups-for-v3.19, and I'd be happier if
> > > you could rebase it onto renesas-dt-du-for-v3.19 by itself. There is
> > > a trivial merge conflict that I have to resolve, but it seems more
> > > sensible that way.
> > > 
> > > Any other thoughts?
> > 
> > Unfortunately its not quite so simple. The patch
> > 
> > "ARM: shmobile: koelsch dts: Drop console= bootargs parameter"
> > in renesas-koelsch-board-removal-for-v3.19 depends on 
> > "ARM: shmobile: kzm9g-reference dts: Add chosen/stdout-path"
> > which is on renesas-dt-cleanups-for-v3.19.
> > 
> > Perhaps it would be better if the latter had not been classified as a
> > cleanup. On that topic I must say that I find splitting out
> > some patches as cleanups to not be a very useful classification for me.
> > 
> > A possibility would be to duplicate "ARM: shmobile: kzm9g-reference dts:
> > Add chosen/stdout-path" in a revised renesas-koelsch-board-removal-for-v3.19.
> > I believe that would leave us with only a trivial conflict in
> > arch/arm/boot/dts/Makefile.
> 
> Thanks for the explanation. I think the best way forward is to just
> classify both renesas-dt-cleanups-for-v3.19 and renesas-koelsch-board-removal-for-v3.19
> as cleanups then, which I've done. The dt-cleanup is now in both
> next/cleanup and next/dt, while dt-cleanup2 and dt-cleanup3 remain
> just in next/dt.

Thanks, I appreciate it.
Its nice to get these changes into (and some legacy code out of) v3.19.