[PATCH 1/3] Documentation: add Device tree bindings for Hisilicon hip04 ethernet

[Zhangfei Gao]

This patch adds the Device Tree bindings for the Hisilicon hip04
Ethernet controller, including 100M / 1000M controller.

Signed-off-by: Zhangfei Gao <zhangfei.gao at linaro.org>
---
 .../bindings/net/hisilicon-hip04-net.txt           |  107 ++++++++++++++++++++
 1 file changed, 107 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt

diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
new file mode 100644
index 0000000..22838b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt
@@ -0,0 +1,107 @@
+Hisilicon hip04 Ethernet Controller
+
+* Ethernet controller node
+
+Required properties:
+- compatible: should be "hisilicon,hip04-mac".
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device.
+- port-handle: phandle, specifies a reference to a node representing
+  the connected port
+- Inherets from ethernet common binding [1]
+[1] Documentation/devicetree/bindings/net/ethernet.txt
+
+
+* Ethernet ppe node:
+Control rx & tx fifos of all ethernet controllers.
+Have 2048 recv channels shared by all ethernet controllers, only if no overlap.
+Each controller's start recv channel is alisa_id * RX_DESC_NUM.
+
+Required properties:
+- #address-cells : Should be <1>
+- #size-cells : Should be <0>
+- compatible: "hisilicon,hip04-ppe"
+- reg: address and length of the register set for the device.
+
+==Child node==
+
+Required properties:
+- reg: port physical number, range from 0 to 0x1f
+
+
+* MDIO bus node:
+
+Required properties:
+
+- compatible: should be "hisilicon,hip04-mdio", "ethernet-phy-ieee802.3-c22".
+- Inherets from MDIO bus node binding [2]
+[2] Documentation/devicetree/bindings/net/phy.txt
+
+Example:
+	aliases {
+		ethernet0 = &fe;
+		ethernet1 = &ge0;
+		ethernet2 = &ge8;
+	};
+
+	mdio {
+		compatible = "hisilicon,hip04-mdio", "ethernet-phy-ieee802.3-c22";
+		reg = <0x28f1000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+
+		phy1: ethernet-phy at 1 {
+			reg = <1>;
+			marvell,reg-init = <18 0x14 0 0x8001>;
+		};
+	};
+
+	ppe: ppe at 28c0000 {
+		compatible = "hisilicon,hip04-ppe";
+		reg = <0x28c0000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth0_port: port at 1f {
+			reg = <0x1f>;
+		};
+
+		eth1_port: port at 0 {
+			reg = <0>;
+		};
+
+		eth2_port: port at 8 {
+			reg = <8>;
+		};
+	};
+
+	fe: ethernet at 28b0000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x28b0000 0x10000>;
+		interrupts = <0 413 4>;
+		phy-mode = "mii";
+		port-handle = <&eth0_port>;
+	};
+
+	ge0: ethernet at 2800000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2800000 0x10000>;
+		interrupts = <0 402 4>;
+		phy-mode = "sgmii";
+		port-handle = <&eth1_port>;
+		phy-handle = <&phy0>;
+	};
+
+	ge8: ethernet at 2880000 {
+		compatible = "hisilicon,hip04-mac";
+		reg = <0x2880000 0x10000>;
+		interrupts = <0 410 4>;
+		phy-mode = "sgmii";
+		port-handle = <&eth2_port>;
+		phy-handle = <&phy1>;
+	};
-- 
1.7.9.5