[PATCH v2 1/2] ARM: dts: Add omap specific pinctrl defines to use padconf addresses

[Tony Lindgren]

* Laurent Pinchart <laurent.pinchart at ideasonboard.com> [140107 15:26]:
> Hi Tony,
> 
> On Tuesday 07 January 2014 15:20:18 Tony Lindgren wrote:
> > * Laurent Pinchart <laurent.pinchart at ideasonboard.com> [140107 15:10]:
> > > On Tuesday 07 January 2014 14:30:21 Tony Lindgren wrote:
> > > > * Laurent Pinchart <laurent.pinchart at ideasonboard.com> [131220 07:52]:
> > > > > From: Tony Lindgren <tony at atomide.com>
> > > > > +/*
> > > > > + * Macros to allow using the absolute physical address instead of the
> > > > > + * padconf registers instead of the offset from padconf base.
> > > > > + */
> > > > > +#define OMAP_IOPAD_OFFSET(pa, offset)	(((pa) & 0xffff) - (offset))
> > > > > +
> > > > > +#define OMAP2420_CORE_IOPAD(pa, val)	OMAP_IOPAD_OFFSET((pa), 0x0030)
> > > > > (val)
> > > > > +#define OMAP2430_CORE_IOPAD(pa, val)	OMAP_IOPAD_OFFSET((pa), 0x2030)
> > > > > (val)
> > > > > +#define OMAP3_CORE1_IOPAD(pa, val)	OMAP_IOPAD_OFFSET((pa), 0x2030)
> > > > > (val)
> > > > > +#define OMAP3_CORE2_IOPAD(pa, val)	OMAP_IOPAD_OFFSET((pa), 0x25a0)
> > > > > (val)
> > > > 
> > > > Sorry for the delay on these, I'm only now getting back to looking
> > > > at all the emails since the holidays :)
> > > > 
> > > > After looking at Nishant's omap3 pinctrl core2 patch, looks like we need
> > > > to have separate OMAP3430_CORE2_IOPAD and OMAP3630_CORE2_IOPAD defines.
> > > 
> > > That was my first impression as well, but I think we actually don't need
> > > to. The OMAP3430 just has no useful registers in the 0x25a0 - 0x25d7
> > > area, so we can make the CORE2 macro span that for both 3430 and 3630.
> > 
> > Hmm well I already did it :)
> 
> Haven't you been taught that you should send patches for review before 
> applying them ? ;-)

Using the "trivial change to an earlier patch" clause here ;)
 
> > In general my gut feeling is along the lines what you're saying, I think the
> > padconf registers are all there on all omap3 SoCs, but only some of the
> > padconf registers are used depending on the SoC revision and package.
> > 
> > Anyways, it should not hurt to have the padconf registers defined the
> > same way as the documentation has them, at least we may get some extra
> > warnings if people try to configure unused registers for 3430.
> 
> As long as the bug is fixed in a reasonably clean way I'm fine with that. This 
> seems to count as a reasonably clean way, so no complaint :-)

Thanks :)

BTW, I'm queueing these for v3.14, hopefully everybody is fine
with that as these changes are getting pretty intrusive for v3.13.
If people really need these for v3.13, please yell.

Regards,

Tony