[PATCH V2 2/2] ARM: dts: omap3-ldp: fix mmc configuration

Nishanth Menon nm at ti.com
Fri Feb 14 00:45:49 EST 2014


MMC1 is the only MMC interface available on the platform. Further,
since the platform is based on older revision of SoC which is not
capable of doing multi-block reads, mark it with compatibility for the
same and add pinmux to ensure that all relevant pins are configured
for non-MMC boot mode.

Signed-off-by: Nishanth Menon <nm at ti.com>
---

Changes since V1:
	- fixed commit message as suggested by Balaji.
	- update to use new compatible match for the erratum.

V1: https://patchwork.kernel.org/patch/3514881/

 arch/arm/boot/dts/omap3-ldp.dts |   23 +++++++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts
index ddce0d8..0abe986 100644
--- a/arch/arm/boot/dts/omap3-ldp.dts
+++ b/arch/arm/boot/dts/omap3-ldp.dts
@@ -174,8 +174,20 @@
 };
 
 &mmc1 {
+	/* See 35xx errata 2.1.1.128 in SPRZ278F */
+	compatible = "ti,omap3-pre-es3-hsmmc";
 	vmmc-supply = <&vmmc1>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+	status="disabled";
+};
+
+&mmc3 {
+	status="disabled";
 };
 
 &omap3_pmx_core {
@@ -209,6 +221,17 @@
 			0x174 (PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
 		>;
 	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.mmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214A, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.mmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214C, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.mmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
+		>;
+	};
 };
 
 &usb_otg_hs {
-- 
1.7.9.5




More information about the linux-arm-kernel mailing list