[PATCH v2 7/7] pinctrl: qcom-spmi-gpio: Migrate to pinconf-generic

Ivan T. Ivanov iivanov at mm-sol.com
Thu Dec 4 01:30:58 PST 2014


On Wed, 2014-12-03 at 09:38 -0800, Sören Brinkmann wrote:
> On Wed, 2014-12-03 at 03:03PM +0200, Ivan T. Ivanov wrote:
> > On Thu, 2014-11-27 at 17:26 -0800, Soren Brinkmann wrote:
> > > Instead of the driver caring about implementation details like device
> > > tree, just provide information about driver specific pinconf parameters
> > > to pinconf-generic which takes care of parsing the DT.
> > > 
> > > Signed-off-by: Soren Brinkmann brinkmann at xilinx.com>
> > > ---
> > > This is compile tested only. So, it's likely that it needs more tweaking
> > > to make it actually work on HW. But it illustrates the potential
> > > benefits of the pinconf-generic changes in this series.
> > > ---
> > >  drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 125 +++----------------------------
> > >  1 file changed, 11 insertions(+), 114 deletions(-)
> > > 
> > > diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-
> > > gpio.c
> > > index b863b5080890..2db85e53ef73 100644
> > > --- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> > > +++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
> > > @@ -131,14 +131,14 @@ struct pmic_gpio_state {
> > >         struct gpio_chip chip;
> > >  };
> > > 
> > > -struct pmic_gpio_bindings {
> > > -       const char*property;
> > > -       unsigned      param;
> > > +static const struct pinconf_generic_dt_params pmic_gpio_bindings[] = {
> > > +       {"qcom,pull-up-strength",PMIC_GPIO_CONF_PULL_UP,0},
> > > +       {"qcom,drive-strength",PMIC_GPIO_CONF_STRENGTH,0},
> > >  };
> > > 
> > > -static struct pmic_gpio_bindings pmic_gpio_bindings[] = {
> > > -       {"qcom,pull-up-strength",PMIC_GPIO_CONF_PULL_UP},
> > > -       {"qcom,drive-strength",PMIC_GPIO_CONF_STRENGTH},
> > > +static const struct pin_config_item pmic_conf_items[] = {
> > > +       PCONFDUMP(PMIC_GPIO_CONF_PULL_UP,  "pull-up-strength", NULL, true),
> > 
> > s/pull-up-strength/qcom,pull-up-strength/
> 
> This is used for the debugfs output. I don't think you want the qcom
> prefix here, do you?

Then at lest lets make it "pull up strength".

> 
> > > +       PCONFDUMP(PMIC_GPIO_CONF_STRENGTH, "drive-strength", NULL, true),
> > >  };
> > > 
> > 
> > 
> > 
> > I am not happy that we have to define the same think two times.
> 
> It's not really the same thing. One is the actual DT binding the other
> how the property is displayed in debugfs. Two different things. It's how
> the core does it. That's not new.

This didn't make me more happy :-). Could both be merged?

Regards,
Ivan




More information about the linux-arm-kernel mailing list