[PATCH v4] ARM:dts:omap4-panda: Update the LED support for the panda DTS

Nishanth Menon nm at ti.com
Wed May 15 13:05:16 EDT 2013


On 11:46-20130515, Dan Murphy wrote:
> The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
> are different.
> 
> A1-A3 = gpio_wk7
> ES = gpio_110
> 
> There is no change to LED D2
> 
> Abstract away the pinmux and the LED definitions for the two boards into
> the respective DTS files.
> 
> Signed-off-by: Dan Murphy <dmurphy at ti.com>
> ---
nit: Giving patch history is a nice practise.
>  arch/arm/boot/dts/omap4-panda-common.dtsi |   16 +++++++++++-
>  arch/arm/boot/dts/omap4-panda-es.dts      |   40 +++++++++++++++++++++++++++++
>  2 files changed, 55 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
> index 03bd60d..2b516af 100644
> --- a/arch/arm/boot/dts/omap4-panda-common.dtsi
> +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
> @@ -16,7 +16,7 @@
>  		reg = <0x80000000 0x40000000>; /* 1 GB */
>  	};
>  
> -	leds {
> +	leds: leds {
>  		compatible = "gpio-leds";
>  		heartbeat {
>  			label = "pandaboard::status1";
> @@ -137,6 +137,20 @@
I missed noticing this previously, Apologies on the same.
Considering that drivers/leds/leds-gpio.c has ability to handle pinctrl,
One better option might be to provide pinctrl phandle with leds -
Couple of reasons why this might be good:
a) one gets the following warning at boot:
"leds-gpio leds.8: pins are not configured from the driver"
b) you donot need to setup the pins by default at boot - it is not
mandatory for the system functionality, instead we do it *if* the driver
is enabled.
Further, optionally, all you'd have to do in panda-es.dts is the following
&led_wkgpio_pins {
		pinctrl-single,pins = <
			0x1c 0x3	/* gpio_wk8 OUTPUT | MODE 3 */
		>;
}
Similarly for gpios override for panda-es.

>  	};
>  };
>  
> +&omap4_pmx_wkup {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +		&led_wkgpio_pins
> +	>;
> +
> +	led_wkgpio_pins: pinmux_leds_wkpins {
> +		pinctrl-single,pins = <
> +			0x1a 0x3	/* gpio_wk7 OUTPUT | MODE 3 */
> +			0x1c 0x3	/* gpio_wk8 OUTPUT | MODE 3 */
> +		>;
> +	};
> +};
> +
>  &i2c1 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&i2c1_pins>;
> diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
> index f1d8c21..e6f696d 100644
> --- a/arch/arm/boot/dts/omap4-panda-es.dts
> +++ b/arch/arm/boot/dts/omap4-panda-es.dts
> @@ -34,3 +34,43 @@
>  		0x5e 0x100	/* hdmi_sda.hdmi_sda INPUT | MODE 0 */
>  		>;
>  };
> +
> +&leds {
> +	compatible = "gpio-leds";
> +	heartbeat {
> +		label = "pandaboard::status1";
> +		gpios = <&gpio4 14 0>;
> +		linux,default-trigger = "heartbeat";
> +	};
> +	mmc {
> +		label = "pandaboard::status2";
> +		gpios = <&gpio1 8 0>;
> +		linux,default-trigger = "mmc0";
> +	};
> +};
> +
> +&omap4_pmx_core {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +		&led_gpio_pins
> +	>;
> +
> +	led_gpio_pins: gpio_led_pmx {
> +		pinctrl-single,pins = <
> +			0xb6 0x3	/* gpio_110 OUTPUT | MODE 3 */
> +		>;
> +	};
> +};
> +
> +&omap4_pmx_wkup {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +		&led_wkgpio_pins
> +	>;
> +
> +	led_wkgpio_pins: pinmux_leds_wkpins {
> +		pinctrl-single,pins = <
> +			0x1c 0x3	/* gpio_wk8 OUTPUT | MODE 3 */
> +		>;
> +	};
> +};
> -- 
> 1.7.5.4
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Regards,
Nishanth Menon



More information about the linux-arm-kernel mailing list