[PATCH 3/3] dts: Add cpufreq controller node for Exynos5440 SoC

[amit kachhap]

On Fri, Feb 8, 2013 at 8:49 AM, Inderpal Singh
<inderpal.singh at linaro.org> wrote:
> On 8 February 2013 00:03, amit kachhap <amit.kachhap at gmail.com> wrote:
>> On Wed, Feb 6, 2013 at 8:49 PM, Inderpal Singh
>> <inderpal.singh at linaro.org> wrote:
>>> On 7 February 2013 01:09, Amit Daniel Kachhap <amit.daniel at samsung.com> wrote:
>>>> Add cpufreq controller device node for Exynos5440 SoC for passing
>>>> parameters like controller base address, interrupt and cpufreq
>>>> table.
>>>>
>>>> Signed-off-by: Amit Daniel Kachhap <amit.daniel at samsung.com>
>>>> ---
>>>>  arch/arm/boot/dts/exynos5440.dtsi |    9 +++++++++
>>>>  1 file changed, 9 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
>>>> index 024269d..b20b517 100644
>>>> --- a/arch/arm/boot/dts/exynos5440.dtsi
>>>> +++ b/arch/arm/boot/dts/exynos5440.dtsi
>>>> @@ -63,6 +63,15 @@
>>>>
>>>>         };
>>>>
>>>> +       cpufreq at 160000 {
>>>> +               compatible = "samsung,exynos5440-cpufreq";
>>>> +               reg = <0x160000 0x1000>;
>>>> +               interrupts = <0 57 0>;
>>>> +               cpufreq_tbl = < 1200000 1025000
>>>> +                               1000000 975000
>>>> +                               800000  925000 >;
>>>> +       };
>>>> +
>>>
>>> I think cpufreq_tbl should be part of the cpu node as it's the
>>> property of the cpu.
>>> Please refer cpufreq-cpu0 and spear-cpufreq.
>>
>> http://permalink.gmane.org/gmane.linux.kernel.samsung-soc/15364.
>> In this thread same discussion followed. I am not sure what is the
>> correct way but looks like Kukjin concluded this with a timer node
>> separate from the CPU code.
>>
>
> I am only talking about cpufreq_tbl and its nothing but operating
> points for the cpus. It seems its agreed upon to add operating-points
> to cpu node as being done by all other platforms like imx6q, am33xx,
> cpufreq-cpu0 and spear.

Even timer, GIC, cpufreq tbl, pmu etc are all cpu properties. But the
problem is whether to put them in cpu0 or repeat same information in
all cpu nodes as it is common to all cpu's  and not just cpu0. So as
Kukjin kim has put the timer node outside the cpu node so i also
followed the same convention.

Mr Kim,
Any issue in this approach?

Thanks,
Amit Daniel
>
> Thanks,
> Inder
>
>> Thanks,
>> Amit Daniel
>>>
>>>>         serial at B0000 {
>>>>                 compatible = "samsung,exynos4210-uart";
>>>>                 reg = <0xB0000 0x1000>;
>>>> --
>>>> 1.7.10.4
>>>>
>>>> --
>>>> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
>>>> the body of a message to majordomo at vger.kernel.org
>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
>>> the body of a message to majordomo at vger.kernel.org
>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html