[PATCH v2 1/5] media: s5p-tv: Restore vpll clock rate

Mateusz Krawczuk m.krawczuk at partner.samsung.com
Wed Aug 28 09:34:28 EDT 2013


Restore vpll clock rate if start stream fail or stream is off.

Signed-off-by: Mateusz Krawczuk <m.krawczuk at partner.samsung.com>
---
 drivers/media/platform/s5p-tv/sdo_drv.c | 24 ++++++++++++++++++++++--
 1 file changed, 22 insertions(+), 2 deletions(-)

diff --git a/drivers/media/platform/s5p-tv/sdo_drv.c b/drivers/media/platform/s5p-tv/sdo_drv.c
index 0afa90f..b919008 100644
--- a/drivers/media/platform/s5p-tv/sdo_drv.c
+++ b/drivers/media/platform/s5p-tv/sdo_drv.c
@@ -55,6 +55,8 @@ struct sdo_device {
 	struct clk *dacphy;
 	/** clock for control of VPLL */
 	struct clk *fout_vpll;
+	/** vpll rate before sdo stream was on */
+	int vpll_rate;
 	/** regulator for SDO IP power */
 	struct regulator *vdac;
 	/** regulator for SDO plug detection */
@@ -193,17 +195,34 @@ static int sdo_s_power(struct v4l2_subdev *sd, int on)
 
 static int sdo_streamon(struct sdo_device *sdev)
 {
+	int ret;
+
 	/* set proper clock for Timing Generator */
-	clk_set_rate(sdev->fout_vpll, 54000000);
+	sdev->vpll_rate = clk_get_rate(sdev->fout_vpll);
+	ret = clk_set_rate(sdev->fout_vpll, 54000000);
+	if (ret < 0) {
+		dev_err(sdev->dev,
+			"%s: Failed to set vpll rate!\n", __func__);
+		return ret;
+	}
 	dev_info(sdev->dev, "fout_vpll.rate = %lu\n",
 	clk_get_rate(sdev->fout_vpll));
 	/* enable clock in SDO */
 	sdo_write_mask(sdev, SDO_CLKCON, ~0, SDO_TVOUT_CLOCK_ON);
-	clk_enable(sdev->dacphy);
+	ret = clk_prepare_enable(sdev->dacphy);
+	if (ret < 0) {
+		dev_err(sdev->dev,
+			"%s: Failed to prepare and enable clock !\n", __func__);
+		goto fail;
+	}
 	/* enable DAC */
 	sdo_write_mask(sdev, SDO_DAC, ~0, SDO_POWER_ON_DAC);
 	sdo_reg_debug(sdev);
 	return 0;
+fail:
+	sdo_write_mask(sdev, SDO_CLKCON, 0, SDO_TVOUT_CLOCK_ON);
+	clk_set_rate(sdev->fout_vpll, sdev->vpll_rate);
+	return ret;
 }
 
 static int sdo_streamoff(struct sdo_device *sdev)
@@ -220,6 +239,7 @@ static int sdo_streamoff(struct sdo_device *sdev)
 	}
 	if (tries == 0)
 		dev_err(sdev->dev, "failed to stop streaming\n");
+	clk_set_rate(sdev->fout_vpll, sdev->vpll_rate);
 	return tries ? 0 : -EIO;
 }
 
-- 
1.8.1.2




More information about the linux-arm-kernel mailing list