[PATCH v7 05/11] ARM: dts: enable hi4511 with device tree

[Stephen Warren]

On 08/22/2013 12:07 PM, Kevin Hilman wrote:
> [+ DT maintainers]
> 
> Haojian Zhuang <haojian.zhuang at linaro.org> writes:
> 
>> Enable Hisilicon Hi4511 development platform with device tree support.
>>
>> Signed-off-by: Haojian Zhuang <haojian.zhuang at linaro.org>
...
>> +/include/ "skeleton.dtsi"
>> +
>> +/ {
>> +	aliases {
>> +		serial0 = &uart0;
>> +		serial1 = &uart1;
>> +		serial2 = &uart2;
>> +		serial3 = &uart3;
>> +		serial4 = &uart4;
>> +	};
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu0: cpu at 0 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a9";
>> +			reg = <0x0>;
>> +			next-level-cache = <&L2>;
>> +		};
>> +	};
>> +
>> +	osc32k: osc32k {
>> +		compatible = "fixed-clock";
>> +		#clock-cells = <0>;
>> +		clock-frequency = <32768>;
>> +		clock-output-names = "osc32khz";
>> +	};
> 
> ...seems many of the recent users of clocks have grouped them into a
> clocks {} grouping on a "simple-bus".
> 
> DT folks: is there a rule of thumb on how whether these fixed clocks
> should be grouped on a simple bus?

I would expect all the clock node names to be just "clock", since the
node names should describe the type of device not their identity (i.e.
clock name).

In turn, this means that each clock node name needs to use a unit
address ("@nnn") to make them unique. In turn, this means they must have
a reg property since the unit address must match the first entry in the
reg property.

Now I assume these clocks don't have any memory-mapped IO registers, so
they would need an arbitrary reg value rather than a real one. So it
doesn't make sense to place them directly under the root DT node, since
their reg values would make no sense within the context of the
CPU-visible MMIO space that the root node describes.

In this case, it's typical to put all the clock nodes into e.g. a
/clocks node, since that node can introduce a separate numbering-space
for clocks. For example, I'd expect something like:

        clocks {
                #address-cells = <1>;
                #size-cells = <0>;

                osc32k: clock at 0 {
                        compatible = "fixed-clock";
                        reg = <0>;
                        #clock-cells = <0>;
                        clock-frequency = <32768>;
                        clock-output-names = "osc32khz";
                };

                osc26m: clock at 1 {
                        compatible = "fixed-clock";
                        reg = <1>;
                        #clock-cells = <0>;
                        clock-frequency = <26000000>;
                        clock-output-names = "osc26mhz";
                };
                ...
        };

However, it also depends on what is actually providing those clocks. If
every one of them is some standalone device on the board (e.g. a
crystal), then just dumping them all in /clocks makes sense. However, if
the clocks are provided by some on-SoC clock module, then I'd likely
expect the clocks to be contained within the DT node that represents
that clock module, which presumably does have some registers, and hence
could be a direct child of the root node. For example, I wonder if the
following is more accurate:

	sctrl: sctrl at fc802000 {
		compatible = "hisilicon,sctrl";
		reg = <0xfc802000 0x1000>;
                #address-cells = <1>;
                #size-cells = <0>;

                osc32k: clock at 0 {
                        compatible = "fixed-clock";
                        reg = <0>;
                        #clock-cells = <0>;
                        clock-frequency = <32768>;
                        clock-output-names = "osc32khz";
                };

                osc26m: clock at 1 {
                        compatible = "fixed-clock";
                        reg = <1>;
                        #clock-cells = <0>;
                        clock-frequency = <26000000>;
                        clock-output-names = "osc26mhz";
                };
                ...
        };

... since I see there are already quite a few clocks inside the sctrl node.