[PATCH] ARM: DRA7: dts: Add the dts files for dra7 SoC and dra7-evm board

Rajendra Nayak rnayak at ti.com
Wed Aug 14 06:25:29 EDT 2013


From: R Sricharan <r.sricharan at ti.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.

Signed-off-by: R Sricharan <r.sricharan at ti.com>
Signed-off-by: Rajendra Nayak <rnayak at ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
---
Benoit, I am reposting the dts files for dra so you can pick it up
for 3.12.
Rest of the core support is already pulled in by Tony.

 arch/arm/boot/dts/Makefile        |    3 +-
 arch/arm/boot/dts/dra7-evm.dts    |  140 +++++++++
 arch/arm/boot/dts/dra7.dtsi       |  574 +++++++++++++++++++++++++++++++++++++
 include/dt-bindings/pinctrl/dra.h |   45 +++
 4 files changed, 761 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/dra7-evm.dts
 create mode 100644 arch/arm/boot/dts/dra7.dtsi
 create mode 100644 include/dt-bindings/pinctrl/dra.h

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 641b3c9..e2f8566 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -173,7 +173,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-bone.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
-	am43x-epos-evm.dtb
+	am43x-epos-evm.dtb \
+	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
new file mode 100644
index 0000000..dae33d0
--- /dev/null
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -0,0 +1,140 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra7.dtsi"
+
+/ {
+	model = "TI DRA7";
+	compatible = "ti,dra7-evm", "ti,dra752", "ti,dra7";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x60000000>; /* 1536 MB */
+	};
+};
+
+&dra7_pmx_core {
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
+			0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+			0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
+			0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
+			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
+			0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
+			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+			0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
+			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
+			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
+		>;
+	};
+
+	mcspi2_pins: pinmux_mcspi2_pins {
+		pinctrl-single,pins = <
+			0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */
+			0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
+			0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
+			0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
+			0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */
+			0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */
+			0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
+			0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
+			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <400000>;
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <3400000>;
+};
+
+&mcspi1 {
+        status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+};
+
+&mcspi2 {
+        status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi2_pins>;
+};
+
+&uart1 {
+	status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
new file mode 100644
index 0000000..ad18fb2
--- /dev/null
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -0,0 +1,574 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * Based on "omap4.dtsi"
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/dra.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	compatible = "ti,dra7xx";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+		};
+		cpu at 1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	gic: interrupt-controller at 48211000 {
+		compatible = "arm,cortex-a15-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48211000 0x1000>,
+		      <0x48212000 0x1000>,
+		      <0x48214000 0x2000>,
+		      <0x48216000 0x2000>;
+	};
+
+	/*
+	 * The soc node represents the soc top level view. It is uses for IPs
+	 * that are not memory mapped in the MPU view or for the MPU itself.
+	 */
+	soc {
+		compatible = "ti,omap-infra";
+		mpu {
+			compatible = "ti,omap5-mpu";
+			ti,hwmods = "mpu";
+		};
+	};
+
+	/*
+	 * XXX: Use a flat representation of the SOC interconnect.
+	 * The real OMAP interconnect network is quite complex.
+	 * Since that will not bring real advantage to represent that in DT for
+	 * the moment, just use a fake OCP bus entry to represent the whole bus
+	 * hierarchy.
+	 */
+	ocp {
+		compatible = "ti,omap4-l3-noc", "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		ti,hwmods = "l3_main_1", "l3_main_2";
+		reg = <0x44000000 0x2000>,
+		      <0x44800000 0x3000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+
+		counter32k: counter at 4ae04000 {
+			compatible = "ti,omap-counter32k";
+			reg = <0x4ae04000 0x40>;
+			ti,hwmods = "counter_32k";
+		};
+
+		dra7_pmx_core: pinmux at 4a003400 {
+			compatible = "pinctrl-single";
+			reg = <0x4a003400 0x0464>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <0x3fffffff>;
+		};
+
+		sdma: dma-controller at 4a056000 {
+			compatible = "ti,omap4430-sdma";
+			reg = <0x4a056000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			#dma-channels = <32>;
+			#dma-requests = <127>;
+		};
+
+		gpio1: gpio at 4ae10000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x4ae10000 0x200>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio1";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio2: gpio at 48055000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x48055000 0x200>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio2";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio3: gpio at 48057000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x48057000 0x200>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio3";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio4: gpio at 48059000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x48059000 0x200>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio4";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio5: gpio at 4805b000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x4805b000 0x200>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio5";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio6: gpio at 4805d000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x4805d000 0x200>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio6";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio7: gpio at 48051000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x48051000 0x200>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio7";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		gpio8: gpio at 48053000 {
+			compatible = "ti,omap4-gpio";
+			reg = <0x48053000 0x200>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "gpio8";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		uart1: serial at 4806a000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x4806a000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart1";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart2: serial at 4806c000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x4806c000 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart2";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart3: serial at 48020000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48020000 0x100>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart3";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart4: serial at 4806e000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x4806e000 0x100>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart4";
+			clock-frequency = <48000000>;
+                        status = "disabled";
+		};
+
+		uart5: serial at 48066000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48066000 0x100>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart5";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart6: serial at 48068000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48068000 0x100>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart6";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart7: serial at 48420000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48420000 0x100>;
+			ti,hwmods = "uart7";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart8: serial at 48422000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48422000 0x100>;
+			ti,hwmods = "uart8";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart9: serial at 48424000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x48424000 0x100>;
+			ti,hwmods = "uart9";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		uart10: serial at 4ae2b000 {
+			compatible = "ti,omap4-uart";
+			reg = <0x4ae2b000 0x100>;
+			ti,hwmods = "uart10";
+			clock-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		timer1: timer at 4ae18000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x4ae18000 0x80>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer1";
+			ti,timer-alwon;
+		};
+
+		timer2: timer at 48032000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48032000 0x80>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer2";
+		};
+
+		timer3: timer at 48034000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48034000 0x80>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer3";
+		};
+
+		timer4: timer at 48036000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48036000 0x80>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer4";
+		};
+
+		timer5: timer at 48820000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48820000 0x80>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer5";
+			ti,timer-dsp;
+		};
+
+		timer6: timer at 48822000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48822000 0x80>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer6";
+			ti,timer-dsp;
+			ti,timer-pwm;
+		};
+
+		timer7: timer at 48824000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48824000 0x80>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer7";
+			ti,timer-dsp;
+		};
+
+		timer8: timer at 48826000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48826000 0x80>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer8";
+			ti,timer-dsp;
+			ti,timer-pwm;
+		};
+
+		timer9: timer at 4803e000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x4803e000 0x80>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer9";
+		};
+
+		timer10: timer at 48086000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48086000 0x80>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer10";
+		};
+
+		timer11: timer at 48088000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48088000 0x80>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer11";
+			ti,timer-pwm;
+		};
+
+		timer13: timer at 48828000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x48828000 0x80>;
+			ti,hwmods = "timer13";
+			status = "disabled";
+		};
+
+		timer14: timer at 4882a000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x4882a000 0x80>;
+			ti,hwmods = "timer14";
+			status = "disabled";
+		};
+
+		timer15: timer at 4882c000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x4882c000 0x80>;
+			ti,hwmods = "timer15";
+			status = "disabled";
+		};
+
+		timer16: timer at 4882e000 {
+			compatible = "ti,omap5430-timer";
+			reg = <0x4882e000 0x80>;
+			ti,hwmods = "timer16";
+			status = "disabled";
+		};
+
+		wdt2: wdt at 4ae14000 {
+			compatible = "ti,omap4-wdt";
+			reg = <0x4ae14000 0x80>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "wd_timer2";
+		};
+
+		i2c1: i2c at 48070000 {
+			compatible = "ti,omap4-i2c";
+			reg = <0x48070000 0x100>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "i2c1";
+			status = "disabled";
+		};
+
+		i2c2: i2c at 48072000 {
+			compatible = "ti,omap4-i2c";
+			reg = <0x48072000 0x100>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "i2c2";
+			status = "disabled";
+		};
+
+		i2c3: i2c at 48060000 {
+			compatible = "ti,omap4-i2c";
+			reg = <0x48060000 0x100>;
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "i2c3";
+			status = "disabled";
+		};
+
+		i2c4: i2c at 4807a000 {
+			compatible = "ti,omap4-i2c";
+			reg = <0x4807a000 0x100>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "i2c4";
+			status = "disabled";
+		};
+
+		i2c5: i2c at 4807c000 {
+			compatible = "ti,omap4-i2c";
+			reg = <0x4807c000 0x100>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "i2c5";
+			status = "disabled";
+		};
+
+		mmc1: mmc at 4809c000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x4809c000 0x400>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			dmas = <&sdma 61>, <&sdma 62>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		mmc2: mmc at 480b4000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x480b4000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&sdma 47>, <&sdma 48>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		mmc3: mmc at 480ad000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x480ad000 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			dmas = <&sdma 77>, <&sdma 78>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		mmc4: mmc at 480d1000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x480d1000 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mmc4";
+			ti,needs-special-reset;
+			dmas = <&sdma 57>, <&sdma 58>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		mcspi1: spi at 48098000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x48098000 0x200>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi1";
+			ti,spi-num-cs = <4>;
+			dmas = <&sdma 35>,
+			       <&sdma 36>,
+			       <&sdma 37>,
+			       <&sdma 38>,
+			       <&sdma 39>,
+			       <&sdma 40>,
+			       <&sdma 41>,
+			       <&sdma 42>;
+			dma-names = "tx0", "rx0", "tx1", "rx1",
+				    "tx2", "rx2", "tx3", "rx3";
+			status = "disabled";
+		};
+
+		mcspi2: spi at 4809a000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x4809a000 0x200>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi2";
+			ti,spi-num-cs = <2>;
+			dmas = <&sdma 43>,
+			       <&sdma 44>,
+			       <&sdma 45>,
+			       <&sdma 46>;
+			dma-names = "tx0", "rx0", "tx1", "rx1";
+			status = "disabled";
+		};
+
+		mcspi3: spi at 480b8000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x480b8000 0x200>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi3";
+			ti,spi-num-cs = <2>;
+			dmas = <&sdma 15>, <&sdma 16>;
+			dma-names = "tx0", "rx0";
+			status = "disabled";
+		};
+
+		mcspi4: spi at 480ba000 {
+			compatible = "ti,omap4-mcspi";
+			reg = <0x480ba000 0x200>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "mcspi4";
+			ti,spi-num-cs = <1>;
+			dmas = <&sdma 70>, <&sdma 71>;
+			dma-names = "tx0", "rx0";
+			status = "disabled";
+		};
+	};
+};
diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h
new file mode 100644
index 0000000..d0ad97b
--- /dev/null
+++ b/include/dt-bindings/pinctrl/dra.h
@@ -0,0 +1,45 @@
+/*
+ * This header provides constants for DRA pinctrl bindings.
+ *
+ * Copyright (C) 2013 Texas Instruments
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_DRA_H
+#define _DT_BINDINGS_PINCTRL_DRA_H
+
+/* DRA7 mux mode options for each pin. See TRM for options */
+#define MUX_MODE0	0x0
+#define MUX_MODE1	0x1
+#define MUX_MODE2	0x2
+#define MUX_MODE3	0x3
+#define MUX_MODE4	0x4
+#define MUX_MODE5	0x5
+#define MUX_MODE6	0x6
+#define MUX_MODE7	0x7
+#define MUX_MODE8	0x8
+#define MUX_MODE9	0x9
+#define MUX_MODE10	0xa
+#define MUX_MODE11	0xb
+#define MUX_MODE12	0xc
+#define MUX_MODE13	0xd
+#define MUX_MODE14	0xe
+#define MUX_MODE15	0xf
+
+#define PULL_ENA		(1 << 16)
+#define PULL_UP			(1 << 17)
+#define INPUT_EN		(1 << 18)
+#define SLEWCONTROL		(1 << 19)
+#define WAKEUP_EN		(1 << 24)
+#define WAKEUP_EVENT		(1 << 25)
+
+/* Active pin states */
+#define PIN_OUTPUT		0
+#define PIN_OUTPUT_PULLUP	(PIN_OUTPUT | PULL_ENA | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN	(PIN_OUTPUT | PULL_ENA)
+#define PIN_INPUT		INPUT_EN
+#define PIN_INPUT_SLEW		(INPUT_EN | SLEWCONTROL)
+#define PIN_INPUT_PULLUP	(PULL_ENA | INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN	(PULL_ENA | INPUT_EN)
+
+#endif
+
-- 
1.7.9.5




More information about the linux-arm-kernel mailing list