[PATCH v2 5/6] spi: s3c64xx: Remove the 'set_level' callback from controller data

Thomas Abraham thomas.abraham at linaro.org
Fri May 18 05:33:32 EDT 2012


The set_level callback in the controller data, which is used to configure
the slave select line, cannot be supported when migrating the driver to
device tree based discovery. Since all the platforms currently use gpio
as the slave select line, this callback can be removed from the
controller data and replaced with call to gpio_set_value in the driver.

Signed-off-by: Thomas Abraham <thomas.abraham at linaro.org>
Acked-by: Jaswinder Singh <jaswinder.singh at linaro.org>
---
 arch/arm/plat-samsung/include/plat/s3c64xx-spi.h |    2 --
 drivers/spi/spi-s3c64xx.c                        |    8 ++++----
 2 files changed, 4 insertions(+), 6 deletions(-)

diff --git a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
index a733ce9..48a6495 100644
--- a/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
+++ b/arch/arm/plat-samsung/include/plat/s3c64xx-spi.h
@@ -18,7 +18,6 @@ struct platform_device;
  * @fb_delay: Slave specific feedback delay.
  *            Refer to FB_CLK_SEL register definition in SPI chapter.
  * @line: Custom 'identity' of the CS line.
- * @set_level: CS line control.
  *
  * This is per SPI-Slave Chipselect information.
  * Allocate and initialize one in machine init code and make the
@@ -27,7 +26,6 @@ struct platform_device;
 struct s3c64xx_spi_csinfo {
 	u8 fb_delay;
 	unsigned line;
-	void (*set_level)(unsigned line_id, int lvl);
 };
 
 /**
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
index f6bc0e3..d84ce7f 100644
--- a/drivers/spi/spi-s3c64xx.c
+++ b/drivers/spi/spi-s3c64xx.c
@@ -406,14 +406,14 @@ static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd,
 		if (sdd->tgl_spi != spi) { /* if last mssg on diff device */
 			/* Deselect the last toggled device */
 			cs = sdd->tgl_spi->controller_data;
-			cs->set_level(cs->line,
-					spi->mode & SPI_CS_HIGH ? 0 : 1);
+			gpio_set_value(cs->line,
+				spi->mode & SPI_CS_HIGH ? 0 : 1);
 		}
 		sdd->tgl_spi = NULL;
 	}
 
 	cs = spi->controller_data;
-	cs->set_level(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
+	gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0);
 }
 
 static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd,
@@ -499,7 +499,7 @@ static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd,
 	if (sdd->tgl_spi == spi)
 		sdd->tgl_spi = NULL;
 
-	cs->set_level(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
+	gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1);
 }
 
 static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
-- 
1.6.6.rc2




More information about the linux-arm-kernel mailing list