[PATCH 2/3] ARM: PXA27x: save/restore PWER on suspend/resume

[Russell King - ARM Linux]

On Mon, Feb 27, 2012 at 12:47:01AM +0100, Marek Vasut wrote:
> > On Sun, Feb 26, 2012 at 11:20:27PM +0100, Marek Vasut wrote:
> > > > On Sun, Feb 26, 2012 at 04:47:41PM +0300, Vasily Khoruzhick wrote:
> > > > > Bootloader can clobber PWER value, so save it state on suspend.
> > > > 
> > > > What boot loader is this,
> > > 
> > > U-Boot, patched, not mainline.
> > > 
> > > > and why is it being so idiotic?
> > > 
> > > Mainline doesn't touch PWER, so please be careful about your accusations.
> > > 
> > > > Why can't it
> > > > be fixed?
> > > 
> > > Yes, either by using mainline uboot (to rule out the bootloader problem),
> > > finding bug in linux kernel or reading the CPU manual.
> > 
> > Was there supposed to be any useful information in your reply, or are
> > you just trying to be your usual antagonistic self?
> 
> Um ... 
> 
> 1) PWER isn't reconfigured by uboot (see above)

Given that virtually everyone seems to use a modified version of uboot,
how can you be so sure?

> 2) That you should try mainline uboot to avoid debugging problems with not-
> mainlined patches

Why should _I_ try anything with uboot?  I'm not the one experiencing
problems.

I'll point out that Vasily is reporting that _his_ boot loader, whatever
it is, is clobbering the PWER register.  That's *his* statement in the
commit log, and I have no reason *not* to think that he's put in the
research to confirm that.  Otherwise, why make such a positive statement
about where the problem lies?

> 3) That the bug with PWER is likely in kernel, since there's an issue with 
> gpio_set_wake() on PXA

I've reviewed this function and its associated data, and can't see
anything wrong with it (see below).

> 4) That the CPU might not preserve PWER throughout the suspend and that this 
> information might be found in the CPU manual

No.  The PXA270 manual says that this register is preserved on exit from
deep sleep and sleep modes.  It appends a note against each bit in the
reset status for the PWER register which says "Exit from sleep or
deep sleep mode does not clear or set this bit".

The setup for GPIO0 is:

        for (i = 0; i <= 15; i++) {
                /* skip GPIO2, 5, 6, 7, 8 */
                if (GPIO_bit(i) & 0x1e4)
                        continue;

                gpio_desc[i].can_wakeup = 1;
                gpio_desc[i].mask = GPIO_bit(i);
        }

So, gpio_desc[0].can_wakeup = 1 and gpio_desc[0].mask is the bitmask for
GPIO0.

gpio_set_wake() does this:

        d = &gpio_desc[gpio];
        c = d->config;

        if (!d->valid)
                return -EINVAL;

well, that's already been set valid by pxa27x_mfp_init().

        if (d->keypad_gpio && (MFP_AF(d->config) == 0) &&

it's not a keypad gpio...

        mux_taken = (PWER & d->mux_mask) & (~d->mask);
        if (on && mux_taken)
                return -EBUSY;

well, d->mux_mask is zero, so this check fails.

        if (d->can_wakeup && (c & MFP_LPM_CAN_WAKEUP)) {
                if (on) {
                        PWER = (PWER & ~d->mux_mask) | d->mask;

Now, we know d->can_wakeup is true.  However, what about the MFP
configuration?

Well, that depends on the platform.  I suspect that's where the problem
with wakeup sources not working is located, because the MFP configuration
hasn't been properly set, and that comes from platform code.

So please, stop blaming PXA code without full and proper analysis of
bugs.  It's a waste of everyone's time, and it hurts proper kernel
maintenance if these ill-researched 'workarounds' get merged instead
of proper fixes.