[GIT PULL] omap cleanup part1 for v3.2 merge window

[Tony Lindgren]

Arnd,

* Kevin Hilman <khilman at ti.com> [110921 09:09]:
> Hi Arnd,
> 
> Arnd Bergmann <arnd at arndb.de> writes:
> 
> > On Tuesday 20 September 2011 23:46:11 Arnd Bergmann wrote:
> >
> >> It seems that you replace the #ifdef in the board-flash.c file
> >> with a similar #ifdef in the header that replaces this with an
> >> empty inline function when the object is not built.
> >
> > Found another similar problem over night, presumably in the voltage series:
> >
> 
> Found.  Patch below.
> 
> If this one is OK, I'll push to my for_3.2/voltage-cleanup branch (which
> is already pulled into arm-soc/next/voltage) so just re-pulling will
> pick up the fix.

Arnd, care to pull this in directly from Kevin into voltage branch?
It's available at:

git://gitorious.org/khilman/linux-omap-pm for_3.2/voltage-cleanup

Regards,

Tony


> From 473dc975c3ea468049732155467ff08fe3701f98 Mon Sep 17 00:00:00 2001
> From: Kevin Hilman <khilman at ti.com>
> Date: Wed, 21 Sep 2011 09:24:53 -0700
> Subject: [PATCH] ARM: OMAP: voltage layer present, even when CONFIG_PM=n
> 
> Even when CONFIG_PM=n, we try to scale the boot voltage to a sane,
> known value using OPP table to find matching voltage based on boot
> frequency.  This should be done, even when CONFIG_PM=n to avoid
> mis-configured bootloaders and/or boot voltage assumptions made by
> boot loaders.
> 
> Also fixes various compile problems due to depenencies between voltage
> domain and powerdomain code (also present when CONFIG_PM=n).
> 
> Reported-by: Arnd Bergmann <arnd at arndb.de>
> Signed-off-by: Kevin Hilman <khilman at ti.com>
> ---
> Compile tested with CONFIG_PM=n
> Applies to arm-soc/next/voltage
> 
>  arch/arm/mach-omap2/Makefile  |    2 --
>  arch/arm/mach-omap2/voltage.h |   14 --------------
>  2 files changed, 0 insertions(+), 16 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
> index 8bd389d..5129785 100644
> --- a/arch/arm/mach-omap2/Makefile
> +++ b/arch/arm/mach-omap2/Makefile
> @@ -89,7 +89,6 @@ obj-$(CONFIG_ARCH_OMAP4)		+= prcm.o cm2xxx_3xxx.o cminst44xx.o \
>  					   vp44xx_data.o
>  
>  # OMAP voltage domains
> -ifeq ($(CONFIG_PM),y)
>  voltagedomain-common			:= voltage.o vc.o vp.o
>  obj-$(CONFIG_ARCH_OMAP2)		+= $(voltagedomain-common) \
>  					   voltagedomains2xxx_data.o
> @@ -97,7 +96,6 @@ obj-$(CONFIG_ARCH_OMAP3)		+= $(voltagedomain-common) \
>  					   voltagedomains3xxx_data.o
>  obj-$(CONFIG_ARCH_OMAP4)		+= $(voltagedomain-common) \
>  					   voltagedomains44xx_data.o
> -endif
>  
>  # OMAP powerdomain framework
>  powerdomain-common			+= powerdomain.o powerdomain-common.o
> diff --git a/arch/arm/mach-omap2/voltage.h b/arch/arm/mach-omap2/voltage.h
> index 4c09809..16a1b09 100644
> --- a/arch/arm/mach-omap2/voltage.h
> +++ b/arch/arm/mach-omap2/voltage.h
> @@ -148,25 +148,11 @@ void omap_voltage_get_volttable(struct voltagedomain *voltdm,
>  		struct omap_volt_data **volt_data);
>  struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
>  		unsigned long volt);
> -#ifdef CONFIG_PM
>  int omap_voltage_register_pmic(struct voltagedomain *voltdm,
>  			       struct omap_voltdm_pmic *pmic);
>  void omap_change_voltscale_method(struct voltagedomain *voltdm,
>  		int voltscale_method);
>  int omap_voltage_late_init(void);
> -#else
> -static inline int omap_voltage_register_pmic(struct voltagedomain *voltdm,
> -					     struct omap_voltdm_pmic *pmic)
> -{
> -	return -EINVAL;
> -}
> -static inline  void omap_change_voltscale_method(struct voltagedomain *voltdm,
> -		int voltscale_method) {}
> -static inline int omap_voltage_late_init(void)
> -{
> -	return -EINVAL;
> -}
> -#endif
>  
>  extern void omap2xxx_voltagedomains_init(void);
>  extern void omap3xxx_voltagedomains_init(void);
> -- 
> 1.7.6
>