[PATCH 4/4] pxa/spitz: Rework spitz
Marek Vasut
marek.vasut at gmail.com
Thu Jun 24 10:02:12 EDT 2010
This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:
1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
similar code. The kernel size will grow by a few kb now, but the file is much
more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: Marek Vasut <marek.vasut at gmail.com>
---
arch/arm/mach-pxa/include/mach/spitz.h | 2 -
arch/arm/mach-pxa/spitz.c | 813 ++++++++++++++++++--------------
2 files changed, 470 insertions(+), 345 deletions(-)
diff --git a/arch/arm/mach-pxa/include/mach/spitz.h b/arch/arm/mach-pxa/include/mach/spitz.h
index fa1998c..685749a 100644
--- a/arch/arm/mach-pxa/include/mach/spitz.h
+++ b/arch/arm/mach-pxa/include/mach/spitz.h
@@ -185,7 +185,5 @@
/*
* Shared data structures
*/
-extern struct platform_device spitzscoop_device;
-extern struct platform_device spitzscoop2_device;
extern struct platform_device spitzssp_device;
extern struct sharpsl_charger_machinfo spitz_pm_machinfo;
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index c1048a3..fa31980 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -18,14 +18,15 @@
#include <linux/gpio_keys.h>
#include <linux/gpio.h>
#include <linux/leds.h>
-#include <linux/mtd/physmap.h>
#include <linux/i2c.h>
#include <linux/i2c/pca953x.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
+#include <linux/mtd/physmap.h>
#include <linux/mtd/sharpsl.h>
#include <linux/input/matrix_keypad.h>
+#include <linux/regulator/machine.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -33,11 +34,9 @@
#include <asm/mach/sharpsl_param.h>
#include <asm/hardware/scoop.h>
-
#include <mach/pxa27x.h>
#include <mach/pxa27x-udc.h>
#include <mach/reset.h>
-#include <plat/i2c.h>
#include <mach/irda.h>
#include <mach/mmc.h>
#include <mach/ohci.h>
@@ -45,11 +44,16 @@
#include <mach/pxa2xx_spi.h>
#include <mach/spitz.h>
+#include <plat/i2c.h>
+
#include "generic.h"
#include "devices.h"
#include "sharpsl.h"
-static unsigned long spitz_pin_config[] __initdata = {
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long sharpslc_pin_config[] __initdata = {
/* Chip Selects */
GPIO78_nCS_2, /* SCOOP #2 */
GPIO79_nCS_3, /* NAND */
@@ -124,10 +128,13 @@ static unsigned long spitz_pin_config[] __initdata = {
GPIO1_GPIO | WAKEUP_ON_EDGE_FALL, /* SPITZ_GPIO_RESET */
};
-/*
- * Spitz SCOOP Device #1
- */
-static struct resource spitz_scoop_resources[] = {
+
+/******************************************************************************
+ * Scoop GPIO expander
+ ******************************************************************************/
+#if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
+/* SCOOP Device #1 */
+static struct resource sharpslc_scoop_1_resources[] = {
[0] = {
.start = 0x10800000,
.end = 0x10800fff,
@@ -135,7 +142,7 @@ static struct resource spitz_scoop_resources[] = {
},
};
-static struct scoop_config spitz_scoop_setup = {
+static struct scoop_config sharpslc_scoop_1_setup = {
.io_dir = SPITZ_SCP_IO_DIR,
.io_out = SPITZ_SCP_IO_OUT,
.suspend_clr = SPITZ_SCP_SUS_CLR,
@@ -143,20 +150,18 @@ static struct scoop_config spitz_scoop_setup = {
.gpio_base = SPITZ_SCP_GPIO_BASE,
};
-struct platform_device spitzscoop_device = {
+struct platform_device sharpslc_scoop_1_device = {
.name = "sharp-scoop",
.id = 0,
.dev = {
- .platform_data = &spitz_scoop_setup,
+ .platform_data = &sharpslc_scoop_1_setup,
},
- .num_resources = ARRAY_SIZE(spitz_scoop_resources),
- .resource = spitz_scoop_resources,
+ .num_resources = ARRAY_SIZE(sharpslc_scoop_1_resources),
+ .resource = sharpslc_scoop_1_resources,
};
-/*
- * Spitz SCOOP Device #2
- */
-static struct resource spitz_scoop2_resources[] = {
+/* SCOOP Device #2 */
+static struct resource sharpslc_scoop_2_resources[] = {
[0] = {
.start = 0x08800040,
.end = 0x08800fff,
@@ -164,7 +169,7 @@ static struct resource spitz_scoop2_resources[] = {
},
};
-static struct scoop_config spitz_scoop2_setup = {
+static struct scoop_config sharpslc_scoop_2_setup = {
.io_dir = SPITZ_SCP2_IO_DIR,
.io_out = SPITZ_SCP2_IO_OUT,
.suspend_clr = SPITZ_SCP2_SUS_CLR,
@@ -172,82 +177,110 @@ static struct scoop_config spitz_scoop2_setup = {
.gpio_base = SPITZ_SCP2_GPIO_BASE,
};
-struct platform_device spitzscoop2_device = {
+struct platform_device sharpslc_scoop_2_device = {
.name = "sharp-scoop",
.id = 1,
.dev = {
- .platform_data = &spitz_scoop2_setup,
+ .platform_data = &sharpslc_scoop_2_setup,
},
- .num_resources = ARRAY_SIZE(spitz_scoop2_resources),
- .resource = spitz_scoop2_resources,
+ .num_resources = ARRAY_SIZE(sharpslc_scoop_2_resources),
+ .resource = sharpslc_scoop_2_resources,
};
-#define SPITZ_PWR_SD 0x01
-#define SPITZ_PWR_CF 0x02
+static void __init sharpslc_scoop_init(void)
+{
+ platform_device_register(&sharpslc_scoop_1_device);
+
+ /* Akita doesn't have the second SCOOP chip */
+ if (!machine_is_akita())
+ platform_device_register(&sharpslc_scoop_2_device);
+}
/* Power control is shared with between one of the CF slots and SD */
-static void spitz_card_pwr_ctrl(int device, unsigned short new_cpr)
+static void sharpslc_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
{
- unsigned short cpr = read_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR);
+ unsigned short cpr;
+ unsigned long flags;
- if (new_cpr & 0x0007) {
+ if (new_cpr & 0x7) {
gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
- if (!(cpr & 0x0002) && !(cpr & 0x0004))
- mdelay(5);
- if (device == SPITZ_PWR_CF)
- cpr |= 0x0002;
- if (device == SPITZ_PWR_SD)
- cpr |= 0x0004;
- write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr | new_cpr);
- } else {
- if (device == SPITZ_PWR_CF)
- cpr &= ~0x0002;
- if (device == SPITZ_PWR_SD)
- cpr &= ~0x0004;
- if (!(cpr & 0x0002) && !(cpr & 0x0004)) {
- write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, 0x0000);
- mdelay(1);
- gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
- } else {
- write_scoop_reg(&spitzscoop_device.dev, SCOOP_CPR, cpr | new_cpr);
- }
+ mdelay(5);
+ }
+
+ local_irq_save(flags);
+
+ cpr = read_scoop_reg(&sharpslc_scoop_1_device.dev, SCOOP_CPR);
+
+ if (enable & new_cpr)
+ cpr |= new_cpr;
+ else
+ cpr &= ~enable;
+
+ write_scoop_reg(&sharpslc_scoop_1_device.dev, SCOOP_CPR, cpr);
+
+ local_irq_restore(flags);
+
+ if (!(cpr & 0x7)) {
+ mdelay(1);
+ gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
}
}
-static void spitz_pcmcia_pwr(struct device *scoop, unsigned short cpr, int nr)
+#else
+static inline void sharpslc_scoop_init(void) {}
+static inline void sharpslc_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) {}
+#endif
+
+/******************************************************************************
+ * PCMCIA
+ ******************************************************************************/
+#if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
+static void sharpslc_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr)
{
/* Only need to override behaviour for slot 0 */
if (nr == 0)
- spitz_card_pwr_ctrl(SPITZ_PWR_CF, cpr);
+ sharpslc_card_pwr_ctrl(
+ cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr);
else
write_scoop_reg(scoop, SCOOP_CPR, cpr);
}
-static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
-{
- .dev = &spitzscoop_device.dev,
- .irq = SPITZ_IRQ_GPIO_CF_IRQ,
- .cd_irq = SPITZ_IRQ_GPIO_CF_CD,
- .cd_irq_str = "PCMCIA0 CD",
-},{
- .dev = &spitzscoop2_device.dev,
- .irq = SPITZ_IRQ_GPIO_CF2_IRQ,
- .cd_irq = -1,
-},
+static struct scoop_pcmcia_dev sharpslc_pcmcia_scoop[] = {
+ {
+ .dev = &sharpslc_scoop_1_device.dev,
+ .irq = SPITZ_IRQ_GPIO_CF_IRQ,
+ .cd_irq = SPITZ_IRQ_GPIO_CF_CD,
+ .cd_irq_str = "PCMCIA0 CD",
+ }, {
+ .dev = &sharpslc_scoop_2_device.dev,
+ .irq = SPITZ_IRQ_GPIO_CF2_IRQ,
+ .cd_irq = -1,
+ },
};
-static struct scoop_pcmcia_config spitz_pcmcia_config = {
- .devs = &spitz_pcmcia_scoop[0],
- .num_devs = 2,
- .power_ctrl = spitz_pcmcia_pwr,
+static struct scoop_pcmcia_config sharpslc_pcmcia_config = {
+ .devs = &sharpslc_pcmcia_scoop[0],
+ .num_devs = 2,
+ .power_ctrl = sharpslc_pcmcia_pwr,
};
-EXPORT_SYMBOL(spitzscoop_device);
-EXPORT_SYMBOL(spitzscoop2_device);
+static void __init sharpslc_pcmcia_init(void)
+{
+ /* Akita has only one PCMCIA slot used */
+ if (machine_is_akita())
+ sharpslc_pcmcia_config.num_devs = 1;
+
+ platform_scoop_config = &sharpslc_pcmcia_config;
+}
+#else
+static inline void sharpslc_pcmcia_init(void) {}
+#endif
+
+/******************************************************************************
+ * GPIO keyboard
+ ******************************************************************************/
+#if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
-/*
- * Spitz Keyboard Device
- */
#define SPITZ_KEY_CALENDAR KEY_F1
#define SPITZ_KEY_ADDRESS KEY_F2
#define SPITZ_KEY_FN KEY_F3
@@ -263,7 +296,7 @@ EXPORT_SYMBOL(spitzscoop2_device);
#define SPITZ_KEY_OK KEY_F11
#define SPITZ_KEY_MENU KEY_F12
-static const uint32_t spitzkbd_keymap[] = {
+static const uint32_t sharpslc_keymap[] = {
KEY(0, 0, KEY_LEFTCTRL),
KEY(0, 1, KEY_1),
KEY(0, 2, KEY_3),
@@ -330,37 +363,48 @@ static const uint32_t spitzkbd_keymap[] = {
KEY(6, 8, KEY_RIGHT),
};
-static const struct matrix_keymap_data spitzkbd_keymap_data = {
- .keymap = spitzkbd_keymap,
- .keymap_size = ARRAY_SIZE(spitzkbd_keymap),
+static const struct matrix_keymap_data sharpslc_keymap_data = {
+ .keymap = sharpslc_keymap,
+ .keymap_size = ARRAY_SIZE(sharpslc_keymap),
};
-static const uint32_t spitzkbd_row_gpios[] =
+static const uint32_t sharpslc_row_gpios[] =
{ 12, 17, 91, 34, 36, 38, 39 };
-static const uint32_t spitzkbd_col_gpios[] =
+static const uint32_t sharpslc_col_gpios[] =
{ 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
-static struct matrix_keypad_platform_data spitzkbd_pdata = {
- .keymap_data = &spitzkbd_keymap_data,
- .row_gpios = spitzkbd_row_gpios,
- .col_gpios = spitzkbd_col_gpios,
- .num_row_gpios = ARRAY_SIZE(spitzkbd_row_gpios),
- .num_col_gpios = ARRAY_SIZE(spitzkbd_col_gpios),
+static struct matrix_keypad_platform_data sharpslc_mkp_pdata = {
+ .keymap_data = &sharpslc_keymap_data,
+ .row_gpios = sharpslc_row_gpios,
+ .col_gpios = sharpslc_col_gpios,
+ .num_row_gpios = ARRAY_SIZE(sharpslc_row_gpios),
+ .num_col_gpios = ARRAY_SIZE(sharpslc_col_gpios),
.col_scan_delay_us = 10,
.debounce_ms = 10,
.wakeup = 1,
};
-static struct platform_device spitzkbd_device = {
+static struct platform_device sharpslc_mkp_device = {
.name = "matrix-keypad",
.id = -1,
.dev = {
- .platform_data = &spitzkbd_pdata,
+ .platform_data = &sharpslc_mkp_pdata,
},
};
+static void __init sharpslc_mkp_init(void)
+{
+ platform_device_register(&sharpslc_mkp_device);
+}
+#else
+static inline void sharpslc_mkp_init(void) {}
+#endif
-static struct gpio_keys_button spitz_gpio_keys[] = {
+/******************************************************************************
+ * GPIO keys
+ ******************************************************************************/
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+static struct gpio_keys_button sharpslc_gpio_keys[] = {
{
.type = EV_PWR,
.code = KEY_SUSPEND,
@@ -383,27 +427,35 @@ static struct gpio_keys_button spitz_gpio_keys[] = {
},
};
-static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = {
- .buttons = spitz_gpio_keys,
- .nbuttons = ARRAY_SIZE(spitz_gpio_keys),
+static struct gpio_keys_platform_data sharpslc_gpio_keys_platform_data = {
+ .buttons = sharpslc_gpio_keys,
+ .nbuttons = ARRAY_SIZE(sharpslc_gpio_keys),
};
-static struct platform_device spitz_gpio_keys_device = {
+static struct platform_device sharpslc_gpio_keys_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
- .platform_data = &spitz_gpio_keys_platform_data,
+ .platform_data = &sharpslc_gpio_keys_platform_data,
},
};
+static void __init sharpslc_keys_init(void)
+{
+ platform_device_register(&sharpslc_gpio_keys_device);
+}
+#else
+static inline void sharpslc_keys_init(void) {}
+#endif
-/*
- * Spitz LEDs
- */
-static struct gpio_led spitz_gpio_leds[] = {
+/******************************************************************************
+ * LEDs
+ ******************************************************************************/
+#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpio_led sharpslc_gpio_leds[] = {
{
.name = "spitz:amber:charge",
- .default_trigger = "sharpsl-charge",
+ .default_trigger = "sharpslc-charge",
.gpio = SPITZ_GPIO_LED_ORANGE,
},
{
@@ -413,25 +465,32 @@ static struct gpio_led spitz_gpio_leds[] = {
},
};
-static struct gpio_led_platform_data spitz_gpio_leds_info = {
- .leds = spitz_gpio_leds,
- .num_leds = ARRAY_SIZE(spitz_gpio_leds),
+static struct gpio_led_platform_data sharpslc_gpio_leds_info = {
+ .leds = sharpslc_gpio_leds,
+ .num_leds = ARRAY_SIZE(sharpslc_gpio_leds),
};
-static struct platform_device spitzled_device = {
+static struct platform_device sharpslc_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
- .platform_data = &spitz_gpio_leds_info,
+ .platform_data = &sharpslc_gpio_leds_info,
},
};
-#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static struct pxa2xx_spi_master spitz_spi_info = {
- .num_chipselect = 3,
-};
+static void __init sharpslc_leds_init(void)
+{
+ platform_device_register(&sharpslc_led_device);
+}
+#else
+static inline void sharpslc_leds_init(void) {}
+#endif
-static void spitz_wait_for_hsync(void)
+/******************************************************************************
+ * SSP Devices
+ ******************************************************************************/
+#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
+static void sharpslc_ads7846_wait_for_hsync(void)
{
while (gpio_get_value(SPITZ_GPIO_HSYNC))
cpu_relax();
@@ -440,21 +499,21 @@ static void spitz_wait_for_hsync(void)
cpu_relax();
}
-static struct ads7846_platform_data spitz_ads7846_info = {
+static struct ads7846_platform_data sharpslc_ads7846_info = {
.model = 7846,
.vref_delay_usecs = 100,
.x_plate_ohms = 419,
.y_plate_ohms = 486,
.pressure_max = 1024,
.gpio_pendown = SPITZ_GPIO_TP_INT,
- .wait_for_sync = spitz_wait_for_hsync,
+ .wait_for_sync = sharpslc_ads7846_wait_for_hsync,
};
-static struct pxa2xx_spi_chip spitz_ads7846_chip = {
+static struct pxa2xx_spi_chip sharpslc_ads7846_chip = {
.gpio_cs = SPITZ_GPIO_ADS7846_CS,
};
-static void spitz_bl_kick_battery(void)
+static void sharpslc_bl_kick_battery(void)
{
void (*kick_batt)(void);
@@ -465,93 +524,109 @@ static void spitz_bl_kick_battery(void)
}
}
-static struct corgi_lcd_platform_data spitz_lcdcon_info = {
+static struct corgi_lcd_platform_data sharpslc_lcdcon_info = {
.init_mode = CORGI_LCD_MODE_VGA,
.max_intensity = 0x2f,
.default_intensity = 0x1f,
.limit_mask = 0x0b,
.gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT,
.gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON,
- .kick_battery = spitz_bl_kick_battery,
+ .kick_battery = sharpslc_bl_kick_battery,
};
-static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
+static struct pxa2xx_spi_chip sharpslc_lcdcon_chip = {
.gpio_cs = SPITZ_GPIO_LCDCON_CS,
};
-static struct pxa2xx_spi_chip spitz_max1111_chip = {
+static struct pxa2xx_spi_chip sharpslc_max1111_chip = {
.gpio_cs = SPITZ_GPIO_MAX1111_CS,
};
-static struct spi_board_info spitz_spi_devices[] = {
+static struct spi_board_info sharpslc_spi_devices[] = {
{
- .modalias = "ads7846",
- .max_speed_hz = 1200000,
- .bus_num = 2,
- .chip_select = 0,
- .platform_data = &spitz_ads7846_info,
- .controller_data= &spitz_ads7846_chip,
- .irq = gpio_to_irq(SPITZ_GPIO_TP_INT),
+ .modalias = "ads7846",
+ .max_speed_hz = 1200000,
+ .bus_num = 2,
+ .chip_select = 0,
+ .platform_data = &sharpslc_ads7846_info,
+ .controller_data = &sharpslc_ads7846_chip,
+ .irq = gpio_to_irq(SPITZ_GPIO_TP_INT),
}, {
- .modalias = "corgi-lcd",
- .max_speed_hz = 50000,
- .bus_num = 2,
- .chip_select = 1,
- .platform_data = &spitz_lcdcon_info,
- .controller_data= &spitz_lcdcon_chip,
+ .modalias = "corgi-lcd",
+ .max_speed_hz = 50000,
+ .bus_num = 2,
+ .chip_select = 1,
+ .platform_data = &sharpslc_lcdcon_info,
+ .controller_data = &sharpslc_lcdcon_chip,
}, {
- .modalias = "max1111",
- .max_speed_hz = 450000,
- .bus_num = 2,
- .chip_select = 2,
- .controller_data= &spitz_max1111_chip,
+ .modalias = "max1111",
+ .max_speed_hz = 450000,
+ .bus_num = 2,
+ .chip_select = 2,
+ .controller_data = &sharpslc_max1111_chip,
},
};
-static void __init spitz_init_spi(void)
+static struct pxa2xx_spi_master sharpslc_spi_info = {
+ .num_chipselect = 3,
+};
+
+static void __init sharpslc_spi_init(void)
{
+ struct corgi_lcd_platform_data *lcd_data = &sharpslc_lcdcon_info;
+
if (machine_is_akita()) {
- spitz_lcdcon_info.gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT;
- spitz_lcdcon_info.gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON;
+ lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT;
+ lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON;
}
- pxa2xx_set_spi_info(2, &spitz_spi_info);
- spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
+ pxa2xx_set_spi_info(2, &sharpslc_spi_info);
+ spi_register_board_info(ARRAY_AND_SIZE(sharpslc_spi_devices));
}
#else
-static inline void spitz_init_spi(void) {}
+static inline void sharpslc_spi_init(void) {}
#endif
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
/*
- * MMC/SD Device
- *
- * The card detect interrupt isn't debounced so we delay it by 250ms
- * to give the card a chance to fully insert/eject.
+ * NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to
+ * give the card a chance to fully insert/eject.
*/
-static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
+static void sharpslc_mci_setpower(struct device *dev, unsigned int vdd)
{
struct pxamci_platform_data* p_d = dev->platform_data;
- if (( 1 << vdd) & p_d->ocr_mask)
- spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0004);
+ if ((1 << vdd) & p_d->ocr_mask)
+ sharpslc_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V);
else
- spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
+ sharpslc_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0);
}
-static struct pxamci_platform_data spitz_mci_platform_data = {
+static struct pxamci_platform_data sharpslc_mci_platform_data = {
.detect_delay_ms = 250,
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .setpower = spitz_mci_setpower,
+ .setpower = sharpslc_mci_setpower,
.gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
.gpio_card_ro = SPITZ_GPIO_nSD_WP,
.gpio_power = -1,
};
+static void __init sharpslc_mmc_init(void)
+{
+ pxa_set_mci_info(&sharpslc_mci_platform_data);
+}
+#else
+static inline void sharpslc_mmc_init(void) {}
+#endif
-/*
- * USB Host (OHCI)
- */
-static int spitz_ohci_init(struct device *dev)
+/******************************************************************************
+ * USB Host
+ ******************************************************************************/
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+static int sharpslc_ohci_init(struct device *dev)
{
int err;
@@ -559,88 +634,114 @@ static int spitz_ohci_init(struct device *dev)
if (err)
return err;
- /* Only Port 2 is connected
- * Setup USB Port 2 Output Control Register
- */
+ /* Only Port 2 is connected, setup USB Port 2 Output Control Register */
UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
}
-static void spitz_ohci_exit(struct device *dev)
+static void sharpslc_ohci_exit(struct device *dev)
{
gpio_free(SPITZ_GPIO_USB_HOST);
}
-static struct pxaohci_platform_data spitz_ohci_platform_data = {
+static struct pxaohci_platform_data sharpslc_ohci_platform_data = {
.port_mode = PMM_NPS_MODE,
- .init = spitz_ohci_init,
- .exit = spitz_ohci_exit,
+ .init = sharpslc_ohci_init,
+ .exit = sharpslc_ohci_exit,
.flags = ENABLE_PORT_ALL | NO_OC_PROTECTION,
.power_budget = 150,
};
+static void __init sharpslc_uhc_init(void)
+{
+ pxa_set_ohci_info(&sharpslc_ohci_platform_data);
+}
+#else
+static inline void sharpslc_uhc_init(void) {}
+#endif
-/*
- * Irda
- */
-
-static struct pxaficp_platform_data spitz_ficp_platform_data = {
-/* .gpio_pwdown is set in spitz_init() and akita_init() accordingly */
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+#if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE)
+static struct pxaficp_platform_data sharpslc_ficp_platform_data = {
.transceiver_cap = IR_SIRMODE | IR_OFF,
};
+static void __init sharpslc_irda_init(void)
+{
+ if (machine_is_akita())
+ sharpslc_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
+ else
+ sharpslc_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
-/*
- * Spitz PXA Framebuffer
- */
+ pxa_set_ficp_info(&sharpslc_ficp_platform_data);
+}
+#else
+static inline void sharpslc_irda_init(void) {}
+#endif
-static struct pxafb_mode_info spitz_pxafb_modes[] = {
-{
- .pixclock = 19231,
- .xres = 480,
- .yres = 640,
- .bpp = 16,
- .hsync_len = 40,
- .left_margin = 46,
- .right_margin = 125,
- .vsync_len = 3,
- .upper_margin = 1,
- .lower_margin = 0,
- .sync = 0,
-},{
- .pixclock = 134617,
- .xres = 240,
- .yres = 320,
- .bpp = 16,
- .hsync_len = 20,
- .left_margin = 20,
- .right_margin = 46,
- .vsync_len = 2,
- .upper_margin = 1,
- .lower_margin = 0,
- .sync = 0,
-},
-};
-
-static struct pxafb_mach_info spitz_pxafb_info = {
- .modes = &spitz_pxafb_modes[0],
- .num_modes = 2,
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
+static struct pxafb_mode_info sharpslc_pxafb_modes[] = {
+ {
+ .pixclock = 19231,
+ .xres = 480,
+ .yres = 640,
+ .bpp = 16,
+ .hsync_len = 40,
+ .left_margin = 46,
+ .right_margin = 125,
+ .vsync_len = 3,
+ .upper_margin = 1,
+ .lower_margin = 0,
+ .sync = 0,
+ }, {
+ .pixclock = 134617,
+ .xres = 240,
+ .yres = 320,
+ .bpp = 16,
+ .hsync_len = 20,
+ .left_margin = 20,
+ .right_margin = 46,
+ .vsync_len = 2,
+ .upper_margin = 1,
+ .lower_margin = 0,
+ .sync = 0,
+ },
+};
+
+static struct pxafb_mach_info sharpslc_pxafb_info = {
+ .modes = sharpslc_pxafb_modes,
+ .num_modes = ARRAY_SIZE(sharpslc_pxafb_modes),
.fixed_modes = 1,
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING,
};
-static struct mtd_partition sharpsl_nand_partitions[] = {
+static void __init sharpslc_lcd_init(void)
+{
+ set_pxa_fb_info(&sharpslc_pxafb_info);
+}
+#else
+static inline void sharpslc_lcd_init(void) {}
+#endif
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+#if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE)
+static struct mtd_partition sharpslc_nand_partitions[] = {
{
.name = "System Area",
.offset = 0,
.size = 7 * 1024 * 1024,
- },
- {
+ }, {
.name = "Root Filesystem",
.offset = 7 * 1024 * 1024,
- },
- {
+ }, {
.name = "Home Filesystem",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
@@ -649,37 +750,72 @@ static struct mtd_partition sharpsl_nand_partitions[] = {
static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
-static struct nand_bbt_descr sharpsl_bbt = {
- .options = 0,
- .offs = 4,
- .len = 2,
- .pattern = scan_ff_pattern
+static struct nand_bbt_descr sharpslc_nand_bbt = {
+ .options = 0,
+ .offs = 4,
+ .len = 2,
+ .pattern = scan_ff_pattern
+};
+
+static struct nand_ecclayout sharpslc_akita_oobinfo = {
+ .oobfree = { {0x08, 0x09} },
+ .eccbytes = 24,
+ .eccpos = {
+ 0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11,
+ 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
+ 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37,
+ },
};
-static struct sharpsl_nand_platform_data sharpsl_nand_platform_data = {
- .badblock_pattern = &sharpsl_bbt,
- .partitions = sharpsl_nand_partitions,
- .nr_partitions = ARRAY_SIZE(sharpsl_nand_partitions),
+static struct sharpsl_nand_platform_data sharpslc_nand_pdata = {
+ .badblock_pattern = &sharpslc_nand_bbt,
+ .partitions = sharpslc_nand_partitions,
+ .nr_partitions = ARRAY_SIZE(sharpslc_nand_partitions),
};
-static struct resource sharpsl_nand_resources[] = {
+static struct resource sharpslc_nand_resources[] = {
{
- .start = 0x0C000000,
- .end = 0x0C000FFF,
+ .start = PXA_CS3_PHYS,
+ .end = PXA_CS3_PHYS + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
-static struct platform_device sharpsl_nand_device = {
+static struct platform_device sharpslc_nand_device = {
.name = "sharpsl-nand",
.id = -1,
- .resource = sharpsl_nand_resources,
- .num_resources = ARRAY_SIZE(sharpsl_nand_resources),
- .dev.platform_data = &sharpsl_nand_platform_data,
+ .resource = sharpslc_nand_resources,
+ .num_resources = ARRAY_SIZE(sharpslc_nand_resources),
+ .dev = {
+ .platform_data = &sharpslc_nand_pdata,
+ }
};
+static void __init sharpslc_nand_init(void)
+{
+ if (machine_is_spitz()) {
+ sharpslc_nand_partitions[1].size = 5 * 1024 * 1024;
+ } else if (machine_is_akita()) {
+ sharpslc_nand_partitions[1].size = 58 * 1024 * 1024;
+ sharpslc_nand_bbt.len = 1;
+ sharpslc_nand_pdata.ecc_layout = &sharpslc_akita_oobinfo;
+ } else if (machine_is_borzoi()) {
+ sharpslc_nand_partitions[1].size = 32 * 1024 * 1024;
+ sharpslc_nand_bbt.len = 1;
+ sharpslc_nand_pdata.ecc_layout = &sharpslc_akita_oobinfo;
+ }
+
+ platform_device_register(&sharpslc_nand_device);
+}
+#else
+static inline void sharpslc_nand_init(void) {}
+#endif
-static struct mtd_partition sharpsl_rom_parts[] = {
+/******************************************************************************
+ * NOR Flash
+ ******************************************************************************/
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition sharpslc_rom_parts[] = {
{
.name ="Boot PROM Filesystem",
.offset = 0x00140000,
@@ -687,161 +823,152 @@ static struct mtd_partition sharpsl_rom_parts[] = {
},
};
-static struct physmap_flash_data sharpsl_rom_data = {
+static struct physmap_flash_data sharpslc_rom_data = {
.width = 2,
- .nr_parts = ARRAY_SIZE(sharpsl_rom_parts),
- .parts = sharpsl_rom_parts,
+ .nr_parts = ARRAY_SIZE(sharpslc_rom_parts),
+ .parts = sharpslc_rom_parts,
};
-static struct resource sharpsl_rom_resources[] = {
+static struct resource sharpslc_rom_resources[] = {
{
- .start = 0x00000000,
- .end = 0x007fffff,
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
},
};
-static struct platform_device sharpsl_rom_device = {
- .name = "physmap-flash",
- .id = -1,
- .resource = sharpsl_rom_resources,
- .num_resources = ARRAY_SIZE(sharpsl_rom_resources),
- .dev.platform_data = &sharpsl_rom_data,
-};
-
-static struct platform_device *devices[] __initdata = {
- &spitzscoop_device,
- &spitzkbd_device,
- &spitz_gpio_keys_device,
- &spitzled_device,
- &sharpsl_nand_device,
- &sharpsl_rom_device,
+static struct platform_device sharpslc_rom_device = {
+ .name = "physmap-flash",
+ .id = -1,
+ .resource = sharpslc_rom_resources,
+ .num_resources = ARRAY_SIZE(sharpslc_rom_resources),
+ .dev = {
+ .platform_data = &sharpslc_rom_data,
+ },
};
-static void spitz_poweroff(void)
+static void __init sharpslc_nor_init(void)
{
- arm_machine_restart('g', NULL);
+ platform_device_register(&sharpslc_rom_device);
}
+#else
+static inline void sharpslc_nor_init(void) {}
+#endif
-static void spitz_restart(char mode, const char *cmd)
-{
- /* Bootloader magic for a reboot */
- if((MSC0 & 0xffff0000) == 0x7ff00000)
- MSC0 = (MSC0 & 0xffff) | 0x7ee00000;
-
- spitz_poweroff();
-}
+/******************************************************************************
+ * GPIO expander
+ ******************************************************************************/
+#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
+static struct pca953x_platform_data akita_pca953x_pdata = {
+ .gpio_base = AKITA_IOEXP_GPIO_BASE,
+};
-static void __init common_init(void)
-{
- init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
- pm_power_off = spitz_poweroff;
- arm_pm_restart = spitz_restart;
+static struct i2c_board_info sharpslc_i2c_devs[] = {
+ {
+ .type = "wm8750",
+ .addr = 0x1b,
+ }, {
+ .type = "max7310",
+ .addr = 0x18,
+ .platform_data = &akita_pca953x_pdata,
+ },
+};
- if (machine_is_spitz()) {
- sharpsl_nand_partitions[1].size = 5 * 1024 * 1024;
- } else if (machine_is_akita()) {
- sharpsl_nand_partitions[1].size = 58 * 1024 * 1024;
- } else if (machine_is_borzoi()) {
- sharpsl_nand_partitions[1].size = 32 * 1024 * 1024;
+static struct regulator_consumer_supply isl6271a_consumers[] = {
+ {
+ .supply = "vcc_core",
}
+};
- PMCR = 0x00;
-
- /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
- PCFR |= PCFR_OPDE;
+static struct regulator_init_data isl6271a_info[] = {
+ {
+ .constraints = {
+ .name = "vcc_core range",
+ .min_uV = 850000,
+ .max_uV = 1600000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .consumer_supplies = isl6271a_consumers,
+ .num_consumer_supplies = ARRAY_SIZE(isl6271a_consumers),
+ }
+};
- pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
+static struct i2c_board_info sharpslc_pi2c_devs[] = {
+ {
+ .type = "isl6271a",
+ .addr = 0x0c,
+ .platform_data = &isl6271a_info,
+ },
+};
- pxa_set_ffuart_info(NULL);
- pxa_set_btuart_info(NULL);
- pxa_set_stuart_info(NULL);
+static void __init sharpslc_i2c_init(void)
+{
+ int size = ARRAY_SIZE(sharpslc_i2c_devs);
- spitz_init_spi();
+ /* Only Akita has the max7310 chip */
+ if (!machine_is_akita())
+ size--;
- platform_add_devices(devices, ARRAY_SIZE(devices));
- pxa_set_mci_info(&spitz_mci_platform_data);
- pxa_set_ohci_info(&spitz_ohci_platform_data);
- pxa_set_ficp_info(&spitz_ficp_platform_data);
- set_pxa_fb_info(&spitz_pxafb_info);
pxa_set_i2c_info(NULL);
+ pxa27x_set_i2c_power_info(NULL);
+ i2c_register_board_info(0, sharpslc_i2c_devs, size);
+ i2c_register_board_info(1, ARRAY_AND_SIZE(sharpslc_pi2c_devs));
}
-
-#if defined(CONFIG_MACH_AKITA) || defined(CONFIG_MACH_BORZOI)
-static struct nand_bbt_descr sharpsl_akita_bbt = {
- .options = 0,
- .offs = 4,
- .len = 1,
- .pattern = scan_ff_pattern
-};
-
-static struct nand_ecclayout akita_oobinfo = {
- .eccbytes = 24,
- .eccpos = {
- 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11,
- 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
- 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37},
- .oobfree = {{0x08, 0x09}}
-};
+#else
+static inline void sharpslc_i2c_init(void) {}
#endif
-#if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
-static void __init spitz_init(void)
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static void sharpslc_poweroff(void)
{
- spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
-
-#ifdef CONFIG_MACH_BORZOI
- if (machine_is_borzoi()) {
- sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
- sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
- }
-#endif
-
- platform_scoop_config = &spitz_pcmcia_config;
-
- common_init();
-
- platform_device_register(&spitzscoop2_device);
+ arm_machine_restart('g', NULL);
}
-#endif
-#ifdef CONFIG_MACH_AKITA
-/*
- * Akita IO Expander
- */
-static struct pca953x_platform_data akita_ioexp = {
- .gpio_base = AKITA_IOEXP_GPIO_BASE,
-};
+static void sharpslc_restart(char mode, const char *cmd)
+{
+ /* Bootloader magic for a reboot */
+ if ((MSC0 & 0xffff0000) == 0x7ff00000)
+ MSC0 = (MSC0 & 0xffff) | 0x7ee00000;
-static struct i2c_board_info akita_i2c_board_info[] = {
- {
- .type = "max7310",
- .addr = 0x18,
- .platform_data = &akita_ioexp,
- }, {
- .type = "wm8750",
- .addr = 0x1b,
- },
-};
+ sharpslc_poweroff();
+}
-static void __init akita_init(void)
+static void __init sharpslc_init(void)
{
- spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
+ init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
+ pm_power_off = sharpslc_poweroff;
+ arm_pm_restart = sharpslc_restart;
+
+ PMCR = 0x00;
- sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
- sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
+ /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
+ PCFR |= PCFR_OPDE;
- /* We just pretend the second element of the array doesn't exist */
- spitz_pcmcia_config.num_devs = 1;
- platform_scoop_config = &spitz_pcmcia_config;
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(sharpslc_pin_config));
- i2c_register_board_info(0, ARRAY_AND_SIZE(akita_i2c_board_info));
+ pxa_set_ffuart_info(NULL);
+ pxa_set_btuart_info(NULL);
+ pxa_set_stuart_info(NULL);
- common_init();
+ sharpslc_spi_init();
+ sharpslc_scoop_init();
+ sharpslc_mkp_init();
+ sharpslc_keys_init();
+ sharpslc_leds_init();
+ sharpslc_mmc_init();
+ sharpslc_pcmcia_init();
+ sharpslc_irda_init();
+ sharpslc_uhc_init();
+ sharpslc_lcd_init();
+ sharpslc_nor_init();
+ sharpslc_nand_init();
+ sharpslc_i2c_init();
}
-#endif
-static void __init fixup_spitz(struct machine_desc *desc,
+static void __init sharpslc_fixup(struct machine_desc *desc,
struct tag *tags, char **cmdline, struct meminfo *mi)
{
sharpsl_save_param();
@@ -855,10 +982,10 @@ static void __init fixup_spitz(struct machine_desc *desc,
MACHINE_START(SPITZ, "SHARP Spitz")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = fixup_spitz,
+ .fixup = sharpslc_fixup,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
- .init_machine = spitz_init,
+ .init_machine = sharpslc_init,
.timer = &pxa_timer,
MACHINE_END
#endif
@@ -867,10 +994,10 @@ MACHINE_END
MACHINE_START(BORZOI, "SHARP Borzoi")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = fixup_spitz,
+ .fixup = sharpslc_fixup,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
- .init_machine = spitz_init,
+ .init_machine = sharpslc_init,
.timer = &pxa_timer,
MACHINE_END
#endif
@@ -879,10 +1006,10 @@ MACHINE_END
MACHINE_START(AKITA, "SHARP Akita")
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
- .fixup = fixup_spitz,
+ .fixup = sharpslc_fixup,
.map_io = pxa_map_io,
.init_irq = pxa27x_init_irq,
- .init_machine = akita_init,
+ .init_machine = sharpslc_init,
.timer = &pxa_timer,
MACHINE_END
#endif
--
1.7.1
More information about the linux-arm-kernel
mailing list