[PATCH 1/2] ASoC: Add SmartQ sound driver
Maurus Cuelenaere
mcuelenaere at gmail.com
Fri Jul 2 20:13:46 EDT 2010
This adds sound support for the SmartQ board.
The hardware consists of a S3C6410 coupled with a WM8987 over I²S. As there's
no driver for the WM8987 currently, this uses the WM8750 driver (which should
be register compatible).
Signed-off-by: Maurus Cuelenaere <mcuelenaere at gmail.com>
---
sound/soc/s3c24xx/Kconfig | 6 +
sound/soc/s3c24xx/Makefile | 2 +
sound/soc/s3c24xx/smartq_wm8987.c | 300 +++++++++++++++++++++++++++++++++++++
3 files changed, 308 insertions(+), 0 deletions(-)
create mode 100644 sound/soc/s3c24xx/smartq_wm8987.c
diff --git a/sound/soc/s3c24xx/Kconfig b/sound/soc/s3c24xx/Kconfig
index 2a7cc22..4f46ba0 100644
--- a/sound/soc/s3c24xx/Kconfig
+++ b/sound/soc/s3c24xx/Kconfig
@@ -125,3 +125,9 @@ config SND_SOC_SMDK_WM9713
select SND_S3C_SOC_AC97
help
Sat Y if you want to add support for SoC audio on the SMDK.
+
+config SND_S3C64XX_SOC_SMARTQ
+ tristate "SoC I2S Audio support for SmartQ board"
+ depends on SND_S3C24XX_SOC && MACH_SMARTQ
+ select SND_S3C64XX_SOC_I2S
+ select SND_SOC_WM8750
diff --git a/sound/soc/s3c24xx/Makefile b/sound/soc/s3c24xx/Makefile
index 81d8dc5..50172c3 100644
--- a/sound/soc/s3c24xx/Makefile
+++ b/sound/soc/s3c24xx/Makefile
@@ -29,6 +29,7 @@ snd-soc-s3c24xx-simtec-hermes-objs := s3c24xx_simtec_hermes.o
snd-soc-s3c24xx-simtec-tlv320aic23-objs := s3c24xx_simtec_tlv320aic23.o
snd-soc-smdk64xx-wm8580-objs := smdk64xx_wm8580.o
snd-soc-smdk-wm9713-objs := smdk_wm9713.o
+snd-soc-s3c64xx-smartq-wm8987-objs := smartq_wm8987.o
obj-$(CONFIG_SND_S3C24XX_SOC_JIVE_WM8750) += snd-soc-jive-wm8750.o
obj-$(CONFIG_SND_S3C24XX_SOC_NEO1973_WM8753) += snd-soc-neo1973-wm8753.o
@@ -41,3 +42,4 @@ obj-$(CONFIG_SND_S3C24XX_SOC_SIMTEC_HERMES) += snd-soc-s3c24xx-simtec-hermes.o
obj-$(CONFIG_SND_S3C24XX_SOC_SIMTEC_TLV320AIC23) += snd-soc-s3c24xx-simtec-tlv320aic23.o
obj-$(CONFIG_SND_S3C64XX_SOC_WM8580) += snd-soc-smdk64xx-wm8580.o
obj-$(CONFIG_SND_SOC_SMDK_WM9713) += snd-soc-smdk-wm9713.o
+obj-$(CONFIG_SND_S3C64XX_SOC_SMARTQ) += snd-soc-s3c64xx-smartq-wm8987.o
diff --git a/sound/soc/s3c24xx/smartq_wm8987.c b/sound/soc/s3c24xx/smartq_wm8987.c
new file mode 100644
index 0000000..ef6183f
--- /dev/null
+++ b/sound/soc/s3c24xx/smartq_wm8987.c
@@ -0,0 +1,300 @@
+/* sound/soc/s3c24xx/smartq_wm8987.c
+ *
+ * Copyright 2010 Maurus Cuelenaere <mcuelenaere at gmail.com>
+ *
+ * Based on smdk6410_wm8987.c
+ * Copyright 2007 Wolfson Microelectronics PLC. - linux at wolfsonmicro.com
+ * Graeme Gregory - graeme.gregory at wolfsonmicro.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc-dapm.h>
+#include <sound/jack.h>
+
+#include <asm/mach-types.h>
+
+#include "s3c-dma.h"
+#include "s3c64xx-i2s.h"
+
+#include "../codecs/wm8750.h"
+
+/*
+ * According to http://www.wolfsonmicro.com/products/WM8987 the WM8987 is
+ * register compatible with the WM8750, so I'm currently using that one as
+ * there's no WM8987 codec driver.
+ */
+
+static struct snd_soc_card snd_soc_smartq;
+
+static int smartq_hifi_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct snd_soc_dai *codec_dai = rtd->dai->codec_dai;
+ struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
+ struct s3c_i2sv2_rate_calc div;
+ unsigned int clk = 0;
+ int ret;
+
+ s3c_i2sv2_iis_calc_rate(&div, NULL, params_rate(params),
+ s3c_i2sv2_get_clock(cpu_dai));
+
+ switch (params_rate(params)) {
+ case 8000:
+ case 16000:
+ case 32000:
+ case 48000:
+ case 96000:
+ clk = 12288000;
+ break;
+ case 11025:
+ case 22050:
+ case 44100:
+ case 88200:
+ clk = 11289600;
+ break;
+ }
+
+ /* set codec DAI configuration */
+ ret = snd_soc_dai_set_fmt(codec_dai, SND_SOC_DAIFMT_I2S |
+ SND_SOC_DAIFMT_NB_NF |
+ SND_SOC_DAIFMT_CBS_CFS);
+ if (ret < 0)
+ return ret;
+
+ /* set cpu DAI configuration */
+ ret = snd_soc_dai_set_fmt(cpu_dai, SND_SOC_DAIFMT_I2S |
+ SND_SOC_DAIFMT_NB_NF |
+ SND_SOC_DAIFMT_CBS_CFS);
+ if (ret < 0)
+ return ret;
+
+ /* set the codec system clock for DAC and ADC */
+ ret = snd_soc_dai_set_sysclk(codec_dai, WM8750_SYSCLK, clk,
+ SND_SOC_CLOCK_IN);
+ if (ret < 0)
+ return ret;
+
+ /* set MCLK division for sample rate */
+ ret = snd_soc_dai_set_clkdiv(cpu_dai, S3C_I2SV2_DIV_RCLK, div.fs_div);
+ if (ret < 0)
+ return ret;
+
+ /* set prescaler division for sample rate */
+ ret = snd_soc_dai_set_clkdiv(cpu_dai, S3C_I2SV2_DIV_PRESCALER,
+ div.clk_div - 1);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+/*
+ * SmartQ WM8987 HiFi DAI operations.
+ */
+static struct snd_soc_ops smartq_hifi_ops = {
+ .hw_params = smartq_hifi_hw_params,
+};
+
+static struct snd_soc_jack smartq_jack;
+
+static struct snd_soc_jack_pin smartq_jack_pins[] = {
+ /* Disable speaker when headphone is plugged in */
+ {
+ .pin = "Internal Speaker",
+ .mask = SND_JACK_HEADPHONE,
+ .invert = true,
+ },
+};
+
+static struct snd_soc_jack_gpio smartq_jack_gpios[] = {
+ {
+ .gpio = S3C64XX_GPL(12),
+ .name = "headphone detect",
+ .report = SND_JACK_HEADPHONE,
+ .debounce_time = 200,
+ },
+};
+
+static const struct snd_kcontrol_new wm8987_smartq_controls[] = {
+ SOC_DAPM_PIN_SWITCH("Internal Speaker"),
+ SOC_DAPM_PIN_SWITCH("Headphone Jack"),
+ SOC_DAPM_PIN_SWITCH("Internal Mic"),
+};
+
+static int smartq_speaker_event(struct snd_soc_dapm_widget *w,
+ struct snd_kcontrol *k,
+ int event)
+{
+ gpio_set_value(S3C64XX_GPK(12), SND_SOC_DAPM_EVENT_OFF(event));
+
+ return 0;
+}
+
+static const struct snd_soc_dapm_widget wm8987_dapm_widgets[] = {
+ SND_SOC_DAPM_SPK("Internal Speaker", smartq_speaker_event),
+ SND_SOC_DAPM_HP("Headphone Jack", NULL),
+ SND_SOC_DAPM_MIC("Internal Mic", NULL),
+};
+
+static const struct snd_soc_dapm_route audio_map[] = {
+ {"Headphone Jack", NULL, "LOUT2"},
+ {"Headphone Jack", NULL, "ROUT2"},
+
+ {"Internal Speaker", NULL, "LOUT2"},
+ {"Internal Speaker", NULL, "ROUT2"},
+
+ {"Mic Bias", NULL, "Internal Mic"},
+ {"LINPUT2", NULL, "Mic Bias"},
+};
+
+static int smartq_wm8987_init(struct snd_soc_codec *codec)
+{
+ int err = 0;
+
+ /* Add SmartQ specific widgets */
+ snd_soc_dapm_new_controls(codec, wm8987_dapm_widgets,
+ ARRAY_SIZE(wm8987_dapm_widgets));
+
+ /* add SmartQ specific controls */
+ err = snd_soc_add_controls(codec, wm8987_smartq_controls,
+ ARRAY_SIZE(wm8987_smartq_controls));
+
+ if (err < 0)
+ return err;
+
+ /* setup SmartQ specific audio path */
+ snd_soc_dapm_add_routes(codec, audio_map, ARRAY_SIZE(audio_map));
+
+ /* set endpoints to not connected */
+ snd_soc_dapm_nc_pin(codec, "LINPUT1");
+ snd_soc_dapm_nc_pin(codec, "RINPUT1");
+ snd_soc_dapm_nc_pin(codec, "OUT3");
+ snd_soc_dapm_nc_pin(codec, "ROUT1");
+
+ /* set endpoints to default off mode */
+ snd_soc_dapm_enable_pin(codec, "Internal Speaker");
+ snd_soc_dapm_enable_pin(codec, "Internal Mic");
+ snd_soc_dapm_disable_pin(codec, "Headphone Jack");
+
+ err = snd_soc_dapm_sync(codec);
+ if (err)
+ return err;
+
+ /* Headphone jack detection */
+ err = snd_soc_jack_new(&snd_soc_smartq, "Headphone Jack",
+ SND_JACK_HEADPHONE, &smartq_jack);
+ if (err)
+ return err;
+
+ err = snd_soc_jack_add_pins(&smartq_jack, ARRAY_SIZE(smartq_jack_pins),
+ smartq_jack_pins);
+ if (err)
+ return err;
+
+ err = snd_soc_jack_add_gpios(&smartq_jack,
+ ARRAY_SIZE(smartq_jack_gpios),
+ smartq_jack_gpios);
+
+ return err;
+}
+
+static struct snd_soc_dai_link smartq_dai[] = {
+ {
+ .name = "wm8987",
+ .stream_name = "SmartQ Hi-Fi",
+ .cpu_dai = &s3c64xx_i2s_dai[0],
+ .codec_dai = &wm8750_dai,
+ .init = smartq_wm8987_init,
+ .ops = &smartq_hifi_ops,
+ },
+};
+
+static struct snd_soc_card snd_soc_smartq = {
+ .name = "SmartQ",
+ .platform = &s3c24xx_soc_platform,
+ .dai_link = smartq_dai,
+ .num_links = ARRAY_SIZE(smartq_dai),
+};
+
+static struct snd_soc_device smartq_snd_devdata = {
+ .card = &snd_soc_smartq,
+ .codec_dev = &soc_codec_dev_wm8750,
+};
+
+static struct platform_device *smartq_snd_device;
+
+static int __init smartq_init(void)
+{
+ int ret;
+
+ if (!machine_is_smartq7() && !machine_is_smartq5()) {
+ pr_info("Only SmartQ is supported by this ASoC driver\n");
+ return -ENODEV;
+ }
+
+ smartq_snd_device = platform_device_alloc("soc-audio", -1);
+ if (!smartq_snd_device)
+ return -ENOMEM;
+
+ platform_set_drvdata(smartq_snd_device, &smartq_snd_devdata);
+ smartq_snd_devdata.dev = &smartq_snd_device->dev;
+
+ ret = platform_device_add(smartq_snd_device);
+ if (ret) {
+ platform_device_put(smartq_snd_device);
+ return ret;
+ }
+
+ /* Initialise GPIOs used by amplifiers */
+ ret = gpio_request(S3C64XX_GPK(12), "amplifiers shutdown");
+ if (ret) {
+ dev_err(&smartq_snd_device->dev, "Failed to register GPK12\n");
+ goto err_unregister_device;
+ }
+
+ /* Disable amplifiers */
+ ret = gpio_direction_output(S3C64XX_GPK(12), 1);
+ if (ret) {
+ dev_err(&smartq_snd_device->dev, "Failed to configure GPK12\n");
+ goto err_free_gpio_amp_shut;
+ }
+
+ dev_info(&smartq_snd_device->dev, "SmartQ WM8987 audio driver inited\n");
+
+ return 0;
+
+err_free_gpio_amp_shut:
+ gpio_free(S3C64XX_GPK(12));
+err_unregister_device:
+ platform_device_unregister(smartq_snd_device);
+
+ return ret;
+}
+
+static void __exit smartq_exit(void)
+{
+ snd_soc_jack_free_gpios(&smartq_jack, ARRAY_SIZE(smartq_jack_gpios),
+ smartq_jack_gpios);
+
+ platform_device_unregister(smartq_snd_device);
+}
+
+module_init(smartq_init);
+module_exit(smartq_exit);
+
+/* Module information */
+MODULE_AUTHOR("Maurus Cuelenaere");
+MODULE_DESCRIPTION("ALSA SoC SmartQ WM8987");
+MODULE_LICENSE("GPL");
--
1.7.0.4
More information about the linux-arm-kernel
mailing list