[PATCH v2] OpenRD: Enable SD/UART selection for serial port 1

[Alexander Clouter]

Hi,

Comments inline.

* Tanmay Upadhyay <tanmay.upadhyay at einfochips.com> [2010-08-10 13:59:33+0530]:
>
> This patch enables user to use serial port 1 of the OpenRD device for SDIO
> or UART(RS232/RS485). The selection can be done through kernel parameter.
> 
> By default the port would be used for SDIO. To select RS232 or RS485 mode,
> pass string "uart=232" or "uart=485" respectively in the kernel parameters.
> "uart=485" is ignored on OpenRD-Base as it doesn't have RS485 port.
> 
> Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay at einfochips.com>
> ---
>  arch/arm/mach-kirkwood/openrd-setup.c |   92 ++++++++++++++++++++++++++++++++-
>  1 files changed, 91 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/mach-kirkwood/openrd-setup.c b/arch/arm/mach-kirkwood/openrd-setup.c
> index fd06be6..cd061ab 100644
> --- a/arch/arm/mach-kirkwood/openrd-setup.c
> +++ b/arch/arm/mach-kirkwood/openrd-setup.c
> @@ -19,6 +19,7 @@
>  #include <asm/mach-types.h>
>  #include <asm/mach/arch.h>
>  #include <mach/kirkwood.h>
> +#include <mach/gpio.h>
>  #include <plat/mvsdio.h>
>  #include "common.h"
>  #include "mpp.h"
> @@ -57,7 +58,15 @@ static struct mvsdio_platform_data openrd_mvsdio_data = {
>  };
>  
>  static unsigned int openrd_mpp_config[] __initdata = {
> +	MPP12_SD_CLK,
> +	MPP13_SD_CMD,
> +	MPP14_SD_D0,
> +	MPP15_SD_D1,
> +	MPP16_SD_D2,
> +	MPP17_SD_D3,
> +	MPP28_GPIO,
>  	MPP29_GPIO,
> +	MPP34_GPIO,
>  	0
>  };
>  
> @@ -67,6 +76,71 @@ static struct i2c_board_info i2c_board_info[] __initdata = {
>  	},
>  };
>  
> +static int __initdata uart1;
> +
> +static int __init sd_uart_selection(char *str)
> +{
> +	/* Default is SD. Change if required, for UART */
> +	if (!str)
> +		return 0;
> +
> +	if (!strncmp(str, "232", 3)) {
> +		uart1 = 232;
> +	} else if (!strncmp(str, "485", 3)) {
> +		/* OpenRD-Base doesn't have RS485. Treat is as an
> +		 * unknown argument & just have default setting -
> +		 * which is SD */
> +		if (machine_is_openrd_base())
> +			return 1;
> +
>
uart1 = -ENODEV;
return 1;

> +		uart1 = 485;
> +	}
> +	return 1;
>
uart1 = -EINVAL;
return 1;

> +}
> +/* Parse boot_command_line string uart=232/485 */
> +__setup("uart=", sd_uart_selection);
> +
>
'kirkwood_init_uart1' instead maybe, only going to annoy someone 
otherwise I'm guessing.

> +static int __init uart1_mpp_config(void)
> +{
> +	/* Configure MPP for UART1 */
> +	unsigned int uart1_mpp_config[] = {
> +		MPP13_UART1_TXD,
> +		MPP14_UART1_RXD,
> +		0
> +	};
> +
> +	kirkwood_mpp_conf(uart1_mpp_config);
> +
> +	if (gpio_request(34, "SD_UART1_SEL")) {
> +		printk(KERN_ERR "GPIO request failed for SD/UART1 selection"
> +				", gpio: 34\n");
> +		return -EIO;
> +	}
> +
> +	if (gpio_request(28, "RS232_RS485_SEL")) {
> +		printk(KERN_ERR "GPIO request failed for RS232/RS485 selection"
> +				", gpio# 28\n");
> +		gpio_free(34);
> +		return -EIO;
> +	}
> +
> +	/* Select UART1
> +	 * Pin # 34: 0 => UART1, 1 => SD */
> +	gpio_direction_output(34, 0);
> +
> +	/* Select RS232 OR RS485
> +	 * Pin # 28: 0 => RS232, 1 => RS485 */
> +	if (uart1 == 232)
> +		gpio_direction_output(28, 0);
> +	else
> +		gpio_direction_output(28, 1);
> +
> +	gpio_free(34);
> +	gpio_free(28);
> +
> +	return 0;
> +}
> +
>  static void __init openrd_init(void)
>  {
>  	/*
> @@ -90,7 +164,6 @@ static void __init openrd_init(void)
>  		kirkwood_ge01_init(&openrd_ge01_data);
>  
>  	kirkwood_sata_init(&openrd_sata_data);
> -	kirkwood_sdio_init(&openrd_mvsdio_data);
>  
>  	kirkwood_i2c_init();
>  
> @@ -99,6 +172,23 @@ static void __init openrd_init(void)
>  			ARRAY_SIZE(i2c_board_info));
>  		kirkwood_audio_init();
>  	}
> +
> +	if (!uart1) {
> +		/* Select SD
> +		 * Pin # 34: 0 => UART1, 1 => SD */
> +		if (gpio_request(34, "SD_UART1_SEL")) {
> +			printk(KERN_ERR "GPIO request failed for SD/UART1 "
> +					"selection, gpio: 34\n");
> +		} else {
> +
> +			gpio_direction_output(34, 1);
> +			gpio_free(34);
> +			kirkwood_sdio_init(&openrd_mvsdio_data);
> +		}
> +	} else {
>
} else if (uart1 < 0) {
	prink(KERN_WARNING, "<grumble>, uart1 init issue, "
		"defaulting to SD: %d\n", uart1);
} else {

> +		if (!uart1_mpp_config())
> +			kirkwood_uart1_init();
> +	}
>  }
>  
>  static int __init openrd_pci_init(void)
> -- 
> 1.6.6.1

Afterwards, remember to run it through ./scripts/checkpatch.pl.

Cheers

-- 
Alexander Clouter
.sigmonster says: Old MacDonald had an agricultural real estate tax abatement.