[PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board

[Kukjin Kim]

Marek Szyprowski wrote:
> 
> This patch add support for SDHCI blocks on Samsung Aquila board. The
> following host controllers are defined:
> 1. Internal MoviNAND device (permanently wired to the controller)
> 2. Internal WiFI SDIO device (card is activated by power regualor)
> 3. External MMC/SD socket (card detection is provided by external
> gpio interrupt)
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski at samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park at samsung.com>
> ---
>  arch/arm/mach-s5pv210/Kconfig       |    4 +++
>  arch/arm/mach-s5pv210/mach-aquila.c |   39
> +++++++++++++++++++++++++++++++++++
>  2 files changed, 43 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
> index 12a2c6b..c64dff1 100644
> --- a/arch/arm/mach-s5pv210/Kconfig
> +++ b/arch/arm/mach-s5pv210/Kconfig
> @@ -60,8 +60,12 @@ config MACH_AQUILA
>  	select CPU_S5PV210
>  	select ARCH_SPARSEMEM_ENABLE
>  	select S5PV210_SETUP_FB_24BPP
> +	select S5PV210_SETUP_SDHCI
>  	select S3C_DEV_FB
>  	select S5PC110_DEV_ONENAND
> +	select S3C_DEV_HSMMC
> +	select S3C_DEV_HSMMC1
> +	select S3C_DEV_HSMMC2
>  	help
>  	  Machine support for the Samsung Aquila target based on S5PC110
> SoC
> 
> diff --git a/arch/arm/mach-s5pv210/mach-aquila.c
b/arch/arm/mach-s5pv210/mach-
> aquila.c
> index 0992618..a1f8d07 100644
> --- a/arch/arm/mach-s5pv210/mach-aquila.c
> +++ b/arch/arm/mach-s5pv210/mach-aquila.c
> @@ -35,6 +35,7 @@
>  #include <plat/devs.h>
>  #include <plat/cpu.h>
>  #include <plat/fb.h>
> +#include <plat/sdhci.h>
> 
>  /* Following are default values for UCON, ULCON and UFCON UART registers
*/
>  #define S5PV210_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
> @@ -440,11 +441,47 @@ static void __init aquila_pmic_init(void)
>  	s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP);
>  }
> 
> +/* MoviNAND */
> +static struct s3c_sdhci_platdata aquila_hsmmc0_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_PERMANENT,
> +};
> +
> +/* Wireless LAN */
> +static struct s3c_sdhci_platdata aquila_hsmmc1_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_EXTERNAL,
> +	/* ext_cd_{init,cleanup} callbacks will be added later */
> +};
> +
> +/* External Flash */
> +#define AQUILA_EXT_FLASH_EN	S5PV210_MP05(4)
> +#define AQUILA_EXT_FLASH_CD	S5PV210_GPH3(4)
> +static struct s3c_sdhci_platdata aquila_hsmmc2_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_GPIO,
> +	.ext_cd_gpio		= AQUILA_EXT_FLASH_CD,
> +	.ext_cd_gpio_invert	= 1,
> +};
> +
> +static void aquila_setup_sdhci(void)
> +{
> +	gpio_request(AQUILA_EXT_FLASH_EN, "FLASH_EN");
> +	gpio_direction_output(AQUILA_EXT_FLASH_EN, 1);
> +
> +	s3c_sdhci0_set_platdata(&aquila_hsmmc0_data);
> +	s3c_sdhci1_set_platdata(&aquila_hsmmc1_data);
> +	s3c_sdhci2_set_platdata(&aquila_hsmmc2_data);
> +};
> +
>  static struct platform_device *aquila_devices[] __initdata = {
>  	&aquila_i2c_gpio_pmic,
>  	&aquila_device_gpiokeys,
>  	&s3c_device_fb,
>  	&s5pc110_device_onenand,
> +	&s3c_device_hsmmc0,
> +	&s3c_device_hsmmc1,
> +	&s3c_device_hsmmc2,
>  };
> 
>  static void __init aquila_map_io(void)
> @@ -460,6 +497,8 @@ static void __init aquila_machine_init(void)
>  	aquila_pmic_init();
>  	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4,
> i2c_gpio_pmic_devs,
>  			ARRAY_SIZE(i2c_gpio_pmic_devs));
> +	/* SDHCI */
> +	aquila_setup_sdhci();
> 
>  	/* FB */
>  	s3c_fb_set_platdata(&aquila_lcd_pdata);
> --
Looks ok..will apply.

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim at samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.