MXC MMC driver and SDIO peripherals

Dan Williams dcbw at redhat.com
Wed Oct 28 14:46:02 EDT 2009


On Wed, 2009-10-28 at 18:19 +0100, Daniel Mack wrote:
> On Wed, Oct 28, 2009 at 10:06:02AM -0700, Dan Williams wrote:
> > On Wed, 2009-10-28 at 17:47 +0100, Daniel Mack wrote:
> > > I did some more research on this and it turns out that the problem is
> > > related to multi block transfers. At least, this is when it first
> > > occurs.
> > > 
> > > The libertas SDIO driver downloads two firmwares to the device, one
> > > 'helper' and one 'real' firmware The first one only uses chunks of 64
> > > bytes each and that seems to work fine. The real firmware, however,
> > > loads in 512 bytes chunks which the SDIO core breaks up into 16 blocks
> > > of 32 bytes. And this is where the MXC host controller bails out with a
> > > CRC error. Unfortunately, it does not give any more detailed information
> > > about what exactly went wrong.
> > > 
> > > The effect might be related to an errata entry[1], which is what I'm
> > > currently investigating. To do so, I would like to limit the the
> > > communication to singe-block transfers, just to exclude all other
> > > possible (electrical, clock speed, ...) issues. I did that by setting
> > > mmc->max_blk_count to 1 in the the host controller, but then again,
> > > the libertas driver and/or the firmware doesn't like that and dies in
> > > if_sdio_pro_real() with
> > > 
> > >   firmware wants 17 bytes
> > >   firmware helper signalled error
> > > 
> > > Any idea how to get that working with only single block small transfers?
> > 
> > All the Marvell documentation (v5 at least) refers to 512-byte transfers
> > of the second-stage firmware in 32-byte blocks:
> > 
> > Section 2.2.1.1 of the v5 spec states:
> > 
> > "
> > 2) If the length requested by helper is larger than 512 bytes, it is cut
> > into multiple pieces for CMD53 write. The current download length is set
> > to 512 bytes (16 blocks x 32 bytes per block) in each iteration of CMD53
> > write.
> > 3) Host starts the download of 16 blocks of firmware (512 bytes)
> > 4) Host copies the payload to the buffer.
> > 5) Host writes 16 blocks of the firmware image data using CMD 53.
> > 6) Repeat Steps 3 through 5 until the firmware image data specified by
> > the helper (Step 2) for this iteration is downloaded completely.
> > "
> > 
> > The helper firmware may well expect all 16 blocks.  But try adjusting
> > "chunk_size" in if_sdio.c::if_sdio_prog_real() down to one block (ie, 32
> > not 512) and see if the helper pukes.  The code looks like it can handle
> > chunk_size changes just fine.
> 
> The code can, yes. But it seems the helper can't. I think I tried this
> earlier. Here's the output:
> 
> [    5.620000] libertas_sdio mmc0:0001:1: firmware: requesting sd8686_helper.bin
> [    5.700000] libertas sdio: waiting for helper to boot...
> [    5.710000] libertas_sdio mmc0:0001:1: firmware: requesting sd8686.bin
> [    5.770000] libertas sdio: firmware wants 16 bytes
> [    5.780000] libertas sdio: sending 16 bytes (32 bytes) chunk
> [    5.790000] libertas sdio: firmware wants 512 bytes
> [    5.790000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.800000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.810000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.810000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.820000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.830000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.830000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.840000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.840000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.850000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.860000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.860000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.870000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.880000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.880000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.890000] libertas sdio: sending 32 bytes (32 bytes) chunk
> [    5.900000] libertas sdio: firmware wants 17 bytes
> [    5.900000] libertas sdio: firmware helper signalled error
> [    5.910000] libertas: failed to load firmware
> [    5.910000] libertas_sdio: probe of mmc0:0001:1 failed with error -5
> 
> Maybe I need to tweak the core to send 512 bytes in one block instead of
> multiple ones?

Maybe?  But I bet the helper would fail on that too, since it's
expecting 32 byte blocks.

> Just to exclude other issues - seeing the driver coming that far tells
> that electrical issues can't be the reason, right? Or is there anything
> else that changes after the helper is downloaded successfully? Does the
> hardware change anything on the hardware link layer at this point?

I can't think of a reason why it would be electrical, but we can't
exclude that completely of course.  The helper is simply a small program
that knows how to buffer a larger firmware and load that firmware at a
given address in memory on the Libertas.  I don't believe it has
anything to do with the SDIO bits of the chip, but I don't know for sure
since I don't have the code for it.

I think this just boils down to a pretty badly implemented SDHC :(

Dan





More information about the libertas-dev mailing list