[PATCH] libertas: updated readme file

[Dan Williams]

On Fri, 2007-03-30 at 15:44 -0700, Luis Carlos Cobo Rus wrote:
> ---
>  drivers/net/wireless/libertas/README |   19 +++++++++++++++----
>  1 files changed, 15 insertions(+), 4 deletions(-)

Applied.

> diff --git a/drivers/net/wireless/libertas/README
> b/drivers/net/wireless/libertas/README
> index c93b9b5..ba918ae 100644
> --- a/drivers/net/wireless/libertas/README
> +++ b/drivers/net/wireless/libertas/README
> @@ -100,15 +100,19 @@ Version 5 Command:
>  	iwpriv ethX beaconinterval
> 
>  BT Commands:
> -	The blinding table (BT) contains a list of mac addresses that should be
> -	ignored by the firmware.  It is primarily used for debugging and
> -	testing networks.  It can be edited and inspected with the following
> -	commands:
> +	The blinding table (BT) contains a list of mac addresses that will be,
> +	by default, ignored by the firmware. It is also possible to invert this
> +	behavior so that we will ignore all traffic except for the portion
> +	coming from mac addresess in the list. It is primarily used for
> +	debugging and testing networks.  It can be edited and inspected with
> +	the following commands:
> 
>  	iwpriv ethX bt_reset
>  	iwpriv ethX bt_add <mac_address>
>  	iwpriv ethX bt_del <mac_address>
>  	iwpriv ethX bt_list <id>
> +	iwpriv ethX bt_get_invert <n>
> +	iwpriv ethX bt_set_invert <n>
> 
>  FWT Commands:
>  	The forwarding table (FWT) is a feature used to manage mesh network
> @@ -666,6 +670,9 @@ fwt_add
>  				   preferred, default is 0)
>  		dir		-- direction (1 for direct, 0 for reverse,
>  				   default is 1)
> +		rate		-- data rate used for transmission to the RA,
> +				   as specified for the rateadapt command,
> +				   default is 3 (11Mbps)
>  		ssn		-- Source Sequence Number (time at the RA for
>  				   reverse routes.  Default is 0)
>  		dsn		-- Destination Sequence Number (time at the DA
> @@ -728,8 +735,11 @@ fwt_list
>  	where the different fields are:-
>  		da		-- DA MAC address (in the form "00:11:22:33:44:55")
>  		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
> +		valid		-- whether the route is valid (0 if not valid)
>  		metric		-- route metric (cost: smaller-metric routes are preferred)
>  		dir		-- direction (1 for direct, 0 for reverse)
> +		rate		-- data rate used for transmission to the RA,
> +				   as specified for the rateadapt command
>  		ssn		-- Source Sequence Number (time at the RA for reverse routes)
>  		dsn		-- Destination Sequence Number (time at the DA for direct routes)
>  		hopcount	-- hop count (currently unused)
> @@ -737,6 +747,7 @@ fwt_list
>  		expiration	-- entry expiration (in ticks, where a tick is 1024us,
> or ~ 1ms. Use 0 for an indefinite entry)
>  		sleepmode	-- RA's sleep mode (currently unused)
>  		snr		-- SNR in the link to RA (currently unused)
> +		precursor	-- predecessor in direct routes
> 
>  fwt_list_route
>  	This command is used to list a route from the FWT table. The only
> -- 
> 1.4.3
> 
>