[source] lantiq: add Netgear DM200 support
LEDE Commits
lede-commits at lists.infradead.org
Fri Jul 7 04:41:41 PDT 2017
mkresin pushed a commit to source.git, branch master:
https://git.lede-project.org/50e3659703113df036e755e0d483172c3b809242
commit 50e3659703113df036e755e0d483172c3b809242
Author: Thomas Nixon <tom at tomn.co.uk>
AuthorDate: Sun Apr 23 22:07:17 2017 +0100
lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:
CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
RAM: 64MiB
Flash: 8MiB
Ethernet: 1x100M
DSL: VDSL2+, ADSL2+
reset button, 3x bi-color LEDs
Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.
To upgrade from the vendor firmware, upload factory.img
The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.
Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.
Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.
Signed-off-by: Thomas Nixon <tom at tomn.co.uk>
---
target/linux/lantiq/base-files/etc/board.d/01_leds | 3 +
.../linux/lantiq/base-files/etc/board.d/02_network | 6 +
target/linux/lantiq/dts/DM200.dts | 214 +++++++++++++++++++++
target/linux/lantiq/image/Makefile | 11 ++
4 files changed, 234 insertions(+)
diff --git a/target/linux/lantiq/base-files/etc/board.d/01_leds b/target/linux/lantiq/base-files/etc/board.d/01_leds
index 634f479..817e2e9 100755
--- a/target/linux/lantiq/base-files/etc/board.d/01_leds
+++ b/target/linux/lantiq/base-files/etc/board.d/01_leds
@@ -50,6 +50,9 @@ ARV7519RW22)
BTHOMEHUBV5A)
ucidef_set_led_default "dimmed" "dimmed" "dimmed" "0"
;;
+DM200)
+ ucidef_set_led_netdev "lan" "lan" "dm200:green:lan" "eth0"
+ ;;
FRITZ7320)
ucidef_set_led_netdev "wifi" "wifi" "fritz7320:green:wlan" "wlan0"
;;
diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network b/target/linux/lantiq/base-files/etc/board.d/02_network
index 55498b9..c245a8f 100755
--- a/target/linux/lantiq/base-files/etc/board.d/02_network
+++ b/target/linux/lantiq/base-files/etc/board.d/02_network
@@ -100,6 +100,12 @@ DGN3500*)
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5t at eth0"
;;
+DM200)
+ lan_mac=$(mtd_get_mac_binary ART 0)
+ wan_mac=$(macaddr_add "$lan_mac" 1)
+ ucidef_set_interface_lan 'eth0'
+ ;;
+
EASY80920NAND|EASY80920NOR)
lan_mac=$(mtd_get_mac_ascii uboot_env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" 1)
diff --git a/target/linux/lantiq/dts/DM200.dts b/target/linux/lantiq/dts/DM200.dts
new file mode 100644
index 0000000..050d558
--- /dev/null
+++ b/target/linux/lantiq/dts/DM200.dts
@@ -0,0 +1,214 @@
+/dts-v1/;
+
+#include "vr9.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "DM200 - Netgear DM200";
+
+ chosen {
+ bootargs = "console=ttyLTQ0,115200";
+ };
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+
+ led-dsl = &dsl_green;
+ };
+
+ memory at 0 {
+ reg = <0x0 0x4000000>;
+ };
+
+ fpi at 10000000 {
+ gpio: pinmux at E100B10 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&state_default>;
+
+ state_default: pinmux {
+ mdio {
+ lantiq,groups = "mdio";
+ lantiq,function = "mdio";
+ };
+ };
+
+ pins_spi_default: pins_spi_default {
+ spi_in {
+ lantiq,groups = "spi_di";
+ lantiq,function = "spi";
+ };
+ spi_out {
+ lantiq,groups = "spi_do", "spi_clk", "spi_cs4";
+ lantiq,function = "spi";
+ lantiq,output = <1>;
+ };
+ };
+ };
+
+ pcie at d900000 {
+ status = "disabled";
+ };
+ };
+
+ gphy-xrx200 {
+ compatible = "lantiq,phy-xrx200";
+ firmware = "lantiq/vr9_phy22f_a2x.bin";
+ phys = [ 01 ];
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <100>;
+ reset {
+ label = "reset";
+ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ annexa {
+ gpio-export,name = "annexa";
+ gpio-export,output = <0>;
+ gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ };
+ annexb {
+ gpio-export,name = "annexb";
+ gpio-export,output = <0>;
+ gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_amber: power_amber {
+ label = "dm200:amber:power";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+ power_green: power_green {
+ label = "dm200:green:power";
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan_amber {
+ label = "dm200:amber:lan";
+ gpios = <&gpio 33 GPIO_ACTIVE_HIGH>;
+ };
+ lan_green {
+ label = "dm200:green:lan";
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ dsl_amber {
+ label = "dm200:amber:dsl";
+ gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ };
+ dsl_green: dsl_green {
+ label = "dm200:green:dsl";
+ gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&spi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pins_spi_default>;
+
+ status = "ok";
+
+ m25p80 at 4 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <4 0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ reg = <0x0 0x20000>;
+ label = "uboot";
+ read-only;
+ };
+
+ partition at 20000 {
+ reg = <0x20000 0x10000>;
+ label = "gphyfirmware";
+ read-only;
+ };
+
+ partition at 30000 {
+ reg = <0x30000 0x7b0000>;
+ label = "firmware";
+ };
+
+ partition at 7e0000 {
+ reg = <0x7e0000 0x10000>;
+ label = "sysconfig";
+ read-only;
+ };
+
+ partition at 7f0000 {
+ reg = <0x7f0000 0x2000>;
+ label = "ubootconfig";
+ read-only;
+ };
+
+ partition at 7f2000 {
+ reg = <0x7f2000 0x1000>;
+ label = "ART";
+ read-only;
+ };
+
+ partition at 7f3000 {
+ reg = <0x7f3000 0x1000>;
+ label = "pot";
+ read-only;
+ };
+
+ partition at 7f4000 {
+ reg = <0x7f4000 0xc000>;
+ label = "ret";
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ lan: interface at 0 {
+ compatible = "lantiq,xrx200-pdi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ ethernet at 4 {
+ compatible = "lantiq,xrx200-pdi-port";
+ reg = <4>;
+ phy-mode = "mii";
+ phy-handle = <&phy13>;
+ };
+ };
+
+ mdio at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "lantiq,xrx200-mdio";
+ phy13: ethernet-phy at 13 {
+ reg = <0x13>;
+ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22";
+ };
+ };
+};
diff --git a/target/linux/lantiq/image/Makefile b/target/linux/lantiq/image/Makefile
index 122a8a5..1678b1b 100644
--- a/target/linux/lantiq/image/Makefile
+++ b/target/linux/lantiq/image/Makefile
@@ -513,6 +513,17 @@ define Device/BTHOMEHUBV5A
endef
TARGET_DEVICES += BTHOMEHUBV5A
+define Device/DM200
+ IMAGES := sysupgrade.bin factory.img
+ IMAGE/factory.img := $$(IMAGE/sysupgrade.bin) | netgear-dni
+ IMAGE_SIZE := 7872k
+ DEVICE_TITLE := Netgear DM200
+ NETGEAR_BOARD_ID := DM200
+ NETGEAR_HW_ID := 29765233+8+0+64+0+0
+endef
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
+TARGET_DEVICES += DM200
+
define Device/EASY80920NAND
$(Device/lantiqFullImage)
IMAGE_SIZE := 64512k
More information about the lede-commits
mailing list