Problem with wpa_supplicant: IOCTL error.

[wilk3ert wilk]

2008/3/7, Jouni Malinen <j at w1.fi>:
> Could you please send the error message with full debugging enabled (-dd
> on the command line)?

Yes.
Here it is:

Initializing interface 'wlan0_rename' conf '/etc/wpa_supplicant.conf'
driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='DIR=/var/run/wpa_supplicant/ GROUP=wheel'
Line: 2 - start of a new network block
ssid - hexdump_ascii(len=8):
     41 4c 4d 41 57 49 46 49                           ALMAWIFI
scan_ssid=1 (0x1)
pairwise: 0x8
key_mgmt: 0x1
eap methods - hexdump(len=16): 00 00 00 00 00 00 00 19 00 00 00 00 00 00 00 00
identity - hexdump_ascii(len=33):
     76 69 6e 63 65 6e 7a 6f 2e 66 65 72 72 61 72 69   <username>
     32 40 73 74 75 64 69 6f 2e 75 6e 69 62 6f 2e 69   <username>
     74                                                <username>
password - hexdump_ascii(len=9):
     6d 61 78 33 73 74 61 66 66                        <password>
ca_cert - hexdump_ascii(len=16):
     2f 65 74 63 2f 63 65 72 74 2f 63 61 2e 70 65 6d   /etc/cert/ca.pem
phase1 - hexdump_ascii(len=11):
     70 65 61 70 6c 61 62 65 6c 3d 30                  peaplabel=0
phase2 - hexdump_ascii(len=13):
     61 75 74 68 3d 4d 53 43 48 41 50 56 32            auth=MSCHAPV2
Line 13: removed CCMP from group cipher list since it was not allowed
for pairwise cipher
Priority group 0
   id=0 ssid='ALMAWIFI'
Initializing interface (2) 'wlan0_rename'
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:11:24:21:9b:09
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x1 - RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Using existing control interface directory.
CTRL: Invalid group 'wheel'
Failed to initialize control interface 'DIR=/var/run/wpa_supplicant/
GROUP=wheel'.
You may have another wpa_supplicant process already running or the file was
left by an unclean termination of wpa_supplicant in which case you will need
to manually remove this file before starting wpa_supplicant again.

Failed to add interface wlan0_rename
State: DISCONNECTED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 5 value 0x0 - wpa_driver_wext_set_countermeasures
ioctl[SIOCSIWAUTH]: Operation not supported
WEXT auth param 4 value 0x0 - No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6


--
.:www.wilky.it:.