hostap_cs.conf

Andrea G. Forte andreaf
Fri Feb 20 12:01:53 PST 2004


> Could you please test this again without first loading linux-wlan-ng
> driver?
Does it matter if I used the wlan-ng driver with a different card before
trying the HostAP with the WCF11? However I will try again.

> I would also need to get the addresses from the oops resolved to
> symbols. Any change that you could pipe it through ksymoops? If not, I
> would need to get System.map and vmlinux from the kernel build tree and
> the Host AP modules (hostap*.o) and contents of /proc/ksyms and
> /proc/modules from the system to be able to resolve the symbols myself
>
I will send them to you as soon as I can...right now I am trying the older
kernel.

> Is this ANY SSID comment only about 0.0.4 and 0.1.2 just crashes?
>
Yes, hostAP 0.1.2 just crashes. The comment about the essid was about
0.0.4 but also about the WCF11 card itself, meaning that if I use the
wlan-ng drivers with the WCF11 card and change the essid from ANY to
something specific, the WCF11 gets stuck to "Initializing..." and
never connects. Could it be a problem related to the card firmware instead
of the driver?


One more thing. For some reason hostAP 0.0.4 seems to work
better than the 0.1.2. I tried the hostAP 0.0.4 with the old kernel 2.4.6
and what happens is that hostAP gets loaded and there are not error
messages in the dmesg. We sniffed the card and it came out that the card
is sending probe requests(we set as default Managed mode) but NO APs
respond to those probe requests...any idea why this would happen?
The essid is set as default to our APs' essid.
It almost looks as if the APs cannot "hear" those probe requests.

Thank you,
Andrea

On Thu, 19 Feb 2004, Jouni Malinen wrote:

> On Thu, Feb 19, 2004 at 02:59:21PM -0500, Andrea G. Forte wrote:
>
> > I have updated the kernel to 2.4.18 and used HostAP 0.1.12.
> > When I use the HostAP driver I get a lot of errors in dmesg, the following
> > is the beginning of the errors in dmesg:
>
> Could you please test this again without first loading linux-wlan-ng
> driver? I would also need to get the addresses from the oops resolved to
> symbols. Any change that you could pipe it through ksymoops? If not, I
> would need to get System.map and vmlinux from the kernel build tree and
> the Host AP modules (hostap*.o) and contents of /proc/ksyms and
> /proc/modules from the system to be able to resolve the symbols myself
>
>
> > We also installed hostap 0.0.4 using the kernel 2.4.6 and everything
> > seemed to work. The only problem is that it would not connect to any AP
> > when in Managed mode and it would not work as AP in Master mode...we could
> > not see it when scanning.
> > We noticed that the WCF11 works fine if ANY is selected as essid and it
> > gives some problems if the essid is specified. Could this be the problem
> > (since hostAP does not support ANY as essid)? How could we fix this?
>
> Is this ANY SSID comment only about 0.0.4 and 0.1.2 just crashes?
>
> --
> Jouni Malinen                                            PGP id EFC895FA
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap
>




More information about the Hostap mailing list