[PATCH RFC v2 1/8] bus: mhi: host: add mhi_power_down_no_destroy()
Manivannan Sadhasivam
mani at kernel.org
Wed Dec 20 08:51:13 PST 2023
On Wed, Dec 20, 2023 at 10:02:25PM +0530, Manivannan Sadhasivam wrote:
> On Tue, Dec 05, 2023 at 02:29:33PM +0200, Kalle Valo wrote:
> > Manivannan Sadhasivam <mani at kernel.org> writes:
> >
> > > On Mon, Nov 27, 2023 at 06:20:15PM +0200, Kalle Valo wrote:
> > >
> > >> From: Baochen Qiang <quic_bqiang at quicinc.com>
> > >>
> > >> If ath11k tries to call mhi_power_up() during resume it fails:
> > >>
> > >> ath11k_pci 0000:06:00.0: timeout while waiting for restart complete
> > >>
> > >> This happens because when calling mhi_power_up() the MHI subsystem eventually
> > >> calls device_add() from mhi_create_devices() but the device creation is
> > >> deferred:
> > >>
> > >> mhi mhi0_IPCR: Driver qcom_mhi_qrtr force probe deferral
> > >>
> > >> The reason for deferring device creation is explained in dpm_prepare():
> > >>
> > >> /*
> > >> * It is unsafe if probing of devices will happen during suspend or
> > >> * hibernation and system behavior will be unpredictable in this case.
> > >> * So, let's prohibit device's probing here and defer their probes
> > >> * instead. The normal behavior will be restored in dpm_complete().
> > >> */
> > >>
> > >> Because the device probe is deferred, the qcom_mhi_qrtr_probe() is not called and
> > >> qcom_mhi_qrtr_dl_callback() fails silently as qdev is zero:
> > >>
> > >> static void qcom_mhi_qrtr_dl_callback(struct mhi_device *mhi_dev,
> > >> struct mhi_result *mhi_res)
> > >> {
> > >> struct qrtr_mhi_dev *qdev = dev_get_drvdata(&mhi_dev->dev);
> > >> int rc;
> > >>
> > >> if (!qdev || mhi_res->transaction_status)
> > >> return;
> > >>
> > >> So what this means that QRTR is not delivering messages and the QMI connection
> > >> is not working between ath11k and the firmware, resulting a failure in firmware
> > >> initialisation.
> > >>
> > >> To fix this add new function mhi_power_down_no_destroy() which does not destroy
> > >> the devices during power down. This way mhi_power_up() can be called during
> > >> resume and we can get ath11k hibernation working with the following patches.
> > >>
> > >> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
> > >>
> > >> Signed-off-by: Baochen Qiang <quic_bqiang at quicinc.com>
> > >> Signed-off-by: Kalle Valo <quic_kvalo at quicinc.com>
> > >
> > > Any reason for reposting this series without discussing the suggestion from
> > > Mayank?
> >
> > Baochen quickly sent me fixes for the v1 review comments, as I have been
> > out of office for some time I didn't want to sit on Baochen's fixes for
> > too long. Better to get them out of the door as soon as possible. I will
> > definitely look at Mayank's proposal but that will take longer.
> >
> > > As I said in the internal thread, this patch breaks the Linux device
> > > driver model by not destroying the "struct device" when the actual
> > > device gets removed.
> >
> > This patchset has been tested by several people, I'm even using this
> > patchset on main laptop every day, and we haven't noticed any issues.
> >
> > Can you elaborate more about this driver model? We are not removing any
> > ath11k devices, we just want to power down the ath11k (and in the future
> > ath12k) devices for suspend and power up during resume.
> >
>
> Devices (struct dev) for each channels are created once the device (WLAN) enters
> runtime mode such as (MISSION, SBL etc...). During hibernation, ath11k stack
> calls mhi_power_down() which essentially resets the device to POR and also the
> stack powers down the device properly.
>
> In that case, MHI channels do not exist as the device (WLAN) itself is powered
> down. As per kernel driver model, each struct device is tied to its reference
> count. And the reference count should be decremented whenever the actual device
> is not in use. Once the actual device is removed from the system, then the
> respective struct device has to be destroyed altogether.
>
> So in this case, even though the channels are not active (present) in the
> device, the device itself gets powered off, you want MHI stack to keep the
> struct device active, which is against the model I referenced above.
>
> To fix this issue properly, we need to investigate on how other subsystems are
> handling this situation (device getting powered down during hibernation), like
> USB.
>
To me it all sounds like the probe deferral is not handled properly in mac80211
stack. As you mentioned in the commit message that the dpm_prepare() blocks
probing of devices. It gets unblocked and trigerred in dpm_complete():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/base/power/main.c#n1131
So if mac80211/ath11k cannot probe the devices at the dpm_complete() stage, then
it is definitely an issue that needs to be fixed properly.
- Mani
> - Mani
>
> > > We should try to explore alternate options instead of persisting with
> > > this solution.
> >
> > What other options we have here? At least Baochen is not optimistic that
> > using PM_POST_HIBERNATION as a workaround would work. The issue we have
> > here is that mhi_power_up() doesn't work in the resume handler and
> > that's what we should try to fix, not make workarounds.
> >
> > --
> > https://patchwork.kernel.org/project/linux-wireless/list/
> >
> > https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
>
> --
> மணிவண்ணன் சதாசிவம்
--
மணிவண்ணன் சதாசிவம்
More information about the ath11k
mailing list