From felix at kaechele.ca  Tue Nov  5 07:39:27 2024
From: felix at kaechele.ca (Felix Kaechele)
Date: Tue, 5 Nov 2024 10:39:27 -0500
Subject: [PATCH v2 2/2] wifi: ath10k: add support for QCA9379 hw1.0 SDIO
In-Reply-To: <20240908013244.496382-3-felix@kaechele.ca>
References: <20240908013244.496382-1-felix@kaechele.ca>
 <20240908013244.496382-3-felix@kaechele.ca>
Message-ID: <c1385aa1-0d41-4ed7-a00c-e40c69bafeaa@kaechele.ca>

Gentle ping on this one.

It still applies cleanly against the ath/master branch as of today.

If there's no chance of this going in please let me know and I'll stop 
re-sending this patch.

I understand that bandwidth for ath10k related requests is minimal these 
days and there may not be an interest in fixing what are possibly 
firmware related issues for this rather obscure IoT/Automotive (SDIO, no 
less!) chipset.
I unfortunately don't have the information, documentation and latest 
firmware images available on my side to help with this either.
I am, however, always willing to work with someone on fixing any of the 
outstanding issues.

Thanks!
Felix

On 2024-09-07 21:32, Felix Kaechele wrote:
> This adds support for the QCA9379-3 SDIO SoC. It is part of the
> QCA6174 SDIO family.
> 
> While the device is generally working, there are some remaining issues:
> - the card will perform a full reconnect upon expiry of the Group Key
>    renewal interval
> - rx rates are not reported correctly (i.e. always show as 6.0 MBit/s)
> 
> More debugging would need to be done on these, preferably by people with
> access to proper documentation.
> 
> This change was tested on a device that uses a LITEON WCBN3510A module.
> The module was tested in WPA2 and WPA3 Personal scenarios using iperf3.
> Performance was comparable to the same device using the vendor driver in
> the same environment.
> 
> Tested-on: QCA9379 hw1.0 SDIO WLAN.NPL.1.6-00163-QCANPLSWPZ-1
> 
> Signed-off-by: Felix Kaechele <felix at kaechele.ca>
> ---
>   drivers/net/wireless/ath/ath10k/core.c      | 37 +++++++++++++++++++++
>   drivers/net/wireless/ath/ath10k/hw.h        | 10 ++++++
>   drivers/net/wireless/ath/ath10k/pci.c       |  2 ++
>   drivers/net/wireless/ath/ath10k/sdio.c      |  5 ++-
>   drivers/net/wireless/ath/ath10k/targaddrs.h |  3 ++
>   5 files changed, 56 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
> index b3294287bce1..32d5d4be8830 100644
> --- a/drivers/net/wireless/ath/ath10k/core.c
> +++ b/drivers/net/wireless/ath/ath10k/core.c
> @@ -661,6 +661,42 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
>   		.delay_unmap_buffer = false,
>   		.mcast_frame_registration = false,
>   	},
> +	{
> +		.id = QCA9379_HW_1_0_DEV_VERSION,
> +		.dev_id = QCA9379_1_0_DEVICE_ID,
> +		.bus = ATH10K_BUS_SDIO,
> +		.name = "qca9379 hw1.0 sdio",
> +		.patch_load_addr = QCA9379_HW_1_0_PATCH_LOAD_ADDR,
> +		.uart_pin = 19,
> +		.otp_exe_param = 0,
> +		.channel_counters_freq_hz = 88000,
> +		.max_probe_resp_desc_thres = 0,
> +		.cal_data_len = 0,
> +		.fw = {
> +			.dir = QCA9379_HW_1_0_FW_DIR,
> +			.board_size = QCA9379_BOARD_DATA_SZ,
> +			.board_ext_size = QCA9379_BOARD_EXT_DATA_SZ,
> +		},
> +		.rx_desc_ops = &qca988x_rx_desc_ops,
> +		.hw_ops = &qca6174_sdio_ops,
> +		.hw_clk = qca6174_clk,
> +		.target_cpu_freq = 176000000,
> +		.decap_align_bytes = 4,
> +		.n_cipher_suites = 8,
> +		.num_peers = 10,
> +		.ast_skid_limit = 0x10,
> +		.num_wds_entries = 0x20,
> +		.uart_pin_workaround = true,
> +		.tx_stats_over_pktlog = false,
> +		.credit_size_workaround = true,
> +		.bmi_large_size_download = true,
> +		.supports_peer_stats_info = false,
> +		.dynamic_sar_support = false,
> +		.hw_restart_disconnect = false,
> +		.use_fw_tx_credits = true,
> +		.delay_unmap_buffer = false,
> +		.mcast_frame_registration = false,
> +	},
>   	{
>   		.id = QCA4019_HW_1_0_DEV_VERSION,
>   		.dev_id = 0,
> @@ -3602,6 +3638,7 @@ struct ath10k *ath10k_core_create(size_t priv_size, struct device *dev,
>   		break;
>   	case ATH10K_HW_QCA6174:
>   	case ATH10K_HW_QCA9377:
> +	case ATH10K_HW_QCA9379:
>   		ar->regs = &qca6174_regs;
>   		ar->hw_ce_regs = &qcax_ce_regs;
>   		ar->hw_values = &qca6174_values;
> diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
> index 442091c6dfd2..419fa1888e75 100644
> --- a/drivers/net/wireless/ath/ath10k/hw.h
> +++ b/drivers/net/wireless/ath/ath10k/hw.h
> @@ -30,6 +30,7 @@ enum ath10k_bus {
>   #define QCA9888_2_0_DEVICE_ID	(0x0056)
>   #define QCA9984_1_0_DEVICE_ID	(0x0046)
>   #define QCA9377_1_0_DEVICE_ID   (0x0042)
> +#define QCA9379_1_0_DEVICE_ID   (0x0042)
>   #define QCA9887_1_0_DEVICE_ID   (0x0050)
>   
>   /* QCA988X 1.0 definitions (unsupported) */
> @@ -59,6 +60,9 @@ enum ath10k_bus {
>   #define QCA9377_HW_1_0_DEV_VERSION	0x05020000
>   #define QCA9377_HW_1_1_DEV_VERSION	0x05020001
>   
> +/* QCA9379 target BMI version signatures */
> +#define QCA9379_HW_1_0_DEV_VERSION	0x05040000
> +
>   enum qca6174_pci_rev {
>   	QCA6174_PCI_REV_1_1 = 0x11,
>   	QCA6174_PCI_REV_1_3 = 0x13,
> @@ -115,6 +119,10 @@ enum qca9377_chip_id_rev {
>   #define QCA9377_HW_1_0_FW_DIR          ATH10K_FW_DIR "/QCA9377/hw1.0"
>   #define QCA9377_HW_1_0_PATCH_LOAD_ADDR	0x1234
>   
> +/* QCA9379 1.0 definitions */
> +#define QCA9379_HW_1_0_FW_DIR		ATH10K_FW_DIR "/QCA9379/hw1.0"
> +#define QCA9379_HW_1_0_PATCH_LOAD_ADDR	0x1234
> +
>   /* QCA4019 1.0 definitions */
>   #define QCA4019_HW_1_0_DEV_VERSION     0x01000000
>   #define QCA4019_HW_1_0_FW_DIR          ATH10K_FW_DIR "/QCA4019/hw1.0"
> @@ -230,6 +238,7 @@ enum ath10k_hw_rev {
>   	ATH10K_HW_QCA9888,
>   	ATH10K_HW_QCA9984,
>   	ATH10K_HW_QCA9377,
> +	ATH10K_HW_QCA9379,
>   	ATH10K_HW_QCA4019,
>   	ATH10K_HW_QCA9887,
>   	ATH10K_HW_WCN3990,
> @@ -401,6 +410,7 @@ int ath10k_hw_diag_fast_download(struct ath10k *ar,
>   #define QCA_REV_9888(ar) ((ar)->hw_rev == ATH10K_HW_QCA9888)
>   #define QCA_REV_9984(ar) ((ar)->hw_rev == ATH10K_HW_QCA9984)
>   #define QCA_REV_9377(ar) ((ar)->hw_rev == ATH10K_HW_QCA9377)
> +#define QCA_REV_9379(ar) ((ar)->hw_rev == ATH10K_HW_QCA9379)
>   #define QCA_REV_40XX(ar) ((ar)->hw_rev == ATH10K_HW_QCA4019)
>   #define QCA_REV_WCN3990(ar) ((ar)->hw_rev == ATH10K_HW_WCN3990)
>   
> diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
> index c52a16f8078f..6fee3d52d808 100644
> --- a/drivers/net/wireless/ath/ath10k/pci.c
> +++ b/drivers/net/wireless/ath/ath10k/pci.c
> @@ -1899,6 +1899,7 @@ void ath10k_pci_irq_msi_fw_mask(struct ath10k *ar)
>   		 *  to mask irq/MSI.
>   		 */
>   		break;
> +	case ATH10K_HW_QCA9379:
>   	case ATH10K_HW_WCN3990:
>   		break;
>   	}
> @@ -1927,6 +1928,7 @@ static void ath10k_pci_irq_msi_fw_unmask(struct ath10k *ar)
>   		 *  to unmask irq/MSI.
>   		 */
>   		break;
> +	case ATH10K_HW_QCA9379:
>   	case ATH10K_HW_WCN3990:
>   		break;
>   	}
> diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
> index 08a6f36a6be9..24123d23ad5a 100644
> --- a/drivers/net/wireless/ath/ath10k/sdio.c
> +++ b/drivers/net/wireless/ath/ath10k/sdio.c
> @@ -1105,6 +1105,7 @@ static void ath10k_sdio_set_mbox_info(struct ath10k *ar)
>   				ATH10K_HIF_MBOX0_EXT_WIDTH_ROME_2_0;
>   		break;
>   	case (SDIO_DEVICE_ID_ATHEROS_QCA9377 & 0x0F00):
> +	case (SDIO_DEVICE_ID_ATHEROS_QCA9379 & 0x0F00):
>   		mbox_info->ext_info[0].htc_ext_sz =
>   			ATH10K_HIF_MBOX0_EXT_WIDTH_ROME_2_0;
>   		break;
> @@ -2597,7 +2598,8 @@ static int ath10k_sdio_probe(struct sdio_func *func,
>   
>   	dev_id_base = (id->device & 0x0F00);
>   	if (dev_id_base != (SDIO_DEVICE_ID_ATHEROS_AR6005 & 0x0F00) &&
> -	    dev_id_base != (SDIO_DEVICE_ID_ATHEROS_QCA9377 & 0x0F00)) {
> +	    dev_id_base != (SDIO_DEVICE_ID_ATHEROS_QCA9377 & 0x0F00) &&
> +	    dev_id_base != (SDIO_DEVICE_ID_ATHEROS_QCA9379 & 0x0F00)) {
>   		ret = -ENODEV;
>   		ath10k_err(ar, "unsupported device id %u (0x%x)\n",
>   			   dev_id_base, id->device);
> @@ -2656,6 +2658,7 @@ static void ath10k_sdio_remove(struct sdio_func *func)
>   static const struct sdio_device_id ath10k_sdio_devices[] = {
>   	{SDIO_DEVICE(SDIO_VENDOR_ID_ATHEROS, SDIO_DEVICE_ID_ATHEROS_AR6005)},
>   	{SDIO_DEVICE(SDIO_VENDOR_ID_ATHEROS, SDIO_DEVICE_ID_ATHEROS_QCA9377)},
> +	{SDIO_DEVICE(SDIO_VENDOR_ID_ATHEROS, SDIO_DEVICE_ID_ATHEROS_QCA9379)},
>   	{},
>   };
>   
> diff --git a/drivers/net/wireless/ath/ath10k/targaddrs.h b/drivers/net/wireless/ath/ath10k/targaddrs.h
> index ba37e6c7ced0..1a0f71126683 100644
> --- a/drivers/net/wireless/ath/ath10k/targaddrs.h
> +++ b/drivers/net/wireless/ath/ath10k/targaddrs.h
> @@ -481,6 +481,9 @@ struct host_interest {
>   #define QCA9377_BOARD_DATA_SZ     QCA6174_BOARD_DATA_SZ
>   #define QCA9377_BOARD_EXT_DATA_SZ 0
>   
> +#define QCA9379_BOARD_DATA_SZ     QCA6174_BOARD_DATA_SZ
> +#define QCA9379_BOARD_EXT_DATA_SZ 0
> +
>   #define QCA99X0_BOARD_DATA_SZ	  12288
>   #define QCA99X0_BOARD_EXT_DATA_SZ 0
>   



From quic_jjohnson at quicinc.com  Tue Nov  5 08:21:42 2024
From: quic_jjohnson at quicinc.com (Jeff Johnson)
Date: Tue, 5 Nov 2024 08:21:42 -0800
Subject: [PATCH v2 2/2] wifi: ath10k: add support for QCA9379 hw1.0 SDIO
In-Reply-To: <c1385aa1-0d41-4ed7-a00c-e40c69bafeaa@kaechele.ca>
References: <20240908013244.496382-1-felix@kaechele.ca>
 <20240908013244.496382-3-felix@kaechele.ca>
 <c1385aa1-0d41-4ed7-a00c-e40c69bafeaa@kaechele.ca>
Message-ID: <06bf90a5-db29-46b4-b983-439c2b32b143@quicinc.com>

On 11/5/2024 7:39 AM, Felix Kaechele wrote:
> Gentle ping on this one.
> 
> It still applies cleanly against the ath/master branch as of today.
> 
> If there's no chance of this going in please let me know and I'll stop 
> re-sending this patch.
> 
> I understand that bandwidth for ath10k related requests is minimal these 
> days and there may not be an interest in fixing what are possibly 
> firmware related issues for this rather obscure IoT/Automotive (SDIO, no 
> less!) chipset.
> I unfortunately don't have the information, documentation and latest 
> firmware images available on my side to help with this either.
> I am, however, always willing to work with someone on fixing any of the 
> outstanding issues.
> 
> Thanks!
> Felix

Kalle has this in his 'deferred' queue in patchwork which means it's still on
his radar, but low priority.

https://patchwork.kernel.org/project/linux-wireless/list/?series=888058&state=*


From tomaspaukrt at email.cz  Tue Nov  5 08:55:53 2024
From: tomaspaukrt at email.cz (Tomas Paukrt)
Date: Tue, 05 Nov 2024 17:55:53 +0100 (CET)
Subject: [PATCH v2 2/2] wifi: ath10k: add support for QCA9379 hw1.0 SDIO
In-Reply-To: <c1385aa1-0d41-4ed7-a00c-e40c69bafeaa@kaechele.ca>
References: <20240908013244.496382-1-felix@kaechele.ca>
	<20240908013244.496382-3-felix@kaechele.ca>
	<c1385aa1-0d41-4ed7-a00c-e40c69bafeaa@kaechele.ca>
Message-ID: <7P.ZxiX.7YuMJP8eRMw.1dAauP@seznam.cz>

I would like to support the adoption of changes like this one, as they essentially cannot break support for other devices.

I submitted simple and non-conflicting patches that added QCA9377-7 support few months ago, but they were also deferred.

Best regards

Tomas


From u.kleine-koenig at baylibre.com  Wed Nov  6 09:07:06 2024
From: u.kleine-koenig at baylibre.com (=?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?=)
Date: Wed,  6 Nov 2024 18:07:06 +0100
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
Message-ID: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>

After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.

Convert all platform drivers below drivers/net/wireless to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.

En passant several whitespace changes are done to make indentation
consistent in the struct initializers.

Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com>
---
Hello,

I did a single patch for all of drivers/net/wireless. While I usually
prefer to do one logical change per patch, this seems to be
overengineering here as the individual changes are really trivial and
shouldn't be much in the way for stable backports. But I'll happily
split the patch if you prefer it split. Also if you object the
indentation stuff, I can rework that.

This is based on today's next, if conflicts arise when you apply it at
some later time and don't want to resolve them, feel free to just drop
the changes to the conflicting files. I'll notice and followup at a
later time then. Or ask me for a fixed resend. (Having said that, I
recommend b4 am -3 + git am -3 which should resolve most conflicts just
fine.)

Best regards
Uwe

 drivers/net/wireless/ath/ath10k/ahb.c                  |  8 ++++----
 drivers/net/wireless/ath/ath10k/snoc.c                 |  6 +++---
 drivers/net/wireless/ath/ath11k/ahb.c                  |  8 ++++----
 drivers/net/wireless/ath/ath5k/ahb.c                   |  8 ++++----
 drivers/net/wireless/ath/ath9k/ahb.c                   | 10 +++++-----
 drivers/net/wireless/ath/wcn36xx/main.c                |  8 ++++----
 .../net/wireless/broadcom/brcm80211/brcmfmac/common.c  |  2 +-
 drivers/net/wireless/mediatek/mt76/mt7603/soc.c        |  2 +-
 drivers/net/wireless/mediatek/mt76/mt7615/soc.c        |  2 +-
 drivers/net/wireless/mediatek/mt76/mt7915/soc.c        |  2 +-
 drivers/net/wireless/ti/wl12xx/main.c                  |  2 +-
 drivers/net/wireless/ti/wl18xx/main.c                  |  4 ++--
 12 files changed, 31 insertions(+), 31 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/ahb.c b/drivers/net/wireless/ath/ath10k/ahb.c
index f0441b3d7dcb..db9f9ebcb62d 100644
--- a/drivers/net/wireless/ath/ath10k/ahb.c
+++ b/drivers/net/wireless/ath/ath10k/ahb.c
@@ -837,12 +837,12 @@ static void ath10k_ahb_remove(struct platform_device *pdev)
 }
 
 static struct platform_driver ath10k_ahb_driver = {
-	.driver         = {
-		.name   = "ath10k_ahb",
+	.driver = {
+		.name = "ath10k_ahb",
 		.of_match_table = ath10k_ahb_of_match,
 	},
-	.probe  = ath10k_ahb_probe,
-	.remove_new = ath10k_ahb_remove,
+	.probe = ath10k_ahb_probe,
+	.remove = ath10k_ahb_remove,
 };
 
 int ath10k_ahb_init(void)
diff --git a/drivers/net/wireless/ath/ath10k/snoc.c b/drivers/net/wireless/ath/ath10k/snoc.c
index 0fe47d51013c..d436a874cd5a 100644
--- a/drivers/net/wireless/ath/ath10k/snoc.c
+++ b/drivers/net/wireless/ath/ath10k/snoc.c
@@ -1885,11 +1885,11 @@ static void ath10k_snoc_shutdown(struct platform_device *pdev)
 }
 
 static struct platform_driver ath10k_snoc_driver = {
-	.probe  = ath10k_snoc_probe,
-	.remove_new = ath10k_snoc_remove,
+	.probe = ath10k_snoc_probe,
+	.remove = ath10k_snoc_remove,
 	.shutdown = ath10k_snoc_shutdown,
 	.driver = {
-		.name   = "ath10k_snoc",
+		.name = "ath10k_snoc",
 		.of_match_table = ath10k_snoc_dt_match,
 	},
 };
diff --git a/drivers/net/wireless/ath/ath11k/ahb.c b/drivers/net/wireless/ath/ath11k/ahb.c
index 916402ad06b8..f2fc04596d48 100644
--- a/drivers/net/wireless/ath/ath11k/ahb.c
+++ b/drivers/net/wireless/ath/ath11k/ahb.c
@@ -1313,12 +1313,12 @@ static void ath11k_ahb_shutdown(struct platform_device *pdev)
 }
 
 static struct platform_driver ath11k_ahb_driver = {
-	.driver         = {
-		.name   = "ath11k",
+	.driver = {
+		.name = "ath11k",
 		.of_match_table = ath11k_ahb_of_match,
 	},
-	.probe  = ath11k_ahb_probe,
-	.remove_new = ath11k_ahb_remove,
+	.probe = ath11k_ahb_probe,
+	.remove = ath11k_ahb_remove,
 	.shutdown = ath11k_ahb_shutdown,
 };
 
diff --git a/drivers/net/wireless/ath/ath5k/ahb.c b/drivers/net/wireless/ath/ath5k/ahb.c
index f27308ccb2f1..cb3e891ee1bd 100644
--- a/drivers/net/wireless/ath/ath5k/ahb.c
+++ b/drivers/net/wireless/ath/ath5k/ahb.c
@@ -218,10 +218,10 @@ static void ath_ahb_remove(struct platform_device *pdev)
 }
 
 static struct platform_driver ath_ahb_driver = {
-	.probe      = ath_ahb_probe,
-	.remove_new = ath_ahb_remove,
-	.driver		= {
-		.name	= "ar231x-wmac",
+	.probe = ath_ahb_probe,
+	.remove = ath_ahb_remove,
+	.driver = {
+		.name = "ar231x-wmac",
 	},
 };
 
diff --git a/drivers/net/wireless/ath/ath9k/ahb.c b/drivers/net/wireless/ath/ath9k/ahb.c
index 1a6697b6e3b4..d4805e02b927 100644
--- a/drivers/net/wireless/ath/ath9k/ahb.c
+++ b/drivers/net/wireless/ath/ath9k/ahb.c
@@ -158,12 +158,12 @@ static void ath_ahb_remove(struct platform_device *pdev)
 }
 
 static struct platform_driver ath_ahb_driver = {
-	.probe      = ath_ahb_probe,
-	.remove_new = ath_ahb_remove,
-	.driver		= {
-		.name	= "ath9k",
+	.probe = ath_ahb_probe,
+	.remove = ath_ahb_remove,
+	.driver = {
+		.name = "ath9k",
 	},
-	.id_table    = ath9k_platform_id_table,
+	.id_table = ath9k_platform_id_table,
 };
 
 MODULE_DEVICE_TABLE(platform, ath9k_platform_id_table);
diff --git a/drivers/net/wireless/ath/wcn36xx/main.c b/drivers/net/wireless/ath/wcn36xx/main.c
index 408776562a7e..8557d4826a46 100644
--- a/drivers/net/wireless/ath/wcn36xx/main.c
+++ b/drivers/net/wireless/ath/wcn36xx/main.c
@@ -1679,10 +1679,10 @@ static const struct of_device_id wcn36xx_of_match[] = {
 MODULE_DEVICE_TABLE(of, wcn36xx_of_match);
 
 static struct platform_driver wcn36xx_driver = {
-	.probe      = wcn36xx_probe,
-	.remove_new = wcn36xx_remove,
-	.driver         = {
-		.name   = "wcn36xx",
+	.probe = wcn36xx_probe,
+	.remove = wcn36xx_remove,
+	.driver = {
+		.name = "wcn36xx",
 		.of_match_table = wcn36xx_of_match,
 	},
 };
diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
index 58d50918dd17..cfcf01eb0daa 100644
--- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
+++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c
@@ -594,7 +594,7 @@ static void brcmf_common_pd_remove(struct platform_device *pdev)
 }
 
 static struct platform_driver brcmf_pd = {
-	.remove_new	= brcmf_common_pd_remove,
+	.remove		= brcmf_common_pd_remove,
 	.driver		= {
 		.name	= BRCMFMAC_PDATA_NAME,
 	}
diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/soc.c b/drivers/net/wireless/mediatek/mt76/mt7603/soc.c
index ec02148a7f1f..08590aa68356 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/soc.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/soc.c
@@ -71,7 +71,7 @@ MODULE_FIRMWARE(MT7628_FIRMWARE_E2);
 
 struct platform_driver mt76_wmac_driver = {
 	.probe		= mt76_wmac_probe,
-	.remove_new	= mt76_wmac_remove,
+	.remove		= mt76_wmac_remove,
 	.driver = {
 		.name = "mt76_wmac",
 		.of_match_table = of_wmac_match,
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/soc.c b/drivers/net/wireless/mediatek/mt76/mt7615/soc.c
index 12e3e4a91d27..06a0f2a141e8 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/soc.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/soc.c
@@ -63,7 +63,7 @@ struct platform_driver mt7622_wmac_driver = {
 		.of_match_table = mt7622_wmac_of_match,
 	},
 	.probe = mt7622_wmac_probe,
-	.remove_new = mt7622_wmac_remove,
+	.remove = mt7622_wmac_remove,
 };
 
 MODULE_FIRMWARE(MT7622_FIRMWARE_N9);
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/soc.c b/drivers/net/wireless/mediatek/mt76/mt7915/soc.c
index 90a6f61d1089..c823a7554a3a 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/soc.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/soc.c
@@ -1303,7 +1303,7 @@ struct platform_driver mt798x_wmac_driver = {
 		.of_match_table = mt798x_wmac_of_match,
 	},
 	.probe = mt798x_wmac_probe,
-	.remove_new = mt798x_wmac_remove,
+	.remove = mt798x_wmac_remove,
 };
 
 MODULE_FIRMWARE(MT7986_FIRMWARE_WA);
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index b26d42b4e3cc..ffbf54776330 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -1939,7 +1939,7 @@ MODULE_DEVICE_TABLE(platform, wl12xx_id_table);
 
 static struct platform_driver wl12xx_driver = {
 	.probe		= wl12xx_probe,
-	.remove_new	= wl12xx_remove,
+	.remove		= wl12xx_remove,
 	.id_table	= wl12xx_id_table,
 	.driver = {
 		.name	= "wl12xx_driver",
diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index 39d8eebb9b6e..4be1110bac88 100644
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -2097,9 +2097,9 @@ MODULE_DEVICE_TABLE(platform, wl18xx_id_table);
 
 static struct platform_driver wl18xx_driver = {
 	.probe		= wl18xx_probe,
-	.remove_new	= wlcore_remove,
+	.remove		= wlcore_remove,
 	.id_table	= wl18xx_id_table,
-	.driver = {
+	.driver		= {
 		.name	= "wl18xx_driver",
 	}
 };

base-commit: 5b913f5d7d7fe0f567dea8605f21da6eaa1735fb
-- 
2.45.2



From quic_jjohnson at quicinc.com  Wed Nov  6 10:22:56 2024
From: quic_jjohnson at quicinc.com (Jeff Johnson)
Date: Wed, 6 Nov 2024 10:22:56 -0800
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
In-Reply-To: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
References: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
Message-ID: <5c6a887c-db74-44b4-9d8c-2e412f938b47@quicinc.com>

On 11/6/2024 9:07 AM, Uwe Kleine-K?nig wrote:
> After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
> return void") .remove() is (again) the right callback to implement for
> platform drivers.
> 
> Convert all platform drivers below drivers/net/wireless to use
> .remove(), with the eventual goal to drop struct
> platform_driver::remove_new(). As .remove() and .remove_new() have the
> same prototypes, conversion is done by just changing the structure
> member name in the driver initializer.
> 
> En passant several whitespace changes are done to make indentation
> consistent in the struct initializers.
> 
> Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com>

I'll let Kalle make the decision if he wants to take this patch into wireless
or if he'd prefer that the parts that have driver-specific projects be split
out separately. If he'll take it as-is, for drivers/net/wireless/ath/*:

Acked-by: Jeff Johnson <quic_jjohnson at quicinc.com>



From toke at toke.dk  Thu Nov  7 01:35:13 2024
From: toke at toke.dk (Toke =?utf-8?Q?H=C3=B8iland-J=C3=B8rgensen?=)
Date: Thu, 07 Nov 2024 10:35:13 +0100
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
In-Reply-To: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
References: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
Message-ID: <87fro375f2.fsf@toke.dk>

Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com> writes:

> After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
> return void") .remove() is (again) the right callback to implement for
> platform drivers.
>
> Convert all platform drivers below drivers/net/wireless to use
> .remove(), with the eventual goal to drop struct
> platform_driver::remove_new(). As .remove() and .remove_new() have the
> same prototypes, conversion is done by just changing the structure
> member name in the driver initializer.
>
> En passant several whitespace changes are done to make indentation
> consistent in the struct initializers.
>
> Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com>

For ath9k:

Acked-by: Toke H?iland-J?rgensen <toke at toke.dk>


From arend.vanspriel at broadcom.com  Thu Nov  7 01:38:11 2024
From: arend.vanspriel at broadcom.com (Arend van Spriel)
Date: Thu, 7 Nov 2024 10:38:11 +0100
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
In-Reply-To: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
References: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
Message-ID: <8f8c6ac8-159a-425e-9d9b-b31c956f700d@broadcom.com>

On 11/6/2024 6:07 PM, Uwe Kleine-K?nig wrote:
> After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
> return void") .remove() is (again) the right callback to implement for
> platform drivers.
> 
> Convert all platform drivers below drivers/net/wireless to use
> .remove(), with the eventual goal to drop struct
> platform_driver::remove_new(). As .remove() and .remove_new() have the
> same prototypes, conversion is done by just changing the structure
> member name in the driver initializer.
> 
> En passant several whitespace changes are done to make indentation
> consistent in the struct initializers.

I am fine with the patch as is, but it is really up to Kalle. For 
brcmfmac here is my...

Acked-by: Arend van Spriel <arend.vanspriel at broadcom.com>


From jirislaby at kernel.org  Thu Nov  7 02:01:14 2024
From: jirislaby at kernel.org (Jiri Slaby)
Date: Thu, 7 Nov 2024 11:01:14 +0100
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
In-Reply-To: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
References: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
Message-ID: <d3890b5e-26e1-46ef-81ba-5427892517bf@kernel.org>

On 06. 11. 24, 18:07, Uwe Kleine-K?nig wrote:
> After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
> return void") .remove() is (again) the right callback to implement for
> platform drivers.
> 
> Convert all platform drivers below drivers/net/wireless to use
> .remove(), with the eventual goal to drop struct
> platform_driver::remove_new(). As .remove() and .remove_new() have the
> same prototypes, conversion is done by just changing the structure
> member name in the driver initializer.
> 
> En passant several whitespace changes are done to make indentation
> consistent in the struct initializers.
...
>   drivers/net/wireless/ath/ath5k/ahb.c                   |  8 ++++----

For the above:

Acked-by: Jiri Slaby <jirislaby at kernel.org>

-- 
js
suse labs


From kvalo at kernel.org  Mon Nov 11 04:10:58 2024
From: kvalo at kernel.org (Kalle Valo)
Date: Mon, 11 Nov 2024 12:10:58 +0000 (UTC)
Subject: [PATCH] wifi: Switch back to struct platform_driver::remove()
In-Reply-To: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
References: <20241106170706.38922-2-u.kleine-koenig@baylibre.com>
Message-ID: <173132705627.852485.14271331752921398347.kvalo@kernel.org>

Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com> wrote:

> After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
> return void") .remove() is (again) the right callback to implement for
> platform drivers.
> 
> Convert all platform drivers below drivers/net/wireless to use
> .remove(), with the eventual goal to drop struct
> platform_driver::remove_new(). As .remove() and .remove_new() have the
> same prototypes, conversion is done by just changing the structure
> member name in the driver initializer.
> 
> En passant several whitespace changes are done to make indentation
> consistent in the struct initializers.
> 
> Signed-off-by: Uwe Kleine-K?nig <u.kleine-koenig at baylibre.com>
> Acked-by: Jeff Johnson <quic_jjohnson at quicinc.com>
> Acked-by: Toke H?iland-J?rgensen <toke at toke.dk>
> Acked-by: Arend van Spriel <arend.vanspriel at broadcom.com>
> Acked-by: Jiri Slaby <jirislaby at kernel.org>

Patch applied to wireless-next.git, thanks.

b41f96ecb9b7 wifi: Switch back to struct platform_driver::remove()

-- 
https://patchwork.kernel.org/project/linux-wireless/patch/20241106170706.38922-2-u.kleine-koenig at baylibre.com/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches



From lech.perczak at gmail.com  Sat Nov 16 09:55:12 2024
From: lech.perczak at gmail.com (Lech Perczak)
Date: Sat, 16 Nov 2024 18:55:12 +0100
Subject: ath10k-firmware:: QCA9888 hw2.0: Add ZTE MF286A/R specific BDF
Message-ID: <b9154847-21d9-4081-9590-2cb718c68c2e@gmail.com>

Hello,

These (two) devices already works with OpenWrt, sharing the exact same
board design for the router part, differing only by the modem part.
However, after some time I discovered, that generic board data hampers its
RX performance. Replacing the BDF with one extracted from stock firmware
(same as for MF286C) caused about 60% increased throughput in iperf3 test
during reception, transmission being unaffected - with a QCA6174-based m.2
card as a link partner.
The throughput went up from around 240 to around 360Mbps.

Now to the questions from the wiki page [1]:

* description for what hardware this is:

- it is a QCA9563 based board
- QCA9563 is used for 2.4GHz (so out of concern for ath10k)
- QCA9888 is used for 5GHz band

* origin of the board file (did you create it yourself or where you
downloaded)

- Extracted from the vendor firmware by myself.

* ids to be used with the board file (ATH10K_BD_IE_BOARD_NAME in ath10k)

- QCA9888 hw2.0

+ bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=ZTE-MF286AR.bin
sha256sum:
9c7c97531479041f8197b9492b054d40e57fd92107b6986e447d360f1d914e92
* attach the actual board file (board.bin)

- The name of the file is equal to the id string in the board-2.bin
(minus the ".bin")

With kind regards,
Lech

[1]https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles

-------------- next part --------------
A non-text attachment was scrubbed...
Name: bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=ZTE-MF286AR.bin
Type: application/octet-stream
Size: 12064 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/ath10k/attachments/20241116/6fde5e06/attachment.bin>

From konrad.olkiewicz at revenueraft.com  Tue Nov 19 00:45:24 2024
From: konrad.olkiewicz at revenueraft.com (Konrad Olkiewicz)
Date: Tue, 19 Nov 2024 08:45:24 GMT
Subject: =?UTF-8?Q?Pytanie_o_ofert=C4=99?=
Message-ID: <20241119074501-0.1.3t.dgod.0.1m8u4jhofv@revenueraft.com>

Dzie? dobry,

Czy potrzebuj? Pa?stwo aktualnie nowych klient?w ?

Skutecznie pomagamy rozpoczyna? rozmowy handlowe z klientami zainteresowanymi Pa?stwa ofert?.

Zapraszam do kontaktu zwrotnego.


Pozdrawiam serdecznie
Konrad Olkiewicz


From repk at triplefau.lt  Fri Nov 22 08:48:00 2024
From: repk at triplefau.lt (Remi Pommarel)
Date: Fri, 22 Nov 2024 17:48:00 +0100
Subject: [RESEND PATCH v3 0/2] Improve ath10k flush queue mechanism
Message-ID: <cover.1732293922.git.repk@triplefau.lt>

It has been reported [0] that a 3-4 seconds (actually up to 5 sec) of
radio silence could be observed followed by the error below on ath10k
devices:

 ath10k_pci 0000:04:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0

This is due to how the TX queues are flushed in ath10k. When a STA is
removed, mac80211 need to flush queues [1], but because ath10k does not
have a lightweight .flush_sta operation, ieee80211_flush_queues() is
called instead effectively blocking the whole queue during the drain
causing this radio silence. Also because ath10k_flush() waits for all
queued to be emptied, not only the flushed ones it could more easily
take up to 5 seconds to finish making the whole situation worst.

The first patch of this series adds a .flush_sta operation to flush only
specific STA traffic avoiding the need to stop whole queues and should
be enough in itself to fix the reported issue.

The second patch of this series is a proposal to improve ath10k_flush so
that it will be less likely to timeout waiting for non related queues to
drain.

The abose kernel warning could still be observed (e.g. flushing a dead
STA) but should be now harmless.

[0]: https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
[1]: commit 0b75a1b1e42e ("wifi: mac80211: flush queues on STA removal")

V3:
  - Initialize empty to true to fix smatch error

V2:
  - Add Closes tag
  - Use atomic instead of spinlock for per sta pending frame counter
  - Call ath10k_htt_tx_sta_dec_pending within rcu
  - Rename pending_per_queue[] to num_pending_per_queue[]

Remi Pommarel (2):
  wifi: ath10k: Implement ieee80211 flush_sta callback
  wifi: ath10k: Flush only requested txq in ath10k_flush()

 drivers/net/wireless/ath/ath10k/core.h   |  2 +
 drivers/net/wireless/ath/ath10k/htt.h    | 11 +++-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 49 +++++++++++++++-
 drivers/net/wireless/ath/ath10k/mac.c    | 75 ++++++++++++++++++++----
 drivers/net/wireless/ath/ath10k/txrx.c   | 11 ++--
 5 files changed, 127 insertions(+), 21 deletions(-)

-- 
2.40.0



From repk at triplefau.lt  Fri Nov 22 08:48:02 2024
From: repk at triplefau.lt (Remi Pommarel)
Date: Fri, 22 Nov 2024 17:48:02 +0100
Subject: [RESEND PATCH v3 2/2] wifi: ath10k: Flush only requested txq in
 ath10k_flush()
In-Reply-To: <cover.1732293922.git.repk@triplefau.lt>
References: <cover.1732293922.git.repk@triplefau.lt>
Message-ID: <01d859e8e574a1f5d0b916333fe0b5cda859af9b.1732293922.git.repk@triplefau.lt>

The ieee80211 flush callback can be called to flush only part of all hw
queues. The ath10k's flush callback implementation (i.e. ath10k_flush())
was waiting for all pending frames of all queues to be flushed ignoring
the queue parameter. Because only the queues to be flushed are stopped
by mac80211, skb can still be queued to other queues meanwhile. Thus
ath10k_flush() could fail (and wait 5sec holding ar->conf lock) even if
the requested queues are flushed correctly.

A way to reproduce the issue is to use two different APs because
each vdev has its own hw queue in ath10k. Connect STA0 to AP0 and STA1
to AP1. Then generate traffic from AP0 to STA0 and kill STA0 without
clean disassociation frame (e.g. unplug power cable, reboot -f, ...).
Now if we were to flush AP1's queue, ath10k_flush() would fail (and
effectively block 5 seconds with ar->conf or even wiphy's lock held)
with the following warning:

 ath10k_pci 0000:01:00.0: failed to flush transmit queue (skip 0 ar-state 2): 0

Wait only for pending frames of the requested queues to be flushed in
ath10k_flush() to avoid that long blocking.

Reported-by: Cedric Veilleux <veilleux.cedric at gmail.com>
Closes: https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
Signed-off-by: Remi Pommarel <repk at triplefau.lt>
---
 drivers/net/wireless/ath/ath10k/htt.h    |  7 +++--
 drivers/net/wireless/ath/ath10k/htt_tx.c | 18 ++++++++++--
 drivers/net/wireless/ath/ath10k/mac.c    | 35 ++++++++++++++++--------
 drivers/net/wireless/ath/ath10k/txrx.c   |  2 +-
 4 files changed, 45 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index d150f9330941..ca8bf3b6766d 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1870,6 +1870,7 @@ struct ath10k_htt {
 	spinlock_t tx_lock;
 	int max_num_pending_tx;
 	int num_pending_tx;
+	int num_pending_per_queue[IEEE80211_MAX_QUEUES];
 	int num_pending_mgmt_tx;
 	struct idr pending_tx;
 	wait_queue_head_t empty_tx_wq;
@@ -2447,8 +2448,10 @@ void ath10k_htt_tx_txq_update(struct ieee80211_hw *hw,
 void ath10k_htt_tx_txq_recalc(struct ieee80211_hw *hw,
 			      struct ieee80211_txq *txq);
 void ath10k_htt_tx_txq_sync(struct ath10k *ar);
-void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt);
-int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt);
+void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt,
+			       struct ieee80211_txq *txq);
+int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt,
+			      struct ieee80211_txq *txq);
 void ath10k_htt_tx_mgmt_dec_pending(struct ath10k_htt *htt);
 int ath10k_htt_tx_mgmt_inc_pending(struct ath10k_htt *htt, bool is_mgmt,
 				   bool is_presp);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 211752bd0f65..ef5a992e8cce 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -140,19 +140,26 @@ void ath10k_htt_tx_txq_update(struct ieee80211_hw *hw,
 	spin_unlock_bh(&ar->htt.tx_lock);
 }
 
-void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt)
+void ath10k_htt_tx_dec_pending(struct ath10k_htt *htt,
+			       struct ieee80211_txq *txq)
 {
+	int qnr = -1;
+
 	lockdep_assert_held(&htt->tx_lock);
 
 	htt->num_pending_tx--;
 	if (htt->num_pending_tx == htt->max_num_pending_tx - 1)
 		ath10k_mac_tx_unlock(htt->ar, ATH10K_TX_PAUSE_Q_FULL);
 
-	if (htt->num_pending_tx == 0)
+	if (txq)
+		qnr = --htt->num_pending_per_queue[txq->vif->hw_queue[txq->ac]];
+
+	if (htt->num_pending_tx == 0 || qnr == 0)
 		wake_up(&htt->empty_tx_wq);
 }
 
-int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt)
+int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt,
+			      struct ieee80211_txq *txq)
 {
 	lockdep_assert_held(&htt->tx_lock);
 
@@ -163,6 +170,11 @@ int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt)
 	if (htt->num_pending_tx == htt->max_num_pending_tx)
 		ath10k_mac_tx_lock(htt->ar, ATH10K_TX_PAUSE_Q_FULL);
 
+	if (!txq)
+		return 0;
+
+	htt->num_pending_per_queue[txq->vif->hw_queue[txq->ac]]++;
+
 	return 0;
 }
 
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 8b8d4f24e5fb..7c5f95f2858f 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4385,7 +4385,7 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 	u16 airtime;
 
 	spin_lock_bh(&ar->htt.tx_lock);
-	ret = ath10k_htt_tx_inc_pending(htt);
+	ret = ath10k_htt_tx_inc_pending(htt, txq);
 	spin_unlock_bh(&ar->htt.tx_lock);
 
 	if (ret)
@@ -4394,7 +4394,7 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 	skb = ieee80211_tx_dequeue_ni(hw, txq);
 	if (!skb) {
 		spin_lock_bh(&ar->htt.tx_lock);
-		ath10k_htt_tx_dec_pending(htt);
+		ath10k_htt_tx_dec_pending(htt, txq);
 		spin_unlock_bh(&ar->htt.tx_lock);
 
 		return -ENOENT;
@@ -4416,7 +4416,7 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 		ret = ath10k_htt_tx_mgmt_inc_pending(htt, is_mgmt, is_presp);
 
 		if (ret) {
-			ath10k_htt_tx_dec_pending(htt);
+			ath10k_htt_tx_dec_pending(htt, txq);
 			spin_unlock_bh(&ar->htt.tx_lock);
 			return ret;
 		}
@@ -4430,7 +4430,7 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 		ath10k_warn(ar, "failed to push frame: %d\n", ret);
 
 		spin_lock_bh(&ar->htt.tx_lock);
-		ath10k_htt_tx_dec_pending(htt);
+		ath10k_htt_tx_dec_pending(htt, txq);
 		if (is_mgmt)
 			ath10k_htt_tx_mgmt_dec_pending(htt);
 		spin_unlock_bh(&ar->htt.tx_lock);
@@ -4693,7 +4693,7 @@ static void ath10k_mac_op_tx(struct ieee80211_hw *hw,
 			is_presp = ieee80211_is_probe_resp(hdr->frame_control);
 		}
 
-		ret = ath10k_htt_tx_inc_pending(htt);
+		ret = ath10k_htt_tx_inc_pending(htt, txq);
 		if (ret) {
 			ath10k_warn(ar, "failed to increase tx pending count: %d, dropping\n",
 				    ret);
@@ -4706,7 +4706,7 @@ static void ath10k_mac_op_tx(struct ieee80211_hw *hw,
 		if (ret) {
 			ath10k_dbg(ar, ATH10K_DBG_MAC, "failed to increase tx mgmt pending count: %d, dropping\n",
 				   ret);
-			ath10k_htt_tx_dec_pending(htt);
+			ath10k_htt_tx_dec_pending(htt, txq);
 			spin_unlock_bh(&ar->htt.tx_lock);
 			ieee80211_free_txskb(ar->hw, skb);
 			return;
@@ -4719,7 +4719,7 @@ static void ath10k_mac_op_tx(struct ieee80211_hw *hw,
 		ath10k_warn(ar, "failed to transmit frame: %d\n", ret);
 		if (is_htt) {
 			spin_lock_bh(&ar->htt.tx_lock);
-			ath10k_htt_tx_dec_pending(htt);
+			ath10k_htt_tx_dec_pending(htt, txq);
 			if (is_mgmt)
 				ath10k_htt_tx_mgmt_dec_pending(htt);
 			spin_unlock_bh(&ar->htt.tx_lock);
@@ -8059,10 +8059,12 @@ static int ath10k_mac_op_set_frag_threshold(struct ieee80211_hw *hw, u32 value)
 	return -EOPNOTSUPP;
 }
 
-void ath10k_mac_wait_tx_complete(struct ath10k *ar)
+static void _ath10k_mac_wait_tx_complete(struct ath10k *ar,
+					 unsigned long queues)
 {
 	bool skip;
 	long time_left;
+	unsigned int q;
 
 	/* mac80211 doesn't care if we really xmit queued frames or not
 	 * we'll collect those frames either way if we stop/delete vdevs
@@ -8072,10 +8074,14 @@ void ath10k_mac_wait_tx_complete(struct ath10k *ar)
 		return;
 
 	time_left = wait_event_timeout(ar->htt.empty_tx_wq, ({
-			bool empty;
+			bool empty = true;
 
 			spin_lock_bh(&ar->htt.tx_lock);
-			empty = (ar->htt.num_pending_tx == 0);
+			for_each_set_bit(q, &queues, ar->hw->queues) {
+				empty = (ar->htt.num_pending_per_queue[q] == 0);
+				if (!empty)
+					break;
+			}
 			spin_unlock_bh(&ar->htt.tx_lock);
 
 			skip = (ar->state == ATH10K_STATE_WEDGED) ||
@@ -8090,6 +8096,13 @@ void ath10k_mac_wait_tx_complete(struct ath10k *ar)
 			    skip, ar->state, time_left);
 }
 
+void ath10k_mac_wait_tx_complete(struct ath10k *ar)
+{
+	unsigned int queues = GENMASK(ar->hw->queues - 1, 0);
+
+	_ath10k_mac_wait_tx_complete(ar, queues);
+}
+
 static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 			 u32 queues, bool drop)
 {
@@ -8111,7 +8124,7 @@ static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 	}
 
 	mutex_lock(&ar->conf_mutex);
-	ath10k_mac_wait_tx_complete(ar);
+	_ath10k_mac_wait_tx_complete(ar, queues);
 	mutex_unlock(&ar->conf_mutex);
 }
 
diff --git a/drivers/net/wireless/ath/ath10k/txrx.c b/drivers/net/wireless/ath/ath10k/txrx.c
index 5b6750ef7d19..b848962fc8fb 100644
--- a/drivers/net/wireless/ath/ath10k/txrx.c
+++ b/drivers/net/wireless/ath/ath10k/txrx.c
@@ -82,7 +82,7 @@ int ath10k_txrx_tx_unref(struct ath10k_htt *htt,
 
 	flags = skb_cb->flags;
 	ath10k_htt_tx_free_msdu_id(htt, tx_done->msdu_id);
-	ath10k_htt_tx_dec_pending(htt);
+	ath10k_htt_tx_dec_pending(htt, txq);
 	spin_unlock_bh(&htt->tx_lock);
 
 	rcu_read_lock();
-- 
2.40.0



From repk at triplefau.lt  Fri Nov 22 08:48:01 2024
From: repk at triplefau.lt (Remi Pommarel)
Date: Fri, 22 Nov 2024 17:48:01 +0100
Subject: [RESEND PATCH v3 1/2] wifi: ath10k: Implement ieee80211 flush_sta
 callback
In-Reply-To: <cover.1732293922.git.repk@triplefau.lt>
References: <cover.1732293922.git.repk@triplefau.lt>
Message-ID: <17d26d6a3e80ff03939ee7935fdc07f979b61a4f.1732293922.git.repk@triplefau.lt>

When a STA reassociates, mac80211's _sta_info_move_state() waits for all
pending frame to be flushed before removing the key (so that no frame
get sent unencrypted after key removable [0]). When a driver does not
implement the flush_sta callback, ieee80211_flush_queues() is called
instead which effectively stops the whole queue until it is completely
drained.

The ath10k driver configure all STAs of one vdev to share the same
queue. So when flushing one STA this is the whole vdev queue that is
blocked until completely drained causing Tx to other STA to also stall
this whole time.

One easy way to reproduce the issue is to connect two STAs (STA0 and
STA1) to an ath10k AP. While Generating a bunch of traffic from AP to
STA0 (e.g. fping -l -p 20 <STA0-IP>) disconnect STA0 from AP without
clean disassociation (e.g. remove power, reboot -f). Then as soon as
STA0 is effectively disconnected from AP (either after inactivity
timeout or forced with iw dev AP station del STA0), its queues get
flushed using ieee80211_flush_queues(). This causes STA1 to suffer a
connectivity stall for about 5 seconds (see ATH10K_FLUSH_TIMEOUT_HZ).

Implement a flush_sta callback in ath10k to wait only for a specific
STA pending frames to be drained (without stopping the whole HW queue)
to fix that.

[0]: commit 0b75a1b1e42e ("wifi: mac80211: flush queues on STA removal")

Reported-by: Cedric Veilleux <veilleux.cedric at gmail.com>
Closes: https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
Signed-off-by: Remi Pommarel <repk at triplefau.lt>
---
 drivers/net/wireless/ath/ath10k/core.h   |  2 ++
 drivers/net/wireless/ath/ath10k/htt.h    |  4 +++
 drivers/net/wireless/ath/ath10k/htt_tx.c | 31 ++++++++++++++++++
 drivers/net/wireless/ath/ath10k/mac.c    | 40 +++++++++++++++++++++++-
 drivers/net/wireless/ath/ath10k/txrx.c   |  9 ++++--
 5 files changed, 82 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 446dca74f06a..4ec2faa055c0 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -558,6 +558,8 @@ struct ath10k_sta {
 	u8 rate_ctrl[ATH10K_TID_MAX];
 	u32 rate_code[ATH10K_TID_MAX];
 	int rtscts[ATH10K_TID_MAX];
+	wait_queue_head_t empty_tx_wq;
+	atomic_t num_fw_queued;
 };
 
 #define ATH10K_VDEV_SETUP_TIMEOUT_HZ	(5 * HZ)
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 603f6de62b0a..d150f9330941 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -2452,6 +2452,10 @@ int ath10k_htt_tx_inc_pending(struct ath10k_htt *htt);
 void ath10k_htt_tx_mgmt_dec_pending(struct ath10k_htt *htt);
 int ath10k_htt_tx_mgmt_inc_pending(struct ath10k_htt *htt, bool is_mgmt,
 				   bool is_presp);
+void ath10k_htt_tx_sta_inc_pending(struct ath10k_htt *htt,
+				   struct ieee80211_sta *sta);
+void ath10k_htt_tx_sta_dec_pending(struct ath10k_htt *htt,
+				   struct ieee80211_sta *sta);
 
 int ath10k_htt_tx_alloc_msdu_id(struct ath10k_htt *htt, struct sk_buff *skb);
 void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 9725feecefd6..211752bd0f65 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -195,6 +195,37 @@ void ath10k_htt_tx_mgmt_dec_pending(struct ath10k_htt *htt)
 	htt->num_pending_mgmt_tx--;
 }
 
+void ath10k_htt_tx_sta_inc_pending(struct ath10k_htt *htt,
+				   struct ieee80211_sta *sta)
+{
+	struct ath10k_sta *arsta;
+
+	if (!sta)
+		return;
+
+	arsta = (struct ath10k_sta *)sta->drv_priv;
+
+	atomic_inc(&arsta->num_fw_queued);
+}
+
+void ath10k_htt_tx_sta_dec_pending(struct ath10k_htt *htt,
+				   struct ieee80211_sta *sta)
+{
+	struct ath10k_sta *arsta;
+	int v;
+
+	if (!sta)
+		return;
+
+	arsta = (struct ath10k_sta *)sta->drv_priv;
+
+	v = atomic_dec_if_positive(&arsta->num_fw_queued);
+	if (v < 0)
+		WARN_ON_ONCE(1);
+	if (v == 0)
+		wake_up(&arsta->empty_tx_wq);
+}
+
 int ath10k_htt_tx_alloc_msdu_id(struct ath10k_htt *htt, struct sk_buff *skb)
 {
 	struct ath10k *ar = htt->ar;
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index c61b95a928da..8b8d4f24e5fb 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -4423,6 +4423,8 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 		spin_unlock_bh(&ar->htt.tx_lock);
 	}
 
+	ath10k_htt_tx_sta_inc_pending(&ar->htt, sta);
+
 	ret = ath10k_mac_tx(ar, vif, txmode, txpath, skb, false);
 	if (unlikely(ret)) {
 		ath10k_warn(ar, "failed to push frame: %d\n", ret);
@@ -4432,6 +4434,7 @@ int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw,
 		if (is_mgmt)
 			ath10k_htt_tx_mgmt_dec_pending(htt);
 		spin_unlock_bh(&ar->htt.tx_lock);
+		ath10k_htt_tx_sta_dec_pending(&ar->htt, sta);
 
 		return ret;
 	}
@@ -7481,7 +7484,7 @@ static int ath10k_sta_state(struct ieee80211_hw *hw,
 		arsta->peer_ps_state = WMI_PEER_PS_STATE_DISABLED;
 		INIT_WORK(&arsta->update_wk, ath10k_sta_rc_update_wk);
 		INIT_WORK(&arsta->tid_config_wk, ath10k_sta_tid_cfg_wk);
-
+		init_waitqueue_head(&arsta->empty_tx_wq);
 		for (i = 0; i < ARRAY_SIZE(sta->txq); i++)
 			ath10k_mac_txq_init(sta->txq[i]);
 	}
@@ -8112,6 +8115,40 @@ static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 	mutex_unlock(&ar->conf_mutex);
 }
 
+static void ath10k_flush_sta(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+			     struct ieee80211_sta *sta)
+{
+	struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv;
+	struct ath10k *ar = hw->priv;
+	bool skip;
+	long time_left;
+
+	/* TODO do we need drop implemented here ? */
+
+	mutex_lock(&ar->conf_mutex);
+
+	if (ar->state == ATH10K_STATE_WEDGED)
+		goto out;
+
+	time_left = wait_event_timeout(arsta->empty_tx_wq, ({
+			bool empty;
+
+			empty = atomic_read(&arsta->num_fw_queued) == 0;
+
+			skip = (ar->state == ATH10K_STATE_WEDGED) ||
+			       test_bit(ATH10K_FLAG_CRASH_FLUSH,
+					&ar->dev_flags);
+
+			(empty || skip);
+		}), ATH10K_FLUSH_TIMEOUT_HZ);
+
+	if (time_left == 0 || skip)
+		ath10k_warn(ar, "failed to flush sta txq (sta %pM skip %i ar-state %i): %ld\n",
+			    sta->addr, skip, ar->state, time_left);
+out:
+	mutex_unlock(&ar->conf_mutex);
+}
+
 /* TODO: Implement this function properly
  * For now it is needed to reply to Probe Requests in IBSS mode.
  * Probably we need this information from FW.
@@ -9459,6 +9496,7 @@ static const struct ieee80211_ops ath10k_ops = {
 	.set_rts_threshold		= ath10k_set_rts_threshold,
 	.set_frag_threshold		= ath10k_mac_op_set_frag_threshold,
 	.flush				= ath10k_flush,
+	.flush_sta			= ath10k_flush_sta,
 	.tx_last_beacon			= ath10k_tx_last_beacon,
 	.set_antenna			= ath10k_set_antenna,
 	.get_antenna			= ath10k_get_antenna,
diff --git a/drivers/net/wireless/ath/ath10k/txrx.c b/drivers/net/wireless/ath/ath10k/txrx.c
index da3bc35e41aa..5b6750ef7d19 100644
--- a/drivers/net/wireless/ath/ath10k/txrx.c
+++ b/drivers/net/wireless/ath/ath10k/txrx.c
@@ -86,9 +86,12 @@ int ath10k_txrx_tx_unref(struct ath10k_htt *htt,
 	spin_unlock_bh(&htt->tx_lock);
 
 	rcu_read_lock();
-	if (txq && txq->sta && skb_cb->airtime_est)
-		ieee80211_sta_register_airtime(txq->sta, txq->tid,
-					       skb_cb->airtime_est, 0);
+	if (txq && txq->sta) {
+		if (skb_cb->airtime_est)
+			ieee80211_sta_register_airtime(txq->sta, txq->tid,
+						       skb_cb->airtime_est, 0);
+		ath10k_htt_tx_sta_dec_pending(htt, txq->sta);
+	}
 	rcu_read_unlock();
 
 	if (ar->bus_param.dev_type != ATH10K_DEV_TYPE_HL)
-- 
2.40.0



From sashal at kernel.org  Sun Nov 24 05:29:05 2024
From: sashal at kernel.org (Sasha Levin)
Date: Sun, 24 Nov 2024 08:29:05 -0500
Subject: [PATCH AUTOSEL 6.12 045/107] wifi: ath10k: avoid NULL pointer error during sdio remove
In-Reply-To: <20241124133301.3341829-1-sashal@kernel.org>
References: <20241124133301.3341829-1-sashal@kernel.org>
Message-ID: <20241124133301.3341829-45-sashal@kernel.org>

From: Kang Yang <quic_kangyang at quicinc.com>

[ Upstream commit 95c38953cb1ecf40399a676a1f85dfe2b5780a9a ]

When running 'rmmod ath10k', ath10k_sdio_remove() will free sdio
workqueue by destroy_workqueue(). But if CONFIG_INIT_ON_FREE_DEFAULT_ON
is set to yes, kernel panic will happen:
Call trace:
 destroy_workqueue+0x1c/0x258
 ath10k_sdio_remove+0x84/0x94
 sdio_bus_remove+0x50/0x16c
 device_release_driver_internal+0x188/0x25c
 device_driver_detach+0x20/0x2c

This is because during 'rmmod ath10k', ath10k_sdio_remove() will call
ath10k_core_destroy() before destroy_workqueue(). wiphy_dev_release()
will finally be called in ath10k_core_destroy(). This function will free
struct cfg80211_registered_device *rdev and all its members, including
wiphy, dev and the pointer of sdio workqueue. Then the pointer of sdio
workqueue will be set to NULL due to CONFIG_INIT_ON_FREE_DEFAULT_ON.

After device release, destroy_workqueue() will use NULL pointer then the
kernel panic happen.

Call trace:
ath10k_sdio_remove
  ->ath10k_core_unregister
    ??
    ->ath10k_core_stop
      ->ath10k_hif_stop
        ->ath10k_sdio_irq_disable
    ->ath10k_hif_power_down
      ->del_timer_sync(&ar_sdio->sleep_timer)
  ->ath10k_core_destroy
    ->ath10k_mac_destroy
      ->ieee80211_free_hw
        ->wiphy_free
    ??
          ->wiphy_dev_release
  ->destroy_workqueue

Need to call destroy_workqueue() before ath10k_core_destroy(), free
the work queue buffer first and then free pointer of work queue by
ath10k_core_destroy(). This order matches the error path order in
ath10k_sdio_probe().

No work will be queued on sdio workqueue between it is destroyed and
ath10k_core_destroy() is called. Based on the call_stack above, the
reason is:
Only ath10k_sdio_sleep_timer_handler(), ath10k_sdio_hif_tx_sg() and
ath10k_sdio_irq_disable() will queue work on sdio workqueue.
Sleep timer will be deleted before ath10k_core_destroy() in
ath10k_hif_power_down().
ath10k_sdio_irq_disable() only be called in ath10k_hif_stop().
ath10k_core_unregister() will call ath10k_hif_power_down() to stop hif
bus, so ath10k_sdio_hif_tx_sg() won't be called anymore.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189

Signed-off-by: Kang Yang <quic_kangyang at quicinc.com>
Tested-by: David Ruth <druth at chromium.org>
Reviewed-by: David Ruth <druth at chromium.org>
Link: https://patch.msgid.link/20241008022246.1010-1-quic_kangyang at quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson at quicinc.com>
Signed-off-by: Sasha Levin <sashal at kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index 08a6f36a6be9c..6805357ee29e6 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -3,7 +3,7 @@
  * Copyright (c) 2004-2011 Atheros Communications Inc.
  * Copyright (c) 2011-2012,2017 Qualcomm Atheros, Inc.
  * Copyright (c) 2016-2017 Erik Stromdahl <erik.stromdahl at gmail.com>
- * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <linux/module.h>
@@ -2648,9 +2648,9 @@ static void ath10k_sdio_remove(struct sdio_func *func)
 
 	netif_napi_del(&ar->napi);
 
-	ath10k_core_destroy(ar);
-
 	destroy_workqueue(ar_sdio->workqueue);
+
+	ath10k_core_destroy(ar);
 }
 
 static const struct sdio_device_id ath10k_sdio_devices[] = {
-- 
2.43.0



From sashal at kernel.org  Sun Nov 24 05:38:17 2024
From: sashal at kernel.org (Sasha Levin)
Date: Sun, 24 Nov 2024 08:38:17 -0500
Subject: [PATCH AUTOSEL 6.11 39/87] wifi: ath10k: avoid NULL pointer error during sdio remove
In-Reply-To: <20241124134102.3344326-1-sashal@kernel.org>
References: <20241124134102.3344326-1-sashal@kernel.org>
Message-ID: <20241124134102.3344326-39-sashal@kernel.org>

From: Kang Yang <quic_kangyang at quicinc.com>

[ Upstream commit 95c38953cb1ecf40399a676a1f85dfe2b5780a9a ]

When running 'rmmod ath10k', ath10k_sdio_remove() will free sdio
workqueue by destroy_workqueue(). But if CONFIG_INIT_ON_FREE_DEFAULT_ON
is set to yes, kernel panic will happen:
Call trace:
 destroy_workqueue+0x1c/0x258
 ath10k_sdio_remove+0x84/0x94
 sdio_bus_remove+0x50/0x16c
 device_release_driver_internal+0x188/0x25c
 device_driver_detach+0x20/0x2c

This is because during 'rmmod ath10k', ath10k_sdio_remove() will call
ath10k_core_destroy() before destroy_workqueue(). wiphy_dev_release()
will finally be called in ath10k_core_destroy(). This function will free
struct cfg80211_registered_device *rdev and all its members, including
wiphy, dev and the pointer of sdio workqueue. Then the pointer of sdio
workqueue will be set to NULL due to CONFIG_INIT_ON_FREE_DEFAULT_ON.

After device release, destroy_workqueue() will use NULL pointer then the
kernel panic happen.

Call trace:
ath10k_sdio_remove
  ->ath10k_core_unregister
    ??
    ->ath10k_core_stop
      ->ath10k_hif_stop
        ->ath10k_sdio_irq_disable
    ->ath10k_hif_power_down
      ->del_timer_sync(&ar_sdio->sleep_timer)
  ->ath10k_core_destroy
    ->ath10k_mac_destroy
      ->ieee80211_free_hw
        ->wiphy_free
    ??
          ->wiphy_dev_release
  ->destroy_workqueue

Need to call destroy_workqueue() before ath10k_core_destroy(), free
the work queue buffer first and then free pointer of work queue by
ath10k_core_destroy(). This order matches the error path order in
ath10k_sdio_probe().

No work will be queued on sdio workqueue between it is destroyed and
ath10k_core_destroy() is called. Based on the call_stack above, the
reason is:
Only ath10k_sdio_sleep_timer_handler(), ath10k_sdio_hif_tx_sg() and
ath10k_sdio_irq_disable() will queue work on sdio workqueue.
Sleep timer will be deleted before ath10k_core_destroy() in
ath10k_hif_power_down().
ath10k_sdio_irq_disable() only be called in ath10k_hif_stop().
ath10k_core_unregister() will call ath10k_hif_power_down() to stop hif
bus, so ath10k_sdio_hif_tx_sg() won't be called anymore.

Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189

Signed-off-by: Kang Yang <quic_kangyang at quicinc.com>
Tested-by: David Ruth <druth at chromium.org>
Reviewed-by: David Ruth <druth at chromium.org>
Link: https://patch.msgid.link/20241008022246.1010-1-quic_kangyang at quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson at quicinc.com>
Signed-off-by: Sasha Levin <sashal at kernel.org>
---
 drivers/net/wireless/ath/ath10k/sdio.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/sdio.c b/drivers/net/wireless/ath/ath10k/sdio.c
index 08a6f36a6be9c..6805357ee29e6 100644
--- a/drivers/net/wireless/ath/ath10k/sdio.c
+++ b/drivers/net/wireless/ath/ath10k/sdio.c
@@ -3,7 +3,7 @@
  * Copyright (c) 2004-2011 Atheros Communications Inc.
  * Copyright (c) 2011-2012,2017 Qualcomm Atheros, Inc.
  * Copyright (c) 2016-2017 Erik Stromdahl <erik.stromdahl at gmail.com>
- * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2022-2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
 #include <linux/module.h>
@@ -2648,9 +2648,9 @@ static void ath10k_sdio_remove(struct sdio_func *func)
 
 	netif_napi_del(&ar->napi);
 
-	ath10k_core_destroy(ar);
-
 	destroy_workqueue(ar_sdio->workqueue);
+
+	ath10k_core_destroy(ar);
 }
 
 static const struct sdio_device_id ath10k_sdio_devices[] = {
-- 
2.43.0



From prestwoj at gmail.com  Mon Nov 25 05:32:06 2024
From: prestwoj at gmail.com (James Prestwood)
Date: Mon, 25 Nov 2024 05:32:06 -0800
Subject: ath10k "failed to install key for vdev 0 peer <mac>: -110"
In-Reply-To: <dda85730-3f19-490e-bb0f-99b13511c062@quicinc.com>
References: <e780560a-86eb-4189-ab5d-3bed3ee5825e@gmail.com>
 <54fac081-7d70-4d31-9f2a-07f5d75d675d@quicinc.com>
 <ea2e7c62-f6e9-4cba-ae81-19fc9abed8b7@gmail.com>
 <22978701-ca79-4e90-8ceb-16bdaf230e8f@quicinc.com>
 <dda85730-3f19-490e-bb0f-99b13511c062@quicinc.com>
Message-ID: <87c9bf22-9534-4292-bf9f-013cc710a3bc@gmail.com>

Hi Baochen,

On 9/4/24 6:46 PM, Baochen Qiang wrote:
>
> On 9/5/2024 2:03 AM, Jeff Johnson wrote:
>> On 8/16/2024 5:04 AM, James Prestwood wrote:
>>> Hi Baochen,
>>>
>>> On 8/16/24 3:19 AM, Baochen Qiang wrote:
>>>> On 7/12/2024 9:11 PM, James Prestwood wrote:
>>>>> Hi,
>>>>>
>>>>> I've seen this error mentioned on random forum posts, but its always associated with a kernel crash/warning or some very obvious negative behavior. I've noticed this occasionally and at one location very frequently during FT roaming, specifically just after CMD_ASSOCIATE is issued. For our company run networks I'm not seeing any negative behavior apart from a 3 second delay in sending the re-association frame since the kernel waits for this timeout. But we have some networks our clients run on that we do not own (different vendor), and we are seeing association timeouts after this error occurs and in some cases the AP is sending a deauthentication with reason code 8 instead of replying with a reassociation reply and an error status, which is quite odd.
>>>>>
>>>>> We are chasing down this with the vendor of these APs as well, but the behavior always happens after we see this key removal failure/timeout on the client side. So it would appear there is potentially a problem on both the client and AP. My guess is _something_ about the re-association frame changes when this error is encountered, but I cannot see how that would be the case. We are working to get PCAPs now, but its through a 3rd party, so that timing is out of my control.
>>>>>
>>>>>   From the kernel code this error would appear innocuous, the old key is failing to be removed but it gets immediately replaced by the new key. And we don't see that addition failing. Am I understanding that logic correctly? I.e. this logic:
>>>>>
>>>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/net/mac80211/key.c#n503
>>>>>
>>>>> Below are a few kernel logs of the issue happening, some with the deauth being sent by the AP, some with just timeouts:
>>>>>
>>>>> --- No deauth frame sent, just association timeouts after the error ---
>>>>>
>>>>> Jul 11 00:05:30 kernel: wlan0: disconnect from AP <previous BSS> for new assoc to <new BSS>
>>>>> Jul 11 00:05:33 kernel: ath10k_pci 0000:02:00.0: failed to install key for vdev 0 peer?<previous BSS>: -110
>>>>> Jul 11 00:05:33 kernel: wlan0: failed to remove key (0,?<previous BSS>) from hardware (-110)
>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 1/3)
>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 2/3)
>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 3/3)
>>>>> Jul 11 00:05:33 kernel: wlan0: association with?<new BSS> timed out
>>>>> Jul 11 00:05:36 kernel: wlan0: authenticate with <new BSS>
>>>>> Jul 11 00:05:36 kernel: wlan0: send auth to?<new BSS>a (try 1/3)
>>>>> Jul 11 00:05:36 kernel: wlan0: authenticated
>>>>> Jul 11 00:05:36 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>> Jul 11 00:05:36 kernel: wlan0: RX AssocResp from?<new BSS> (capab=0x1111 status=0 aid=16)
>>>>> Jul 11 00:05:36 kernel: wlan0: associated
>>>>>
>>>>> --- Deauth frame sent amidst the association timeouts ---
>>>>>
>>>>> Jul 11 00:43:18 kernel: wlan0: disconnect from AP <previous BSS> for new assoc to <new BSS>
>>>>> Jul 11 00:43:21 kernel: ath10k_pci 0000:02:00.0: failed to install key for vdev 0 peer <previous BSS>: -110
>>>>> Jul 11 00:43:21 kernel: wlan0: failed to remove key (0, <previous BSS>) from hardware (-110)
>>>>> Jul 11 00:43:21 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>> Jul 11 00:43:21 kernel: wlan0: deauthenticated from <new BSS> while associating (Reason: 8=DISASSOC_STA_HAS_LEFT)
>>>>> Jul 11 00:43:24 kernel: wlan0: authenticate with <new BSS>
>>>>> Jul 11 00:43:24 kernel: wlan0: send auth to <new BSS> (try 1/3)
>>>>> Jul 11 00:43:24 kernel: wlan0: authenticated
>>>>> Jul 11 00:43:24 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>> Jul 11 00:43:24 kernel: wlan0: RX AssocResp from <new BSS> (capab=0x1111 status=0 aid=101)
>>>>> Jul 11 00:43:24 kernel: wlan0: associated
>>>>>
>>>> Hi James, this is QCA6174, right? could you also share firmware version?
>>> Yep, using:
>>>
>>> qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1dac:0261
>>> firmware ver WLAN.RM.4.4.1-00288- api 6 features wowlan,ignore-otp,mfp
>>> crc32 bf907c7c
>>>
>>> I did try in one instance the latest firmware, 309, and still saw the
>>> same behavior but 288 is what all our devices are running.
>>>
>>> Thanks,
>>>
>>> James
>> Baochen, are you looking more into this? Would prefer to fix the root cause
>> rather than take "[RFC 0/1] wifi: ath10k: improvement on key removal failure"
> I asked CST team to try to reproduce this issue such that we can get firmware dump for debug further. What I got is that CST team is currently busy at other critical schedules and they are planning to debug this ath10k issue after those schedules get finished.

Any movement on this front? We are still carrying that RFC patch to work 
around the associated compatibility issues with Cisco APs when this 
timeout occurs.

While I do agree the RFC patch isn't optimal, trying to get a firmware 
fix for ~6 year old hardware also may not be very easy. fwiw we've been 
running the RFC patch for about 3 months now, as of today its running on 
over 4000 client devices. So IMO the patch itself is safe if there was 
any concern.

Thanks,

James



From quic_bqiang at quicinc.com  Mon Nov 25 18:56:06 2024
From: quic_bqiang at quicinc.com (Baochen Qiang)
Date: Tue, 26 Nov 2024 10:56:06 +0800
Subject: ath10k "failed to install key for vdev 0 peer <mac>: -110"
In-Reply-To: <87c9bf22-9534-4292-bf9f-013cc710a3bc@gmail.com>
References: <e780560a-86eb-4189-ab5d-3bed3ee5825e@gmail.com>
 <54fac081-7d70-4d31-9f2a-07f5d75d675d@quicinc.com>
 <ea2e7c62-f6e9-4cba-ae81-19fc9abed8b7@gmail.com>
 <22978701-ca79-4e90-8ceb-16bdaf230e8f@quicinc.com>
 <dda85730-3f19-490e-bb0f-99b13511c062@quicinc.com>
 <87c9bf22-9534-4292-bf9f-013cc710a3bc@gmail.com>
Message-ID: <90e546e0-80c8-4925-9711-a6091fa1a625@quicinc.com>



On 11/25/2024 9:32 PM, James Prestwood wrote:
> Hi Baochen,
> 
> On 9/4/24 6:46 PM, Baochen Qiang wrote:
>>
>> On 9/5/2024 2:03 AM, Jeff Johnson wrote:
>>> On 8/16/2024 5:04 AM, James Prestwood wrote:
>>>> Hi Baochen,
>>>>
>>>> On 8/16/24 3:19 AM, Baochen Qiang wrote:
>>>>> On 7/12/2024 9:11 PM, James Prestwood wrote:
>>>>>> Hi,
>>>>>>
>>>>>> I've seen this error mentioned on random forum posts, but its always associated with
>>>>>> a kernel crash/warning or some very obvious negative behavior. I've noticed this
>>>>>> occasionally and at one location very frequently during FT roaming, specifically
>>>>>> just after CMD_ASSOCIATE is issued. For our company run networks I'm not seeing any
>>>>>> negative behavior apart from a 3 second delay in sending the re-association frame
>>>>>> since the kernel waits for this timeout. But we have some networks our clients run
>>>>>> on that we do not own (different vendor), and we are seeing association timeouts
>>>>>> after this error occurs and in some cases the AP is sending a deauthentication with
>>>>>> reason code 8 instead of replying with a reassociation reply and an error status,
>>>>>> which is quite odd.
>>>>>>
>>>>>> We are chasing down this with the vendor of these APs as well, but the behavior
>>>>>> always happens after we see this key removal failure/timeout on the client side. So
>>>>>> it would appear there is potentially a problem on both the client and AP. My guess
>>>>>> is _something_ about the re-association frame changes when this error is
>>>>>> encountered, but I cannot see how that would be the case. We are working to get
>>>>>> PCAPs now, but its through a 3rd party, so that timing is out of my control.
>>>>>>
>>>>>> ? From the kernel code this error would appear innocuous, the old key is failing to
>>>>>> be removed but it gets immediately replaced by the new key. And we don't see that
>>>>>> addition failing. Am I understanding that logic correctly? I.e. this logic:
>>>>>>
>>>>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/net/
>>>>>> mac80211/key.c#n503
>>>>>>
>>>>>> Below are a few kernel logs of the issue happening, some with the deauth being sent
>>>>>> by the AP, some with just timeouts:
>>>>>>
>>>>>> --- No deauth frame sent, just association timeouts after the error ---
>>>>>>
>>>>>> Jul 11 00:05:30 kernel: wlan0: disconnect from AP <previous BSS> for new assoc to
>>>>>> <new BSS>
>>>>>> Jul 11 00:05:33 kernel: ath10k_pci 0000:02:00.0: failed to install key for vdev 0
>>>>>> peer?<previous BSS>: -110
>>>>>> Jul 11 00:05:33 kernel: wlan0: failed to remove key (0,?<previous BSS>) from
>>>>>> hardware (-110)
>>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 1/3)
>>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 2/3)
>>>>>> Jul 11 00:05:33 kernel: wlan0: associate with?<new BSS> (try 3/3)
>>>>>> Jul 11 00:05:33 kernel: wlan0: association with?<new BSS> timed out
>>>>>> Jul 11 00:05:36 kernel: wlan0: authenticate with <new BSS>
>>>>>> Jul 11 00:05:36 kernel: wlan0: send auth to?<new BSS>a (try 1/3)
>>>>>> Jul 11 00:05:36 kernel: wlan0: authenticated
>>>>>> Jul 11 00:05:36 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>>> Jul 11 00:05:36 kernel: wlan0: RX AssocResp from?<new BSS> (capab=0x1111 status=0
>>>>>> aid=16)
>>>>>> Jul 11 00:05:36 kernel: wlan0: associated
>>>>>>
>>>>>> --- Deauth frame sent amidst the association timeouts ---
>>>>>>
>>>>>> Jul 11 00:43:18 kernel: wlan0: disconnect from AP <previous BSS> for new assoc to
>>>>>> <new BSS>
>>>>>> Jul 11 00:43:21 kernel: ath10k_pci 0000:02:00.0: failed to install key for vdev 0
>>>>>> peer <previous BSS>: -110
>>>>>> Jul 11 00:43:21 kernel: wlan0: failed to remove key (0, <previous BSS>) from
>>>>>> hardware (-110)
>>>>>> Jul 11 00:43:21 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>>> Jul 11 00:43:21 kernel: wlan0: deauthenticated from <new BSS> while associating
>>>>>> (Reason: 8=DISASSOC_STA_HAS_LEFT)
>>>>>> Jul 11 00:43:24 kernel: wlan0: authenticate with <new BSS>
>>>>>> Jul 11 00:43:24 kernel: wlan0: send auth to <new BSS> (try 1/3)
>>>>>> Jul 11 00:43:24 kernel: wlan0: authenticated
>>>>>> Jul 11 00:43:24 kernel: wlan0: associate with <new BSS> (try 1/3)
>>>>>> Jul 11 00:43:24 kernel: wlan0: RX AssocResp from <new BSS> (capab=0x1111 status=0
>>>>>> aid=101)
>>>>>> Jul 11 00:43:24 kernel: wlan0: associated
>>>>>>
>>>>> Hi James, this is QCA6174, right? could you also share firmware version?
>>>> Yep, using:
>>>>
>>>> qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1dac:0261
>>>> firmware ver WLAN.RM.4.4.1-00288- api 6 features wowlan,ignore-otp,mfp
>>>> crc32 bf907c7c
>>>>
>>>> I did try in one instance the latest firmware, 309, and still saw the
>>>> same behavior but 288 is what all our devices are running.
>>>>
>>>> Thanks,
>>>>
>>>> James
>>> Baochen, are you looking more into this? Would prefer to fix the root cause
>>> rather than take "[RFC 0/1] wifi: ath10k: improvement on key removal failure"
>> I asked CST team to try to reproduce this issue such that we can get firmware dump for
>> debug further. What I got is that CST team is currently busy at other critical schedules
>> and they are planning to debug this ath10k issue after those schedules get finished.
> 
> Any movement on this front? We are still carrying that RFC patch to work around the
> associated compatibility issues with Cisco APs when this timeout occurs.
I ask the test team again, the response is that hopefully they can get bandwidth next week.

> 
> While I do agree the RFC patch isn't optimal, trying to get a firmware fix for ~6 year old
> hardware also may not be very easy. fwiw we've been running the RFC patch for about 3
> months now, as of today its running on over 4000 client devices. So IMO the patch itself
> is safe if there was any concern.
thanks for the info.

> 
> Thanks,
> 
> James
> 



From prestwoj at gmail.com  Tue Nov 26 04:57:36 2024
From: prestwoj at gmail.com (James Prestwood)
Date: Tue, 26 Nov 2024 04:57:36 -0800
Subject: [RESEND PATCH v3 0/2] Improve ath10k flush queue mechanism
In-Reply-To: <cover.1732293922.git.repk@triplefau.lt>
References: <cover.1732293922.git.repk@triplefau.lt>
Message-ID: <20215f63-e2e6-4f9a-bbbe-d7535c5ce9d2@gmail.com>

Hi Remi,

On 11/22/24 8:48 AM, Remi Pommarel wrote:
> It has been reported [0] that a 3-4 seconds (actually up to 5 sec) of
> radio silence could be observed followed by the error below on ath10k
> devices:
>
>   ath10k_pci 0000:04:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
>
> This is due to how the TX queues are flushed in ath10k. When a STA is
> removed, mac80211 need to flush queues [1], but because ath10k does not
> have a lightweight .flush_sta operation, ieee80211_flush_queues() is
> called instead effectively blocking the whole queue during the drain
> causing this radio silence. Also because ath10k_flush() waits for all
> queued to be emptied, not only the flushed ones it could more easily
> take up to 5 seconds to finish making the whole situation worst.
>
> The first patch of this series adds a .flush_sta operation to flush only
> specific STA traffic avoiding the need to stop whole queues and should
> be enough in itself to fix the reported issue.
>
> The second patch of this series is a proposal to improve ath10k_flush so
> that it will be less likely to timeout waiting for non related queues to
> drain.
>
> The abose kernel warning could still be observed (e.g. flushing a dead
> STA) but should be now harmless.
>
> [0]: https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
> [1]: commit 0b75a1b1e42e ("wifi: mac80211: flush queues on STA removal")

I saw in the original report that it indicated it was only for AP mode 
but after seeing this and checking some of our clients I saw that this 
is also happening in station mode too. I only have clients on 6.2 and 
6.8. I can confirm its not occurring on 6.2, but is on 6.8. I also tried 
your set of patches but did not notice any behavior difference with or 
without them. When it happens, its always just after a roam scan, ~4 
seconds go by and we get the failure followed by a "Connection to AP 
<mac> lost". Oddly the MAC address is all zeros.

Nov 25 09:09:50 iwd[16256]: src/station.c:station_start_roam() Using 
cached neighbor report for roam
Nov 25 09:09:54 kernel: ath10k_pci 0000:02:00.0: failed to flush 
transmit queue (skip 0 ar-state 1): 0
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
notification Del Station(20)
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_link_notify() event 16 
on ifindex 7
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
notification Deauthenticate(39)
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_deauthenticate_event()
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
notification Disconnect(48)
Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_disconnect_event()
Nov 25 09:09:54 iwd[16256]: Received Deauthentication event, reason: 4, 
from_ap: false
Nov 25 09:09:54 kernel: wlan0: Connection to AP 00:00:00:00:00:00 lost

Other times, the above logs are preceded by this:

Nov 26 00:25:25 kernel: ath10k_pci 0000:02:00.0: failed to flush sta txq 
(sta ca:55:b8:7a:91:4b skip 0 ar-state 1): 0

Note, the above logs are with your patches applied. Maybe this is a 
separate issue? Or do you think its related?

Thanks,

James

>
> V3:
>    - Initialize empty to true to fix smatch error
>
> V2:
>    - Add Closes tag
>    - Use atomic instead of spinlock for per sta pending frame counter
>    - Call ath10k_htt_tx_sta_dec_pending within rcu
>    - Rename pending_per_queue[] to num_pending_per_queue[]
>
> Remi Pommarel (2):
>    wifi: ath10k: Implement ieee80211 flush_sta callback
>    wifi: ath10k: Flush only requested txq in ath10k_flush()
>
>   drivers/net/wireless/ath/ath10k/core.h   |  2 +
>   drivers/net/wireless/ath/ath10k/htt.h    | 11 +++-
>   drivers/net/wireless/ath/ath10k/htt_tx.c | 49 +++++++++++++++-
>   drivers/net/wireless/ath/ath10k/mac.c    | 75 ++++++++++++++++++++----
>   drivers/net/wireless/ath/ath10k/txrx.c   | 11 ++--
>   5 files changed, 127 insertions(+), 21 deletions(-)
>


From prestwoj at gmail.com  Tue Nov 26 04:59:35 2024
From: prestwoj at gmail.com (James Prestwood)
Date: Tue, 26 Nov 2024 04:59:35 -0800
Subject: [RESEND PATCH v3 0/2] Improve ath10k flush queue mechanism
In-Reply-To: <20215f63-e2e6-4f9a-bbbe-d7535c5ce9d2@gmail.com>
References: <cover.1732293922.git.repk@triplefau.lt>
 <20215f63-e2e6-4f9a-bbbe-d7535c5ce9d2@gmail.com>
Message-ID: <8c2f274b-cf05-4fad-b9d6-fa9de1363d42@gmail.com>


On 11/26/24 4:57 AM, James Prestwood wrote:
> Hi Remi,
>
> On 11/22/24 8:48 AM, Remi Pommarel wrote:
>> It has been reported [0] that a 3-4 seconds (actually up to 5 sec) of
>> radio silence could be observed followed by the error below on ath10k
>> devices:
>>
>> ? ath10k_pci 0000:04:00.0: failed to flush transmit queue (skip 0 
>> ar-state 1): 0
>>
>> This is due to how the TX queues are flushed in ath10k. When a STA is
>> removed, mac80211 need to flush queues [1], but because ath10k does not
>> have a lightweight .flush_sta operation, ieee80211_flush_queues() is
>> called instead effectively blocking the whole queue during the drain
>> causing this radio silence. Also because ath10k_flush() waits for all
>> queued to be emptied, not only the flushed ones it could more easily
>> take up to 5 seconds to finish making the whole situation worst.
>>
>> The first patch of this series adds a .flush_sta operation to flush only
>> specific STA traffic avoiding the need to stop whole queues and should
>> be enough in itself to fix the reported issue.
>>
>> The second patch of this series is a proposal to improve ath10k_flush so
>> that it will be less likely to timeout waiting for non related queues to
>> drain.
>>
>> The abose kernel warning could still be observed (e.g. flushing a dead
>> STA) but should be now harmless.
>>
>> [0]: 
>> https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
>> [1]: commit 0b75a1b1e42e ("wifi: mac80211: flush queues on STA removal")
>
> I saw in the original report that it indicated it was only for AP mode 
> but after seeing this and checking some of our clients I saw that this 
> is also happening in station mode too. I only have clients on 6.2 and 
> 6.8. I can confirm its not occurring on 6.2, but is on 6.8. I also 
> tried your set of patches but did not notice any behavior difference 
> with or without them. When it happens, its always just after a roam 
> scan, ~4 seconds go by and we get the failure followed by a 
> "Connection to AP <mac> lost". Oddly the MAC address is all zeros.
>
> Nov 25 09:09:50 iwd[16256]: src/station.c:station_start_roam() Using 
> cached neighbor report for roam
> Nov 25 09:09:54 kernel: ath10k_pci 0000:02:00.0: failed to flush 
> transmit queue (skip 0 ar-state 1): 0
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
> notification Del Station(20)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_link_notify() event 16 
> on ifindex 7
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
> notification Deauthenticate(39)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_deauthenticate_event()
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME 
> notification Disconnect(48)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_disconnect_event()
> Nov 25 09:09:54 iwd[16256]: Received Deauthentication event, reason: 
> 4, from_ap: false
> Nov 25 09:09:54 kernel: wlan0: Connection to AP 00:00:00:00:00:00 lost
>
> Other times, the above logs are preceded by this:
>
> Nov 26 00:25:25 kernel: ath10k_pci 0000:02:00.0: failed to flush sta 
> txq (sta ca:55:b8:7a:91:4b skip 0 ar-state 1): 0
>
> Note, the above logs are with your patches applied. Maybe this is a 
> separate issue? Or do you think its related?

Forgot to mention, this is on the QCA6174 hw 3.2

firmware ver WLAN.RM.4.4.1-00288- api 6 features wowlan,ignore-otp,mfp 
crc32 bf907c7c

>
> Thanks,
>
> James
>
>>
>> V3:
>> ?? - Initialize empty to true to fix smatch error
>>
>> V2:
>> ?? - Add Closes tag
>> ?? - Use atomic instead of spinlock for per sta pending frame counter
>> ?? - Call ath10k_htt_tx_sta_dec_pending within rcu
>> ?? - Rename pending_per_queue[] to num_pending_per_queue[]
>>
>> Remi Pommarel (2):
>> ?? wifi: ath10k: Implement ieee80211 flush_sta callback
>> ?? wifi: ath10k: Flush only requested txq in ath10k_flush()
>>
>> ? drivers/net/wireless/ath/ath10k/core.h?? |? 2 +
>> ? drivers/net/wireless/ath/ath10k/htt.h??? | 11 +++-
>> ? drivers/net/wireless/ath/ath10k/htt_tx.c | 49 +++++++++++++++-
>> ? drivers/net/wireless/ath/ath10k/mac.c??? | 75 ++++++++++++++++++++----
>> ? drivers/net/wireless/ath/ath10k/txrx.c?? | 11 ++--
>> ? 5 files changed, 127 insertions(+), 21 deletions(-)
>>


From pmenzel at molgen.mpg.de  Tue Nov 26 00:58:22 2024
From: pmenzel at molgen.mpg.de (Paul Menzel)
Date: Tue, 26 Nov 2024 09:58:22 +0100
Subject: WARNING: drivers/net/wireless/ath/ath10k/mac.c:8750
 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
Message-ID: <637c5bb4-5278-44be-9ac3-9c0ef9297162@molgen.mpg.de>

Dear Linux folks,


On the Dell XPS 13 9360 with Linux 6.12.0-08446-g228a1157fb9f, I noticed 
the trace below:

```
[16805.002289] ------------[ cut here ]------------
[16805.002296] WARNING: CPU: 3 PID: 65835 at 
drivers/net/wireless/ath/ath10k/mac.c:8750 
ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.002321] Modules linked in: snd_usb_audio snd_usbmidi_lib 
snd_rawmidi cpuid sctp sd_mod usb_storage scsi_mod scsi_common r8153_ecm 
cdc_ether usbnet r8152 mii rfcomm cmac algif_hash algif_skcipher af_alg 
ctr ccm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device l2tp_ppp 
l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppox ppp_generic slhc 
xfrm_interface xfrm6_tunnel tunnel6 xfrm_user xfrm_algo uvcvideo 
snd_hda_codec_hdmi btusb btrtl videobuf2_vmalloc btintel 
videobuf2_memops uvc btbcm videobuf2_v4l2 videodev videobuf2_common 
bluetooth usbhid mc ecdh_generic ecc snd_ctl_led snd_hda_codec_realtek 
snd_hda_codec_generic snd_hda_scodec_component joydev 
snd_sof_pci_intel_skl snd_sof_intel_hda_generic snd_soc_acpi_intel_match 
snd_soc_acpi binfmt_misc snd_soc_acpi_intel_sdca_quirks snd_sof_pci 
snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation 
soundwire_cadence soundwire_bus snd_soc_sdca snd_sof_intel_hda_common 
snd_soc_hdac_hda snd_sof_intel_hda_mlink snd_sof_intel_hda snd_sof 
x86_pkg_temp_thermal
[16805.002674]  intel_powerclamp snd_sof_utils coretemp snd_soc_avs 
ath10k_pci nls_ascii snd_soc_hda_codec nls_cp437 kvm_intel ath10k_core 
snd_hda_ext_core vfat ath hid_multitouch fat snd_soc_core kvm 
hid_generic mac80211 snd_compress crct10dif_pclmul dell_pc snd_hda_intel 
crc32_pclmul platform_profile iTCO_wdt ghash_clmulni_intel intel_pmc_bxt 
sha512_ssse3 libarc4 snd_intel_dspcfg iTCO_vendor_support mei_wdt 
dell_laptop dell_wmi snd_intel_sdw_acpi sha512_generic mei_hdcp mei_pxp 
watchdog intel_xhci_usb_role_switch i915 dell_smbios snd_hda_codec 
sha256_ssse3 wmi_bmof sha1_ssse3 snd_hwdep cfg80211 
intel_wmi_thunderbolt snd_hda_core i2c_algo_bit rapl dell_wmi_descriptor 
drm_buddy processor_thermal_device_pci_legacy snd_pcm intel_cstate 
dcdbas intel_gtt intel_soc_dts_iosf intel_rapl_msr dell_smm_hwmon 
intel_uncore rfkill pcspkr processor_thermal_device i2c_i801 ucsi_acpi 
snd_timer processor_thermal_wt_hint drm_display_helper mei_me snd 
xhci_pci typec_ucsi intel_lpss_pci roles mei i2c_smbus i2c_hid_acpi 
soundcore
[16805.003046]  processor_thermal_rfim intel_pmc_core xhci_hcd i2c_hid 
typec intel_lpss ttm intel_vsec video hid soc_button_array intel_vbtn 
int3403_thermal wmi drm_kms_helper int3400_thermal 
processor_thermal_rapl idma64 pmt_telemetry battery ac pmt_class 
intel_rapl_common intel_pch_thermal acpi_thermal_rel usbcore 
processor_thermal_wt_req processor_thermal_power_floor intel_hid 
processor_thermal_mbox int340x_thermal_zone usb_common acpi_pad 
sparse_keymap button msr parport_pc ppdev lp parport efi_pstore drm 
configfs nfnetlink efivarfs autofs4 ext4 crc16 mbcache jbd2 dm_crypt 
dm_mod nvme evdev crc32c_intel serio_raw nvme_core aesni_intel gf128mul 
crypto_simd cryptd
[16805.003333] CPU: 3 UID: 0 PID: 65835 Comm: kworker/u16:23 Tainted: G 
    U             6.12.0-08446-g228a1157fb9f #29
[16805.003342] Tainted: [U]=USER
[16805.003348] Hardware name: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 
06/02/2022
[16805.003357] Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
[16805.003420] RIP: 0010:ath10k_mac_update_vif_chan+0x237/0x2e0 
[ath10k_core]
[16805.003440] Code: 83 c4 08 48 89 df 5b 5d 41 5c 41 5d 41 5e 41 5f e9 
5e f2 ff ff 0f 0b e9 48 ff ff ff 0f 0b e9 81 fe ff ff 0f 0b e9 3a ff ff 
ff <0f> 0b e9 73 fe ff ff 41 8b b6 a0 04 00 00 89 f2 89 c1 48 c7 c6 9e
[16805.003447] RSP: 0018:ffffa934872af6f0 EFLAGS: 00010246
[16805.003458] RAX: 0000000000000001 RBX: ffff93033d032000 RCX: 
0000000000000000
[16805.003465] RDX: 0000000000000001 RSI: ffff9303391be080 RDI: 
ffff93033d032000
[16805.003472] RBP: ffff9303391be080 R08: ffff93066f1d70c0 R09: 
0000000000000000
[16805.003478] R10: 0000000000000006 R11: 00000000ffffffff R12: 
ffff9303391be0a0
[16805.003485] R13: ffff9303391be080 R14: ffff930334941e38 R15: 
ffff9303391be080
[16805.003492] FS:  0000000000000000(0000) GS:ffff93066f180000(0000) 
knlGS:0000000000000000
[16805.003499] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[16805.003505] CR2: 00007f1bbb6c7bf8 CR3: 0000000378e21001 CR4: 
00000000003726f0
[16805.003513] Call Trace:
[16805.003521]  <TASK>
[16805.003528]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003547]  ? __warn.cold+0x93/0xf8
[16805.003558]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003583]  ? report_bug+0xfb/0x140
[16805.003600]  ? handle_bug+0x54/0x90
[16805.003611]  ? exc_invalid_op+0x17/0x60
[16805.003621]  ? asm_exc_invalid_op+0x1a/0x20
[16805.003692]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003722]  ath10k_mac_op_change_chanctx+0x11a/0x150 [ath10k_core]
[16805.003750]  drv_change_chanctx+0x40/0xe0 [mac80211]
[16805.003815]  _ieee80211_change_chanctx+0x207/0x3d0 [mac80211]
[16805.003873]  ieee80211_recalc_chanctx_chantype+0x1df/0x250 [mac80211]
[16805.003944]  ieee80211_link_change_chanreq+0x2c2/0x2e0 [mac80211]
[16805.004008]  ieee80211_config_bw.cold+0xd6/0x105 [mac80211]
[16805.004088]  ieee80211_rx_mgmt_assoc_resp.cold+0x949/0x1b29 [mac80211]
[16805.004258]  ieee80211_iface_work+0x37f/0x470 [mac80211]
[16805.004314]  cfg80211_wiphy_work+0xe9/0x160 [cfg80211]
[16805.004370]  process_one_work+0x171/0x320
[16805.004387]  worker_thread+0x24e/0x380
[16805.004404]  ? rescuer_thread+0x480/0x480
[16805.004413]  kthread+0xcf/0x100
[16805.004423]  ? kthread_park+0x80/0x80
[16805.004436]  ret_from_fork+0x31/0x50
[16805.004445]  ? kthread_park+0x80/0x80
[16805.004456]  ret_from_fork_asm+0x11/0x20
[16805.004487]  </TASK>
[16805.004494] ---[ end trace 0000000000000000 ]---
```

I do not see such a message in the logs since September 19th, so I 
believe it?s a regression.


Kind regards,

Paul
-------------- next part --------------
[    0.000000] Linux version 6.12.0-08446-g228a1157fb9f (build at bohemianrhapsody.molgen.mpg.de) (gcc (Debian 14.2.0-8) 14.2.0, GNU ld (GNU Binutils for Debian) 2.43.1) #29 SMP PREEMPT_DYNAMIC Sat Nov 23 10:15:41 CET 2024
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-6.12.0-08446-g228a1157fb9f root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer mem_sleep_default=deep log_buf_len=8M cryptomgr.notests
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000556aafff] usable
[    0.000000] BIOS-e820: [mem 0x00000000556ab000-0x00000000556abfff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x00000000556ac000-0x00000000556acfff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000556ad000-0x0000000064df3fff] usable
[    0.000000] BIOS-e820: [mem 0x0000000064df4000-0x000000006517ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000065180000-0x00000000651c3fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x00000000651c4000-0x000000006f871fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000006f872000-0x000000006fffefff] reserved
[    0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000070000000-0x0000000077ffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000078000000-0x00000000785fffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000078600000-0x000000007c7fffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000100000000-0x00000004817fffff] usable
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] APIC: Static calls initialized
[    0.000000] e820: update [mem 0x51a83018-0x51a93057] usable ==> usable
[    0.000000] extended physical RAM map:
[    0.000000] reserve setup_data: [mem 0x0000000000000000-0x0000000000057fff] usable
[    0.000000] reserve setup_data: [mem 0x0000000000058000-0x0000000000058fff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000059000-0x000000000009dfff] usable
[    0.000000] reserve setup_data: [mem 0x000000000009e000-0x00000000000fffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000000100000-0x0000000051a83017] usable
[    0.000000] reserve setup_data: [mem 0x0000000051a83018-0x0000000051a93057] usable
[    0.000000] reserve setup_data: [mem 0x0000000051a93058-0x00000000556aafff] usable
[    0.000000] reserve setup_data: [mem 0x00000000556ab000-0x00000000556abfff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x00000000556ac000-0x00000000556acfff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000556ad000-0x0000000064df3fff] usable
[    0.000000] reserve setup_data: [mem 0x0000000064df4000-0x000000006517ffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000065180000-0x00000000651c3fff] ACPI data
[    0.000000] reserve setup_data: [mem 0x00000000651c4000-0x000000006f871fff] ACPI NVS
[    0.000000] reserve setup_data: [mem 0x000000006f872000-0x000000006fffefff] reserved
[    0.000000] reserve setup_data: [mem 0x000000006ffff000-0x000000006fffffff] usable
[    0.000000] reserve setup_data: [mem 0x0000000070000000-0x0000000077ffffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000078000000-0x00000000785fffff] usable
[    0.000000] reserve setup_data: [mem 0x0000000078600000-0x000000007c7fffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fe000000-0x00000000fe010fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[    0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[    0.000000] reserve setup_data: [mem 0x0000000100000000-0x00000004817fffff] usable
[    0.000000] efi: EFI v2.4 by American Megatrends
[    0.000000] efi: ACPI=0x6518d000 ACPI 2.0=0x6518d000 SMBIOS=0xf0000 SMBIOS 3.0=0xf0020 TPMFinalLog=0x6f812000 ESRT=0x6fc86698 MEMATTR=0x62679298 INITRD=0x5577da98 TPMEventLog=0x65188018 
[    0.000000] efi: Remove mem36: MMIO range=[0xe0000000-0xefffffff] (256MB) from e820 map
[    0.000000] e820: remove [mem 0xe0000000-0xefffffff] reserved
[    0.000000] efi: Not removing mem37: MMIO range=[0xfe000000-0xfe010fff] (68KB) from e820 map
[    0.000000] efi: Not removing mem38: MMIO range=[0xfec00000-0xfec00fff] (4KB) from e820 map
[    0.000000] efi: Not removing mem39: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map
[    0.000000] efi: Remove mem40: MMIO range=[0xff000000-0xffffffff] (16MB) from e820 map
[    0.000000] e820: remove [mem 0xff000000-0xffffffff] reserved
[    0.000000] SMBIOS 3.0.0 present.
[    0.000000] DMI: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022
[    0.000000] DMI: Memory slots populated: 2/2
[    0.000000] tsc: Detected 2900.000 MHz processor
[    0.000000] tsc: Detected 2899.886 MHz TSC
[    0.000661] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000664] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000670] last_pfn = 0x481800 max_arch_pfn = 0x400000000
[    0.000673] MTRR map: 4 entries (3 fixed + 1 variable; max 23), built from 10 variable MTRRs
[    0.000675] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000972] last_pfn = 0x78600 max_arch_pfn = 0x400000000
[    0.007570] esrt: Reserving ESRT space from 0x000000006fc86698 to 0x000000006fc866d0.
[    0.007576] Using GB pages for direct mapping
[    0.014216] printk: log buffer data + meta data: 8388608 + 29360128 = 37748736 bytes
[    0.014217] printk: early log buf free: 125344(95%)
[    0.014218] Secure boot disabled
[    0.014218] RAMDISK: [mem 0x51a94000-0x5259dfff]
[    0.014222] ACPI: Early table checksum verification disabled
[    0.014225] ACPI: RSDP 0x000000006518D000 000024 (v02 DELL  )
[    0.014229] ACPI: XSDT 0x000000006518D0C8 00010C (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.014238] ACPI: FACP 0x00000000651B2A48 00010C (v05 DELL   CBX3     01072009 AMI  00010013)
[    0.014243] ACPI: DSDT 0x000000006518D260 0257E7 (v02 DELL   CBX3     01072009 INTL 20160422)
[    0.014245] ACPI: FACS 0x000000006F86F180 000040
[    0.014247] ACPI: APIC 0x00000000651B2B58 000084 (v03 DELL   CBX3     01072009 AMI  00010013)
[    0.014249] ACPI: FPDT 0x00000000651B2BE0 000044 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.014251] ACPI: FIDT 0x00000000651B2C28 0000AC (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.014253] ACPI: MCFG 0x00000000651B2CD8 00003C (v01 DELL   CBX3     01072009 MSFT 00000097)
[    0.014255] ACPI: HPET 0x00000000651B2D18 000038 (v01 DELL   CBX3     01072009 AMI. 0005000B)
[    0.014258] ACPI: SSDT 0x00000000651B2D50 000359 (v01 SataRe SataTabl 00001000 INTL 20160422)
[    0.014260] ACPI: BOOT 0x00000000651B30B0 000028 (v01 DELL   CBX3     01072009 AMI  00010013)
[    0.014262] ACPI: SSDT 0x00000000651B30D8 0012CF (v02 SaSsdt SaSsdt   00003000 INTL 20160422)
[    0.014264] ACPI: HPET 0x00000000651B43A8 000038 (v01 INTEL  KBL-ULT  00000001 MSFT 0000005F)
[    0.014266] ACPI: SSDT 0x00000000651B43E0 000D84 (v02 INTEL  xh_rvp07 00000000 INTL 20160422)
[    0.014268] ACPI: UEFI 0x00000000651B5168 000042 (v01                 00000000      00000000)
[    0.014270] ACPI: SSDT 0x00000000651B51B0 000EDE (v02 CpuRef CpuSsdt  00003000 INTL 20160422)
[    0.014272] ACPI: LPIT 0x00000000651B6090 000094 (v01 INTEL  KBL-ULT  00000000 MSFT 0000005F)
[    0.014274] ACPI: WSMT 0x00000000651B6128 000028 (v01 DELL   CBX3     00000000 MSFT 0000005F)
[    0.014276] ACPI: SSDT 0x00000000651B6150 000161 (v02 INTEL  HdaDsp   00000000 INTL 20160422)
[    0.014279] ACPI: SSDT 0x00000000651B62B8 00029F (v02 INTEL  sensrhub 00000000 INTL 20160422)
[    0.014281] ACPI: SSDT 0x00000000651B6558 003002 (v02 INTEL  PtidDevc 00001000 INTL 20160422)
[    0.014283] ACPI: SSDT 0x00000000651B9560 0000DB (v02 INTEL  TbtTypeC 00000000 INTL 20160422)
[    0.014285] ACPI: DBGP 0x00000000651B9640 000034 (v01 INTEL           00000002 MSFT 0000005F)
[    0.014287] ACPI: DBG2 0x00000000651B9678 000054 (v00 INTEL           00000002 MSFT 0000005F)
[    0.014289] ACPI: SSDT 0x00000000651B96D0 0007DD (v02 INTEL  UsbCTabl 00001000 INTL 20160422)
[    0.014291] ACPI: SSDT 0x00000000651B9EB0 0084F1 (v02 DptfTa DptfTabl 00001000 INTL 20160422)
[    0.014293] ACPI: SLIC 0x00000000651C23A8 000176 (v03 DELL   CBX3     01072009 MSFT 00010013)
[    0.014295] ACPI: NHLT 0x00000000651C2520 00002D (v00 INTEL  EDK2     00000002      01000013)
[    0.014298] ACPI: BGRT 0x00000000651C2550 000038 (v00                 01072009 AMI  00010013)
[    0.014300] ACPI: TPM2 0x00000000651C2588 000034 (v03        Tpm2Tabl 00000001 AMI  00000000)
[    0.014302] ACPI: ASF! 0x00000000651C25C0 0000A0 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[    0.014304] ACPI: DMAR 0x00000000651C2660 0000F0 (v01 INTEL  KBL      00000001 INTL 00000001)
[    0.014306] ACPI: Reserving FACP table memory at [mem 0x651b2a48-0x651b2b53]
[    0.014307] ACPI: Reserving DSDT table memory at [mem 0x6518d260-0x651b2a46]
[    0.014308] ACPI: Reserving FACS table memory at [mem 0x6f86f180-0x6f86f1bf]
[    0.014308] ACPI: Reserving APIC table memory at [mem 0x651b2b58-0x651b2bdb]
[    0.014309] ACPI: Reserving FPDT table memory at [mem 0x651b2be0-0x651b2c23]
[    0.014310] ACPI: Reserving FIDT table memory at [mem 0x651b2c28-0x651b2cd3]
[    0.014310] ACPI: Reserving MCFG table memory at [mem 0x651b2cd8-0x651b2d13]
[    0.014311] ACPI: Reserving HPET table memory at [mem 0x651b2d18-0x651b2d4f]
[    0.014312] ACPI: Reserving SSDT table memory at [mem 0x651b2d50-0x651b30a8]
[    0.014312] ACPI: Reserving BOOT table memory at [mem 0x651b30b0-0x651b30d7]
[    0.014313] ACPI: Reserving SSDT table memory at [mem 0x651b30d8-0x651b43a6]
[    0.014313] ACPI: Reserving HPET table memory at [mem 0x651b43a8-0x651b43df]
[    0.014314] ACPI: Reserving SSDT table memory at [mem 0x651b43e0-0x651b5163]
[    0.014315] ACPI: Reserving UEFI table memory at [mem 0x651b5168-0x651b51a9]
[    0.014315] ACPI: Reserving SSDT table memory at [mem 0x651b51b0-0x651b608d]
[    0.014316] ACPI: Reserving LPIT table memory at [mem 0x651b6090-0x651b6123]
[    0.014316] ACPI: Reserving WSMT table memory at [mem 0x651b6128-0x651b614f]
[    0.014317] ACPI: Reserving SSDT table memory at [mem 0x651b6150-0x651b62b0]
[    0.014318] ACPI: Reserving SSDT table memory at [mem 0x651b62b8-0x651b6556]
[    0.014318] ACPI: Reserving SSDT table memory at [mem 0x651b6558-0x651b9559]
[    0.014319] ACPI: Reserving SSDT table memory at [mem 0x651b9560-0x651b963a]
[    0.014320] ACPI: Reserving DBGP table memory at [mem 0x651b9640-0x651b9673]
[    0.014320] ACPI: Reserving DBG2 table memory at [mem 0x651b9678-0x651b96cb]
[    0.014321] ACPI: Reserving SSDT table memory at [mem 0x651b96d0-0x651b9eac]
[    0.014321] ACPI: Reserving SSDT table memory at [mem 0x651b9eb0-0x651c23a0]
[    0.014322] ACPI: Reserving SLIC table memory at [mem 0x651c23a8-0x651c251d]
[    0.014323] ACPI: Reserving NHLT table memory at [mem 0x651c2520-0x651c254c]
[    0.014323] ACPI: Reserving BGRT table memory at [mem 0x651c2550-0x651c2587]
[    0.014324] ACPI: Reserving TPM2 table memory at [mem 0x651c2588-0x651c25bb]
[    0.014325] ACPI: Reserving ASF! table memory at [mem 0x651c25c0-0x651c265f]
[    0.014325] ACPI: Reserving DMAR table memory at [mem 0x651c2660-0x651c274f]
[    0.014442] No NUMA configuration found
[    0.014442] Faking a node at [mem 0x0000000000000000-0x00000004817fffff]
[    0.014452] NODE_DATA(0) allocated [mem 0x47f3d5680-0x47f3fffff]
[    0.014637] Zone ranges:
[    0.014637]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.014639]   DMA32    [mem 0x0000000001000000-0x00000000ffffffff]
[    0.014640]   Normal   [mem 0x0000000100000000-0x00000004817fffff]
[    0.014642]   Device   empty
[    0.014642] Movable zone start for each node
[    0.014644] Early memory node ranges
[    0.014645]   node   0: [mem 0x0000000000001000-0x0000000000057fff]
[    0.014646]   node   0: [mem 0x0000000000059000-0x000000000009dfff]
[    0.014647]   node   0: [mem 0x0000000000100000-0x00000000556aafff]
[    0.014648]   node   0: [mem 0x00000000556ad000-0x0000000064df3fff]
[    0.014648]   node   0: [mem 0x000000006ffff000-0x000000006fffffff]
[    0.014649]   node   0: [mem 0x0000000078000000-0x00000000785fffff]
[    0.014650]   node   0: [mem 0x0000000100000000-0x00000004817fffff]
[    0.014652] Initmem setup node 0 [mem 0x0000000000001000-0x00000004817fffff]
[    0.014656] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.014658] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.014680] On node 0, zone DMA: 98 pages in unavailable ranges
[    0.017046] On node 0, zone DMA32: 2 pages in unavailable ranges
[    0.017482] On node 0, zone DMA32: 45579 pages in unavailable ranges
[    0.018017] On node 0, zone Normal: 31232 pages in unavailable ranges
[    0.018266] On node 0, zone Normal: 26624 pages in unavailable ranges
[    0.018274] Reserving Intel graphics memory at [mem 0x7a800000-0x7c7fffff]
[    0.018464] ACPI: PM-Timer IO Port: 0x1808
[    0.018470] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.018471] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[    0.018472] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[    0.018472] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[    0.018498] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119
[    0.018501] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.018502] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.018505] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.018506] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[    0.018512] e820: update [mem 0x62260000-0x623ecfff] usable ==> reserved
[    0.018520] TSC deadline timer available
[    0.018524] CPU topo: Max. logical packages:   1
[    0.018524] CPU topo: Max. logical dies:       1
[    0.018525] CPU topo: Max. dies per package:   1
[    0.018528] CPU topo: Max. threads per core:   2
[    0.018529] CPU topo: Num. cores per package:     2
[    0.018530] CPU topo: Num. threads per package:   4
[    0.018530] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs
[    0.018548] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.018550] PM: hibernation: Registered nosave memory: [mem 0x00058000-0x00058fff]
[    0.018552] PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x000fffff]
[    0.018553] PM: hibernation: Registered nosave memory: [mem 0x51a83000-0x51a83fff]
[    0.018555] PM: hibernation: Registered nosave memory: [mem 0x51a93000-0x51a93fff]
[    0.018556] PM: hibernation: Registered nosave memory: [mem 0x556ab000-0x556abfff]
[    0.018557] PM: hibernation: Registered nosave memory: [mem 0x556ac000-0x556acfff]
[    0.018558] PM: hibernation: Registered nosave memory: [mem 0x62260000-0x623ecfff]
[    0.018560] PM: hibernation: Registered nosave memory: [mem 0x64df4000-0x6517ffff]
[    0.018560] PM: hibernation: Registered nosave memory: [mem 0x65180000-0x651c3fff]
[    0.018561] PM: hibernation: Registered nosave memory: [mem 0x651c4000-0x6f871fff]
[    0.018561] PM: hibernation: Registered nosave memory: [mem 0x6f872000-0x6fffefff]
[    0.018563] PM: hibernation: Registered nosave memory: [mem 0x70000000-0x77ffffff]
[    0.018564] PM: hibernation: Registered nosave memory: [mem 0x78600000-0x7c7fffff]
[    0.018565] PM: hibernation: Registered nosave memory: [mem 0x7c800000-0xfdffffff]
[    0.018565] PM: hibernation: Registered nosave memory: [mem 0xfe000000-0xfe010fff]
[    0.018566] PM: hibernation: Registered nosave memory: [mem 0xfe011000-0xfebfffff]
[    0.018566] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[    0.018567] PM: hibernation: Registered nosave memory: [mem 0xfec01000-0xfedfffff]
[    0.018567] PM: hibernation: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[    0.018568] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xffffffff]
[    0.018569] [mem 0x7c800000-0xfdffffff] available for PCI devices
[    0.018570] Booting paravirtualized kernel on bare hardware
[    0.018572] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[    0.023209] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.023490] percpu: Embedded 94 pages/cpu s290816 r65536 d28672 u524288
[    0.023499] pcpu-alloc: s290816 r65536 d28672 u524288 alloc=1*2097152
[    0.023501] pcpu-alloc: [0] 0 1 2 3 
[    0.023519] Kernel command line: BOOT_IMAGE=/vmlinuz-6.12.0-08446-g228a1157fb9f root=UUID=32e29882-d94d-4a92-9ee4-4d03002bfa29 ro quiet pci=noaer mem_sleep_default=deep log_buf_len=8M cryptomgr.notests
[    0.023584] Unknown kernel command line parameters "BOOT_IMAGE=/vmlinuz-6.12.0-08446-g228a1157fb9f", will be passed to user space.
[    0.023609] random: crng init done
[    0.025128] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear)
[    0.025870] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.025919] Fallback order for Node 0: 0 
[    0.025922] Built 1 zonelists, mobility grouping on.  Total pages: 4090767
[    0.025923] Policy zone: Normal
[    0.025929] mem auto-init: stack:all(zero), heap alloc:on, heap free:off
[    0.025935] software IO TLB: area num 4.
[    0.044694] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.044696] kmemleak: Kernel memory leak detector disabled
[    0.044725] ftrace: allocating 43010 entries in 169 pages
[    0.051879] ftrace: allocated 169 pages with 4 groups
[    0.052566] Dynamic Preempt: voluntary
[    0.052599] rcu: Preemptible hierarchical RCU implementation.
[    0.052599] rcu: 	RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4.
[    0.052601] 	Trampoline variant of Tasks RCU enabled.
[    0.052601] 	Rude variant of Tasks RCU enabled.
[    0.052601] 	Tracing variant of Tasks RCU enabled.
[    0.052602] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.052603] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.052608] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.052609] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.052610] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.056385] NR_IRQS: 524544, nr_irqs: 1024, preallocated irqs: 16
[    0.056596] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.056768] Console: colour dummy device 80x25
[    0.056770] printk: legacy console [tty0] enabled
[    0.056808] ACPI: Core revision 20240827
[    0.056962] hpet: HPET dysfunctional in PC10. Force disabled.
[    0.057013] APIC: Switch to symmetric I/O mode setup
[    0.057015] DMAR: Host address width 39
[    0.057017] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[    0.057022] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
[    0.057024] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[    0.057029] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
[    0.057031] DMAR: RMRR base: 0x00000064ec2000 end: 0x00000064ee1fff
[    0.057032] DMAR: RMRR base: 0x0000007a000000 end: 0x0000007c7fffff
[    0.057033] DMAR: ANDD device: 1 name: \_SB.PCI0.I2C0
[    0.057034] DMAR: ANDD device: 2 name: \_SB.PCI0.I2C1
[    0.057036] DMAR-IR: IOAPIC id 2 under DRHD base  0xfed91000 IOMMU 1
[    0.057038] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[    0.057039] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
[    0.058667] DMAR-IR: Enabled IRQ remapping in x2apic mode
[    0.058669] x2apic enabled
[    0.058726] APIC: Switched APIC routing to: cluster x2apic
[    0.062600] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x29ccd767b87, max_idle_ns: 440795223720 ns
[    0.062606] Calibrating delay loop (skipped), value calculated using timer frequency.. 5799.77 BogoMIPS (lpj=11599544)
[    0.062642] CPU0: Thermal monitoring enabled (TM1)
[    0.062680] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
[    0.062682] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
[    0.062686] process: using mwait in idle threads
[    0.062689] Spectre V2 : User space: Vulnerable
[    0.062690] Speculative Store Bypass: Vulnerable
[    0.062693] SRBDS: Vulnerable
[    0.062698] GDS: Vulnerable
[    0.062703] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.062704] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.062705] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.062705] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers'
[    0.062706] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR'
[    0.062707] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.062709] x86/fpu: xstate_offset[3]:  832, xstate_sizes[3]:   64
[    0.062710] x86/fpu: xstate_offset[4]:  896, xstate_sizes[4]:   64
[    0.062711] x86/fpu: Enabled xstate features 0x1f, context size is 960 bytes, using 'compacted' format.
[    0.066603] Freeing SMP alternatives memory: 36K
[    0.066603] pid_max: default: 32768 minimum: 301
[    0.066603] LSM: initializing lsm=capability,landlock,apparmor,bpf
[    0.066603] landlock: Up and running.
[    0.066603] AppArmor: AppArmor initialized
[    0.066603] LSM support for eBPF active
[    0.066603] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.066603] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.066603] smpboot: CPU0: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz (family: 0x6, model: 0x8e, stepping: 0x9)
[    0.066603] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver.
[    0.066603] ... version:                4
[    0.066603] ... bit width:              48
[    0.066603] ... generic registers:      4
[    0.066603] ... value mask:             0000ffffffffffff
[    0.066603] ... max period:             00007fffffffffff
[    0.066603] ... fixed-purpose events:   3
[    0.066603] ... event mask:             000000070000000f
[    0.066603] signal: max sigframe size: 1616
[    0.066603] Estimated ratio of average max frequency by base frequency (times 1024): 1235
[    0.066603] rcu: Hierarchical SRCU implementation.
[    0.066603] rcu: 	Max phase no-delay instances is 1000.
[    0.066603] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[    0.066603] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.066603] smp: Bringing up secondary CPUs ...
[    0.066603] smpboot: x86: Booting SMP configuration:
[    0.066603] .... node  #0, CPUs:      #1 #2 #3
[    0.066603] smp: Brought up 1 node, 4 CPUs
[    0.066603] smpboot: Total of 4 processors activated (23199.08 BogoMIPS)
[    0.088616] node 0 deferred pages initialised in 24ms
[    0.090418] Memory: 15905904K/16363068K available (14336K kernel code, 2563K rwdata, 10192K rodata, 2868K init, 6376K bss, 446256K reserved, 0K cma-reserved)
[    0.090985] devtmpfs: initialized
[    0.090985] x86/mm: Memory block size: 128MB
[    0.091735] ACPI: PM: Registering ACPI NVS region [mem 0x556ab000-0x556abfff] (4096 bytes)
[    0.091735] ACPI: PM: Registering ACPI NVS region [mem 0x651c4000-0x6f871fff] (174776320 bytes)
[    0.092129] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.092136] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.092194] pinctrl core: initialized pinctrl subsystem
[    0.092674] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.092884] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.093003] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.094698] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.094715] audit: initializing netlink subsys (disabled)
[    0.094729] audit: type=2000 audit(1732361269.032:1): state=initialized audit_enabled=0 res=1
[    0.094729] thermal_sys: Registered thermal governor 'fair_share'
[    0.094729] thermal_sys: Registered thermal governor 'bang_bang'
[    0.094729] thermal_sys: Registered thermal governor 'step_wise'
[    0.094729] thermal_sys: Registered thermal governor 'user_space'
[    0.094729] thermal_sys: Registered thermal governor 'power_allocator'
[    0.094729] cpuidle: using governor ladder
[    0.094729] cpuidle: using governor menu
[    0.094729] Simple Boot Flag at 0x47 set to 0x80
[    0.094729] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.094729] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.094729] PCI: ECAM [mem 0xe0000000-0xefffffff] (base 0xe0000000) for domain 0000 [bus 00-ff]
[    0.094729] PCI: Using configuration type 1 for base access
[    0.094785] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.094785] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.094785] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page
[    0.094785] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.094785] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page
[    0.094785] ACPI: Added _OSI(Module Device)
[    0.094785] ACPI: Added _OSI(Processor Device)
[    0.094785] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.094785] ACPI: Added _OSI(Processor Aggregator Device)
[    0.128862] ACPI: 11 ACPI AML tables successfully acquired and loaded
[    0.135785] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[    0.140534] ACPI: Dynamic OEM Table Load:
[    0.140534] ACPI: SSDT 0xFFFF930301197400 0003FF (v02 PmRef  Cpu0Cst  00003001 INTL 20160422)
[    0.140534] ACPI: Dynamic OEM Table Load:
[    0.140534] ACPI: SSDT 0xFFFF93030179D000 0006F6 (v02 PmRef  Cpu0Ist  00003000 INTL 20160422)
[    0.143622] ACPI: Dynamic OEM Table Load:
[    0.143628] ACPI: SSDT 0xFFFF93030179B000 00065C (v02 PmRef  ApIst    00003000 INTL 20160422)
[    0.144697] ACPI: Dynamic OEM Table Load:
[    0.144701] ACPI: SSDT 0xFFFF93030119EE00 00018A (v02 PmRef  ApCst    00003000 INTL 20160422)
[    0.147207] ACPI: EC: EC started
[    0.147208] ACPI: EC: interrupt blocked
[    0.152116] ACPI: EC: EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.152119] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC used to handle transactions
[    0.152121] ACPI: Interpreter enabled
[    0.152158] ACPI: PM: (supports S0 S3 S4 S5)
[    0.152160] ACPI: Using IOAPIC for interrupt routing
[    0.152193] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.152194] PCI: Using E820 reservations for host bridge windows
[    0.152726] ACPI: Enabled 8 GPEs in block 00 to 7F
[    0.155918] ACPI: \_SB_.PCI0.RP09.PXSX.WRST: New power resource
[    0.156190] ACPI: \_SB_.PCI0.RP10.PXSX.WRST: New power resource
[    0.156455] ACPI: \_SB_.PCI0.RP11.PXSX.WRST: New power resource
[    0.156719] ACPI: \_SB_.PCI0.RP12.PXSX.WRST: New power resource
[    0.156980] ACPI: \_SB_.PCI0.RP13.PXSX.WRST: New power resource
[    0.157248] ACPI: \_SB_.PCI0.RP01.PXSX.WRST: New power resource
[    0.157873] ACPI: \_SB_.PCI0.RP02.PXSX.WRST: New power resource
[    0.158139] ACPI: \_SB_.PCI0.RP03.PXSX.WRST: New power resource
[    0.158402] ACPI: \_SB_.PCI0.RP04.PXSX.WRST: New power resource
[    0.158680] ACPI: \_SB_.PCI0.RP05.PXSX.WRST: New power resource
[    0.158944] ACPI: \_SB_.PCI0.RP06.PXSX.WRST: New power resource
[    0.159206] ACPI: \_SB_.PCI0.RP07.PXSX.WRST: New power resource
[    0.159472] ACPI: \_SB_.PCI0.RP08.PXSX.WRST: New power resource
[    0.159745] ACPI: \_SB_.PCI0.RP17.PXSX.WRST: New power resource
[    0.160011] ACPI: \_SB_.PCI0.RP18.PXSX.WRST: New power resource
[    0.160278] ACPI: \_SB_.PCI0.RP19.PXSX.WRST: New power resource
[    0.160541] ACPI: \_SB_.PCI0.RP20.PXSX.WRST: New power resource
[    0.161638] ACPI: \_SB_.PCI0.RP14.PXSX.WRST: New power resource
[    0.161900] ACPI: \_SB_.PCI0.RP15.PXSX.WRST: New power resource
[    0.162167] ACPI: \_SB_.PCI0.RP16.PXSX.WRST: New power resource
[    0.183986] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[    0.183993] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.184156] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug SHPCHotplug PME]
[    0.184454] acpi PNP0A08:00: _OSC: OS now controls [PCIeCapability LTR]
[    0.184455] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
[    0.185195] PCI host bridge to bus 0000:00
[    0.185199] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.185201] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.185203] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window]
[    0.185204] pci_bus 0000:00: root bus resource [mem 0x7c800000-0xdfffffff window]
[    0.185205] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff window]
[    0.185207] pci_bus 0000:00: root bus resource [bus 00-fe]
[    0.185221] pci 0000:00:00.0: [8086:5904] type 00 class 0x060000 conventional PCI endpoint
[    0.185284] pci 0000:00:02.0: [8086:5916] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint
[    0.185291] pci 0000:00:02.0: BAR 0 [mem 0xdb000000-0xdbffffff 64bit]
[    0.185296] pci 0000:00:02.0: BAR 2 [mem 0x90000000-0x9fffffff 64bit pref]
[    0.185300] pci 0000:00:02.0: BAR 4 [io  0xf000-0xf03f]
[    0.185313] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.185439] pci 0000:00:04.0: [8086:1903] type 00 class 0x118000 conventional PCI endpoint
[    0.185447] pci 0000:00:04.0: BAR 0 [mem 0xdc320000-0xdc327fff 64bit]
[    0.185695] pci 0000:00:14.0: [8086:9d2f] type 00 class 0x0c0330 conventional PCI endpoint
[    0.185710] pci 0000:00:14.0: BAR 0 [mem 0xdc310000-0xdc31ffff 64bit]
[    0.185765] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.186228] pci 0000:00:14.2: [8086:9d31] type 00 class 0x118000 conventional PCI endpoint
[    0.186242] pci 0000:00:14.2: BAR 0 [mem 0xdc334000-0xdc334fff 64bit]
[    0.186377] pci 0000:00:15.0: [8086:9d60] type 00 class 0x118000 conventional PCI endpoint
[    0.186406] pci 0000:00:15.0: BAR 0 [mem 0xdc333000-0xdc333fff 64bit]
[    0.186743] pci 0000:00:15.1: [8086:9d61] type 00 class 0x118000 conventional PCI endpoint
[    0.186772] pci 0000:00:15.1: BAR 0 [mem 0xdc332000-0xdc332fff 64bit]
[    0.187069] pci 0000:00:16.0: [8086:9d3a] type 00 class 0x078000 conventional PCI endpoint
[    0.187082] pci 0000:00:16.0: BAR 0 [mem 0xdc331000-0xdc331fff 64bit]
[    0.187125] pci 0000:00:16.0: PME# supported from D3hot
[    0.187426] pci 0000:00:1c.0: [8086:9d10] type 01 class 0x060400 PCIe Root Port
[    0.187446] pci 0000:00:1c.0: PCI bridge to [bus 01-39]
[    0.187451] pci 0000:00:1c.0:   bridge window [mem 0xc4000000-0xda0fffff]
[    0.187458] pci 0000:00:1c.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[    0.187508] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.187913] pci 0000:00:1c.4: [8086:9d14] type 01 class 0x060400 PCIe Root Port
[    0.187933] pci 0000:00:1c.4: PCI bridge to [bus 3a]
[    0.187938] pci 0000:00:1c.4:   bridge window [mem 0xdc000000-0xdc1fffff]
[    0.187993] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.188400] pci 0000:00:1d.0: [8086:9d18] type 01 class 0x060400 PCIe Root Port
[    0.188419] pci 0000:00:1d.0: PCI bridge to [bus 3b]
[    0.188423] pci 0000:00:1d.0:   bridge window [mem 0xdc200000-0xdc2fffff]
[    0.188472] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[    0.188890] pci 0000:00:1f.0: [8086:9d58] type 00 class 0x060100 conventional PCI endpoint
[    0.189173] pci 0000:00:1f.2: [8086:9d21] type 00 class 0x058000 conventional PCI endpoint
[    0.189185] pci 0000:00:1f.2: BAR 0 [mem 0xdc32c000-0xdc32ffff]
[    0.189393] pci 0000:00:1f.3: [8086:9d71] type 00 class 0x040380 conventional PCI endpoint
[    0.189411] pci 0000:00:1f.3: BAR 0 [mem 0xdc328000-0xdc32bfff 64bit]
[    0.189434] pci 0000:00:1f.3: BAR 4 [mem 0xdc300000-0xdc30ffff 64bit]
[    0.189475] pci 0000:00:1f.3: PME# supported from D3hot D3cold
[    0.190032] pci 0000:00:1f.4: [8086:9d23] type 00 class 0x0c0500 conventional PCI endpoint
[    0.190090] pci 0000:00:1f.4: BAR 0 [mem 0xdc330000-0xdc3300ff 64bit]
[    0.190160] pci 0000:00:1f.4: BAR 4 [io  0xf040-0xf05f]
[    0.190478] pci 0000:00:1c.0: PCI bridge to [bus 01-39]
[    0.190824] pci 0000:3a:00.0: [168c:003e] type 00 class 0x028000 PCIe Endpoint
[    0.191040] pci 0000:3a:00.0: BAR 0 [mem 0xdc000000-0xdc1fffff 64bit]
[    0.192240] pci 0000:3a:00.0: PME# supported from D0 D3hot D3cold
[    0.193856] pci 0000:00:1c.4: PCI bridge to [bus 3a]
[    0.193948] pci 0000:3b:00.0: [1c5c:1284] type 00 class 0x010802 PCIe Endpoint
[    0.193967] pci 0000:3b:00.0: BAR 0 [mem 0xdc200000-0xdc203fff 64bit]
[    0.194080] pci 0000:3b:00.0: PME# supported from D0 D1 D3hot
[    0.194410] pci 0000:00:1d.0: PCI bridge to [bus 3b]
[    0.197367] ACPI: PCI: Interrupt link LNKA configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKB configured for IRQ 10
[    0.197367] ACPI: PCI: Interrupt link LNKC configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKD configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKE configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKF configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKG configured for IRQ 11
[    0.197367] ACPI: PCI: Interrupt link LNKH configured for IRQ 11
[    0.203417] ACPI: EC: interrupt unblocked
[    0.203418] ACPI: EC: event unblocked
[    0.203424] ACPI: EC: EC_CMD/EC_SC=0x934, EC_DATA=0x930
[    0.203425] ACPI: EC: GPE=0x14
[    0.203427] ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC initialization complete
[    0.203428] ACPI: \_SB_.PCI0.LPCB.ECDV: EC: Used to handle transactions and events
[    0.206637] iommu: Default domain type: Translated
[    0.206637] iommu: DMA domain TLB invalidation policy: lazy mode
[    0.206890] pps_core: LinuxPPS API ver. 1 registered
[    0.206892] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti at linux.it>
[    0.206895] PTP clock support registered
[    0.206904] EDAC MC: Ver: 3.0.0
[    0.207455] efivars: Registered efivars operations
[    0.207455] NetLabel: Initializing
[    0.207455] NetLabel:  domain hash size = 128
[    0.207455] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.207455] NetLabel:  unlabeled traffic allowed by default
[    0.207455] PCI: Using ACPI for IRQ routing
[    0.234168] PCI: pci_cache_line_size set to 64 bytes
[    0.234531] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
[    0.234533] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.234534] e820: reserve RAM buffer [mem 0x51a83018-0x53ffffff]
[    0.234535] e820: reserve RAM buffer [mem 0x556ab000-0x57ffffff]
[    0.234536] e820: reserve RAM buffer [mem 0x62260000-0x63ffffff]
[    0.234537] e820: reserve RAM buffer [mem 0x64df4000-0x67ffffff]
[    0.234538] e820: reserve RAM buffer [mem 0x78600000-0x7bffffff]
[    0.234539] e820: reserve RAM buffer [mem 0x481800000-0x483ffffff]
[    0.234569] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.234569] pci 0000:00:02.0: vgaarb: bridge control possible
[    0.234569] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.234569] vgaarb: loaded
[    0.234645] clocksource: Switched to clocksource tsc-early
[    0.234760] VFS: Disk quotas dquot_6.6.0
[    0.234769] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.234850] AppArmor: AppArmor Filesystem Enabled
[    0.234861] pnp: PnP ACPI init
[    0.235060] system 00:00: [io  0x0680-0x069f] has been reserved
[    0.235063] system 00:00: [io  0xffff] has been reserved
[    0.235065] system 00:00: [io  0xffff] has been reserved
[    0.235066] system 00:00: [io  0xffff] has been reserved
[    0.235067] system 00:00: [io  0x1800-0x18fe] has been reserved
[    0.235068] system 00:00: [io  0x164e-0x164f] has been reserved
[    0.235191] system 00:02: [io  0x1854-0x1857] has been reserved
[    0.235534] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
[    0.235536] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
[    0.235539] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
[    0.235540] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved
[    0.235542] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
[    0.235543] system 00:05: [mem 0xfed90000-0xfed93fff] could not be reserved
[    0.235545] system 00:05: [mem 0xfed45000-0xfed8ffff] has been reserved
[    0.235546] system 00:05: [mem 0xff000000-0xffffffff] has been reserved
[    0.235548] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
[    0.235550] system 00:05: [mem 0xdffe0000-0xdfffffff] has been reserved
[    0.235585] system 00:06: [mem 0xfd000000-0xfdabffff] has been reserved
[    0.235587] system 00:06: [mem 0xfdad0000-0xfdadffff] has been reserved
[    0.235589] system 00:06: [mem 0xfdb00000-0xfdffffff] has been reserved
[    0.235590] system 00:06: [mem 0xfe000000-0xfe01ffff] could not be reserved
[    0.235592] system 00:06: [mem 0xfe036000-0xfe03bfff] has been reserved
[    0.235594] system 00:06: [mem 0xfe03d000-0xfe3fffff] has been reserved
[    0.235595] system 00:06: [mem 0xfe410000-0xfe7fffff] has been reserved
[    0.235853] system 00:07: [io  0xff00-0xfffe] has been reserved
[    0.236821] system 00:08: [mem 0xfe029000-0xfe029fff] has been reserved
[    0.236824] system 00:08: [mem 0xfe028000-0xfe028fff] has been reserved
[    0.241620] pnp: PnP ACPI: found 9 devices
[    0.246998] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.247045] NET: Registered PF_INET protocol family
[    0.247167] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.258961] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.258984] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.259027] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.259226] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    0.259435] TCP: Hash tables configured (established 131072 bind 65536)
[    0.259516] MPTCP token hash table entries: 16384 (order: 6, 393216 bytes, linear)
[    0.259576] UDP hash table entries: 8192 (order: 7, 524288 bytes, linear)
[    0.259654] UDP-Lite hash table entries: 8192 (order: 7, 524288 bytes, linear)
[    0.259736] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.259741] NET: Registered PF_XDP protocol family
[    0.259750] pci 0000:00:1c.0: bridge window [io  0x1000-0x0fff] to [bus 01-39] add_size 1000
[    0.259760] pci 0000:00:1c.0: bridge window [io  0x2000-0x2fff]: assigned
[    0.259763] pci 0000:00:1c.0: PCI bridge to [bus 01-39]
[    0.259766] pci 0000:00:1c.0:   bridge window [io  0x2000-0x2fff]
[    0.259769] pci 0000:00:1c.0:   bridge window [mem 0xc4000000-0xda0fffff]
[    0.259772] pci 0000:00:1c.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[    0.259776] pci 0000:00:1c.4: PCI bridge to [bus 3a]
[    0.259779] pci 0000:00:1c.4:   bridge window [mem 0xdc000000-0xdc1fffff]
[    0.259784] pci 0000:00:1d.0: PCI bridge to [bus 3b]
[    0.259787] pci 0000:00:1d.0:   bridge window [mem 0xdc200000-0xdc2fffff]
[    0.259794] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.259796] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.259797] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window]
[    0.259798] pci_bus 0000:00: resource 7 [mem 0x7c800000-0xdfffffff window]
[    0.259799] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window]
[    0.259801] pci_bus 0000:01: resource 0 [io  0x2000-0x2fff]
[    0.259802] pci_bus 0000:01: resource 1 [mem 0xc4000000-0xda0fffff]
[    0.259803] pci_bus 0000:01: resource 2 [mem 0xa0000000-0xc1ffffff 64bit pref]
[    0.259804] pci_bus 0000:3a: resource 1 [mem 0xdc000000-0xdc1fffff]
[    0.259805] pci_bus 0000:3b: resource 1 [mem 0xdc200000-0xdc2fffff]
[    0.260396] PCI: CLS 0 bytes, default 64
[    0.260440] pci 0000:00:1f.1: [8086:9d20] type 00 class 0x058000 conventional PCI endpoint
[    0.260500] pci 0000:00:1f.1: BAR 0 [mem 0xfd000000-0xfdffffff 64bit]
[    0.260736] DMAR: ACPI device "device:79" under DMAR at fed91000 as 00:15.0
[    0.260739] DMAR: ACPI device "device:7a" under DMAR at fed91000 as 00:15.1
[    0.260748] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.260749] software IO TLB: mapped [mem 0x000000005e260000-0x0000000062260000] (64MB)
[    0.260778] Unpacking initramfs...
[    0.260804] sgx: EPC section 0x70200000-0x75f7ffff
[    0.261828] Initialise system trusted keyrings
[    0.261843] Key type blacklist registered
[    0.261966] workingset: timestamp_bits=36 max_order=22 bucket_order=0
[    0.262006] zbud: loaded
[    0.262271] fuse: init (API version 7.41)
[    0.262586] Key type asymmetric registered
[    0.262591] Asymmetric key parser 'x509' registered
[    0.283606] Freeing initrd memory: 11304K
[    0.287344] alg: self-tests disabled
[    0.287502] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.287562] io scheduler mq-deadline registered
[    0.292496] ledtrig-cpu: registered to indicate activity on CPUs
[    0.293103] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.295361] thermal LNXTHERM:00: registered as thermal_zone0
[    0.295364] ACPI: thermal: Thermal Zone [THM] (25 C)
[    0.295573] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.296243] hpet_acpi_add: no address or irqs in _CRS
[    0.307645] tpm_tis MSFT0101:00: 2.0 TPM (device-id 0xFE, rev-id 4)
[    0.343210] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    0.344792] i8042: Warning: Keylock active
[    0.347033] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.347048] serio: i8042 AUX port at 0x60,0x64 irq 12
[    0.347205] mousedev: PS/2 mouse device common for all mice
[    0.347224] rtc_cmos 00:01: RTC can wake from S4
[    0.347993] rtc_cmos 00:01: registered as rtc0
[    0.348188] rtc_cmos 00:01: setting system clock to 2024-11-23T11:27:49 UTC (1732361269)
[    0.348210] rtc_cmos 00:01: alarms up to one month, y3k, 242 bytes nvram
[    0.348371] intel_pstate: Intel P-state driver initializing
[    0.348576] intel_pstate: HWP enabled
[    0.348808] efifb: probing for efifb
[    0.348825] efifb: framebuffer at 0x90000000, using 22500k, total 22500k
[    0.348827] efifb: mode is 3200x1800x32, linelength=12800, pages=1
[    0.348828] efifb: scrolling: redraw
[    0.348829] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.348894] Console: switching to colour frame buffer device 200x56
[    0.348951] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    0.352885] fb0: EFI VGA frame buffer device
[    0.353033] NET: Registered PF_INET6 protocol family
[    0.356988] Segment Routing with IPv6
[    0.357004] In-situ OAM (IOAM) with IPv6
[    0.357027] mip6: Mobile IPv6
[    0.357032] NET: Registered PF_PACKET protocol family
[    0.357056] mpls_gso: MPLS GSO support
[    0.357351] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.357389] microcode: Current revision: 0x000000f6
[    0.357391] microcode: Updated early from: 0x000000f0
[    0.357458] IPI shorthand broadcast: enabled
[    0.358467] sched_clock: Marking stable (352002068, 5881881)->(368432164, -10548215)
[    0.358612] registered taskstats version 1
[    0.358688] Loading compiled-in X.509 certificates
[    0.360090] Demotion targets for Node 0: null
[    0.360166] Key type .fscrypt registered
[    0.360167] Key type fscrypt-provisioning registered
[    0.364745] cryptd: max_cpu_qlen set to 1000
[    0.365536] AES CTR mode by8 optimization enabled
[    0.375235] Key type encrypted registered
[    0.375240] AppArmor: AppArmor sha256 policy hashing enabled
[    0.375657] RAS: Correctable Errors collector initialized.
[    0.385545] clk: Disabling unused clocks
[    0.386502] Freeing unused decrypted memory: 2036K
[    0.386869] Freeing unused kernel image (initmem) memory: 2868K
[    0.386883] Write protecting the kernel read-only data: 24576k
[    0.387081] Freeing unused kernel image (rodata/data gap) memory: 48K
[    0.397076] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[    0.397106] Run /init as init process
[    0.397107]   with arguments:
[    0.397108]     /init
[    0.397109]   with environment:
[    0.397110]     HOME=/
[    0.397110]     TERM=linux
[    0.397111]     BOOT_IMAGE=/vmlinuz-6.12.0-08446-g228a1157fb9f
[    0.482261] nvme nvme0: pci function 0000:3b:00.0
[    0.500039] nvme nvme0: 4/0/0 default/read/poll queues
[    0.506369]  nvme0n1: p1 p2 p3 p4
[    0.552551] device-mapper: uevent: version 1.0.3
[    0.552697] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel at lists.linux.dev
[    1.278147] tsc: Refined TSC clocksource calibration: 2904.008 MHz
[    1.278175] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x29dc0d988f1, max_idle_ns: 440795328788 ns
[    1.278236] clocksource: Switched to clocksource tsc
[    9.920490] PM: Image not found (code -22)
[   10.056528] EXT4-fs (dm-0): mounted filesystem 32e29882-d94d-4a92-9ee4-4d03002bfa29 ro with ordered data mode. Quota mode: none.
[   10.164851] systemd[1]: Inserted module 'autofs4'
[   10.208075] systemd[1]: systemd 257~rc2-3 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +IPE +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +BTF -XKBCOMMON -UTMP +SYSVINIT +LIBARCHIVE)
[   10.208093] systemd[1]: Detected architecture x86-64.
[   10.211220] systemd[1]: Hostname set to <abreu>.
[   10.376019] systemd[1]: bpf-restrict-fs: LSM BPF program attached
[   10.400403] systemd-ssh-generator[370]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[   10.400409] systemd-ssh-generator[370]: ? connect via 'ssh .host' locally
[   10.407539] systemd-sysv-generator[372]: SysV service '/etc/init.d/xl2tpd' lacks a native systemd unit file, automatically generating a unit file for compatibility.
[   10.407544] systemd-sysv-generator[372]: Please update package to include a native systemd unit file.
[   10.407546] systemd-sysv-generator[372]: ! This compatibility logic is deprecated, expect removal soon. !
[   10.541089] systemd[1]: Queued start job for default target graphical.target.
[   10.562836] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[   10.563150] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[   10.563416] systemd[1]: Created slice system-systemd\x2dcryptsetup.slice - Encrypted Volume Units Service Slice.
[   10.563672] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck.
[   10.563840] systemd[1]: Created slice user.slice - User and Session Slice.
[   10.563893] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch.
[   10.563928] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[   10.564078] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point.
[   10.564097] systemd[1]: Expecting device dev-disk-by\x2ddiskseq-1\x2dpart4.device - /dev/disk/by-diskseq/1-part4...
[   10.564105] systemd[1]: Expecting device dev-disk-by\x2duuid-2d23fd4c\x2d5d03\x2d4e1a\x2d8a42\x2d0e859d1f00d8.device - /dev/disk/by-uuid/2d23fd4c-5d03-4e1a-8a42-0e859d1f00d8...
[   10.564112] systemd[1]: Expecting device dev-disk-by\x2duuid-61be8f50\x2d69c5\x2d49a5\x2dbcad\x2d3f4521e9c7b5.device - /dev/disk/by-uuid/61be8f50-69c5-49a5-bcad-3f4521e9c7b5...
[   10.564117] systemd[1]: Expecting device dev-disk-by\x2duuid-96BD\x2d5653.device - /dev/disk/by-uuid/96BD-5653...
[   10.564137] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[   10.564160] systemd[1]: Reached target nss-user-lookup.target - User and Group Name Lookups.
[   10.564171] systemd[1]: Reached target paths.target - Path Units.
[   10.564186] systemd[1]: Reached target remote-fs.target - Remote File Systems.
[   10.564193] systemd[1]: Reached target slices.target - Slice Units.
[   10.564220] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[   10.566251] systemd[1]: Listening on systemd-coredump.socket - Process Core Dump Socket.
[   10.567179] systemd[1]: Listening on systemd-creds.socket - Credential Encryption/Decryption.
[   10.567247] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[   10.567319] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[   10.567394] systemd[1]: Listening on systemd-journald.socket - Journal Sockets.
[   10.567430] systemd[1]: systemd-pcrextend.socket - TPM PCR Measurements was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.567445] systemd[1]: systemd-pcrlock.socket - Make TPM PCR Policy was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.567503] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[   10.567547] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[   10.568863] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System...
[   10.569366] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
[   10.570715] systemd[1]: Mounting run-lock.mount - Legacy Locks Directory /run/lock...
[   10.574034] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
[   10.575319] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System...
[   10.579880] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
[   10.581209] systemd[1]: Starting modprobe at configfs.service - Load Kernel Module configfs...
[   10.582514] systemd[1]: Starting modprobe at drm.service - Load Kernel Module drm...
[   10.586106] systemd[1]: Starting modprobe at efi_pstore.service - Load Kernel Module efi_pstore...
[   10.587244] systemd[1]: Starting modprobe at fuse.service - Load Kernel Module fuse...
[   10.587361] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[   10.587426] systemd[1]: systemd-hibernate-clear.service - Clear Stale Hibernate Storage Info was skipped because of an unmet condition check (ConditionPathExists=/sys/firmware/efi/efivars/HibernateLocation-8cf2644b-4b0b-428f-9387-6d876050dc67).
[   10.592906] systemd[1]: Starting systemd-journald.service - Journal Service...
[   10.598234] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
[   10.598269] systemd[1]: systemd-pcrmachine.service - TPM PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.599423] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
[   10.599493] systemd[1]: systemd-tpm2-setup-early.service - Early TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.602053] systemd[1]: Starting systemd-udev-load-credentials.service - Load udev Rules from Credentials...
[   10.603152] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[   10.605421] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System.
[   10.605545] systemd[1]: Mounted dev-mqueue.mount - POSIX Message Queue File System.
[   10.605640] systemd[1]: Mounted run-lock.mount - Legacy Locks Directory /run/lock.
[   10.605738] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System.
[   10.605832] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System.
[   10.606742] pstore: Using crash dump compression: deflate
[   10.613007] pstore: Registered efi_pstore as persistent store backend
[   10.614080] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes.
[   10.615164] systemd[1]: modprobe at configfs.service: Deactivated successfully.
[   10.615428] systemd[1]: Finished modprobe at configfs.service - Load Kernel Module configfs.
[   10.616300] systemd[1]: modprobe at fuse.service: Deactivated successfully.
[   10.616465] systemd[1]: Finished modprobe at fuse.service - Load Kernel Module fuse.
[   10.622004] systemd[1]: Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
[   10.625130] systemd[1]: Mounting sys-kernel-config.mount - Kernel Configuration File System...
[   10.626798] ACPI: bus type drm_connector registered
[   10.631186] systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully...
[   10.632221] systemd[1]: modprobe at drm.service: Deactivated successfully.
[   10.632442] systemd[1]: Finished modprobe at drm.service - Load Kernel Module drm.
[   10.632740] systemd[1]: modprobe at efi_pstore.service: Deactivated successfully.
[   10.632923] systemd[1]: Finished modprobe at efi_pstore.service - Load Kernel Module efi_pstore.
[   10.636805] systemd[1]: Finished systemd-udev-load-credentials.service - Load udev Rules from Credentials.
[   10.637622] systemd[1]: Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[   10.637746] systemd[1]: Mounted sys-kernel-config.mount - Kernel Configuration File System.
[   10.638386] lp: driver loaded but no devices found
[   10.641570] ppdev: user-space parallel port driver
[   10.647329] EXT4-fs (dm-0): re-mounted 32e29882-d94d-4a92-9ee4-4d03002bfa29 r/w. Quota mode: none.
[   10.648124] systemd-journald[386]: Collecting audit messages is disabled.
[   10.648529] systemd[1]: Finished systemd-remount-fs.service - Remount Root and Kernel File Systems.
[   10.648911] systemd[1]: systemd-hwdb-update.service - Rebuild Hardware Database was skipped because of an unmet condition check (ConditionNeedsUpdate=/etc).
[   10.648968] systemd[1]: systemd-pstore.service - Platform Persistent Storage Archival was skipped because of an unmet condition check (ConditionDirectoryNotEmpty=/sys/fs/pstore).
[   10.650226] systemd[1]: Starting systemd-random-seed.service - Load/Save OS Random Seed...
[   10.650276] systemd[1]: systemd-tpm2-setup.service - TPM SRK Setup was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.655810] systemd[1]: Finished systemd-modules-load.service - Load Kernel Modules.
[   10.656860] systemd[1]: Starting systemd-sysctl.service - Apply Kernel Variables...
[   10.665569] systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service - Create Static Device Nodes in /dev gracefully.
[   10.665750] systemd[1]: systemd-sysusers.service - Create System Users was skipped because no trigger condition checks were met.
[   10.670379] systemd[1]: Starting systemd-tmpfiles-setup-dev.service - Create Static Device Nodes in /dev...
[   10.674128] systemd[1]: Finished systemd-random-seed.service - Load/Save OS Random Seed.
[   10.674585] systemd[1]: Finished systemd-sysctl.service - Apply Kernel Variables.
[   10.681591] systemd[1]: Started systemd-journald.service - Journal Service.
[   10.696545] systemd-journald[386]: Received client request to flush runtime journal.
[   10.842881] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[   10.856244] ACPI: bus type USB registered
[   10.857370] usbcore: registered new interface driver usbfs
[   10.857387] usbcore: registered new interface driver hub
[   10.857401] usbcore: registered new device driver usb
[   10.859236] ACPI: button: Lid Switch [LID0]
[   10.859294] input: Intel HID events as /devices/platform/INT33D5:00/input/input3
[   10.859317] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[   10.864093] intel-hid INT33D5:00: platform supports 5 button array
[   10.865272] input: Intel HID 5 button array as /devices/platform/INT33D5:00/input/input5
[   10.866877] ACPI: button: Power Button [PBTN]
[   10.868633] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input6
[   10.870039] ACPI: AC: AC Adapter [AC] (off-line)
[   10.870472] ACPI: button: Sleep Button [SBTN]
[   10.874109] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
[   10.879220] wmi_bus wmi_bus-PNP0C14:01: [Firmware Bug]: WQBC data block query control method not found
[   10.880682] ACPI: button: Power Button [PWRF]
[   10.881396] Consider using thermal netlink events interface
[   10.881723] input: Intel Virtual Buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/INT33D6:00/input/input8
[   10.920251] Adding 8387904k swap on /dev/nvme0n1p4.  Priority:-2 extents:1 across:8387904k SS
[   10.936526] hid: raw HID events driver (C) Jiri Kosina
[   10.942078] ACPI: battery: Slot [BAT0] (battery present)
[   10.962807] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002)
[   10.965765] idma64 idma64.0: Found Intel integrated DMA 64-bit
[   10.965820] intel_pmc_core INT33A1:00:  initialized
[   10.966210] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   10.968591] mei_me 0000:00:16.0: enabling device (0000 -> 0002)
[   10.968915] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[   10.968943] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[   10.969652] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[   10.971130] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000081109810
[   10.974168] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   10.974177] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[   10.974183] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[   10.974238] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[   10.974243] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   10.974245] usb usb1: Product: xHCI Host Controller
[   10.974247] usb usb1: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[   10.974249] usb usb1: SerialNumber: 0000:00:14.0
[   10.975214] hub 1-0:1.0: USB hub found
[   10.975236] hub 1-0:1.0: 12 ports detected
[   10.978783] input: PC Speaker as /devices/platform/pcspkr/input/input10
[   11.000834] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[   11.000842] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.000844] usb usb2: Product: xHCI Host Controller
[   11.000846] usb usb2: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[   11.000848] usb usb2: SerialNumber: 0000:00:14.0
[   11.002758] hub 2-0:1.0: USB hub found
[   11.002788] hub 2-0:1.0: 6 ports detected
[   11.051175] intel_rapl_common: Found RAPL domain package
[   11.051180] intel_rapl_common: Found RAPL domain core
[   11.051182] intel_rapl_common: Found RAPL domain uncore
[   11.051183] intel_rapl_common: Found RAPL domain dram
[   11.051184] intel_rapl_common: Found RAPL domain psys
[   11.069368] proc_thermal 0000:00:04.0: enabling device (0000 -> 0002)
[   11.075558] RAPL PMU: API unit is 2^-32 Joules, 5 fixed counters, 655360 ms ovfl timer
[   11.075564] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[   11.075565] RAPL PMU: hw unit of domain package 2^-14 Joules
[   11.075567] RAPL PMU: hw unit of domain dram 2^-14 Joules
[   11.075568] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[   11.075570] RAPL PMU: hw unit of domain psys 2^-14 Joules
[   11.094804] intel_rapl_common: Found RAPL domain package
[   11.094809] intel_rapl_common: Found RAPL domain dram
[   11.151272] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   11.162907] iTCO_vendor_support: vendor-support=0
[   11.172863] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   11.173313] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
[   11.175929] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[   11.176110] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002)
[   11.176577] idma64 idma64.1: Found Intel integrated DMA 64-bit
[   11.253895] usb 1-3: new full-speed USB device number 2 using xhci_hcd
[   11.399577] usb 1-3: New USB device found, idVendor=0cf3, idProduct=e300, bcdDevice= 0.01
[   11.399582] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   11.518212] usb 1-4: new full-speed USB device number 3 using xhci_hcd
[   11.527347] input: Dell WMI hotkeys as /devices/platform/PNP0C14:01/wmi_bus/wmi_bus-PNP0C14:01/9DBB5994-A997-11DA-B012-B622A1EF5492/input/input11
[   11.536816] Setting dangerous option enable_guc - tainting kernel
[   11.536824] Setting dangerous option enable_fbc - tainting kernel
[   11.537995] stackdepot: allocating hash table of 1048576 entries via kvcalloc
[   11.540683] i915 0000:00:02.0: [drm] Found kabylake/ult (device ID 5916) display version 9.00 stepping B0
[   11.541482] Console: switching to colour dummy device 80x25
[   11.541552] i915 0000:00:02.0: vgaarb: deactivate vga console
[   11.547105] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[   11.549353] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
[   11.598772] ACPI: battery: new extension: Dell Primary Battery Extension
[   11.620743] iTCO_wdt iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[   11.625629] iTCO_wdt iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.626140] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)
[   11.634535] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[   11.634544] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[   11.637020] EXT4-fs (nvme0n1p2): mounted filesystem 2d23fd4c-5d03-4e1a-8a42-0e859d1f00d8 r/w with ordered data mode. Quota mode: none.
[   11.647424] input: DLL075B:01 06CB:76AF Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input12
[   11.651659] input: DLL075B:01 06CB:76AF Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input13
[   11.651884] hid-generic 0018:06CB:76AF.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL075B:01 06CB:76AF] on i2c-DLL075B:01
[   11.657901] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[   11.657907] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[   11.657909] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[   11.663493] usb 1-4: New USB device found, idVendor=04f3, idProduct=2234, bcdDevice=11.11
[   11.663499] usb 1-4: New USB device strings: Mfr=4, Product=14, SerialNumber=0
[   11.663503] usb 1-4: Product: Touchscreen
[   11.663505] usb 1-4: Manufacturer: ELAN
[   11.680906] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[   11.723743] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0
[   11.743587] ACPI: video: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   11.745587] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input15
[   11.751918] ath10k_pci 0000:3a:00.0: enabling device (0000 -> 0002)
[   11.754549] ath10k_pci 0000:3a:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[   11.785902] usb 1-5: new high-speed USB device number 4 using xhci_hcd
[   11.816114] fbcon: i915drmfb (fb0) is primary device
[   11.817565] audit: type=1400 audit(1732361280.962:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="lsb_release" pid=544 comm="apparmor_parser"
[   11.818460] audit: type=1400 audit(1732361280.966:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=547 comm="apparmor_parser"
[   11.818465] audit: type=1400 audit(1732361280.966:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_filter" pid=547 comm="apparmor_parser"
[   11.818466] audit: type=1400 audit(1732361280.966:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="man_groff" pid=547 comm="apparmor_parser"
[   11.818468] audit: type=1400 audit(1732361280.966:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe" pid=545 comm="apparmor_parser"
[   11.818470] audit: type=1400 audit(1732361280.966:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="nvidia_modprobe//kmod" pid=545 comm="apparmor_parser"
[   11.821278] Console: switching to colour frame buffer device 200x56
[   11.826664] audit: type=1400 audit(1732361280.974:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/ipsec/charon" pid=551 comm="apparmor_parser"
[   11.829708] audit: type=1400 audit(1732361280.974:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="tcpdump" pid=549 comm="apparmor_parser"
[   11.829801] audit: type=1400 audit(1732361280.974:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="msmtp" pid=548 comm="apparmor_parser"
[   11.829805] audit: type=1400 audit(1732361280.974:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="msmtp//helpers" pid=548 comm="apparmor_parser"
[   11.841992] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
[   11.842160] input: DLL075B:01 06CB:76AF Mouse as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input16
[   11.842393] input: DLL075B:01 06CB:76AF Touchpad as /devices/pci0000:00/0000:00:15.1/i2c_designware.1/i2c-2/i2c-DLL075B:01/0018:06CB:76AF.0001/input/input17
[   11.842648] hid-multitouch 0018:06CB:76AF.0001: input,hidraw0: I2C HID v1.00 Mouse [DLL075B:01 06CB:76AF] on i2c-DLL075B:01
[   11.847294] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
[   11.934308] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
[   11.934314] snd_hda_codec_realtek hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[   11.934316] snd_hda_codec_realtek hdaudioC0D0:    hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[   11.934318] snd_hda_codec_realtek hdaudioC0D0:    mono: mono_out=0x0
[   11.934319] snd_hda_codec_realtek hdaudioC0D0:    inputs:
[   11.934321] snd_hda_codec_realtek hdaudioC0D0:      Headset Mic=0x19
[   11.934322] snd_hda_codec_realtek hdaudioC0D0:      Headphone Mic=0x1a
[   11.934323] snd_hda_codec_realtek hdaudioC0D0:      Internal Mic=0x12
[   11.994705] usb 1-5: New USB device found, idVendor=0c45, idProduct=670c, bcdDevice=56.26
[   11.994712] usb 1-5: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[   11.994715] usb 1-5: Product: Integrated_Webcam_HD
[   11.994717] usb 1-5: Manufacturer: CN09GTFMLOG008C8B7FWA01
[   11.998471] ath10k_pci 0000:3a:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1a56:1535
[   11.998478] ath10k_pci 0000:3a:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs 0 testmode 0
[   11.998938] ath10k_pci 0000:3a:00.0: firmware ver WLAN.RM.4.4.1-00309- api 6 features wowlan,ignore-otp,mfp crc32 0793bcf2
[   12.070107] mc: Linux media interface: v0.10
[   12.086738] ath10k_pci 0000:3a:00.0: board_file api 2 bmi_id N/A crc32 d2863f91
[   12.101779] input: ELAN Touchscreen as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0002/input/input20
[   12.102049] videodev: Linux video capture interface: v2.00
[   12.102875] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0002/input/input21
[   12.103311] input: ELAN Touchscreen UNKNOWN as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:04F3:2234.0002/input/input22
[   12.103642] hid-multitouch 0003:04F3:2234.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [ELAN Touchscreen] on usb-0000:00:14.0-4/input0
[   12.104173] usbcore: registered new interface driver usbhid
[   12.104176] usbhid: USB HID core driver
[   12.133668] Bluetooth: Core ver 2.22
[   12.133705] NET: Registered PF_BLUETOOTH protocol family
[   12.133707] Bluetooth: HCI device and connection manager initialized
[   12.137314] Bluetooth: HCI socket layer initialized
[   12.137322] Bluetooth: L2CAP socket layer initialized
[   12.137329] Bluetooth: SCO socket layer initialized
[   12.157855] usbcore: registered new interface driver btusb
[   12.167875] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1f.3/sound/card0/input19
[   12.167937] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24
[   12.167980] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input25
[   12.168021] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input26
[   12.168066] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input27
[   12.168407] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[   12.168409] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[   12.169280] usb 1-5: Found UVC 1.00 device Integrated_Webcam_HD (0c45:670c)
[   12.207434] ath10k_pci 0000:3a:00.0: htt-ver 3.87 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[   12.288444] ath: EEPROM regdomain: 0x6c
[   12.288449] ath: EEPROM indicates we should expect a direct regpair map
[   12.288451] ath: Country alpha2 being used: 00
[   12.288453] ath: Regpair used: 0x6c
[   12.298103] ath10k_pci 0000:3a:00.0 wlp58s0: renamed from wlan0
[   12.347128] Initializing XFRM netlink socket
[   12.373639] IPsec XFRM device driver
[   12.422846] PPP generic driver version 2.4.2
[   12.423537] NET: Registered PF_PPPOX protocol family
[   12.434052] l2tp_core: L2TP core driver, V2.0
[   12.435005] l2tp_netlink: L2TP netlink interface
[   12.436461] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   12.538361] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[   12.567624] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   12.966729] usbcore: registered new interface driver uvcvideo
[   15.423559] rfkill: input handler disabled
[   18.310471] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[   18.310479] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[   18.316082] wlp58s0: authenticated
[   18.317930] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[   18.350546] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=2)
[   18.353149] wlp58s0: associated
[   18.371915] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[   20.118156] rfkill: input handler enabled
[   22.834656] rfkill: input handler disabled
[   72.843090] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[   74.395125] PM: suspend entry (deep)
[   74.469930] Filesystems sync: 0.074 seconds
[   74.482484] Freezing user space processes
[   74.484519] Freezing user space processes completed (elapsed 0.002 seconds)
[   74.484530] OOM killer disabled.
[   74.484533] Freezing remaining freezable tasks
[   74.485910] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[   74.486025] printk: Suspending console(s) (use no_console_suspend to debug)
[   75.089561] ACPI: EC: interrupt blocked
[   75.123395] ACPI: PM: Preparing to enter system sleep state S3
[   75.136005] ACPI: EC: event blocked
[   75.136009] ACPI: EC: EC stopped
[   75.136011] ACPI: PM: Saving platform NVS memory
[   75.139178] Disabling non-boot CPUs ...
[   75.141155] smpboot: CPU 3 is now offline
[   75.145212] smpboot: CPU 2 is now offline
[   75.147770] smpboot: CPU 1 is now offline
[   75.156384] ACPI: PM: Low-level resume complete
[   75.156429] ACPI: EC: EC started
[   75.156429] ACPI: PM: Restoring platform NVS memory
[   75.158320] Enabling non-boot CPUs ...
[   75.158351] smpboot: Booting Node 0 Processor 1 APIC 0x2
[   75.159037] CPU1 is up
[   75.159052] smpboot: Booting Node 0 Processor 2 APIC 0x1
[   75.159802] CPU2 is up
[   75.159818] smpboot: Booting Node 0 Processor 3 APIC 0x3
[   75.160481] CPU3 is up
[   75.163348] ACPI: PM: Waking up from system sleep state S3
[   75.192764] ACPI: EC: interrupt unblocked
[   75.213520] ACPI: EC: event unblocked
[   75.216144] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[   75.216153] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[   75.226101] nvme nvme0: 4/0/0 default/read/poll queues
[   75.241944] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[   75.241948] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[   75.241951] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[   75.455292] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[   75.467507] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[   75.627524] atkbd_receive_byte: 19 callbacks suppressed
[   75.627530] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[   75.723513] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[   75.979412] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[   76.123384] OOM killer enabled.
[   76.123388] Restarting tasks ... done.
[   76.125939] random: crng reseeded on system resumption
[   76.229678] PM: suspend exit
[   76.326261] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[   76.326277] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[   76.468395] warning: `atop' uses wireless extensions which will stop working for Wi-Fi 7 hardware; use nl80211
[   76.669351] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[   76.680738] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[   76.704872] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   82.070628] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[   82.070635] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[   82.072617] wlp58s0: authenticated
[   82.074658] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[   82.105618] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=2)
[   82.108365] wlp58s0: associated
[   82.162914] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[  989.669141] Bluetooth: MGMT ver 1.23
[  989.691863] NET: Registered PF_ALG protocol family
[  989.781723] Bluetooth: RFCOMM TTY layer initialized
[  989.781750] Bluetooth: RFCOMM socket layer initialized
[  989.781772] Bluetooth: RFCOMM ver 1.11
[ 1294.913720] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[ 1296.594245] PM: suspend entry (deep)
[ 1296.611555] Filesystems sync: 0.017 seconds
[ 1296.619057] Freezing user space processes
[ 1296.620866] Freezing user space processes completed (elapsed 0.001 seconds)
[ 1296.620879] OOM killer disabled.
[ 1296.620882] Freezing remaining freezable tasks
[ 1296.622287] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 1296.622407] printk: Suspending console(s) (use no_console_suspend to debug)
[ 1297.239075] ACPI: EC: interrupt blocked
[ 1297.270277] ACPI: PM: Preparing to enter system sleep state S3
[ 1297.280838] ACPI: EC: event blocked
[ 1297.280843] ACPI: EC: EC stopped
[ 1297.280845] ACPI: PM: Saving platform NVS memory
[ 1297.284346] Disabling non-boot CPUs ...
[ 1297.287585] smpboot: CPU 3 is now offline
[ 1297.291660] smpboot: CPU 2 is now offline
[ 1297.294189] smpboot: CPU 1 is now offline
[ 1297.299650] ACPI: PM: Low-level resume complete
[ 1297.299706] ACPI: EC: EC started
[ 1297.299707] ACPI: PM: Restoring platform NVS memory
[ 1297.302203] Enabling non-boot CPUs ...
[ 1297.302240] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 1297.303180] CPU1 is up
[ 1297.303207] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 1297.304175] CPU2 is up
[ 1297.304203] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 1297.305082] CPU3 is up
[ 1297.309013] ACPI: PM: Waking up from system sleep state S3
[ 1297.348244] ACPI: EC: interrupt unblocked
[ 1297.367592] ACPI: EC: event unblocked
[ 1297.370346] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 1297.370370] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 1297.384996] nvme nvme0: 4/0/0 default/read/poll queues
[ 1297.395795] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 1297.395816] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 1297.395819] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 1297.613187] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[ 1297.621517] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 1297.781914] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[ 1297.881394] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 1298.137503] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 1298.279553] OOM killer enabled.
[ 1298.279558] Restarting tasks ... done.
[ 1298.282752] random: crng reseeded on system resumption
[ 1298.500029] PM: suspend exit
[ 1298.503235] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 1298.503250] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 1298.793199] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 1298.866188] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 1298.891255] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 1299.141668] Bluetooth: MGMT ver 1.23
[ 1340.583551] PM: suspend entry (deep)
[ 1340.603069] Filesystems sync: 0.019 seconds
[ 1340.625463] Freezing user space processes
[ 1340.628846] Freezing user space processes completed (elapsed 0.003 seconds)
[ 1340.628860] OOM killer disabled.
[ 1340.628863] Freezing remaining freezable tasks
[ 1340.631048] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[ 1340.631264] printk: Suspending console(s) (use no_console_suspend to debug)
[ 1341.218546] ACPI: EC: interrupt blocked
[ 1341.256949] ACPI: PM: Preparing to enter system sleep state S3
[ 1341.273558] ACPI: EC: event blocked
[ 1341.273563] ACPI: EC: EC stopped
[ 1341.273565] ACPI: PM: Saving platform NVS memory
[ 1341.278962] Disabling non-boot CPUs ...
[ 1341.281896] smpboot: CPU 3 is now offline
[ 1341.286511] smpboot: CPU 2 is now offline
[ 1341.291436] smpboot: CPU 1 is now offline
[ 1341.301740] ACPI: PM: Low-level resume complete
[ 1341.301784] ACPI: EC: EC started
[ 1341.301785] ACPI: PM: Restoring platform NVS memory
[ 1341.303694] Enabling non-boot CPUs ...
[ 1341.303720] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 1341.304416] CPU1 is up
[ 1341.304432] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 1341.305151] CPU2 is up
[ 1341.305166] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 1341.305981] CPU3 is up
[ 1341.308835] ACPI: PM: Waking up from system sleep state S3
[ 1341.344343] ACPI: EC: interrupt unblocked
[ 1341.384482] ACPI: EC: event unblocked
[ 1341.387615] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 1341.387634] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 1341.397011] nvme nvme0: 4/0/0 default/read/poll queues
[ 1341.412039] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 1341.412047] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 1341.412050] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 1341.633589] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 1341.657406] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[ 1341.829805] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[ 1341.889679] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 1342.145641] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 1342.285186] OOM killer enabled.
[ 1342.285191] Restarting tasks ... done.
[ 1342.289781] random: crng reseeded on system resumption
[ 1342.440128] PM: suspend exit
[ 1342.491393] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 1342.491401] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 1342.847362] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 1342.871231] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 1342.889868] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 1343.122982] Bluetooth: MGMT ver 1.23
[ 1358.368441] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port
[ 1358.368500] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1358.368519] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[ 1358.368537] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1358.368558] pci 0000:01:00.0: enabling Extended Tags
[ 1358.440751] pci 0000:01:00.0: supports D1 D2
[ 1358.440760] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1358.440886] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 1358.442904] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1358.442959] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1358.442976] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[ 1358.443014] pci 0000:02:00.0: enabling Extended Tags
[ 1358.443154] pci 0000:02:00.0: supports D1 D2
[ 1358.443157] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1358.443508] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1358.443559] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1358.443575] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[ 1358.443593] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1358.443615] pci 0000:02:01.0: enabling Extended Tags
[ 1358.443762] pci 0000:02:01.0: supports D1 D2
[ 1358.443765] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1358.444101] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1358.444152] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1358.444168] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[ 1358.444205] pci 0000:02:02.0: enabling Extended Tags
[ 1358.444345] pci 0000:02:02.0: supports D1 D2
[ 1358.444348] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1358.444688] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1358.444783] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1358.444877] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1358.445033] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint
[ 1358.445065] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[ 1358.445165] pci 0000:39:00.0: enabling Extended Tags
[ 1358.445374] pci 0000:39:00.0: supports D1 D2
[ 1358.445381] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1358.445525] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 1358.445961] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1358.446033] pci_bus 0000:02: Allocating resources
[ 1358.446063] pci 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[ 1358.446074] pci 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[ 1358.446083] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[ 1358.446094] pci 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[ 1358.446105] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1358.446111] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1358.446119] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1358.446125] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1358.446139] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1358.446146] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1358.446153] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.446158] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.446164] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.446170] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.446181] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1358.446187] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1358.446194] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.446199] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.446206] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.446212] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.446219] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1358.446231] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[ 1358.446250] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1358.446260] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[ 1358.446270] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1358.446284] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1358.446295] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[ 1358.446311] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1358.446322] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[ 1358.446331] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1358.450653] xhci_hcd 0000:39:00.0: xHCI Host Controller
[ 1358.450674] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3
[ 1358.451877] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[ 1358.452492] xhci_hcd 0000:39:00.0: xHCI Host Controller
[ 1358.452505] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4
[ 1358.452515] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[ 1358.456011] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 1358.456025] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1358.456033] usb usb3: Product: xHCI Host Controller
[ 1358.456038] usb usb3: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[ 1358.456043] usb usb3: SerialNumber: 0000:39:00.0
[ 1358.456523] hub 3-0:1.0: USB hub found
[ 1358.456550] hub 3-0:1.0: 2 ports detected
[ 1358.472190] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 1358.472208] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1358.472215] usb usb4: Product: xHCI Host Controller
[ 1358.472220] usb usb4: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[ 1358.472226] usb usb4: SerialNumber: 0000:39:00.0
[ 1358.473068] hub 4-0:1.0: USB hub found
[ 1358.473096] hub 4-0:1.0: 2 ports detected
[ 1358.475314] pci_bus 0000:02: Allocating resources
[ 1358.475345] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[ 1358.475358] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[ 1358.475367] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[ 1358.475376] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[ 1358.475387] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1358.475392] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1358.475398] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1358.475403] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1358.475415] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1358.475420] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1358.475426] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.475430] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.475435] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.475440] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.475447] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1358.475453] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1358.475459] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.475464] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.475468] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1358.475472] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1358.721205] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 1358.865624] usb 3-1: New USB device found, idVendor=2109, idProduct=2820, bcdDevice= 9.f3
[ 1358.865644] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1358.865651] usb 3-1: Product: USB2.0 Hub             
[ 1358.865657] usb 3-1: Manufacturer: VIA Labs, Inc.         
[ 1358.867681] hub 3-1:1.0: USB hub found
[ 1358.867805] hub 3-1:1.0: 5 ports detected
[ 1358.991164] usb 4-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[ 1359.009682] usb 4-1: New USB device found, idVendor=2109, idProduct=0820, bcdDevice= 9.f3
[ 1359.009713] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1359.009731] usb 4-1: Product: USB3.1 Hub             
[ 1359.009739] usb 4-1: Manufacturer: VIA Labs, Inc.         
[ 1359.016164] hub 4-1:1.0: USB hub found
[ 1359.016474] hub 4-1:1.0: 4 ports detected
[ 1359.577218] usb 3-1.1: new full-speed USB device number 3 using xhci_hcd
[ 1359.719447] usb 3-1.1: New USB device found, idVendor=06c4, idProduct=c412, bcdDevice= 0.01
[ 1359.719471] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1359.719478] usb 3-1.1: Product: DELL DA300
[ 1359.719491] usb 3-1.1: Manufacturer: Bizlink
[ 1359.719495] usb 3-1.1: SerialNumber: MCU Ver0001
[ 1359.730666] hid-generic 0003:06C4:C412.0003: hiddev1,hidraw2: USB HID v1.11 Device [Bizlink DELL DA300] on usb-0000:39:00.0-1.1/input0
[ 1359.785316] usb 4-1.2: new SuperSpeed USB device number 3 using xhci_hcd
[ 1359.801969] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00
[ 1359.801995] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 1359.802002] usb 4-1.2: Product: USB 10/100/1000 LAN
[ 1359.802016] usb 4-1.2: Manufacturer: Realtek
[ 1359.802020] usb 4-1.2: SerialNumber: 001000001
[ 1359.843091] usbcore: registered new device driver r8152-cfgselector
[ 1359.917520] r8152-cfgselector 4-1.2: reset SuperSpeed USB device number 3 using xhci_hcd
[ 1359.936407] r8152 4-1.2:1.0 (unnamed net_device) (uninitialized): Using pass-thru MAC addr 18:db:f2:2d:cc:f3
[ 1359.981989] r8152 4-1.2:1.0 eth0: v1.12.13
[ 1359.982043] usbcore: registered new interface driver r8152
[ 1359.987455] usbcore: registered new interface driver cdc_ether
[ 1359.988609] usbcore: registered new interface driver r8153_ecm
[ 1360.031190] r8152 4-1.2:1.0 enp57s0u1u2: renamed from eth0
[ 1363.175886] r8152 4-1.2:1.0 enp57s0u1u2: carrier on
[ 1601.413840] usb 3-1: USB disconnect, device number 2
[ 1601.413862] usb 3-1.1: USB disconnect, device number 3
[ 1601.481625] xhci_hcd 0000:39:00.0: xHCI host controller not responding, assume dead
[ 1601.481676] xhci_hcd 0000:39:00.0: HC died; cleaning up
[ 1601.521635] r8152 4-1.2:1.0 enp57s0u1u2: Stop submitting intr, status -108
[ 1601.550497] xhci_hcd 0000:39:00.0: remove, state 1
[ 1601.550516] usb usb4: USB disconnect, device number 1
[ 1601.618421] usb 4-1: USB disconnect, device number 2
[ 1601.618444] r8152-cfgselector 4-1.2: USB disconnect, device number 3
[ 1601.718601] xhci_hcd 0000:39:00.0: USB bus 4 deregistered
[ 1601.718648] xhci_hcd 0000:39:00.0: remove, state 1
[ 1601.718667] usb usb3: USB disconnect, device number 1
[ 1601.722725] xhci_hcd 0000:39:00.0: Host halt failed, -19
[ 1601.722752] xhci_hcd 0000:39:00.0: Host not accessible, reset failed.
[ 1601.723314] xhci_hcd 0000:39:00.0: USB bus 3 deregistered
[ 1601.780593] pci_bus 0000:02: Allocating resources
[ 1601.780655] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[ 1601.780679] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[ 1601.780694] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[ 1601.780715] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[ 1601.780737] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1601.780749] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1601.780760] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1601.780768] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1601.780791] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1601.780800] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1601.780810] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1601.780817] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1601.780826] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1601.780834] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1601.780850] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1601.780860] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1601.780872] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1601.780880] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1601.780888] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1601.780895] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1604.336015] PM: suspend entry (deep)
[ 1604.353625] Filesystems sync: 0.017 seconds
[ 1604.359614] Freezing user space processes
[ 1604.361328] Freezing user space processes completed (elapsed 0.001 seconds)
[ 1604.361333] OOM killer disabled.
[ 1604.361334] Freezing remaining freezable tasks
[ 1604.362384] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 1604.362436] printk: Suspending console(s) (use no_console_suspend to debug)
[ 1604.955540] ACPI: EC: interrupt blocked
[ 1604.986457] ACPI: PM: Preparing to enter system sleep state S3
[ 1604.999153] ACPI: EC: event blocked
[ 1604.999158] ACPI: EC: EC stopped
[ 1604.999160] ACPI: PM: Saving platform NVS memory
[ 1605.002767] Disabling non-boot CPUs ...
[ 1605.006386] smpboot: CPU 3 is now offline
[ 1605.016231] smpboot: CPU 2 is now offline
[ 1605.020555] smpboot: CPU 1 is now offline
[ 1605.028274] ACPI: PM: Low-level resume complete
[ 1605.028340] ACPI: EC: EC started
[ 1605.028340] ACPI: PM: Restoring platform NVS memory
[ 1605.030812] Enabling non-boot CPUs ...
[ 1605.030847] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 1605.031789] CPU1 is up
[ 1605.031805] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 1605.032788] CPU2 is up
[ 1605.032815] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 1605.033725] CPU3 is up
[ 1605.037649] ACPI: PM: Waking up from system sleep state S3
[ 1605.317629] ACPI: EC: interrupt unblocked
[ 1605.318251] pcieport 0000:01:00.0: Unable to change power state from unknown to D0, device inaccessible
[ 1605.326339] pcieport 0000:02:02.0: Unable to change power state from unknown to D0, device inaccessible
[ 1605.326373] pcieport 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
[ 1605.326375] pcieport 0000:02:01.0: Unable to change power state from unknown to D0, device inaccessible
[ 1605.391992] ACPI: EC: event unblocked
[ 1605.395948] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 1605.395965] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 1605.406479] nvme nvme0: 4/0/0 default/read/poll queues
[ 1605.422015] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 1605.422038] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 1605.422042] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 1605.647746] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 1605.903607] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 1606.159576] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 1606.299140] OOM killer enabled.
[ 1606.299143] Restarting tasks ... 
[ 1606.299576] pcieport 0000:02:00.0: Unable to change power state from D3cold to D0, device inaccessible
[ 1606.299887] pci_bus 0000:03: busn_res: [bus 03] is released
[ 1606.300124] pci_bus 0000:04: busn_res: [bus 04-38] is released
[ 1606.300461] pci_bus 0000:39: busn_res: [bus 39] is released
[ 1606.300760] done.
[ 1606.300768] random: crng reseeded on system resumption
[ 1606.301168] pci_bus 0000:02: busn_res: [bus 02-39] is released
[ 1606.502602] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 1606.592941] PM: suspend exit
[ 1606.596295] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 1606.596308] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 1606.956680] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 1606.989255] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 1607.229079] Bluetooth: MGMT ver 1.23
[ 1634.960372] PM: suspend entry (deep)
[ 1634.971631] Filesystems sync: 0.011 seconds
[ 1634.991353] Freezing user space processes
[ 1634.994096] Freezing user space processes completed (elapsed 0.002 seconds)
[ 1634.994107] OOM killer disabled.
[ 1634.994109] Freezing remaining freezable tasks
[ 1634.996032] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 1634.996178] printk: Suspending console(s) (use no_console_suspend to debug)
[ 1635.604247] ACPI: EC: interrupt blocked
[ 1635.643442] ACPI: PM: Preparing to enter system sleep state S3
[ 1635.658321] ACPI: EC: event blocked
[ 1635.658325] ACPI: EC: EC stopped
[ 1635.658326] ACPI: PM: Saving platform NVS memory
[ 1635.662808] Disabling non-boot CPUs ...
[ 1635.665150] smpboot: CPU 3 is now offline
[ 1635.668864] smpboot: CPU 2 is now offline
[ 1635.673812] smpboot: CPU 1 is now offline
[ 1635.681131] ACPI: PM: Low-level resume complete
[ 1635.681174] ACPI: EC: EC started
[ 1635.681175] ACPI: PM: Restoring platform NVS memory
[ 1635.683094] Enabling non-boot CPUs ...
[ 1635.683119] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 1635.683821] CPU1 is up
[ 1635.683837] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 1635.684561] CPU2 is up
[ 1635.684576] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 1635.685247] CPU3 is up
[ 1635.688125] ACPI: PM: Waking up from system sleep state S3
[ 1635.730386] ACPI: EC: interrupt unblocked
[ 1635.748389] ACPI: EC: event unblocked
[ 1635.751532] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 1635.751544] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 1635.760961] nvme nvme0: 4/0/0 default/read/poll queues
[ 1635.776364] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 1635.776372] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 1635.776376] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 1635.997827] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[ 1635.998056] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 1636.171819] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[ 1636.258107] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 1636.513959] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 1636.716946] OOM killer enabled.
[ 1636.716949] Restarting tasks ... done.
[ 1636.718794] random: crng reseeded on system resumption
[ 1636.817104] PM: suspend exit
[ 1636.921489] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 1636.921501] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 1637.186046] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 1637.275772] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 1637.303509] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 1637.546703] Bluetooth: MGMT ver 1.23
[ 1642.670457] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[ 1642.670463] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[ 1642.673812] wlp58s0: authenticated
[ 1642.677732] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[ 1642.701071] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[ 1642.704040] wlp58s0: associated
[ 1642.750065] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[ 1649.154222] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port
[ 1649.154276] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1649.154296] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[ 1649.154376] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1649.154398] pci 0000:01:00.0: enabling Extended Tags
[ 1649.154542] pci 0000:01:00.0: supports D1 D2
[ 1649.154544] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1649.154668] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 1649.155776] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1649.155827] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1649.155845] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[ 1649.155878] pci 0000:02:00.0: enabling Extended Tags
[ 1649.156022] pci 0000:02:00.0: supports D1 D2
[ 1649.156024] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1649.156398] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1649.156441] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1649.156458] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[ 1649.156478] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1649.156501] pci 0000:02:01.0: enabling Extended Tags
[ 1649.156640] pci 0000:02:01.0: supports D1 D2
[ 1649.156648] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1649.156968] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[ 1649.157018] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1649.157029] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[ 1649.157105] pci 0000:02:02.0: enabling Extended Tags
[ 1649.157246] pci 0000:02:02.0: supports D1 D2
[ 1649.157248] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1649.159170] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1649.159342] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1649.159456] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1649.159588] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint
[ 1649.159617] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[ 1649.159709] pci 0000:39:00.0: enabling Extended Tags
[ 1649.159870] pci 0000:39:00.0: supports D1 D2
[ 1649.159873] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1649.160002] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[ 1649.160263] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1649.160314] pci_bus 0000:02: Allocating resources
[ 1649.160331] pci 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[ 1649.160336] pci 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[ 1649.160339] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[ 1649.160344] pci 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[ 1649.160349] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1649.160351] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1649.160354] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1649.160356] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1649.160362] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1649.160364] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1649.160367] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.160369] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.160371] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.160374] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.160378] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1649.160380] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1649.160382] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.160384] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.160386] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.160388] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.160391] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 1649.160397] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[ 1649.160408] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[ 1649.160415] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[ 1649.160420] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1649.160427] pci 0000:02:02.0: PCI bridge to [bus 39]
[ 1649.160435] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[ 1649.160444] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[ 1649.160450] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[ 1649.160454] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[ 1649.162330] xhci_hcd 0000:39:00.0: xHCI Host Controller
[ 1649.162340] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3
[ 1649.163499] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[ 1649.166363] xhci_hcd 0000:39:00.0: xHCI Host Controller
[ 1649.166376] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4
[ 1649.166384] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[ 1649.166439] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[ 1649.166443] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1649.166444] usb usb3: Product: xHCI Host Controller
[ 1649.166446] usb usb3: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[ 1649.166448] usb usb3: SerialNumber: 0000:39:00.0
[ 1649.166753] hub 3-0:1.0: USB hub found
[ 1649.166767] hub 3-0:1.0: 2 ports detected
[ 1649.168183] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[ 1649.168189] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1649.168192] usb usb4: Product: xHCI Host Controller
[ 1649.168194] usb usb4: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[ 1649.168197] usb usb4: SerialNumber: 0000:39:00.0
[ 1649.168359] hub 4-0:1.0: USB hub found
[ 1649.168371] hub 4-0:1.0: 2 ports detected
[ 1649.179117] pci_bus 0000:02: Allocating resources
[ 1649.179138] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[ 1649.179145] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[ 1649.179149] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[ 1649.179155] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[ 1649.179160] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1649.179162] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1649.179165] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[ 1649.179167] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[ 1649.179171] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1649.179173] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1649.179176] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.179178] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.179181] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.179183] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.179186] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[ 1649.179188] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[ 1649.179191] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.179193] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.179195] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[ 1649.179197] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[ 1649.413664] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[ 1649.551928] usb 3-1: New USB device found, idVendor=2109, idProduct=2817, bcdDevice= 5.e3
[ 1649.551935] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1649.551937] usb 3-1: Product: USB2.0 Hub             
[ 1649.551939] usb 3-1: Manufacturer: VIA Labs, Inc.         
[ 1649.551940] usb 3-1: SerialNumber: 000000000
[ 1649.552911] hub 3-1:1.0: USB hub found
[ 1649.553134] hub 3-1:1.0: 5 ports detected
[ 1649.678308] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 1649.723946] usb 4-1: New USB device found, idVendor=2109, idProduct=0817, bcdDevice= 5.e3
[ 1649.723954] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1649.723957] usb 4-1: Product: USB3.0 Hub             
[ 1649.723960] usb 4-1: Manufacturer: VIA Labs, Inc.         
[ 1649.723963] usb 4-1: SerialNumber: 000000000
[ 1649.725973] hub 4-1:1.0: USB hub found
[ 1649.726131] hub 4-1:1.0: 4 ports detected
[ 1650.277626] usb 3-1.1: new high-speed USB device number 3 using xhci_hcd
[ 1650.415628] usb 3-1.1: New USB device found, idVendor=2109, idProduct=2817, bcdDevice= 7.b4
[ 1650.415641] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1650.415643] usb 3-1.1: Product: USB2.0 Hub             
[ 1650.415644] usb 3-1.1: Manufacturer: VIA Labs, Inc.         
[ 1650.415645] usb 3-1.1: SerialNumber: 000000000
[ 1650.416830] hub 3-1.1:1.0: USB hub found
[ 1650.416981] hub 3-1.1:1.0: 4 ports detected
[ 1650.509595] usb 4-1.1: new SuperSpeed USB device number 3 using xhci_hcd
[ 1650.568781] usb 4-1.1: New USB device found, idVendor=2109, idProduct=0817, bcdDevice= 7.b4
[ 1650.568790] usb 4-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1650.568793] usb 4-1.1: Product: USB3.0 Hub             
[ 1650.568795] usb 4-1.1: Manufacturer: VIA Labs, Inc.         
[ 1650.568798] usb 4-1.1: SerialNumber: 000000000
[ 1650.618495] hub 4-1.1:1.0: USB hub found
[ 1650.618651] hub 4-1.1:1.0: 4 ports detected
[ 1650.689617] usb 3-1.2: new high-speed USB device number 4 using xhci_hcd
[ 1650.845087] usb 3-1.2: New USB device found, idVendor=0bda, idProduct=5409, bcdDevice= 1.41
[ 1650.845095] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1650.845103] usb 3-1.2: Product: 4-Port USB 2.0 Hub
[ 1650.845105] usb 3-1.2: Manufacturer: Generic
[ 1650.846795] hub 3-1.2:1.0: USB hub found
[ 1650.847902] hub 3-1.2:1.0: 4 ports detected
[ 1650.906178] usb 4-1.2: new SuperSpeed USB device number 4 using xhci_hcd
[ 1650.936375] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=0409, bcdDevice= 1.41
[ 1650.936383] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1650.936386] usb 4-1.2: Product: 4-Port USB 3.0 Hub
[ 1650.936388] usb 4-1.2: Manufacturer: Generic
[ 1650.944501] hub 4-1.2:1.0: USB hub found
[ 1650.945865] hub 4-1.2:1.0: 2 ports detected
[ 1650.997628] usb 3-1.5: new high-speed USB device number 5 using xhci_hcd
[ 1651.086523] usb 3-1.5: New USB device found, idVendor=2109, idProduct=8817, bcdDevice= 0.01
[ 1651.086531] usb 3-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1651.086533] usb 3-1.5: Product: USB Billboard Device   
[ 1651.086535] usb 3-1.5: Manufacturer: VIA Labs, Inc.         
[ 1651.086542] usb 3-1.5: SerialNumber: 0000000000000001
[ 1651.157678] usb 4-1.4: new SuperSpeed USB device number 5 using xhci_hcd
[ 1651.179197] usb 4-1.4: New USB device found, idVendor=058f, idProduct=8468, bcdDevice= 1.00
[ 1651.179206] usb 4-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1651.179209] usb 4-1.4: Product: Mass Storage Device
[ 1651.179211] usb 4-1.4: Manufacturer: Generic
[ 1651.179214] usb 4-1.4: SerialNumber: 058F84688461
[ 1651.202579] SCSI subsystem initialized
[ 1651.206356] usb-storage 4-1.4:1.0: USB Mass Storage device detected
[ 1651.206551] scsi host0: usb-storage 4-1.4:1.0
[ 1651.206708] usbcore: registered new interface driver usb-storage
[ 1651.249618] usb 3-1.1.3: new high-speed USB device number 6 using xhci_hcd
[ 1651.981646] usb 3-1.2.3: new low-speed USB device number 7 using xhci_hcd
[ 1652.092419] usb 3-1.2.3: New USB device found, idVendor=413c, idProduct=2113, bcdDevice= 1.08
[ 1652.092442] usb 3-1.2.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1652.092457] usb 3-1.2.3: Product: Dell KB216 Wired Keyboard
[ 1652.103308] input: Dell KB216 Wired Keyboard as /devices/pci0000:00/0000:00:1c.0/0000:01:00.0/0000:02:02.0/0000:39:00.0/usb3/3-1/3-1.2/3-1.2.3/3-1.2.3:1.0/0003:413C:2113.0004/input/input33
[ 1652.157699] usb 4-1.1.3: new SuperSpeed USB device number 6 using xhci_hcd
[ 1652.174323] usb 4-1.1.3: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[ 1652.174338] usb 4-1.1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 1652.174343] usb 4-1.1.3: Product: USB 10/100/1000 LAN
[ 1652.174349] usb 4-1.1.3: Manufacturer: Realtek
[ 1652.174353] usb 4-1.1.3: SerialNumber: 000001
[ 1652.210166] hid-generic 0003:413C:2113.0004: input,hidraw2: USB HID v1.11 Keyboard [Dell KB216 Wired Keyboard] on usb-0000:39:00.0-1.2.3/input0
[ 1652.215370] input: Dell KB216 Wired Keyboard System Control as /devices/pci0000:00/0000:00:1c.0/0000:01:00.0/0000:02:02.0/0000:39:00.0/usb3/3-1/3-1.2/3-1.2.3/3-1.2.3:1.1/0003:413C:2113.0005/input/input34
[ 1652.254040] r8152-cfgselector 4-1.1.3: reset SuperSpeed USB device number 6 using xhci_hcd
[ 1652.270158] input: Dell KB216 Wired Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.0/0000:01:00.0/0000:02:02.0/0000:39:00.0/usb3/3-1/3-1.2/3-1.2.3/3-1.2.3:1.1/0003:413C:2113.0005/input/input35
[ 1652.270460] hid-generic 0003:413C:2113.0005: input,hidraw3: USB HID v1.11 Device [Dell KB216 Wired Keyboard] on usb-0000:39:00.0-1.2.3/input1
[ 1652.314844] r8152 4-1.1.3:1.0 eth0: v1.12.13
[ 1652.357649] usb 3-1.2.4: new low-speed USB device number 8 using xhci_hcd
[ 1652.466755] usb 3-1.2.4: New USB device found, idVendor=1bcf, idProduct=0005, bcdDevice= 0.14
[ 1652.466780] usb 3-1.2.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 1652.466788] usb 3-1.2.4: Product: USB Optical Mouse
[ 1652.477381] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1c.0/0000:01:00.0/0000:02:02.0/0000:39:00.0/usb3/3-1/3-1.2/3-1.2.4/3-1.2.4:1.0/0003:1BCF:0005.0006/input/input36
[ 1652.478008] hid-generic 0003:1BCF:0005.0006: input,hidraw4: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:39:00.0-1.2.4/input0
[ 1652.773887] usb 4-1.4: reset SuperSpeed USB device number 5 using xhci_hcd
[ 1652.806259] scsi 0:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 6
[ 1652.813621] sd 0:0:0:0: [sda] Media removed, stopped polling
[ 1652.813873] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 1652.875688] r8152 4-1.1.3:1.0 enx00e04ceabc41: renamed from eth0
[ 1656.447331] r8152 4-1.1.3:1.0 enx00e04ceabc41: carrier on
[ 1857.152294] sctp: Hash tables configured (bind 256/256)
[ 2800.082758] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[ 4105.684148] PM: suspend entry (deep)
[ 4105.702106] Filesystems sync: 0.017 seconds
[ 4105.705611] Freezing user space processes
[ 4105.707253] Freezing user space processes completed (elapsed 0.001 seconds)
[ 4105.707257] OOM killer disabled.
[ 4105.707258] Freezing remaining freezable tasks
[ 4105.708537] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 4105.708589] printk: Suspending console(s) (use no_console_suspend to debug)
[ 4106.301052] ACPI: EC: interrupt blocked
[ 4106.331651] ACPI: PM: Preparing to enter system sleep state S3
[ 4106.346295] ACPI: EC: event blocked
[ 4106.346300] ACPI: EC: EC stopped
[ 4106.346302] ACPI: PM: Saving platform NVS memory
[ 4106.349858] Disabling non-boot CPUs ...
[ 4106.352032] smpboot: CPU 3 is now offline
[ 4106.357402] smpboot: CPU 2 is now offline
[ 4106.360801] smpboot: CPU 1 is now offline
[ 4106.371249] ACPI: PM: Low-level resume complete
[ 4106.371294] ACPI: EC: EC started
[ 4106.371295] ACPI: PM: Restoring platform NVS memory
[ 4106.373196] Enabling non-boot CPUs ...
[ 4106.373221] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 4106.373917] CPU1 is up
[ 4106.373932] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 4106.374653] CPU2 is up
[ 4106.374669] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 4106.375331] CPU3 is up
[ 4106.378204] ACPI: PM: Waking up from system sleep state S3
[ 4106.681875] ACPI: EC: interrupt unblocked
[ 4106.686626] pcieport 0000:01:00.0: Unable to change power state from unknown to D0, device inaccessible
[ 4106.688466] pcieport 0000:02:02.0: Unable to change power state from unknown to D0, device inaccessible
[ 4106.688468] pcieport 0000:02:01.0: Unable to change power state from unknown to D0, device inaccessible
[ 4106.688470] pcieport 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
[ 4106.693284] xhci_hcd 0000:39:00.0: Unable to change power state from D3hot to D0, device inaccessible
[ 4106.756160] ACPI: EC: event unblocked
[ 4106.757098] xhci_hcd 0000:39:00.0: Unable to change power state from D3cold to D0, device inaccessible
[ 4106.757120] xhci_hcd 0000:39:00.0: Controller not ready at resume -19
[ 4106.757122] xhci_hcd 0000:39:00.0: PCI post-resume error -19!
[ 4106.757124] xhci_hcd 0000:39:00.0: HC died; cleaning up
[ 4106.757147] xhci_hcd 0000:39:00.0: PM: dpm_run_callback(): pci_pm_resume returns -19
[ 4106.757158] xhci_hcd 0000:39:00.0: PM: failed to resume async: error -19
[ 4106.757937] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 4106.757941] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 4106.767060] nvme nvme0: 4/0/0 default/read/poll queues
[ 4106.782065] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 4106.782069] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 4106.782071] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 4107.007666] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 4107.263737] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 4107.519851] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 4107.659649] xhci_hcd 0000:39:00.0: remove, state 4
[ 4107.659661] usb usb4: USB disconnect, device number 1
[ 4107.659667] usb 4-1: USB disconnect, device number 2
[ 4107.659672] usb 4-1.1: USB disconnect, device number 3
[ 4107.659677] r8152-cfgselector 4-1.1.3: USB disconnect, device number 6
[ 4107.659819] OOM killer enabled.
[ 4107.659824] Restarting tasks ... 
[ 4107.659952] usb 3-1: USB disconnect, device number 2
[ 4107.659962] usb 3-1.1: USB disconnect, device number 3
[ 4107.661022] done.
[ 4107.661037] random: crng reseeded on system resumption
[ 4107.661385] usb 3-1.2: USB disconnect, device number 4
[ 4107.661396] usb 3-1.2.3: USB disconnect, device number 7
[ 4107.729091] usb 4-1.2: USB disconnect, device number 4
[ 4107.730971] usb 4-1.4: USB disconnect, device number 5
[ 4107.847421] PM: suspend exit
[ 4107.864098] xhci_hcd 0000:39:00.0: USB bus 4 deregistered
[ 4107.864133] xhci_hcd 0000:39:00.0: remove, state 4
[ 4107.864144] usb usb3: USB disconnect, device number 1
[ 4107.868391] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 4107.899064] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 4107.899079] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 4107.993593] usb 3-1.2.4: USB disconnect, device number 8
[ 4108.050389] usb 3-1.5: USB disconnect, device number 5
[ 4108.061931] xhci_hcd 0000:39:00.0: Host halt failed, -19
[ 4108.061954] xhci_hcd 0000:39:00.0: Host not accessible, reset failed.
[ 4108.063304] xhci_hcd 0000:39:00.0: USB bus 3 deregistered
[ 4108.072588] pcieport 0000:02:00.0: Unable to change power state from D3cold to D0, device inaccessible
[ 4108.080498] pci_bus 0000:03: busn_res: [bus 03] is released
[ 4108.123448] pci_bus 0000:04: busn_res: [bus 04-38] is released
[ 4108.124817] pci_bus 0000:39: busn_res: [bus 39] is released
[ 4108.124962] pci_bus 0000:02: busn_res: [bus 02-39] is released
[ 4108.254613] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 4108.277249] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 4108.582534] Bluetooth: MGMT ver 1.23
[ 5429.536616] perf: interrupt took too long (2614 > 2500), lowering kernel.perf_event_max_sample_rate to 76500
[ 5429.550730] perf: interrupt took too long (3326 > 3267), lowering kernel.perf_event_max_sample_rate to 60000
[ 5429.562555] perf: interrupt took too long (4176 > 4157), lowering kernel.perf_event_max_sample_rate to 47750
[ 5429.633986] perf: interrupt took too long (5401 > 5220), lowering kernel.perf_event_max_sample_rate to 37000
[ 5429.650389] perf: interrupt took too long (6789 > 6751), lowering kernel.perf_event_max_sample_rate to 29250
[ 5429.683380] perf: interrupt took too long (8487 > 8486), lowering kernel.perf_event_max_sample_rate to 23500
[ 5430.026730] perf: interrupt took too long (10659 > 10608), lowering kernel.perf_event_max_sample_rate to 18750
[ 5430.088868] perf: interrupt took too long (13354 > 13323), lowering kernel.perf_event_max_sample_rate to 14750
[ 5430.527824] perf: interrupt took too long (16696 > 16692), lowering kernel.perf_event_max_sample_rate to 11750
[ 5430.946673] perf: interrupt took too long (21104 > 20870), lowering kernel.perf_event_max_sample_rate to 9250
[ 6131.393450] PM: suspend entry (deep)
[ 6131.398207] Filesystems sync: 0.004 seconds
[ 6131.404906] Freezing user space processes
[ 6131.414555] Freezing user space processes completed (elapsed 0.009 seconds)
[ 6131.414588] OOM killer disabled.
[ 6131.414613] Freezing remaining freezable tasks
[ 6131.417336] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[ 6131.417442] printk: Suspending console(s) (use no_console_suspend to debug)
[ 6132.003743] PM: suspend of devices complete after 545.619 msecs
[ 6132.003765] PM: start suspend of devices complete after 586.200 msecs
[ 6132.031166] PM: late suspend of devices complete after 27.386 msecs
[ 6132.038947] ACPI: EC: interrupt blocked
[ 6132.096874] PM: noirq suspend of devices complete after 65.158 msecs
[ 6132.096905] ACPI: PM: Preparing to enter system sleep state S3
[ 6132.259964] ACPI: EC: event blocked
[ 6132.259982] ACPI: EC: EC stopped
[ 6132.260000] ACPI: PM: Saving platform NVS memory
[ 6132.261653] Disabling non-boot CPUs ...
[ 6132.263526] smpboot: CPU 3 is now offline
[ 6132.269798] smpboot: CPU 2 is now offline
[ 6132.274345] smpboot: CPU 1 is now offline
[ 6132.277338] Checking wakeup interrupts
[ 6132.277359] Calling kvm_suspend+0x0/0x30 [kvm]
[ 6132.277441] Calling intel_epb_save+0x0/0x30
[ 6132.277466] Calling mce_syscore_suspend+0x0/0x20
[ 6132.277488] Calling ledtrig_cpu_syscore_suspend+0x0/0x30
[ 6132.277515] Calling timekeeping_suspend+0x0/0x2e0
[ 6132.277673] Calling save_ioapic_entries+0x0/0xd0
[ 6132.278913] Calling i8259A_suspend+0x0/0x30
[ 6132.278943] Calling fw_suspend+0x0/0x20
[ 6132.278965] Calling acpi_save_bm_rld+0x0/0x20
[ 6132.278995] Calling lapic_suspend+0x0/0x190
[ 6132.282267] ACPI: PM: Low-level resume complete
[ 6132.282328] ACPI: EC: EC started
[ 6132.282332] ACPI: PM: Restoring platform NVS memory
[ 6132.283600] Calling init_counter_refs+0x0/0x40
[ 6132.283632] Calling lapic_resume+0x0/0x210
[ 6132.283707] Calling acpi_restore_bm_rld+0x0/0x70
[ 6132.283744] Calling irqrouter_resume+0x0/0x50
[ 6132.283773] Calling i8259A_resume+0x0/0x30
[ 6132.283971] Calling ioapic_resume+0x0/0xb0
[ 6132.284240] Calling irq_pm_syscore_resume+0x0/0x20
[ 6132.284968] Calling timekeeping_resume+0x0/0x190
[ 6132.285117] Timekeeping suspended for 15.071 seconds
[ 6132.285156] Calling ledtrig_cpu_syscore_resume+0x0/0x20
[ 6132.285177] Calling mce_syscore_resume+0x0/0x30
[ 6132.285216] Calling intel_epb_restore+0x0/0x70
[ 6132.285236] Calling microcode_bsp_resume+0x0/0xc0
[ 6132.285255] Calling kvm_resume+0x0/0x30 [kvm]
[ 6132.285333] PM: Triggering wakeup from IRQ 51
[ 6132.285362] Enabling non-boot CPUs ...
[ 6132.285544] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 6132.286559] CPU1 is up
[ 6132.286735] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 6132.287947] CPU2 is up
[ 6132.288121] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 6132.289114] CPU3 is up
[ 6132.294824] ACPI: PM: Waking up from system sleep state S3
[ 6133.114082] ACPI: EC: interrupt unblocked
[ 6133.140931] PM: noirq resume of devices complete after 27.187 msecs
[ 6133.144549] PM: early resume of devices complete after 3.281 msecs
[ 6133.145303] ACPI: EC: event unblocked
[ 6133.150710] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 6133.150807] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 6133.167390] nvme nvme0: 4/0/0 default/read/poll queues
[ 6133.177859] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 6133.177887] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 6133.177911] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 6133.412057] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 6133.509648] ACPI Debug:  "iGfx Supported Functions Bitmap "
[ 6133.667863] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 6133.924401] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 6134.062495] PM: resume of devices complete after 917.943 msecs
[ 6134.080106] OOM killer enabled.
[ 6134.080136] Restarting tasks ... done.
[ 6134.099644] random: crng reseeded on system resumption
[ 6134.276042] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 6135.015930] PM: suspend exit
[ 6135.016601] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 6135.016610] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 6135.372595] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 6135.401081] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 6135.701521] Bluetooth: MGMT ver 1.23
[ 6684.647658] perf: interrupt took too long (26385 > 26380), lowering kernel.perf_event_max_sample_rate to 7500
[ 6945.194035] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6945.194771] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6945.199693] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6945.200216] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000005fe2d353
[ 6945.200448] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000008a8edd04 state to 000000005fe2d353
[ 6945.200676] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000005fe2d353
[ 6945.200886] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000008a8edd04
[ 6945.201110] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000005fe2d353
[ 6945.201324] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6945.201858] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000f28b4292 to 000000005fe2d353
[ 6945.202276] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000fe403f20 to 000000005fe2d353
[ 6945.202658] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000005fe2d353 nonblocking
[ 6945.219379] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000005fe2d353
[ 6945.219637] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000005fe2d353
[ 6945.232102] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6945.232488] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000005fe2d353
[ 6945.232622] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000008305b118 state to 000000005fe2d353
[ 6945.232733] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000005fe2d353
[ 6945.232852] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000008305b118
[ 6945.232961] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000005fe2d353
[ 6945.233102] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6945.233515] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000f28b4292 to 000000005fe2d353
[ 6945.234017] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000fe403f20 to 000000005fe2d353
[ 6945.234455] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000005fe2d353 nonblocking
[ 6945.235748] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000005fe2d353
[ 6945.236022] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000005fe2d353
[ 6945.262032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6945.262517] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6945.262908] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6945.655358] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6945.656186] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6945.661013] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6945.661439] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 00000000da80a0a4
[ 6945.661697] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000023d078bb state to 00000000da80a0a4
[ 6945.662048] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 00000000da80a0a4
[ 6945.662189] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 0000000023d078bb
[ 6945.662315] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 00000000da80a0a4
[ 6945.662476] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6945.662959] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000022beed95 to 00000000da80a0a4
[ 6945.663425] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000b2fdcdb0 to 00000000da80a0a4
[ 6945.663872] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 00000000da80a0a4 nonblocking
[ 6945.686475] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 00000000da80a0a4
[ 6945.686722] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 00000000da80a0a4
[ 6945.778105] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6945.778655] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6945.779111] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6946.256192] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6946.257018] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6946.262116] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6946.262552] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 00000000b3a8669f
[ 6946.262839] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000002df476ba state to 00000000b3a8669f
[ 6946.263016] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 00000000b3a8669f
[ 6946.263153] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000002df476ba
[ 6946.263293] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 00000000b3a8669f
[ 6946.263454] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6946.263933] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000d1577c4b to 00000000b3a8669f
[ 6946.264401] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000006fe3e0c0 to 00000000b3a8669f
[ 6946.264850] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 00000000b3a8669f nonblocking
[ 6946.287513] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 00000000b3a8669f
[ 6946.287732] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 00000000b3a8669f
[ 6946.374082] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6946.374555] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6946.374962] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6946.857206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6946.858094] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6946.862256] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6946.862648] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 00000000feca3e2d
[ 6946.862882] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000009ec22204 state to 00000000feca3e2d
[ 6946.863052] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 00000000feca3e2d
[ 6946.863175] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000009ec22204
[ 6946.863284] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 00000000feca3e2d
[ 6946.863427] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6946.863856] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000067f8dd6a to 00000000feca3e2d
[ 6946.864270] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007ed6669d to 00000000feca3e2d
[ 6946.864668] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 00000000feca3e2d nonblocking
[ 6946.887270] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 00000000feca3e2d
[ 6946.887453] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 00000000feca3e2d
[ 6946.974024] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6946.974514] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6946.974920] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6947.458590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6947.459577] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6947.488921] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 00000000c7b7a99d
[ 6947.489061] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 00000000cda771e2 state to 00000000c7b7a99d
[ 6947.489190] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 000000001e349f99 state to 00000000c7b7a99d
[ 6947.489287] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:32:plane 1A] state 00000000cda771e2
[ 6947.489404] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:32:plane 1A] state 00000000cda771e2 to [NOCRTC]
[ 6947.489504] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:40:plane 2A] 00000000dcf8d3c7 state to 00000000c7b7a99d
[ 6947.489614] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:40:plane 2A] state 00000000dcf8d3c7
[ 6947.489824] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000005ccf68c9 state to 00000000c7b7a99d
[ 6947.489921] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:48:cursor A] state 000000005ccf68c9
[ 6947.490039] i915 0000:00:02.0: [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set [NOMODE] for [CRTC:53:pipe A] state 000000001e349f99
[ 6947.490139] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:54:plane 1B] 00000000845c247b state to 00000000c7b7a99d
[ 6947.490246] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:54:plane 1B] state 00000000845c247b
[ 6947.490346] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:62:plane 2B] 00000000e6920be3 state to 00000000c7b7a99d
[ 6947.490453] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:62:plane 2B] state 00000000e6920be3
[ 6947.490553] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:70:cursor B] 00000000a0a2253a state to 00000000c7b7a99d
[ 6947.490658] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:70:cursor B] state 00000000a0a2253a
[ 6947.490761] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:75:pipe B] 00000000e80e9714 state to 00000000c7b7a99d
[ 6947.490861] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:76:plane 1C] 00000000ee2ca031 state to 00000000c7b7a99d
[ 6947.490968] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:76:plane 1C] state 00000000ee2ca031
[ 6947.491066] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:84:plane 2C] 00000000efa08d80 state to 00000000c7b7a99d
[ 6947.491173] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:84:plane 2C] state 00000000efa08d80
[ 6947.491271] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:92:cursor C] 00000000c38d77d3 state to 00000000c7b7a99d
[ 6947.491377] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:92:cursor C] state 00000000c38d77d3
[ 6947.491480] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:97:pipe C] 000000000df48a63 state to 00000000c7b7a99d
[ 6947.491597] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:99:eDP-1] 0000000096e49e53 state to 00000000c7b7a99d
[ 6947.491693] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_connector [drm]] Link [CONNECTOR:99:eDP-1] state 0000000096e49e53 to [NOCRTC]
[ 6947.491794] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:107:DP-1] 00000000912d9b89 state to 00000000c7b7a99d
[ 6947.491908] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:118:DP-2] 000000001486edf7 state to 00000000c7b7a99d
[ 6947.492003] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 00000000c7b7a99d
[ 6947.492113] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] mode changed
[ 6947.492166] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] enable changed
[ 6947.492210] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] active changed
[ 6947.492257] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:99:eDP-1]
[ 6947.492316] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:99:eDP-1]
[ 6947.492364] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:107:DP-1]
[ 6947.492408] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:107:DP-1]
[ 6947.492455] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:118:DP-2]
[ 6947.492498] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:118:DP-2]
[ 6947.492555] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] needs all connectors, enable: n, active: n
[ 6947.492602] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:53:pipe A] to 00000000c7b7a99d
[ 6947.492698] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:53:pipe A] to 00000000c7b7a99d
[ 6947.492805] i915 0000:00:02.0: [drm:drm_atomic_add_encoder_bridges [drm]] Adding all bridges for [encoder:98:DDI A/PHY A] to 00000000c7b7a99d
[ 6947.492917] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
[ 6947.493344] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.active (expected yes, found no)
[ 6947.493814] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
[ 6947.494176] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
[ 6947.494541] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4348677/8388608 link 362389/524288, found tu 0, data 0/0 link 0/0)
[ 6947.494891] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
[ 6947.495235] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
[ 6947.495590] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
[ 6947.495928] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3360, found 0)
[ 6947.496278] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
[ 6947.496613] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3360, found 0)
[ 6947.496946] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
[ 6947.497295] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
[ 6947.497629] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
[ 6947.498097] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
[ 6947.498455] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
[ 6947.498805] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1808, found 0)
[ 6947.499140] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1852, found 0)
[ 6947.499474] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1852, found 0)
[ 6947.499822] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
[ 6947.500155] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3360, found 0)
[ 6947.500489] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
[ 6947.500833] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3360, found 0)
[ 6947.501165] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
[ 6947.501498] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
[ 6947.501922] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
[ 6947.502288] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
[ 6947.502622] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
[ 6947.502955] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1808, found 0)
[ 6947.503301] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1852, found 0)
[ 6947.503633] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1852, found 0)
[ 6947.503964] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
[ 6947.504307] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
[ 6947.504639] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
[ 6947.504971] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in enhanced_framing (expected yes, found no)
[ 6947.505318] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
[ 6947.505649] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 373250, found 0)
[ 6947.506070] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 373250, found 0)
[ 6947.506422] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
[ 6947.506759] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] fastset requirement not met, forcing full modeset
[ 6947.507108] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:53:pipe A] releasing DPLL 0
[ 6947.507479] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 0, off 1, on 0, ms 1
[ 6947.507868] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000b51ff828 to 00000000c7b7a99d
[ 6947.508245] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:53:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 892) -> (0 - 0), active pipes 0x1 -> 0x0
[ 6947.508624] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000050a470c3 to 00000000c7b7a99d
[ 6947.508987] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] ddb (   0 -  853) -> (   0 -    0), size  853 ->    0
[ 6947.509349] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] ddb ( 853 -  892) -> (   0 -    0), size   39 ->    0
[ 6947.509685] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
[ 6947.510097] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]   lines    0,   5,   6,   6,  10,  11,  12,  14,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6947.510436] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]  blocks   63, 113, 140, 151, 242, 277, 300, 347,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6947.510770] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] min_ddb   64, 114, 141, 152, 243, 278, 301, 348,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6947.511127] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000f7ce41ec state 000000004d9e4ff1 to 00000000c7b7a99d
[ 6947.511489] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
[ 6947.511860] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 337500 kHz, actual 337500 kHz
[ 6947.512204] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
[ 6947.512573] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: no [modeset]
[ 6947.512924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [NOFB], visible: no
[ 6947.513283] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 6947.513623] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:48:cursor A] fb: [NOFB], visible: no
[ 6947.513996] i915 0000:00:02.0: [drm:drm_atomic_commit [drm]] committing 00000000c7b7a99d
[ 6947.514180] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1
[ 6947.520146] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turning VDD on
[ 6947.520640] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000f
[ 6947.521234] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00170 AUX <- (ret=  1) 00
[ 6947.525263] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] 
[ 6947.729777] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:99:eDP-1] set backlight PWM = 0
[ 6947.730165] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
[ 6947.738211] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00600 AUX <- (ret=  1) 02
[ 6947.738279] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turn panel power off
[ 6947.738544] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 wait for panel power off time
[ 6947.738794] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000000
[ 6947.739030] i915 0000:00:02.0: [drm:spt_irq_handler [i915]] hotplug event received, stat 0x01000000, dig 0x11001010, pins 0x00000010, long 0x00000000
[ 6947.739232] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:98:DDI A/PHY A] - short
[ 6947.790040] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] Wait complete
[ 6947.790523] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
[ 6947.791097] i915 0000:00:02.0: [drm:spt_irq_handler [i915]] hotplug event received, stat 0x01000000, dig 0x12001010, pins 0x00000010, long 0x00000010
[ 6947.791592] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:98:DDI A/PHY A] - long
[ 6947.792055] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
[ 6947.792532] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:98:DDI A/PHY A]
[ 6947.792538] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:53:pipe A]
[ 6947.793189] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:98:DDI A/PHY A]
[ 6947.793181] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
[ 6947.793950] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 6947.794689] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:98:DDI A/PHY A]
[ 6947.795079] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DDI B/PHY B]
[ 6947.795434] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:108:DP-MST A]
[ 6947.795792] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:109:DP-MST B]
[ 6947.796131] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:110:DP-MST C]
[ 6947.796463] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
[ 6947.796807] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
[ 6947.797136] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
[ 6947.797464] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
[ 6947.797894] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:99:eDP-1]
[ 6947.798237] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:107:DP-1]
[ 6947.798585] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:118:DP-2]
[ 6947.798979] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:53:pipe A]
[ 6947.799456] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 00000000c7b7a99d
[ 6947.799631] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 00000000c7b7a99d
[ 6947.897374] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6947.945043] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:126]
[ 6948.070083] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6948.070552] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6948.070959] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6948.071814] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6948.232848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6948.233347] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6948.234171] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6948.235858] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6948.302736] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:126]
[ 6948.403375] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6948.503910] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:126]
[ 6948.629845] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6948.630591] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6948.631300] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6948.632473] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6948.645009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6948.645910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6948.646951] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6948.649652] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6948.687296] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000002e4e3677
[ 6948.687453] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 00000000e5293e5a state to 000000002e4e3677
[ 6948.687591] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:32:plane 1A] state 00000000e5293e5a
[ 6948.687729] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:40:plane 2A] 0000000024d06610 state to 000000002e4e3677
[ 6948.687840] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:40:plane 2A] state 0000000024d06610
[ 6948.687972] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 00000000da51591d state to 000000002e4e3677
[ 6948.688078] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:48:cursor A] state 00000000da51591d
[ 6948.688214] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 000000000c0ece64 state to 000000002e4e3677
[ 6948.688347] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:54:plane 1B] 0000000016073d35 state to 000000002e4e3677
[ 6948.688453] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:54:plane 1B] state 0000000016073d35
[ 6948.688580] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:62:plane 2B] 00000000a949b3f1 state to 000000002e4e3677
[ 6948.688687] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:62:plane 2B] state 00000000a949b3f1
[ 6948.688815] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:70:cursor B] 000000007b532533 state to 000000002e4e3677
[ 6948.688920] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:70:cursor B] state 000000007b532533
[ 6948.689052] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:75:pipe B] 00000000ddc81fb4 state to 000000002e4e3677
[ 6948.689165] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:76:plane 1C] 00000000213c1489 state to 000000002e4e3677
[ 6948.689285] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:76:plane 1C] state 00000000213c1489
[ 6948.689396] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:84:plane 2C] 0000000043d9f556 state to 000000002e4e3677
[ 6948.689516] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:84:plane 2C] state 0000000043d9f556
[ 6948.689630] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:92:cursor C] 00000000672da492 state to 000000002e4e3677
[ 6948.689890] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:92:cursor C] state 00000000672da492
[ 6948.690028] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:97:pipe C] 0000000055749b4a state to 000000002e4e3677
[ 6948.690147] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:99:eDP-1] 0000000003862e4d state to 000000002e4e3677
[ 6948.690279] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:107:DP-1] 0000000095a6bf19 state to 000000002e4e3677
[ 6948.690393] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:118:DP-2] 00000000d74dc550 state to 000000002e4e3677
[ 6948.690517] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000002e4e3677
[ 6948.690629] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:99:eDP-1]
[ 6948.690690] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:99:eDP-1]
[ 6948.690761] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:107:DP-1]
[ 6948.690811] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:107:DP-1]
[ 6948.690862] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:118:DP-2]
[ 6948.690911] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:118:DP-2]
[ 6948.691010] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000e3a8c966 to 000000002e4e3677
[ 6948.691497] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007c4178bf to 000000002e4e3677
[ 6948.691956] i915 0000:00:02.0: [drm:drm_atomic_commit [drm]] committing 000000002e4e3677
[ 6948.692244] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000002e4e3677
[ 6948.692384] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000002e4e3677
[ 6948.737208] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:126]
[ 6948.773858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6948.774695] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6948.775385] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6948.776282] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6949.023063] PM: suspend entry (deep)
[ 6949.066339] Filesystems sync: 0.043 seconds
[ 6949.070716] Freezing user space processes
[ 6949.073942] Freezing user space processes completed (elapsed 0.003 seconds)
[ 6949.073953] OOM killer disabled.
[ 6949.073959] Freezing remaining freezable tasks
[ 6949.075891] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 6949.075956] printk: Suspending console(s) (use no_console_suspend to debug)
[ 6949.118122] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6949.118398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6949.118942] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6949.119519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
[ 6949.119761] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
[ 6949.133375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
[ 6949.133868] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6949.134172] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6949.134431] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6949.135164] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6949.202481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6949.203397] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6949.203932] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
[ 6949.204537] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6949.205824] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
[ 6949.206714] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
[ 6949.207564] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
[ 6949.208398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
[ 6949.209195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
[ 6949.210235] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000023d078bb
[ 6949.210401] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000023d078bb
[ 6949.210529] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:75:pipe B] 00000000f2f6f661 state to 0000000023d078bb
[ 6949.210668] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:97:pipe C] 0000000021c2011a state to 0000000023d078bb
[ 6949.210782] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 00000000da80a0a4 state to 0000000023d078bb
[ 6949.210916] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:40:plane 2A] 000000008305b118 state to 0000000023d078bb
[ 6949.211047] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000005fe2d353 state to 0000000023d078bb
[ 6949.211251] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:54:plane 1B] 000000008a8edd04 state to 0000000023d078bb
[ 6949.211554] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:62:plane 2B] 000000002df476ba state to 0000000023d078bb
[ 6949.211706] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:70:cursor B] 00000000987b381f state to 0000000023d078bb
[ 6949.211841] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:76:plane 1C] 00000000bc38aa08 state to 0000000023d078bb
[ 6949.211952] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:84:plane 2C] 00000000d5993b46 state to 0000000023d078bb
[ 6949.212085] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:92:cursor C] 0000000064c11922 state to 0000000023d078bb
[ 6949.212201] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:99:eDP-1] 000000004506128a state to 0000000023d078bb
[ 6949.212338] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:107:DP-1] 0000000048ab237f state to 0000000023d078bb
[ 6949.212453] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:118:DP-2] 00000000eda28771 state to 0000000023d078bb
[ 6949.212590] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000094d9e486
[ 6949.212714] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 000000002be87c41 state to 0000000094d9e486
[ 6949.212846] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:53:pipe A] to 0000000094d9e486
[ 6949.212957] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:53:pipe A] to 0000000094d9e486
[ 6949.213102] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:75:pipe B] 00000000927e73a2 state to 0000000094d9e486
[ 6949.213211] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:75:pipe B] to 0000000094d9e486
[ 6949.213342] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:75:pipe B] to 0000000094d9e486
[ 6949.213461] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:97:pipe C] 0000000082b6d0dd state to 0000000094d9e486
[ 6949.213591] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:97:pipe C] to 0000000094d9e486
[ 6949.213844] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:97:pipe C] to 0000000094d9e486
[ 6949.214074] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000094d9e486
[ 6949.214249] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009790c638 to 0000000094d9e486
[ 6949.214742] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007ed6669d to 0000000094d9e486
[ 6949.215211] i915 0000:00:02.0: [drm:drm_atomic_commit [drm]] committing 0000000094d9e486
[ 6949.215551] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000094d9e486
[ 6949.215672] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000094d9e486
[ 6949.671045] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
[ 6949.671576] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
[ 6949.672067] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
[ 6949.672513] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
[ 6949.672935] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
[ 6949.673375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6949.673875] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6949.674314] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6949.675231] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6949.675969] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6949.676722] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
[ 6949.677395] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
[ 6949.677896] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:1 driver:0 kvmr:0 debug:0)
[ 6949.702369] ACPI: EC: interrupt blocked
[ 6949.742441] ACPI: PM: Preparing to enter system sleep state S3
[ 6949.812969] ACPI: EC: event blocked
[ 6949.812985] ACPI: EC: EC stopped
[ 6949.812999] ACPI: PM: Saving platform NVS memory
[ 6949.816388] Disabling non-boot CPUs ...
[ 6949.819948] smpboot: CPU 3 is now offline
[ 6949.826486] smpboot: CPU 2 is now offline
[ 6949.831235] smpboot: CPU 1 is now offline
[ 6949.841745] ACPI: PM: Low-level resume complete
[ 6949.841802] ACPI: EC: EC started
[ 6949.841805] ACPI: PM: Restoring platform NVS memory
[ 6949.843906] Enabling non-boot CPUs ...
[ 6949.843970] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 6949.844956] CPU1 is up
[ 6949.845016] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 6949.846082] CPU2 is up
[ 6949.846137] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 6949.847256] CPU3 is up
[ 6949.852962] ACPI: PM: Waking up from system sleep state S3
[ 6950.059096] ACPI: EC: interrupt unblocked
[ 6950.081331] i915 0000:00:02.0: [drm:intel_uncore_resume_early [i915]] unclaimed mmio detected on resume, clearing
[ 6950.082093] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
[ 6950.082494] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
[ 6950.082775] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
[ 6950.083039] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
[ 6950.083409] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
[ 6950.084397] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6950.084651] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6950.084901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
[ 6950.085166] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
[ 6950.085431] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
[ 6950.085682] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
[ 6950.085930] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
[ 6950.086178] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
[ 6950.088363] ACPI: EC: event unblocked
[ 6950.090287] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
[ 6950.091681] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 6950.091712] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 6950.105946] nvme nvme0: 4/0/0 default/read/poll queues
[ 6950.106396] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 9ms, freq = 100MHz, before = 100MHz, status = 0x8002F0EC, count = 0, ret = 0
[ 6950.107274] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
[ 6950.116993] i915 0000:00:02.0: [drm:intel_huc_wait_for_auth_complete [i915]] GT0: HuC: auth took 9ms, freq = 100MHz, before = 100MHz, status = 0x0000D3B0, count = 0, ret = 0
[ 6950.117434] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 6950.117458] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 6950.117479] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 6950.118592] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 6950.119218] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:53:pipe A] hw state readout: disabled
[ 6950.119678] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:75:pipe B] hw state readout: disabled
[ 6950.120125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:97:pipe C] hw state readout: disabled
[ 6950.120532] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] hw state readout: disabled, pipe A
[ 6950.120882] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
[ 6950.121187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] hw state readout: disabled, pipe A
[ 6950.121493] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] hw state readout: disabled, pipe B
[ 6950.121796] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] hw state readout: disabled, pipe B
[ 6950.122097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] hw state readout: disabled, pipe B
[ 6950.122519] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] hw state readout: disabled, pipe C
[ 6950.122786] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] hw state readout: disabled, pipe C
[ 6950.123089] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] hw state readout: disabled, pipe C
[ 6950.123392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DDI A/PHY A] hw state readout: disabled, pipe A
[ 6950.123695] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DDI B/PHY B] hw state readout: disabled, pipe A
[ 6950.123986] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DP-MST A] hw state readout: disabled, pipe A
[ 6950.124277] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST B] hw state readout: disabled, pipe B
[ 6950.124580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST C] hw state readout: disabled, pipe C
[ 6950.124888] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
[ 6950.125177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
[ 6950.125466] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
[ 6950.125733] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
[ 6950.125974] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
[ 6950.126223] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
[ 6950.126496] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
[ 6950.126741] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
[ 6950.126990] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:99:eDP-1] hw state readout: disabled
[ 6950.127246] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:107:DP-1] hw state readout: disabled
[ 6950.127496] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
[ 6950.127730] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] min_cdclk 0 kHz
[ 6950.127964] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
[ 6950.128200] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] min_cdclk 0 kHz
[ 6950.128436] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
[ 6950.128682] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] min_cdclk 0 kHz
[ 6950.128922] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] min_cdclk 0 kHz
[ 6950.129157] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] min_cdclk 0 kHz
[ 6950.129392] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
[ 6950.129636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] min_cdclk 0 kHz
[ 6950.129877] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] min_cdclk 0 kHz
[ 6950.130117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] min_cdclk 0 kHz
[ 6950.130371] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
[ 6950.140937] i915 0000:00:02.0: [drm:intel_ddi_sanitize_encoder_pll_mapping [i915]] [ENCODER:98:DDI A/PHY A] is disabled/in DSI mode with an ungated DDI clock, gate it
[ 6950.148866] i915 0000:00:02.0: [drm:intel_ddi_sanitize_encoder_pll_mapping [i915]] [ENCODER:106:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it
[ 6950.201000] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request timed out
[ 6950.201100] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201191] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201278] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201366] i915 0000:00:02.0: [drm:intel_ddi_sanitize_encoder_pll_mapping [i915]] [ENCODER:117:DDI C/PHY C] is disabled/in DSI mode with an ungated DDI clock, gate it
[ 6950.201454] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201538] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201621] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.201704] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: no [setup_hw_state]
[ 6950.201797] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:75:pipe B] enable: no [setup_hw_state]
[ 6950.201888] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:97:pipe C] enable: no [setup_hw_state]
[ 6950.201977] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
[ 6950.202070] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:53:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
[ 6950.202159] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:75:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
[ 6950.202245] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:97:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
[ 6950.202337] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000023d078bb
[ 6950.202395] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:99:eDP-1]
[ 6950.202415] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:99:eDP-1]
[ 6950.202429] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:107:DP-1]
[ 6950.202441] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:107:DP-1]
[ 6950.202454] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:118:DP-2]
[ 6950.202467] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:118:DP-2]
[ 6950.202480] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] needs all connectors, enable: n, active: n
[ 6950.202494] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:53:pipe A] to 0000000023d078bb
[ 6950.202523] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:53:pipe A] to 0000000023d078bb
[ 6950.202548] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:75:pipe B] needs all connectors, enable: n, active: n
[ 6950.202562] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:75:pipe B] to 0000000023d078bb
[ 6950.202588] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:75:pipe B] to 0000000023d078bb
[ 6950.202612] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:97:pipe C] needs all connectors, enable: n, active: n
[ 6950.202626] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:97:pipe C] to 0000000023d078bb
[ 6950.202651] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:97:pipe C] to 0000000023d078bb
[ 6950.202689] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in dpll_hw_state  
[ 6950.202788] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] expected:
[ 6950.202878] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: ctrl1: 0x0, cfgcr1: 0x0, cfgcr2: 0x0
[ 6950.202966] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] found:
[ 6950.203053] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
[ 6950.203140] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] fastset requirement not met, forcing full modeset
[ 6950.203238] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000c90faf97 to 0000000023d078bb
[ 6950.203335] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000017aa5bbb to 0000000023d078bb
[ 6950.203432] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000f7ce41ec state 0000000094eaef12 to 0000000023d078bb
[ 6950.203531] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: no [modeset]
[ 6950.203624] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [NOFB], visible: no
[ 6950.203714] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 6950.203801] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:48:cursor A] fb: [NOFB], visible: no
[ 6950.203888] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:75:pipe B] enable: no [fastset]
[ 6950.203975] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:54:plane 1B] fb: [NOFB], visible: no
[ 6950.204061] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:62:plane 2B] fb: [NOFB], visible: no
[ 6950.204147] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:70:cursor B] fb: [NOFB], visible: no
[ 6950.204233] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:97:pipe C] enable: no [fastset]
[ 6950.204318] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 1C] fb: [NOFB], visible: no
[ 6950.204404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:84:plane 2C] fb: [NOFB], visible: no
[ 6950.204490] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:92:cursor C] fb: [NOFB], visible: no
[ 6950.204575] i915 0000:00:02.0: [drm:drm_atomic_commit [drm]] committing 0000000023d078bb
[ 6950.204629] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:98:DDI A/PHY A]
[ 6950.204721] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DDI B/PHY B]
[ 6950.204810] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:108:DP-MST A]
[ 6950.204897] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:109:DP-MST B]
[ 6950.204981] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:110:DP-MST C]
[ 6950.205065] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
[ 6950.205149] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
[ 6950.205232] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
[ 6950.205314] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
[ 6950.205397] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:99:eDP-1]
[ 6950.205484] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:107:DP-1]
[ 6950.205572] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:118:DP-2]
[ 6950.205675] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:53:pipe A]
[ 6950.205770] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:75:pipe B]
[ 6950.205863] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:97:pipe C]
[ 6950.205996] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000023d078bb
[ 6950.206032] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000023d078bb
[ 6950.206073] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected
[ 6950.206430] i915 0000:00:02.0: [drm:swsci [i915]] SWSCI request already in progress
[ 6950.206530] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
[ 6950.206628] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
[ 6950.206719] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
[ 6950.206809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
[ 6950.206917] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-1]
[ 6950.206924] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
[ 6950.214377] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
[ 6950.226369] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
[ 6950.226482] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6950.226575] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6950.226664] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6950.227207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
[ 6950.350848] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 6950.610737] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 6950.870678] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 6951.078471] OOM killer enabled.
[ 6951.078479] Restarting tasks ... done.
[ 6951.081257] random: crng reseeded on system resumption
[ 6951.349926] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
[ 6951.350141] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 6951.384517] PM: suspend exit
[ 6951.386143] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 6951.386150] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 6951.746493] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 6951.759348] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
[ 6951.759624] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6951.760183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6951.772326] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 6951.781998] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6951.793115] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000002426521f
[ 6951.793224] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 00000000252c10fe state to 000000002426521f
[ 6951.793313] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 00000000252c10fe
[ 6951.793401] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000a3726bdc state to 000000002426521f
[ 6951.793479] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:32:plane 1A] state 00000000252c10fe to [CRTC:53:pipe A]
[ 6951.793562] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:40:plane 2A] 000000009141b3d7 state to 000000002426521f
[ 6951.793640] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:40:plane 2A] state 000000009141b3d7
[ 6951.793723] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 00000000dbd80645 state to 000000002426521f
[ 6951.793798] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:48:cursor A] state 00000000dbd80645
[ 6951.793881] i915 0000:00:02.0: [drm:drm_atomic_set_mode_prop_for_crtc [drm]] Set [MODE:3200x1800] for [CRTC:53:pipe A] state 00000000a3726bdc
[ 6951.793968] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:54:plane 1B] 000000000e08b49c state to 000000002426521f
[ 6951.794045] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:54:plane 1B] state 000000000e08b49c
[ 6951.794127] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:62:plane 2B] 00000000858523c2 state to 000000002426521f
[ 6951.794203] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:62:plane 2B] state 00000000858523c2
[ 6951.794284] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:70:cursor B] 0000000066e97086 state to 000000002426521f
[ 6951.795682] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:70:cursor B] state 0000000066e97086
[ 6951.795785] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:76:plane 1C] 00000000fb8820fe state to 000000002426521f
[ 6951.795875] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:76:plane 1C] state 00000000fb8820fe
[ 6951.795968] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:84:plane 2C] 000000007c7ab341 state to 000000002426521f
[ 6951.796053] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:84:plane 2C] state 000000007c7ab341
[ 6951.796146] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:92:cursor C] 00000000b3faf8e9 state to 000000002426521f
[ 6951.796229] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:92:cursor C] state 00000000b3faf8e9
[ 6951.796326] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:99:eDP-1] 00000000849ca25b state to 000000002426521f
[ 6951.796415] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_connector [drm]] Link [CONNECTOR:99:eDP-1] state 00000000849ca25b to [CRTC:53:pipe A]
[ 6951.796508] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:107:DP-1] 00000000206ac0a1 state to 000000002426521f
[ 6951.796598] i915 0000:00:02.0: [drm:drm_atomic_get_connector_state [drm]] Added [CONNECTOR:118:DP-2] 00000000ed9f0e82 state to 000000002426521f
[ 6951.796683] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000002426521f
[ 6951.796771] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] mode changed
[ 6951.796816] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] enable changed
[ 6951.796856] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] active changed
[ 6951.796899] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:99:eDP-1]
[ 6951.796940] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CONNECTOR:99:eDP-1] using [ENCODER:98:DDI A/PHY A] on [CRTC:53:pipe A]
[ 6951.796984] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:107:DP-1]
[ 6951.797024] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:107:DP-1]
[ 6951.797065] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Updating routing for [CONNECTOR:118:DP-2]
[ 6951.797105] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] Disabling [CONNECTOR:118:DP-2]
[ 6951.797143] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset [drm_kms_helper]] [CRTC:53:pipe A] needs all connectors, enable: y, active: y
[ 6951.797185] i915 0000:00:02.0: [drm:drm_atomic_add_affected_connectors [drm]] Adding all current connectors for [CRTC:53:pipe A] to 000000002426521f
[ 6951.797273] i915 0000:00:02.0: [drm:drm_atomic_add_affected_planes [drm]] Adding all current planes for [CRTC:53:pipe A] to 000000002426521f
[ 6951.797358] i915 0000:00:02.0: [drm:drm_atomic_add_encoder_bridges [drm]] Adding all bridges for [encoder:98:DDI A/PHY A] to 000000002426521f
[ 6951.797496] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:99:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
[ 6951.797878] i915 0000:00:02.0: [drm:intel_dp_compute_config_link_bpp_limits [i915]] [ENCODER:98:DDI A/PHY A][CRTC:53:pipe A] DP link limits: pixel clock 373250 kHz DSC off max lanes 4 max rate 540000 max pipe_bpp 24 max link_bpp 24.0000
[ 6951.798145] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 24 compressed 0.0000 link rate required 1119750 available 2160000
[ 6951.798664] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
[ 6951.798942] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:98:DDI A/PHY A] [CRTC:53:pipe A]
[ 6951.799244] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
[ 6951.799517] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.active (expected no, found yes)
[ 6951.799779] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
[ 6951.800043] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
[ 6951.800304] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
[ 6951.800571] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
[ 6951.800838] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
[ 6951.801103] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
[ 6951.801364] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
[ 6951.801612] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
[ 6951.801864] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
[ 6951.802110] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
[ 6951.802389] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
[ 6951.802631] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
[ 6951.802884] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
[ 6951.803142] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
[ 6951.803401] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
[ 6951.803660] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
[ 6951.803913] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
[ 6951.804161] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
[ 6951.804397] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
[ 6951.804628] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
[ 6951.804777] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
[ 6951.804925] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
[ 6951.805070] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
[ 6951.805215] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
[ 6951.805358] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
[ 6951.805501] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
[ 6951.805643] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
[ 6951.805786] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
[ 6951.805927] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
[ 6951.806082] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
[ 6951.806245] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
[ 6951.806460] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
[ 6951.806606] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in enhanced_framing (expected no, found yes)
[ 6951.806750] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
[ 6951.806892] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
[ 6951.807034] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
[ 6951.807176] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:53:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
[ 6951.807320] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:53:pipe A] fastset requirement not met, forcing full modeset
[ 6951.807478] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 0 -> 1, off 0, on 1, ms 1
[ 6951.807852] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000973242c6 to 000000002426521f
[ 6951.808027] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:53:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
[ 6951.808189] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000fe403f20 to 000000002426521f
[ 6951.808346] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] ddb (   0 -    0) -> (   0 -  853), size    0 ->  853
[ 6951.808528] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] ddb (   0 -    0) -> ( 853 -  892), size    0 ->   39
[ 6951.808671] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
[ 6951.808811] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    0,   5,   6,   6,  10,  11,  12,  14,   0,   0,    0
[ 6951.808953] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   63, 113, 140, 151, 242, 277, 300, 347,   0,   0,    0
[ 6951.809094] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   64, 114, 141, 152, 243, 278, 301, 348,   0,   0,    0
[ 6951.809237] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000f7ce41ec state 000000008df8ca99 to 000000002426521f
[ 6951.809386] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:32:plane 1A] min cdclk (373250 kHz) > [CRTC:53:pipe A] min cdclk (0 kHz)
[ 6951.809555] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
[ 6951.809736] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:75:pipe B] 000000006fcad68b state to 000000002426521f
[ 6951.809795] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:97:pipe C] 0000000082b6d0dd state to 000000002426521f
[ 6951.809838] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
[ 6951.809989] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
[ 6951.810136] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
[ 6951.810282] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:53:pipe A] allocated DPLL 0
[ 6951.810488] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc [i915]] [CRTC:53:pipe A] reserving DPLL 0
[ 6951.810649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: yes [modeset]
[ 6951.810803] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
[ 6951.810953] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
[ 6951.811099] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
[ 6951.811243] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
[ 6951.811423] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
[ 6951.811568] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
[ 6951.811711] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
[ 6951.811855] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
[ 6951.811999] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled
[ 6951.812140] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
[ 6951.812282] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
[ 6951.812423] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
[ 6951.812565] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
[ 6951.812708] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 2, length 8
[ 6951.812850] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]]     pixelformat: RGB
[ 6951.812998] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]]     colorimetry: sRGB
[ 6951.813166] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]]     bpc: 0
[ 6951.813307] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]]     dynamic range: VESA range
[ 6951.813448] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]]     content type: Not defined
[ 6951.813591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
[ 6951.813709] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
[ 6951.813829] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
[ 6951.813948] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
[ 6951.814069] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
[ 6951.814189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
[ 6951.814309] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
[ 6951.814464] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
[ 6951.814583] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
[ 6951.814702] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
[ 6951.814849] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
[ 6951.814968] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
[ 6951.815086] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x1 gamma_enable: 1 csc_enable: 0
[ 6951.815204] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 1024 entries
[ 6951.815321] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
[ 6951.815439] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 6951.815556] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 6951.815674] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
[ 6951.815790] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
[ 6951.815907] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [FB:125] 3200x1800 format = XR30 little-endian (0x30335258) modifier = 0x100000000000001, visible: yes
[ 6951.816026] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] 	rotation: 0x1, scaler: -1, scaling_filter: 0
[ 6951.816143] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] 	src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
[ 6951.816261] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
[ 6951.816377] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:48:cursor A] fb: [NOFB], visible: no
[ 6951.816524] i915 0000:00:02.0: [drm:drm_atomic_commit [drm]] committing 000000002426521f
[ 6951.817949] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
[ 6951.818367] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:98:DDI A/PHY A]
[ 6951.818567] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DDI B/PHY B]
[ 6951.818777] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:108:DP-MST A]
[ 6951.818977] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:109:DP-MST B]
[ 6951.819176] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:110:DP-MST C]
[ 6951.819367] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
[ 6951.819557] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
[ 6951.819751] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
[ 6951.819932] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
[ 6951.820134] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:107:DP-1]
[ 6951.820331] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:118:DP-2]
[ 6951.820677] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:53:pipe A]
[ 6951.820900] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
[ 6951.821123] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turn panel power on
[ 6951.821339] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 wait for panel power cycle
[ 6951.821588] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
[ 6951.821795] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] Wait complete
[ 6951.822015] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 wait for panel power on
[ 6951.822245] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000003
[ 6951.871344] i915 0000:00:02.0: [drm:spt_irq_handler [i915]] hotplug event received, stat 0x01000000, dig 0x12001010, pins 0x00000010, long 0x00000010
[ 6951.871560] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:98:DDI A/PHY A] - long
[ 6951.871750] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
[ 6951.871991] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:98:DDI A/PHY A]
[ 6952.022376] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] Wait complete
[ 6952.022722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
[ 6952.022960] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
[ 6952.023183] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turning VDD on
[ 6952.023448] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000b
[ 6952.023863] i915 0000:00:02.0: [drm:drm_dp_dpcd_probe [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret=  1) 12
[ 6952.024122] i915 0000:00:02.0: [drm:drm_dp_dpcd_read [drm_display_helper]] AUX A/DDI A/PHY A: 0x00300 AUX -> (ret=  3) 00 00 00
[ 6952.024378] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00300 AUX <- (ret=  3) 00 aa 01
[ 6952.024602] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00600 AUX <- (ret=  1) 01
[ 6952.024821] i915 0000:00:02.0: [drm:drm_dp_dpcd_probe [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret=  1) 12
[ 6952.025204] i915 0000:00:02.0: [drm:drm_dp_dpcd_read [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret= 15) 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
[ 6952.025219] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
[ 6952.026247] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
[ 6952.026600] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00107 AUX <- (ret=  2) 00 01
[ 6952.026817] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00100 AUX <- (ret=  2) 14 84
[ 6952.026833] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
[ 6952.026949] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
[ 6952.027054] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Using DP training pattern TPS1
[ 6952.027360] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00102 AUX <- (ret=  5) 21 00 00 00 00
[ 6952.027793] i915 0000:00:02.0: [drm:drm_dp_dpcd_probe [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret=  1) 12
[ 6952.028009] i915 0000:00:02.0: [drm:drm_dp_dpcd_read [drm_display_helper]] AUX A/DDI A/PHY A: 0x00202 AUX -> (ret=  6) 11 11 80 00 66 66
[ 6952.028025] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Clock recovery OK
[ 6952.028133] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
[ 6952.028232] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Using DP training pattern TPS2
[ 6952.028534] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00102 AUX <- (ret=  5) 22 00 00 00 00
[ 6952.029565] i915 0000:00:02.0: [drm:drm_dp_dpcd_probe [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret=  1) 12
[ 6952.029784] i915 0000:00:02.0: [drm:drm_dp_dpcd_read [drm_display_helper]] AUX A/DDI A/PHY A: 0x00202 AUX -> (ret=  6) 11 77 81 00 66 66
[ 6952.029799] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
[ 6952.029908] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
[ 6952.030013] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
[ 6952.030333] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00103 AUX <- (ret=  4) 0e 0e 0e 0e
[ 6952.031374] i915 0000:00:02.0: [drm:drm_dp_dpcd_probe [drm_display_helper]] AUX A/DDI A/PHY A: 0x00000 AUX -> (ret=  1) 12
[ 6952.031591] i915 0000:00:02.0: [drm:drm_dp_dpcd_read [drm_display_helper]] AUX A/DDI A/PHY A: 0x00202 AUX -> (ret=  6) 77 77 01 00 66 66
[ 6952.031606] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
[ 6952.031710] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:99:eDP-1][ENCODER:98:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
[ 6952.032017] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00102 AUX <- (ret=  1) 00
[ 6952.032357] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
[ 6952.032487] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] 
[ 6952.032590] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
[ 6952.032745] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:99:eDP-1] set backlight PWM = 1559
[ 6952.049180] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
[ 6952.049531] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00170 AUX <- (ret=  1) 04
[ 6952.049761] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00170 AUX <- (ret=  1) 05
[ 6952.049980] i915 0000:00:02.0: [drm:drm_dp_dpcd_write [drm_display_helper]] AUX A/DDI A/PHY A: 0x00600 AUX <- (ret=  1) 01
[ 6952.050028] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:99:eDP-1]
[ 6952.050149] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:53:pipe A]
[ 6952.050776] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000002426521f
[ 6952.050874] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000002426521f
[ 6952.073844] Bluetooth: MGMT ver 1.23
[ 6952.087188] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.087342] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000041dd3cea
[ 6952.087413] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 00000000852c44b5 state to 0000000041dd3cea
[ 6952.087461] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000927e73a2 state to 0000000041dd3cea
[ 6952.087519] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 00000000852c44b5
[ 6952.087580] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000041dd3cea
[ 6952.087656] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.087876] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000148e8cb6 to 0000000041dd3cea
[ 6952.088087] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000dc0c4d2a to 0000000041dd3cea
[ 6952.088263] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000041dd3cea nonblocking
[ 6952.094463] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6952.099338] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000041dd3cea
[ 6952.099441] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000041dd3cea
[ 6952.102305] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 00000000787ebcdd
[ 6952.102415] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 00000000787ebcdd
[ 6952.102479] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 00000000787ebcdd
[ 6952.102539] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6952.102601] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 00000000787ebcdd
[ 6952.102674] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.102874] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000355f7b9e to 00000000787ebcdd
[ 6952.103048] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 00000000787ebcdd
[ 6952.103227] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 00000000787ebcdd nonblocking
[ 6952.105612] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6952.115973] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 00000000787ebcdd
[ 6952.116088] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 00000000787ebcdd
[ 6952.118860] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.118933] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000007f7c9d85
[ 6952.118993] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000007f7c9d85
[ 6952.119053] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6952.119121] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.119197] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.119402] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000003a428f6 to 000000007f7c9d85
[ 6952.119601] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000297cae8c to 000000007f7c9d85
[ 6952.119763] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.125128] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.132583] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.132663] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.132763] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.132831] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000007f7c9d85
[ 6952.132889] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000007f7c9d85
[ 6952.132952] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6952.133012] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.133087] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.133298] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000d2ef2f10 to 000000007f7c9d85
[ 6952.133492] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007e11b445 to 000000007f7c9d85
[ 6952.133680] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.149299] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.149419] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.157613] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6952.157810] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.157881] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 0000000037b5d2d0
[ 6952.157945] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 0000000037b5d2d0
[ 6952.158009] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6952.158075] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.158152] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.158413] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000ad81c44b to 0000000037b5d2d0
[ 6952.158579] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000cb487a46 to 0000000037b5d2d0
[ 6952.158741] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.165980] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.166079] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.169157] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.169293] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.169339] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 0000000037b5d2d0
[ 6952.169376] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 0000000037b5d2d0
[ 6952.169411] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6952.169447] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.169490] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.169636] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006447c45e to 0000000037b5d2d0
[ 6952.169773] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000043a5b643 to 0000000037b5d2d0
[ 6952.169940] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.178556] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6952.182625] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.182717] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.182767] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.182830] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000007f7c9d85
[ 6952.182891] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000007f7c9d85
[ 6952.182952] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6952.183019] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.183098] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.183316] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009d4903f8 to 000000007f7c9d85
[ 6952.183497] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000949fd67e to 000000007f7c9d85
[ 6952.183699] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.184896] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6952.199264] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.199347] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.199490] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.199548] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000007f7c9d85
[ 6952.199585] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000007f7c9d85
[ 6952.199620] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6952.199655] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.199699] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.199836] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000000c295b00 to 000000007f7c9d85
[ 6952.199959] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 000000007f7c9d85
[ 6952.200075] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.215947] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.216033] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.658870] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.659377] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.659593] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 0000000037b5d2d0
[ 6952.659829] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 0000000037b5d2d0
[ 6952.660018] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6952.660216] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.660388] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.660873] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000005ca747d8 to 0000000037b5d2d0
[ 6952.661261] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000b825ad30 to 0000000037b5d2d0
[ 6952.661635] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.665157] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6952.684030] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.684376] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.684441] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6952.684577] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000007f7c9d85 state to 000000006da7c478
[ 6952.684691] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000006da7c478
[ 6952.684800] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000007f7c9d85
[ 6952.684913] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6952.685043] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.685476] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000d2ef2f10 to 000000006da7c478
[ 6952.685967] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000335ac251 to 000000006da7c478
[ 6952.686402] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6952.687121] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6952.700721] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6952.701057] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000001a0bddef
[ 6952.701068] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6952.701276] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000001a0bddef
[ 6952.701488] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000001a0bddef
[ 6952.701697] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6952.701912] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000001a0bddef
[ 6952.702144] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.702855] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000003a428f6 to 000000001a0bddef
[ 6952.703470] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000001c93612c to 000000001a0bddef
[ 6952.704091] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000001a0bddef nonblocking
[ 6952.717217] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000001a0bddef
[ 6952.717417] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000001a0bddef
[ 6952.754857] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.755629] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.755764] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6952.755879] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 0000000037b5d2d0
[ 6952.755987] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6952.756099] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.756231] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.756687] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000063eb1d41 to 0000000037b5d2d0
[ 6952.757131] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 0000000037b5d2d0
[ 6952.757528] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.758426] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6952.767357] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.767702] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.767721] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.767947] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000007f7c9d85
[ 6952.768151] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000007f7c9d85
[ 6952.768353] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6952.768556] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.768792] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.769436] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009493c597 to 000000007f7c9d85
[ 6952.770072] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000949fd67e to 000000007f7c9d85
[ 6952.770722] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.783904] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.784109] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.827156] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.827676] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6952.827811] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000007f7c9d85
[ 6952.827927] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000007f7c9d85
[ 6952.828036] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6952.828148] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6952.828279] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.828701] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000ac2e5429 to 000000007f7c9d85
[ 6952.829169] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000043a5b643 to 000000007f7c9d85
[ 6952.829536] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6952.829956] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6952.833999] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6952.834238] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6952.834424] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.834588] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 0000000037b5d2d0
[ 6952.834698] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6952.834804] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6952.834911] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.835036] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.835429] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000c70a436e to 0000000037b5d2d0
[ 6952.835813] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000949fd67e to 0000000037b5d2d0
[ 6952.836177] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.857964] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.858124] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.896831] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6952.897011] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.897061] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6952.897104] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 0000000037b5d2d0
[ 6952.897144] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6952.897187] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.897236] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.897402] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000880c39fb to 0000000037b5d2d0
[ 6952.897547] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 0000000037b5d2d0
[ 6952.897686] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.897935] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6952.900616] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.900672] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6952.900737] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6952.900776] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 0000000037b5d2d0
[ 6952.900815] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6952.900853] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6952.900892] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6952.900937] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6952.901090] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000880c39fb to 0000000037b5d2d0
[ 6952.901231] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 0000000037b5d2d0
[ 6952.901366] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6952.917236] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6952.917299] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.024413] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6953.024746] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.024884] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000007f7c9d85
[ 6953.025023] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000007f7c9d85
[ 6953.025146] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6953.025267] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.025415] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.025807] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000001ee2b720 to 000000007f7c9d85
[ 6953.026209] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000001c93612c to 000000007f7c9d85
[ 6953.026645] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.026901] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6953.034090] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.034184] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6953.034353] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6953.034470] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6953.034457] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.034587] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6953.034719] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6953.034862] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.035289] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000098e0eec9 to 0000000037b5d2d0
[ 6953.035697] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000335ac251 to 0000000037b5d2d0
[ 6953.036102] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6953.041876] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6953.050890] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6953.051041] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.051266] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6953.051342] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 0000000037b5d2d0
[ 6953.051418] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 0000000037b5d2d0
[ 6953.051496] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6953.051632] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6953.051721] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.051998] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006e0abd2e to 0000000037b5d2d0
[ 6953.052263] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000335ac251 to 0000000037b5d2d0
[ 6953.052552] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6953.054075] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6953.067406] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6953.067543] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.068501] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.068589] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000007f7c9d85
[ 6953.068667] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000007f7c9d85
[ 6953.068742] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6953.068818] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.068907] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.069199] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000a7e2f842 to 000000007f7c9d85
[ 6953.069480] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000001c93612c to 000000007f7c9d85
[ 6953.069783] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.084072] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.084199] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.235606] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6953.235971] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.236105] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000007f7c9d85
[ 6953.236239] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000007f7c9d85
[ 6953.236359] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6953.236498] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.236656] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.237127] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006704cc92 to 000000007f7c9d85
[ 6953.237553] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 000000007f7c9d85
[ 6953.237969] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.254104] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6953.260394] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.260637] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6953.260783] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6953.260921] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6953.261056] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6953.261072] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.261201] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6953.261364] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.261804] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000ac2e5429 to 0000000037b5d2d0
[ 6953.262230] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000949fd67e to 0000000037b5d2d0
[ 6953.262678] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6953.274477] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6953.276971] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6953.277132] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.277286] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000007f7c9d85
[ 6953.277407] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000007f7c9d85
[ 6953.277482] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6953.277460] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.277559] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.277647] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.277931] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000118f3c1f to 000000007f7c9d85
[ 6953.278196] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000043a5b643 to 000000007f7c9d85
[ 6953.278502] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.288049] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6953.293562] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.293725] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.294019] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.294167] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000007f7c9d85
[ 6953.294340] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000007f7c9d85
[ 6953.294485] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6953.294621] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.294782] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.295232] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000005bde6ab5 to 000000007f7c9d85
[ 6953.295635] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000949fd67e to 000000007f7c9d85
[ 6953.296056] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.304819] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6953.310276] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.310466] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.310754] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6953.310848] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 0000000037b5d2d0
[ 6953.310930] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 0000000037b5d2d0
[ 6953.311009] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6953.311085] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6953.311179] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.311462] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006d1f9c15 to 0000000037b5d2d0
[ 6953.311729] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 0000000037b5d2d0
[ 6953.311984] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6953.321780] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6953.327008] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6953.327168] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.327912] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6953.328061] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6953.328202] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6953.328343] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6953.328481] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6953.328647] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.329101] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006d1f9c15 to 0000000037b5d2d0
[ 6953.329543] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000a7decdf0 to 0000000037b5d2d0
[ 6953.329964] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6953.335047] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
[ 6953.335657] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
[ 6953.337785] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6953.343759] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6953.343908] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.344024] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6953.344055] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000007f7c9d85
[ 6953.344197] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000007f7c9d85
[ 6953.344338] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6953.344483] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.344644] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.345073] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000007493867f to 000000007f7c9d85
[ 6953.345491] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000b825ad30 to 000000007f7c9d85
[ 6953.345780] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.352962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
[ 6953.360397] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.360521] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.571686] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6953.571877] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6953.571954] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000007f7c9d85
[ 6953.572009] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000007f7c9d85
[ 6953.572060] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000007f7c9d85
[ 6953.572118] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6953.572175] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 0000000037b5d2d0 state to 000000007f7c9d85
[ 6953.572233] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:48:cursor A] state 0000000037b5d2d0
[ 6953.572288] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:48:cursor A] state 0000000037b5d2d0 to [CRTC:53:pipe A]
[ 6953.572322] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000007f7c9d85
[ 6953.572376] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.572565] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 0 -> 1, off 0, on 1, ms 0
[ 6953.572755] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000b2c2e268 to 000000007f7c9d85
[ 6953.572941] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000007f7c9d85
[ 6953.573114] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
[ 6953.573280] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    0,   3,   4,   4,   8,   9,  10,  12,   0,   0,    0
[ 6953.573462] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   19,  19,  19,  19,  19,  20,  22,  26,   0,   0,    0
[ 6953.573645] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   20,  20,  20,  20,  20,  21,  23,  27,   0,   0,    0
[ 6953.573831] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000007f7c9d85 nonblocking
[ 6953.579132] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:129]
[ 6953.595958] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000007f7c9d85
[ 6953.596055] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000007f7c9d85
[ 6953.596225] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6953.596308] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6953.596372] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000007f7c9d85 state to 000000006da7c478
[ 6953.596428] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000006da7c478
[ 6953.596483] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:129] for [PLANE:32:plane 1A] state 000000007f7c9d85
[ 6953.596541] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 0000000041dd3cea state to 000000006da7c478
[ 6953.596595] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:48:cursor A] state 0000000041dd3cea
[ 6953.596653] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6953.596728] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.596935] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.597117] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000463a46a2 to 000000006da7c478
[ 6953.597309] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6953.597504] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6953.612633] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6953.612719] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6953.613688] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:130]
[ 6953.614033] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6953.614107] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000037b5d2d0 state to 000000006da7c478
[ 6953.614170] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000006da7c478
[ 6953.614230] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:130] for [PLANE:32:plane 1A] state 0000000037b5d2d0
[ 6953.614294] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6953.614427] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6953.614665] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009c3d1d7c to 000000006da7c478
[ 6953.614866] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6953.615058] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6953.629293] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6953.629352] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6954.011594] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6954.011772] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000007f7c9d85 state to 000000006da7c478
[ 6954.011921] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000006da7c478
[ 6954.012048] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:48:cursor A] state 000000007f7c9d85
[ 6954.012182] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:48:cursor A] state 000000007f7c9d85 to [NOCRTC]
[ 6954.012310] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6954.012455] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 1 -> 0, off 1, on 0, ms 0
[ 6954.012984] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009c3d1d7c to 000000006da7c478
[ 6954.013499] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6954.013967] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
[ 6954.014539] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   lines    0,   3,   4,   4,   8,   9,  10,  12,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6954.015233] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]  blocks   19,  19,  19,  19,  19,  20,  22,  26,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6954.015974] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] min_ddb   20,  20,  20,  20,  20,  21,  23,  27,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6954.016750] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6954.024542] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6954.039482] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6954.039784] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6954.040166] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6954.040422] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000006da7c478
[ 6954.040688] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000006da7c478
[ 6954.040956] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6954.041228] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6954.041522] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.042629] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009c3d1d7c to 000000006da7c478
[ 6954.043439] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6954.044236] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6954.055856] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6954.056089] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6954.336154] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6954.336631] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000001a0bddef
[ 6954.336855] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 000000001a0bddef
[ 6954.337002] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000001a0bddef
[ 6954.337140] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6954.337283] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000001a0bddef
[ 6954.337450] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.337972] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000abccf711 to 000000001a0bddef
[ 6954.338573] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000dc0c4d2a to 000000001a0bddef
[ 6954.339345] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000001a0bddef nonblocking
[ 6954.362006] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000001a0bddef
[ 6954.362224] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000001a0bddef
[ 6954.371470] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6954.371940] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000001a0bddef
[ 6954.372118] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000001a0bddef
[ 6954.372269] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000001a0bddef
[ 6954.372409] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6954.372554] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000001a0bddef
[ 6954.372719] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.373255] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000abccf711 to 000000001a0bddef
[ 6954.373770] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000dc0c4d2a to 000000001a0bddef
[ 6954.374265] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000001a0bddef nonblocking
[ 6954.378508] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000001a0bddef
[ 6954.378807] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000001a0bddef
[ 6954.474999] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6954.475459] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6954.475617] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 0000000037b5d2d0
[ 6954.475763] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6954.475900] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6954.476041] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6954.476205] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.476734] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000b86f44f2 to 0000000037b5d2d0
[ 6954.477228] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000cb487a46 to 0000000037b5d2d0
[ 6954.477701] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6954.478503] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6954.478821] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6954.507067] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6954.507511] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6954.507667] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000037b5d2d0 state to 000000006da7c478
[ 6954.507812] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000006da7c478
[ 6954.507948] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000037b5d2d0
[ 6954.508087] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6954.508251] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.508768] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000005401e500 to 000000006da7c478
[ 6954.509260] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000005e4809fe to 000000006da7c478
[ 6954.509733] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6954.511811] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6954.512097] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6954.562063] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6954.562841] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000041dd3cea
[ 6954.563128] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000006da7c478 state to 0000000041dd3cea
[ 6954.563407] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000041dd3cea
[ 6954.563681] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:32:plane 1A] state 000000006da7c478
[ 6954.563958] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000041dd3cea
[ 6954.564273] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.565161] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 00000000172adbe6 to 0000000041dd3cea
[ 6954.566019] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000006e5bdb5f to 0000000041dd3cea
[ 6954.566891] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000041dd3cea nonblocking
[ 6954.578539] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000041dd3cea
[ 6954.578842] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000041dd3cea
[ 6954.597128] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6954.597571] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000001a0bddef
[ 6954.597727] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 000000001a0bddef
[ 6954.597870] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 000000001a0bddef
[ 6954.598007] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6954.598146] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000001a0bddef
[ 6954.598407] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6954.598944] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000000868e5f9 to 000000001a0bddef
[ 6954.599438] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000000384e04d to 000000001a0bddef
[ 6954.599908] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000001a0bddef nonblocking
[ 6954.611856] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000001a0bddef
[ 6954.612140] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000001a0bddef
[ 6955.058472] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:125]
[ 6955.058696] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6955.058842] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000001a0bddef state to 0000000037b5d2d0
[ 6955.058986] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:48:cursor A] state 000000001a0bddef
[ 6955.059131] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 0000000037b5d2d0
[ 6955.059254] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:48:cursor A] state 000000001a0bddef to [CRTC:53:pipe A]
[ 6955.059382] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6955.059535] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 0 -> 1, off 0, on 1, ms 0
[ 6955.060048] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000079b35c9f to 0000000037b5d2d0
[ 6955.060542] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007e11b445 to 0000000037b5d2d0
[ 6955.061228] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   level  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
[ 6955.061726] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   lines    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->    0,   3,   4,   4,   8,   9,  10,  12,   0,   0,    0
[ 6955.062159] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]  blocks    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   19,  19,  19,  19,  19,  20,  22,  26,   0,   0,    0
[ 6955.062902] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] min_ddb    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0 ->   20,  20,  20,  20,  20,  21,  23,  27,   0,   0,    0
[ 6955.063658] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6955.086614] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6955.086902] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 6955.190432] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6955.191024] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6955.191268] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000037b5d2d0 state to 000000006da7c478
[ 6955.191416] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 000000006da7c478
[ 6955.191555] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 0000000037b5d2d0
[ 6955.191700] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000007f7c9d85 state to 000000006da7c478
[ 6955.191832] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:125] for [PLANE:48:cursor A] state 000000007f7c9d85
[ 6955.191965] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6955.192147] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6955.192673] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 1 -> 1, off 0, on 0, ms 0
[ 6955.193139] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000006c0447c1 to 000000006da7c478
[ 6955.193620] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6955.194261] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6955.202426] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turning VDD off
[ 6955.203258] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000007
[ 6955.204443] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6955.204745] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6955.260347] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:124]
[ 6955.260891] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 000000006da7c478
[ 6955.261068] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 000000001a0bddef state to 000000006da7c478
[ 6955.261217] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f0d6884b state to 000000006da7c478
[ 6955.261356] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:124] for [PLANE:32:plane 1A] state 000000001a0bddef
[ 6955.261501] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 000000006da7c478
[ 6955.261667] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6955.262214] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009680c488 to 000000006da7c478
[ 6955.262944] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 0000000012d77471 to 000000006da7c478
[ 6955.263422] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 000000006da7c478 nonblocking
[ 6955.270042] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 000000006da7c478
[ 6955.270265] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 000000006da7c478
[ 6955.370478] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
[ 6955.371034] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
[ 6955.371527] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
[ 6955.648515] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000041dd3cea
[ 6955.648814] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:48:cursor A] 000000006da7c478 state to 0000000041dd3cea
[ 6955.649077] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 00000000f2f6f661 state to 0000000041dd3cea
[ 6955.649310] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [NOFB] for [PLANE:48:cursor A] state 000000006da7c478
[ 6955.649575] i915 0000:00:02.0: [drm:drm_atomic_set_crtc_for_plane [drm]] Link [PLANE:48:cursor A] state 000000006da7c478 to [NOCRTC]
[ 6955.649835] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000041dd3cea
[ 6955.650105] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:48:cursor A] visible 1 -> 0, off 1, on 0, ms 0
[ 6955.650994] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 000000009680c488 to 0000000041dd3cea
[ 6955.651750] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 00000000297cae8c to 0000000041dd3cea
[ 6955.652308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
[ 6955.652428] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm ->  wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
[ 6955.653387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
[ 6955.653444] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]   lines    0,   3,   4,   4,   8,   9,  10,  12,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6955.654499] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A]  blocks   19,  19,  19,  19,  19,  20,  22,  26,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6955.655197] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:48:cursor A] min_ddb   20,  20,  20,  20,  20,  21,  23,  27,   0,   0,    0 ->    0,   0,   0,   0,   0,   0,   0,   0,   0,   0,    0
[ 6955.655883] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000041dd3cea nonblocking
[ 6955.662031] i915 0000:00:02.0: [drm:drm_mode_addfb2 [drm]] [FB:127]
[ 6955.678644] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000041dd3cea
[ 6955.678956] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000041dd3cea
[ 6955.679259] i915 0000:00:02.0: [drm:drm_atomic_state_init [drm]] Allocated atomic state 0000000037b5d2d0
[ 6955.679524] i915 0000:00:02.0: [drm:drm_atomic_get_plane_state [drm]] Added [PLANE:32:plane 1A] 0000000041dd3cea state to 0000000037b5d2d0
[ 6955.679781] i915 0000:00:02.0: [drm:drm_atomic_get_crtc_state [drm]] Added [CRTC:53:pipe A] 0000000021c2011a state to 0000000037b5d2d0
[ 6955.680028] i915 0000:00:02.0: [drm:drm_atomic_set_fb_for_plane [drm]] Set [FB:127] for [PLANE:32:plane 1A] state 0000000041dd3cea
[ 6955.680200] i915 0000:00:02.0: [drm:drm_atomic_check_only [drm]] checking 0000000037b5d2d0
[ 6955.680366] i915 0000:00:02.0: [drm:intel_plane_atomic_check_with_state [i915]] [CRTC:53:pipe A] with [PLANE:32:plane 1A] visible 1 -> 1, off 0, on 0, ms 0
[ 6955.681020] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 00000000207a4c69 state 0000000079b35c9f to 0000000037b5d2d0
[ 6955.681773] i915 0000:00:02.0: [drm:intel_atomic_get_global_obj_state [i915]] Added new global object 0000000086a01e9a state 000000007e11b445 to 0000000037b5d2d0
[ 6955.682569] i915 0000:00:02.0: [drm:drm_atomic_nonblocking_commit [drm]] committing 0000000037b5d2d0 nonblocking
[ 6955.695362] i915 0000:00:02.0: [drm:drm_atomic_state_default_clear [drm]] Clearing atomic state 0000000037b5d2d0
[ 6955.695644] i915 0000:00:02.0: [drm:__drm_atomic_state_free [drm]] Freeing atomic state 0000000037b5d2d0
[ 9322.512992] PM: suspend entry (deep)
[ 9322.529575] Filesystems sync: 0.016 seconds
[ 9322.534195] Freezing user space processes
[ 9322.537475] Freezing user space processes completed (elapsed 0.003 seconds)
[ 9322.537486] OOM killer disabled.
[ 9322.537492] Freezing remaining freezable tasks
[ 9322.539240] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 9322.539316] printk: Suspending console(s) (use no_console_suspend to debug)
[ 9322.594328] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x663, return 0x107
[ 9322.594400] xhci_hcd 0000:00:14.0: clear USB_PORT_FEAT_SUSPEND
[ 9322.594408] usb 1-3: usb suspend, wakeup 0
[ 9322.594411] xhci_hcd 0000:00:14.0: PORTSC 0663
[ 9322.594426] xhci_hcd 0000:00:14.0: Set port 1-4 link state, portsc: 0x663, write 0x107e1
[ 9322.594445] xhci_hcd 0000:00:14.0: Port change event, 1-4, id 4, portsc: 0x4007e3
[ 9322.594461] xhci_hcd 0000:00:14.0: port resume event for port 4
[ 9322.594480] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9322.595111] usb usb2: usb auto-resume
[ 9322.595189] hub 2-0:1.0: hub_resume
[ 9322.622668] xhci_hcd 0000:00:14.0: Get port status 2-1 read: 0x2a0, return 0x2a0
[ 9322.622756] xhci_hcd 0000:00:14.0: Get port status 2-2 read: 0x2a0, return 0x2a0
[ 9322.622811] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2a0, return 0x2a0
[ 9322.622863] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x2a0, return 0x2a0
[ 9322.622913] xhci_hcd 0000:00:14.0: Get port status 2-5 read: 0x2a0, return 0x2a0
[ 9322.622963] xhci_hcd 0000:00:14.0: Get port status 2-6 read: 0x2a0, return 0x2a0
[ 9322.623021] hub 2-0:1.0: hub_suspend
[ 9322.623099] usb usb2: bus suspend, wakeup 0
[ 9322.634738] xhci_hcd 0000:00:14.0: Set port 1-4 link state, portsc: 0x7e3, write 0x10601
[ 9322.634790] xhci_hcd 0000:00:14.0: Port change event, 1-4, id 4, portsc: 0x400603
[ 9322.634808] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9322.634853] usb 1-4: usb auto-resume
[ 9322.678740] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x603, return 0x40103
[ 9322.678841] xhci_hcd 0000:00:14.0: clear port4 suspend/resume change, portsc: 0x603
[ 9322.694652] usb 1-4: Waited 0ms for CONNECT
[ 9322.694690] usb 1-4: finish resume
[ 9322.695445] xhci_hcd 0000:00:14.0: Cancel URB 00000000039f59a1, dev 4, ep 0x81, starting at offset 0x141fd5010
[ 9322.695499] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9322.695539] xhci_hcd 0000:00:14.0: Stopped on Transfer TRB for slot 2 ep 2
[ 9322.695574] xhci_hcd 0000:00:14.0: Removing canceled TD starting at 0x141fd5010 (dma) in stream 0 URB 00000000039f59a1
[ 9322.695605] xhci_hcd 0000:00:14.0: Set TR Deq ptr 0x141fd5020, cycle 1

[ 9322.695626] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9322.695645] xhci_hcd 0000:00:14.0: xhci_giveback_invalidated_tds: Keep cancelled URB 00000000039f59a1 TD as cancel_status is 2
[ 9322.695678] xhci_hcd 0000:00:14.0: Successful Set TR Deq Ptr cmd, deq = @141fd5020
[ 9322.695699] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: Giveback cancelled URB 00000000039f59a1 TD
[ 9322.695719] xhci_hcd 0000:00:14.0: Giveback URB 00000000039f59a1, len = 0, expected = 116, status = -115
[ 9322.695750] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: All TDs cleared, ring doorbell
[ 9322.696121] usb 1-4: usb suspend, wakeup 0
[ 9322.696519] hub 1-0:1.0: hub_suspend
[ 9322.696696] usb usb1: bus suspend, wakeup 0
[ 9322.696738] xhci_hcd 0000:00:14.0: port 1-4 not suspended
[ 9322.696770] xhci_hcd 0000:00:14.0: port 1-3 not suspended
[ 9322.696823] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9322.696862] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 2 ep 3
[ 9322.696896] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 2 ep 0
[ 9322.697016] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9322.697048] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 6
[ 9322.697077] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 5
[ 9322.697104] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 3
[ 9322.697129] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 1 ep 0
[ 9322.706962] xhci_hcd 0000:00:14.0: config port 2-1 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.706991] xhci_hcd 0000:00:14.0: config port 2-2 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707010] xhci_hcd 0000:00:14.0: config port 2-3 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707028] xhci_hcd 0000:00:14.0: config port 2-4 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707046] xhci_hcd 0000:00:14.0: config port 2-5 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707064] xhci_hcd 0000:00:14.0: config port 2-6 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707082] xhci_hcd 0000:00:14.0: config port 1-1 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707100] xhci_hcd 0000:00:14.0: config port 1-2 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707120] xhci_hcd 0000:00:14.0: config port 1-6 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707138] xhci_hcd 0000:00:14.0: config port 1-7 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707155] xhci_hcd 0000:00:14.0: config port 1-8 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707172] xhci_hcd 0000:00:14.0: config port 1-9 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707190] xhci_hcd 0000:00:14.0: config port 1-10 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707208] xhci_hcd 0000:00:14.0: config port 1-11 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707225] xhci_hcd 0000:00:14.0: config port 1-12 wake bits, portsc: 0x2a0, write: 0x202a0
[ 9322.707241] xhci_hcd 0000:00:14.0: xhci_suspend: stopping usb1 port polling.
[ 9322.707268] xhci_hcd 0000:00:14.0: // Setting command ring address to 0x104954001
[ 9323.167422] ACPI: EC: interrupt blocked
[ 9323.169769] xhci_hcd 0000:00:14.0: wakeup: 1
[ 9323.203022] xhci_hcd 0000:00:14.0: --> PCI D3hot
[ 9323.203137] ACPI: PM: Preparing to enter system sleep state S3
[ 9323.271652] ACPI: EC: event blocked
[ 9323.271667] ACPI: EC: EC stopped
[ 9323.271681] ACPI: PM: Saving platform NVS memory
[ 9323.274807] Disabling non-boot CPUs ...
[ 9323.278908] smpboot: CPU 3 is now offline
[ 9323.284729] smpboot: CPU 2 is now offline
[ 9323.289835] smpboot: CPU 1 is now offline
[ 9323.299671] ACPI: PM: Low-level resume complete
[ 9323.299726] ACPI: EC: EC started
[ 9323.299730] ACPI: PM: Restoring platform NVS memory
[ 9323.301809] Enabling non-boot CPUs ...
[ 9323.301873] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 9323.302862] CPU1 is up
[ 9323.302921] smpboot: Booting Node 0 Processor 2 APIC 0x1
[ 9323.304070] CPU2 is up
[ 9323.304127] smpboot: Booting Node 0 Processor 3 APIC 0x3
[ 9323.305095] CPU3 is up
[ 9323.310860] ACPI: PM: Waking up from system sleep state S3
[ 9323.517628] ACPI: EC: interrupt unblocked
[ 9323.545093] ACPI: EC: event unblocked
[ 9323.545265] xhci_hcd 0000:00:14.0: // Setting command ring address to 0x104954001
[ 9323.546864] xhci_hcd 0000:00:14.0: Port change event, 1-3, id 3, portsc: 0x206e1
[ 9323.547020] xhci_hcd 0000:00:14.0: resume root hub
[ 9323.547048] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.547088] xhci_hcd 0000:00:14.0: Port change event, 1-4, id 4, portsc: 0x206e1
[ 9323.547111] xhci_hcd 0000:00:14.0: resume root hub
[ 9323.547135] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.547172] xhci_hcd 0000:00:14.0: Port change event, 1-5, id 5, portsc: 0x206e1
[ 9323.547194] xhci_hcd 0000:00:14.0: resume root hub
[ 9323.547216] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.547340] xhci_hcd 0000:00:14.0: xhci_resume: starting usb1 port polling.
[ 9323.547372] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
[ 9323.547524] usb usb1: usb resume
[ 9323.548155] usb usb2: usb resume
[ 9323.548210] hub 2-0:1.0: hub_resume
[ 9323.548254] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[ 9323.548278] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[ 9323.558610] hub 1-0:1.0: hub_resume
[ 9323.558648] xhci_hcd 0000:00:14.0: Get port status 1-1 read: 0x2a0, return 0x100
[ 9323.558733] xhci_hcd 0000:00:14.0: Get port status 1-2 read: 0x2a0, return 0x100
[ 9323.558803] xhci_hcd 0000:00:14.0: Get port status 1-3 read: 0x206e1, return 0x10101
[ 9323.558862] usb usb1-port3: status 0101 change 0001
[ 9323.558895] xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x6e1
[ 9323.558964] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x206e1, return 0x10101
[ 9323.559025] usb usb1-port4: status 0101 change 0001
[ 9323.559108] xhci_hcd 0000:00:14.0: clear port4 connect change, portsc: 0x6e1
[ 9323.559223] xhci_hcd 0000:00:14.0: Get port status 1-5 read: 0x206e1, return 0x10101
[ 9323.559316] usb usb1-port5: status 0101 change 0001
[ 9323.559366] xhci_hcd 0000:00:14.0: clear port5 connect change, portsc: 0x6e1
[ 9323.559441] xhci_hcd 0000:00:14.0: Get port status 1-6 read: 0x2a0, return 0x100
[ 9323.559516] xhci_hcd 0000:00:14.0: Get port status 1-7 read: 0x2a0, return 0x100
[ 9323.559761] xhci_hcd 0000:00:14.0: Get port status 1-8 read: 0x2a0, return 0x100
[ 9323.559849] xhci_hcd 0000:00:14.0: Get port status 1-9 read: 0x2a0, return 0x100
[ 9323.559923] xhci_hcd 0000:00:14.0: Get port status 1-10 read: 0x2a0, return 0x100
[ 9323.559997] xhci_hcd 0000:00:14.0: Get port status 1-11 read: 0x2a0, return 0x100
[ 9323.560068] xhci_hcd 0000:00:14.0: Get port status 1-12 read: 0x2a0, return 0x100
[ 9323.560799] nvme nvme0: 4/0/0 default/read/poll queues
[ 9323.571119] xhci_hcd 0000:00:14.0: Get port status 2-1 read: 0x2a0, return 0x2a0
[ 9323.571187] xhci_hcd 0000:00:14.0: Get port status 2-2 read: 0x2a0, return 0x2a0
[ 9323.571233] xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2a0, return 0x2a0
[ 9323.571278] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x2a0, return 0x2a0
[ 9323.571321] xhci_hcd 0000:00:14.0: Get port status 2-5 read: 0x2a0, return 0x2a0
[ 9323.571364] xhci_hcd 0000:00:14.0: Get port status 2-6 read: 0x2a0, return 0x2a0
[ 9323.573735] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[ 9323.573753] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[ 9323.573765] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[ 9323.663115] xhci_hcd 0000:00:14.0: Get port status 1-3 read: 0x6e1, return 0x101
[ 9323.663282] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x6e1, return 0x101
[ 9323.663347] xhci_hcd 0000:00:14.0: Get port status 1-5 read: 0x6e1, return 0x101
[ 9323.667047] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb1 port polling
[ 9323.679071] usb 1-4: Waited 0ms for CONNECT
[ 9323.679092] usb 1-5: Waited 0ms for CONNECT
[ 9323.679093] usb 1-4: finish reset-resume
[ 9323.679097] usb 1-3: Waited 0ms for CONNECT
[ 9323.679100] usb 1-5: finish reset-resume
[ 9323.679108] usb 1-3: finish reset-resume
[ 9323.679128] xhci_hcd 0000:00:14.0: set port reset, actual port 1-5 status  = 0x791
[ 9323.736562] xhci_hcd 0000:00:14.0: Port change event, 1-5, id 5, portsc: 0x200e03
[ 9323.736567] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.743092] xhci_hcd 0000:00:14.0: Get port status 1-5 read: 0x200e03, return 0x100503
[ 9323.743124] xhci_hcd 0000:00:14.0: clear port5 reset change, portsc: 0xe03
[ 9323.799086] xhci_hcd 0000:00:14.0: Resetting device with slot ID 3
[ 9323.799098] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9323.799254] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9323.799305] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 9323.799446] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[ 9323.799464] xhci_hcd 0000:00:14.0: Slot already in default state
[ 9323.799982] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 9323.800239] xhci_hcd 0000:00:14.0: set port reset, actual port 1-5 status  = 0xf91
[ 9323.857529] xhci_hcd 0000:00:14.0: Port change event, 1-5, id 5, portsc: 0x200e03
[ 9323.857536] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.863085] xhci_hcd 0000:00:14.0: Get port status 1-5 read: 0x200e03, return 0x100503
[ 9323.863116] xhci_hcd 0000:00:14.0: clear port5 reset change, portsc: 0xe03
[ 9323.915043] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb1 port polling
[ 9323.919086] xhci_hcd 0000:00:14.0: Resetting device with slot ID 3
[ 9323.919097] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9323.919108] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9323.919122] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 3) in default state
[ 9323.919129] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 9323.919146] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9323.919176] xhci_hcd 0000:00:14.0: Successful setup address command
[ 9323.919188] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x00000102494000
[ 9323.919195] xhci_hcd 0000:00:14.0: Slot ID 3 dcbaa entry @00000000e8d903ce = 0x0000013f5b0000
[ 9323.919213] xhci_hcd 0000:00:14.0: Output Context DMA address = 0x13f5b0000
[ 9323.919219] xhci_hcd 0000:00:14.0: Internal device address = 3
[ 9323.937871] xhci_hcd 0000:00:14.0: set port reset, actual port 1-3 status  = 0x791
[ 9323.985658] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 00000000450912b8
[ 9323.985705] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 00000000450912b8
[ 9323.985756] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 3, new drop flags = 0x0, new add flags = 0x80
[ 9323.985808] xhci_hcd 0000:00:14.0: add ep 0x82, slot id 3, new drop flags = 0x0, new add flags = 0xa0
[ 9323.985851] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000450912b8
[ 9323.985885] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9323.986103] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 9323.987821] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 00000000450912b8
[ 9323.987987] xhci_hcd 0000:00:14.0: drop ep 0x82, slot id 3, new drop flags = 0x20, new add flags = 0x0
[ 9323.988010] xhci_hcd 0000:00:14.0: add ep 0x82, slot id 3, new drop flags = 0x20, new add flags = 0x20
[ 9323.988016] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000450912b8
[ 9323.988026] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9323.988229] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 9323.995182] xhci_hcd 0000:00:14.0: Port change event, 1-3, id 3, portsc: 0x200603
[ 9323.995189] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9323.999059] xhci_hcd 0000:00:14.0: Get port status 1-3 read: 0x200603, return 0x100103
[ 9323.999129] xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x603
[ 9324.055038] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 9324.055062] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.055225] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9324.055243] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 9324.056640] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[ 9324.056648] xhci_hcd 0000:00:14.0: Slot already in default state
[ 9324.056746] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 9324.056803] xhci_hcd 0000:00:14.0: set port reset, actual port 1-3 status  = 0x791
[ 9324.114102] xhci_hcd 0000:00:14.0: Port change event, 1-3, id 3, portsc: 0x200603
[ 9324.114110] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9324.119080] xhci_hcd 0000:00:14.0: Get port status 1-3 read: 0x200603, return 0x100103
[ 9324.119103] xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x603
[ 9324.163036] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb1 port polling
[ 9324.175072] xhci_hcd 0000:00:14.0: Resetting device with slot ID 1
[ 9324.175082] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.175090] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9324.175099] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 1) in default state
[ 9324.175103] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 9324.175115] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.175227] xhci_hcd 0000:00:14.0: Successful setup address command
[ 9324.175234] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x00000102494000
[ 9324.175239] xhci_hcd 0000:00:14.0: Slot ID 1 dcbaa entry @0000000004a5b558 = 0x0000010503b000
[ 9324.175244] xhci_hcd 0000:00:14.0: Output Context DMA address = 0x10503b000
[ 9324.175249] xhci_hcd 0000:00:14.0: Internal device address = 1
[ 9324.191500] xhci_hcd 0000:00:14.0: set port reset, actual port 1-4 status  = 0x791
[ 9324.191872] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 0000000035155d56
[ 9324.191878] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 0000000035155d56
[ 9324.191883] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 0000000035155d56
[ 9324.191887] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 0000000035155d56
[ 9324.191891] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 0000000035155d56
[ 9324.191899] xhci_hcd 0000:00:14.0: add ep 0x81, slot id 1, new drop flags = 0x0, new add flags = 0x8
[ 9324.191909] xhci_hcd 0000:00:14.0: add ep 0x82, slot id 1, new drop flags = 0x0, new add flags = 0x28
[ 9324.191917] xhci_hcd 0000:00:14.0: add ep 0x2, slot id 1, new drop flags = 0x0, new add flags = 0x38
[ 9324.191924] xhci_hcd 0000:00:14.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0xb8
[ 9324.191930] xhci_hcd 0000:00:14.0: add ep 0x3, slot id 1, new drop flags = 0x0, new add flags = 0xf8
[ 9324.191935] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 0000000035155d56
[ 9324.191941] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.192163] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 9324.192650] btusb 1-3:1.0: no reset_resume for driver btusb?
[ 9324.192655] btusb 1-3:1.1: no reset_resume for driver btusb?
[ 9324.192661] btusb 1-3:1.0: forced unbind
[ 9324.248808] xhci_hcd 0000:00:14.0: Port change event, 1-4, id 4, portsc: 0x200603
[ 9324.248815] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9324.255047] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x200603, return 0x100103
[ 9324.255085] xhci_hcd 0000:00:14.0: clear port4 reset change, portsc: 0x603
[ 9324.311038] xhci_hcd 0000:00:14.0: Resetting device with slot ID 2
[ 9324.311047] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.311205] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9324.311214] xhci_hcd 0000:00:14.0: Successful reset device command.
[ 9324.311360] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[ 9324.311367] xhci_hcd 0000:00:14.0: Slot already in default state
[ 9324.311518] xhci_hcd 0000:00:14.0: Waiting for status stage event
[ 9324.311585] xhci_hcd 0000:00:14.0: set port reset, actual port 1-4 status  = 0x791
[ 9324.368889] xhci_hcd 0000:00:14.0: Port change event, 1-4, id 4, portsc: 0x200603
[ 9324.368893] xhci_hcd 0000:00:14.0: handle_port_status: starting usb1 port polling.
[ 9324.375038] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x200603, return 0x100103
[ 9324.375067] xhci_hcd 0000:00:14.0: clear port4 reset change, portsc: 0x603
[ 9324.411035] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb1 port polling
[ 9324.431034] xhci_hcd 0000:00:14.0: Resetting device with slot ID 2
[ 9324.431042] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.431061] xhci_hcd 0000:00:14.0: Completed reset device command.
[ 9324.431071] xhci_hcd 0000:00:14.0: Can't reset device (slot ID 2) in default state
[ 9324.431077] xhci_hcd 0000:00:14.0: Not freeing device rings.
[ 9324.431096] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.431139] xhci_hcd 0000:00:14.0: Successful setup address command
[ 9324.431149] xhci_hcd 0000:00:14.0: Op regs DCBAA ptr = 0x00000102494000
[ 9324.431155] xhci_hcd 0000:00:14.0: Slot ID 2 dcbaa entry @00000000b3869263 = 0x00000105031000
[ 9324.431160] xhci_hcd 0000:00:14.0: Output Context DMA address = 0x105031000
[ 9324.431165] xhci_hcd 0000:00:14.0: Internal device address = 2
[ 9324.447487] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 00000000387dabf9
[ 9324.447493] xhci_hcd 0000:00:14.0: xhci_drop_endpoint called for udev 00000000387dabf9
[ 9324.447503] xhci_hcd 0000:00:14.0: add ep 0x81, slot id 2, new drop flags = 0x0, new add flags = 0x8
[ 9324.447511] xhci_hcd 0000:00:14.0: add ep 0x2, slot id 2, new drop flags = 0x0, new add flags = 0x18
[ 9324.447516] xhci_hcd 0000:00:14.0: xhci_check_bandwidth called for udev 00000000387dabf9
[ 9324.447524] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9324.447707] xhci_hcd 0000:00:14.0: Successful Endpoint Configure command
[ 9324.465567] OOM killer enabled.
[ 9324.465577] Restarting tasks ... 
[ 9324.465687] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 9324.465963] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-1 status  = 0xe0002a0
[ 9324.466061] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-2 status  = 0xe0002a0
[ 9324.466113] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-3 status  = 0xe0002a0
[ 9324.466172] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-4 status  = 0xe0002a0
[ 9324.466225] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-5 status  = 0xe0002a0
[ 9324.466274] xhci_hcd 0000:00:14.0: set port remote wake mask, actual port 2-6 status  = 0xe0002a0
[ 9324.467105] hub 2-0:1.0: hub_suspend
[ 9324.467171] usb usb2: bus auto-suspend, wakeup 1
[ 9324.467205] xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling
[ 9324.467454] hub 1-0:1.0: state 7 ports 12 chg 0000 evt 0010
[ 9324.467484] xhci_hcd 0000:00:14.0: Get port status 1-4 read: 0x603, return 0x103
[ 9324.469019] done.
[ 9324.469056] random: crng reseeded on system resumption
[ 9324.659957] btusb 1-3:1.0: usb_probe_interface
[ 9324.659968] btusb 1-3:1.0: usb_probe_interface - got id
[ 9324.808548] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[ 9324.826052] PM: suspend exit
[ 9324.828004] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[ 9324.828014] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[ 9325.189739] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 9325.212802] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 9325.516890] xhci_hcd 0000:00:14.0: Cancel URB 00000000321d5b09, dev 3, ep 0x81, starting at offset 0x105030270
[ 9325.516926] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9325.516963] xhci_hcd 0000:00:14.0: Stopped on Transfer TRB for slot 1 ep 2
[ 9325.516989] xhci_hcd 0000:00:14.0: Removing canceled TD starting at 0x105030270 (dma) in stream 0 URB 00000000321d5b09
[ 9325.517005] xhci_hcd 0000:00:14.0: Set TR Deq ptr 0x105030280, cycle 1

[ 9325.517015] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9325.517024] xhci_hcd 0000:00:14.0: xhci_giveback_invalidated_tds: Keep cancelled URB 00000000321d5b09 TD as cancel_status is 2
[ 9325.517039] xhci_hcd 0000:00:14.0: Successful Set TR Deq Ptr cmd, deq = @105030280
[ 9325.517048] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: Giveback cancelled URB 00000000321d5b09 TD
[ 9325.517057] xhci_hcd 0000:00:14.0: Giveback URB 00000000321d5b09, len = 0, expected = 260, status = -115
[ 9325.517070] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: All TDs cleared, ring doorbell
[ 9325.517139] xhci_hcd 0000:00:14.0: Cancel URB 0000000098a519d6, dev 3, ep 0x82, starting at offset 0x104fb8010
[ 9325.517164] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9325.517186] xhci_hcd 0000:00:14.0: Stopped on Transfer TRB for slot 1 ep 4
[ 9325.517198] xhci_hcd 0000:00:14.0: Removing canceled TD starting at 0x104fb8010 (dma) in stream 0 URB 0000000098a519d6
[ 9325.517209] xhci_hcd 0000:00:14.0: xhci_giveback_invalidated_tds: Giveback cancelled URB 0000000098a519d6 TD
[ 9325.517266] xhci_hcd 0000:00:14.0: Cancel URB 0000000042df719d, dev 3, ep 0x82, starting at offset 0x104fb8000
[ 9325.517280] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9325.517298] xhci_hcd 0000:00:14.0: Stopped on Transfer TRB for slot 1 ep 4
[ 9325.517309] xhci_hcd 0000:00:14.0: Removing canceled TD starting at 0x104fb8000 (dma) in stream 0 URB 0000000042df719d
[ 9325.517319] xhci_hcd 0000:00:14.0: Set TR Deq ptr 0x104fb8010, cycle 1

[ 9325.517327] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9325.517340] xhci_hcd 0000:00:14.0: xhci_giveback_invalidated_tds: Keep cancelled URB 0000000042df719d TD as cancel_status is 2
[ 9325.517352] xhci_hcd 0000:00:14.0: Successful Set TR Deq Ptr cmd, deq = @104fb8010
[ 9325.517361] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: Giveback cancelled URB 0000000042df719d TD
[ 9325.517369] xhci_hcd 0000:00:14.0: Giveback URB 0000000042df719d, len = 0, expected = 1028, status = -115
[ 9325.517380] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: All TDs cleared, ring doorbell
[ 9325.517891] Bluetooth: MGMT ver 1.23
[ 9326.499152] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9326.499203] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 3 ep 6
[ 9326.499225] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 3 ep 4
[ 9326.499242] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 3 ep 0
[ 9326.499539] xhci_hcd 0000:00:14.0: Set port 1-5 link state, portsc: 0xe03, write 0x10e61
[ 9326.515200] usb 1-5: usb auto-suspend, wakeup 0
[ 9326.951102] xhci_hcd 0000:00:14.0: Cancel URB 00000000039f59a1, dev 4, ep 0x81, starting at offset 0x141a28000
[ 9326.951137] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9326.951183] xhci_hcd 0000:00:14.0: Stopped on Transfer TRB for slot 2 ep 2
[ 9326.951201] xhci_hcd 0000:00:14.0: Removing canceled TD starting at 0x141a28000 (dma) in stream 0 URB 00000000039f59a1
[ 9326.951220] xhci_hcd 0000:00:14.0: Set TR Deq ptr 0x141a28010, cycle 1

[ 9326.951233] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9326.951250] xhci_hcd 0000:00:14.0: xhci_giveback_invalidated_tds: Keep cancelled URB 00000000039f59a1 TD as cancel_status is 2
[ 9326.951270] xhci_hcd 0000:00:14.0: Successful Set TR Deq Ptr cmd, deq = @141a28010
[ 9326.951284] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: Giveback cancelled URB 00000000039f59a1 TD
[ 9326.951298] xhci_hcd 0000:00:14.0: Giveback URB 00000000039f59a1, len = 0, expected = 116, status = -115
[ 9326.951319] xhci_hcd 0000:00:14.0: xhci_handle_cmd_set_deq: All TDs cleared, ring doorbell
[ 9326.951556] xhci_hcd 0000:00:14.0: // Ding dong!
[ 9326.951588] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 2 ep 3
[ 9326.951607] xhci_hcd 0000:00:14.0: Stopped on No-op or Link TRB for slot 2 ep 0
[ 9326.951652] xhci_hcd 0000:00:14.0: Set port 1-4 link state, portsc: 0x603, write 0x10661
[ 9326.967318] usb 1-4: usb auto-suspend, wakeup 1
[10055.064218] PM: suspend entry (deep)
[10055.075737] Filesystems sync: 0.011 seconds
[10055.086738] Freezing user space processes
[10055.091508] Freezing user space processes completed (elapsed 0.004 seconds)
[10055.091531] OOM killer disabled.
[10055.091543] Freezing remaining freezable tasks
[10055.093946] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[10055.094048] printk: Suspending console(s) (use no_console_suspend to debug)
[10055.814839] ACPI: EC: interrupt blocked
[10055.851082] ACPI: PM: Preparing to enter system sleep state S3
[10055.915091] ACPI: EC: event blocked
[10055.915107] ACPI: EC: EC stopped
[10055.915121] ACPI: PM: Saving platform NVS memory
[10055.918166] Disabling non-boot CPUs ...
[10055.922285] smpboot: CPU 3 is now offline
[10055.928218] smpboot: CPU 2 is now offline
[10055.934365] smpboot: CPU 1 is now offline
[10055.944218] ACPI: PM: Low-level resume complete
[10055.944273] ACPI: EC: EC started
[10055.944277] ACPI: PM: Restoring platform NVS memory
[10055.946369] Enabling non-boot CPUs ...
[10055.946434] smpboot: Booting Node 0 Processor 1 APIC 0x2
[10055.947427] CPU1 is up
[10055.947486] smpboot: Booting Node 0 Processor 2 APIC 0x1
[10055.948564] CPU2 is up
[10055.948619] smpboot: Booting Node 0 Processor 3 APIC 0x3
[10055.949590] CPU3 is up
[10055.955367] ACPI: PM: Waking up from system sleep state S3
[10056.117794] ACPI: EC: interrupt unblocked
[10056.150939] ACPI: EC: event unblocked
[10056.153825] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[10056.153845] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[10056.172985] nvme nvme0: 4/0/0 default/read/poll queues
[10056.181645] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[10056.181665] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[10056.181681] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[10056.411538] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[10056.668803] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[10056.923281] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[10057.134572] OOM killer enabled.
[10057.134579] Restarting tasks ... done.
[10057.137396] random: crng reseeded on system resumption
[10057.451049] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[10057.506516] PM: suspend exit
[10057.507334] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[10057.507344] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[10057.864578] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[10057.892831] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[10058.194265] Bluetooth: MGMT ver 1.23
[10096.684643] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[10096.684679] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[10096.689382] wlp58s0: authenticated
[10096.690763] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[10096.728055] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[10096.737497] wlp58s0: associated
[10096.803740] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[10244.658854] systemd[1]: systemd 257~rc2-3 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +IPE +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBCRYPTSETUP_PLUGINS +LIBFDISK +PCRE2 +PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD +BPF_FRAMEWORK +BTF -XKBCOMMON -UTMP +SYSVINIT +LIBARCHIVE)
[10244.659259] systemd[1]: Detected architecture x86-64.
[10245.510432] systemd[1]: bpf-restrict-fs: LSM BPF program attached
[10245.621298] systemd-ssh-generator[53310]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[10245.621313] systemd-ssh-generator[53310]: ? connect via 'ssh .host' locally
[10245.650945] systemd-sysv-generator[53312]: SysV service '/etc/init.d/xl2tpd' lacks a native systemd unit file, automatically generating a unit file for compatibility.
[10245.650961] systemd-sysv-generator[53312]: Please update package to include a native systemd unit file.
[10245.650970] systemd-sysv-generator[53312]: ! This compatibility logic is deprecated, expect removal soon. !
[10246.168155] systemd-journald[386]: Received SIGTERM from PID 1 (systemd).
[10246.168160] systemd[1]: Stopping systemd-journald.service - Journal Service...
[10246.240481] systemd[1]: systemd-journald.service: Deactivated successfully.
[10246.241386] systemd[1]: Stopped systemd-journald.service - Journal Service.
[10246.241670] systemd[1]: systemd-journald.service: Consumed 4.310s CPU time, 45.5M memory peak.
[10246.266569] systemd[1]: Starting systemd-journald.service - Journal Service...
[10246.363407] systemd-journald[53328]: Collecting audit messages is disabled.
[10246.481079] systemd[1]: Started systemd-journald.service - Journal Service.
[11096.725357] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[11098.345259] PM: suspend entry (deep)
[11098.368117] Filesystems sync: 0.022 seconds
[11098.378460] Freezing user space processes
[11098.382991] Freezing user space processes completed (elapsed 0.004 seconds)
[11098.383009] OOM killer disabled.
[11098.383018] Freezing remaining freezable tasks
[11098.385360] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[11098.385443] printk: Suspending console(s) (use no_console_suspend to debug)
[11099.017973] ACPI: EC: interrupt blocked
[11099.051519] ACPI: PM: Preparing to enter system sleep state S3
[11099.101808] ACPI: EC: event blocked
[11099.101813] ACPI: EC: EC stopped
[11099.101818] ACPI: PM: Saving platform NVS memory
[11099.103572] Disabling non-boot CPUs ...
[11099.105395] smpboot: CPU 3 is now offline
[11099.108166] smpboot: CPU 2 is now offline
[11099.110532] smpboot: CPU 1 is now offline
[11099.120384] ACPI: PM: Low-level resume complete
[11099.120449] ACPI: EC: EC started
[11099.120456] ACPI: PM: Restoring platform NVS memory
[11099.122640] Enabling non-boot CPUs ...
[11099.122704] smpboot: Booting Node 0 Processor 1 APIC 0x2
[11099.123697] CPU1 is up
[11099.123755] smpboot: Booting Node 0 Processor 2 APIC 0x1
[11099.124844] CPU2 is up
[11099.124901] smpboot: Booting Node 0 Processor 3 APIC 0x3
[11099.125899] CPU3 is up
[11099.131668] ACPI: PM: Waking up from system sleep state S3
[11099.282420] ACPI: EC: interrupt unblocked
[11099.370693] ACPI: EC: event unblocked
[11099.371509] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[11099.371530] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[11099.388883] nvme nvme0: 4/0/0 default/read/poll queues
[11099.396133] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[11099.396144] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[11099.396151] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[11099.673780] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[11099.933950] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[11100.189810] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[11100.346300] OOM killer enabled.
[11100.346309] Restarting tasks ... done.
[11100.348866] random: crng reseeded on system resumption
[11100.620068] PM: suspend exit
[11100.620555] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[11100.633468] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[11100.737247] Bluetooth: MGMT ver 1.23
[11106.295331] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[11106.295340] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[11106.299394] wlp58s0: authenticated
[11106.301425] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[11106.333723] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[11106.336350] wlp58s0: associated
[11106.405650] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[11306.936965] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[11308.608434] PM: suspend entry (deep)
[11308.623065] Filesystems sync: 0.014 seconds
[11308.627519] Freezing user space processes
[11308.631057] Freezing user space processes completed (elapsed 0.003 seconds)
[11308.631068] OOM killer disabled.
[11308.631074] Freezing remaining freezable tasks
[11308.633248] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[11308.633319] printk: Suspending console(s) (use no_console_suspend to debug)
[11309.243903] ACPI: EC: interrupt blocked
[11309.275560] ACPI: PM: Preparing to enter system sleep state S3
[11309.323905] ACPI: EC: event blocked
[11309.323911] ACPI: EC: EC stopped
[11309.323916] ACPI: PM: Saving platform NVS memory
[11309.325637] Disabling non-boot CPUs ...
[11309.327772] smpboot: CPU 3 is now offline
[11309.332020] smpboot: CPU 2 is now offline
[11309.334658] smpboot: CPU 1 is now offline
[11309.342672] ACPI: PM: Low-level resume complete
[11309.342727] ACPI: EC: EC started
[11309.342730] ACPI: PM: Restoring platform NVS memory
[11309.344829] Enabling non-boot CPUs ...
[11309.344893] smpboot: Booting Node 0 Processor 1 APIC 0x2
[11309.345927] CPU1 is up
[11309.345986] smpboot: Booting Node 0 Processor 2 APIC 0x1
[11309.347103] CPU2 is up
[11309.347161] smpboot: Booting Node 0 Processor 3 APIC 0x3
[11309.348211] CPU3 is up
[11309.353973] ACPI: PM: Waking up from system sleep state S3
[11309.558489] ACPI: EC: interrupt unblocked
[11309.619032] ACPI: EC: event unblocked
[11309.622633] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[11309.622668] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[11309.640691] nvme nvme0: 4/0/0 default/read/poll queues
[11309.650181] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[11309.650215] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[11309.650242] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[11309.875827] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[11310.136047] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[11310.391849] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[11310.537161] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[11310.537168] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[11310.539320] OOM killer enabled.
[11310.539326] Restarting tasks ... done.
[11310.551790] random: crng reseeded on system resumption
[11310.768092] PM: suspend exit
[11310.852643] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[11310.894440] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[11310.921363] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[11311.249779] Bluetooth: MGMT ver 1.23
[11316.596098] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[11316.596117] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[11316.597975] wlp58s0: authenticated
[11316.603525] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[11316.634132] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[11316.637409] wlp58s0: associated
[11316.650997] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[13980.693797] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[13982.569608] PM: suspend entry (deep)
[13982.593807] Filesystems sync: 0.024 seconds
[13982.599436] Freezing user space processes
[13982.603269] Freezing user space processes completed (elapsed 0.003 seconds)
[13982.603280] OOM killer disabled.
[13982.603287] Freezing remaining freezable tasks
[13982.605635] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[13982.605711] printk: Suspending console(s) (use no_console_suspend to debug)
[13983.225914] ACPI: EC: interrupt blocked
[13983.260259] ACPI: PM: Preparing to enter system sleep state S3
[13983.331475] ACPI: EC: event blocked
[13983.331493] ACPI: EC: EC stopped
[13983.331508] ACPI: PM: Saving platform NVS memory
[13983.335081] Disabling non-boot CPUs ...
[13983.340006] smpboot: CPU 3 is now offline
[13983.347049] smpboot: CPU 2 is now offline
[13983.356930] smpboot: CPU 1 is now offline
[13983.367014] ACPI: PM: Low-level resume complete
[13983.367078] ACPI: EC: EC started
[13983.367085] ACPI: PM: Restoring platform NVS memory
[13983.369288] Enabling non-boot CPUs ...
[13983.369351] smpboot: Booting Node 0 Processor 1 APIC 0x2
[13983.370406] CPU1 is up
[13983.370466] smpboot: Booting Node 0 Processor 2 APIC 0x1
[13983.371616] CPU2 is up
[13983.371673] smpboot: Booting Node 0 Processor 3 APIC 0x3
[13983.372715] CPU3 is up
[13983.378480] ACPI: PM: Waking up from system sleep state S3
[13983.536534] ACPI: EC: interrupt unblocked
[13983.562056] ACPI: EC: event unblocked
[13983.564053] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[13983.564075] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[13983.579808] nvme nvme0: 4/0/0 default/read/poll queues
[13983.588780] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[13983.588787] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[13983.588792] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[13983.814744] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[13983.846247] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[13984.016814] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[13984.070544] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[13984.330579] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[13984.478876] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[13984.478908] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[13984.482275] OOM killer enabled.
[13984.482282] Restarting tasks ... done.
[13984.488893] random: crng reseeded on system resumption
[13984.602231] usb 1-2: new full-speed USB device number 5 using xhci_hcd
[13984.699459] PM: suspend exit
[13984.745518] usb 1-2: New USB device found, idVendor=1395, idProduct=0025, bcdDevice= 1.00
[13984.745533] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[13984.745552] usb 1-2: Product: Sennheiser USB headset
[13984.745560] usb 1-2: Manufacturer: Sennheiser Communications 
[13984.759022] input: Sennheiser Communications  Sennheiser USB headset as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.3/0003:1395:0025.0007/input/input45
[13984.814962] hid-generic 0003:1395:0025.0007: input,hidraw2: USB HID v1.00 Device [Sennheiser Communications  Sennheiser USB headset] on usb-0000:00:14.0-2/input3
[13984.837437] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[13984.860172] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[13984.890521] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[13985.251037] Bluetooth: MGMT ver 1.23
[13985.337539] usbcore: registered new interface driver snd-usb-audio
[13990.499957] wlp58s0: authenticate with 00:81:c4:9d:bb:5f (local address=9c:b6:d0:d1:6a:b1)
[13990.500011] wlp58s0: send auth to 00:81:c4:9d:bb:5f (try 1/3)
[13990.500621] wlp58s0: authenticated
[13990.502266] wlp58s0: associate with 00:81:c4:9d:bb:5f (try 1/3)
[13990.504029] wlp58s0: RX AssocResp from 00:81:c4:9d:bb:5f (capab=0x101 status=0 aid=14)
[13990.508111] wlp58s0: associated
[13990.569083] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:9d:bb:5f
[14010.464364] wlp58s0: disconnect from AP 00:81:c4:9d:bb:5f for new auth to 00:81:c4:7c:bc:df
[14015.642457] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14015.689320] wlp58s0: authenticate with 00:81:c4:7c:bc:df (local address=9c:b6:d0:d1:6a:b1)
[14015.689371] wlp58s0: send auth to 00:81:c4:7c:bc:df (try 1/3)
[14015.690764] wlp58s0: send auth to 00:81:c4:7c:bc:df (try 2/3)
[14015.692250] wlp58s0: send auth to 00:81:c4:7c:bc:df (try 3/3)
[14015.693759] wlp58s0: authentication with 00:81:c4:7c:bc:df timed out
[14016.096044] wlp58s0: authenticate with 00:81:c4:9d:bb:5f (local address=9c:b6:d0:d1:6a:b1)
[14016.096101] wlp58s0: send auth to 00:81:c4:9d:bb:5f (try 1/3)
[14016.097438] wlp58s0: send auth to 00:81:c4:9d:bb:5f (try 2/3)
[14016.099120] wlp58s0: send auth to 00:81:c4:9d:bb:5f (try 3/3)
[14016.100436] wlp58s0: authentication with 00:81:c4:9d:bb:5f timed out
[14057.128482] wlp58s0: authenticate with bc:26:c7:1d:96:2f (local address=9c:b6:d0:d1:6a:b1)
[14057.128523] wlp58s0: send auth to bc:26:c7:1d:96:2f (try 1/3)
[14057.129621] wlp58s0: authenticated
[14057.134318] wlp58s0: associate with bc:26:c7:1d:96:2f (try 1/3)
[14057.138688] wlp58s0: RX AssocResp from bc:26:c7:1d:96:2f (capab=0x101 status=0 aid=8)
[14057.143457] wlp58s0: associated
[14057.200324] wlp58s0: Limiting TX power to 21 (21 - 0) dBm as advertised by bc:26:c7:1d:96:2f
[14085.718953] wlp58s0: disconnect from AP bc:26:c7:1d:96:2f for new auth to bc:26:c7:22:57:60
[14090.906174] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14090.977673] wlp58s0: authenticate with bc:26:c7:22:57:60 (local address=9c:b6:d0:d1:6a:b1)
[14090.977684] wlp58s0: send auth to bc:26:c7:22:57:60 (try 1/3)
[14090.979237] wlp58s0: send auth to bc:26:c7:22:57:60 (try 2/3)
[14090.981050] wlp58s0: send auth to bc:26:c7:22:57:60 (try 3/3)
[14090.982519] wlp58s0: authentication with bc:26:c7:22:57:60 timed out
[14091.738195] wlp58s0: authenticate with bc:26:c7:22:57:6f (local address=9c:b6:d0:d1:6a:b1)
[14091.738249] wlp58s0: send auth to bc:26:c7:22:57:6f (try 1/3)
[14091.742258] wlp58s0: send auth to bc:26:c7:22:57:6f (try 2/3)
[14091.744136] wlp58s0: send auth to bc:26:c7:22:57:6f (try 3/3)
[14091.745469] wlp58s0: authentication with bc:26:c7:22:57:6f timed out
[14092.487133] wlp58s0: authenticate with bc:26:c7:1d:96:2f (local address=9c:b6:d0:d1:6a:b1)
[14092.487175] wlp58s0: send auth to bc:26:c7:1d:96:2f (try 1/3)
[14092.488707] wlp58s0: send auth to bc:26:c7:1d:96:2f (try 2/3)
[14092.490348] wlp58s0: send auth to bc:26:c7:1d:96:2f (try 3/3)
[14092.491668] wlp58s0: authentication with bc:26:c7:1d:96:2f timed out
[14110.961463] wlp58s0: authenticate with 00:c8:8b:13:98:af (local address=9c:b6:d0:d1:6a:b1)
[14110.961499] wlp58s0: send auth to 00:c8:8b:13:98:af (try 1/3)
[14110.962278] wlp58s0: authenticated
[14110.970239] wlp58s0: associate with 00:c8:8b:13:98:af (try 1/3)
[14110.972227] wlp58s0: RX AssocResp from 00:c8:8b:13:98:af (capab=0x101 status=0 aid=79)
[14110.982568] wlp58s0: associated
[14111.052861] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:c8:8b:13:98:af
[14150.470843] wlp58s0: disconnect from AP 00:c8:8b:13:98:af for new auth to 00:2a:10:22:ed:f0
[14155.673892] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14155.774667] wlp58s0: authenticate with 00:2a:10:22:ed:f0 (local address=9c:b6:d0:d1:6a:b1)
[14155.774732] wlp58s0: send auth to 00:2a:10:22:ed:f0 (try 1/3)
[14155.778597] wlp58s0: send auth to 00:2a:10:22:ed:f0 (try 2/3)
[14155.781175] wlp58s0: send auth to 00:2a:10:22:ed:f0 (try 3/3)
[14155.783042] wlp58s0: authentication with 00:2a:10:22:ed:f0 timed out
[14156.529117] wlp58s0: authenticate with 00:2a:10:22:ed:ff (local address=9c:b6:d0:d1:6a:b1)
[14156.529150] wlp58s0: send auth to 00:2a:10:22:ed:ff (try 1/3)
[14156.530500] wlp58s0: send auth to 00:2a:10:22:ed:ff (try 2/3)
[14156.533181] wlp58s0: send auth to 00:2a:10:22:ed:ff (try 3/3)
[14156.534916] wlp58s0: authentication with 00:2a:10:22:ed:ff timed out
[14157.525467] wlp58s0: authenticate with 00:81:c4:21:6d:20 (local address=9c:b6:d0:d1:6a:b1)
[14157.525504] wlp58s0: send auth to 00:81:c4:21:6d:20 (try 1/3)
[14157.527250] wlp58s0: send auth to 00:81:c4:21:6d:20 (try 2/3)
[14157.529043] wlp58s0: send auth to 00:81:c4:21:6d:20 (try 3/3)
[14157.536968] wlp58s0: authentication with 00:81:c4:21:6d:20 timed out
[14158.779682] wlp58s0: authenticate with 00:c8:8b:13:98:af (local address=9c:b6:d0:d1:6a:b1)
[14158.779718] wlp58s0: send auth to 00:c8:8b:13:98:af (try 1/3)
[14158.780950] wlp58s0: send auth to 00:c8:8b:13:98:af (try 2/3)
[14158.782489] wlp58s0: send auth to 00:c8:8b:13:98:af (try 3/3)
[14158.783909] wlp58s0: authentication with 00:c8:8b:13:98:af timed out
[14175.921638] wlp58s0: authenticate with 00:81:c4:f6:16:af (local address=9c:b6:d0:d1:6a:b1)
[14175.921648] wlp58s0: send auth to 00:81:c4:f6:16:af (try 1/3)
[14175.922270] wlp58s0: authenticated
[14175.925670] wlp58s0: associate with 00:81:c4:f6:16:af (try 1/3)
[14175.927387] wlp58s0: RX AssocResp from 00:81:c4:f6:16:af (capab=0x101 status=0 aid=133)
[14175.930114] wlp58s0: associated
[14175.987889] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:f6:16:af
[14213.006903] wlp58s0: deauthenticating from 00:81:c4:f6:16:af by local choice (Reason: 3=DEAUTH_LEAVING)
[14280.776598] wlp58s0: authenticate with 00:81:c4:90:e6:0f (local address=9c:b6:d0:d1:6a:b1)
[14280.776649] wlp58s0: send auth to 00:81:c4:90:e6:0f (try 1/3)
[14280.777835] wlp58s0: authenticated
[14280.780841] wlp58s0: associate with 00:81:c4:90:e6:0f (try 1/3)
[14280.783457] wlp58s0: RX AssocResp from 00:81:c4:90:e6:0f (capab=0x101 status=0 aid=23)
[14280.793583] wlp58s0: associated
[14280.862267] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:90:e6:0f
[14293.269412] wlp58s0: deauthenticating from 00:81:c4:90:e6:0f by local choice (Reason: 3=DEAUTH_LEAVING)
[14359.168793] wlp58s0: authenticate with b8:11:4b:ba:15:ef (local address=9c:b6:d0:d1:6a:b1)
[14359.168803] wlp58s0: send auth to b8:11:4b:ba:15:ef (try 1/3)
[14359.169975] wlp58s0: authenticated
[14359.172018] wlp58s0: associate with b8:11:4b:ba:15:ef (try 1/3)
[14359.180564] wlp58s0: RX AssocResp from b8:11:4b:ba:15:ef (capab=0x101 status=0 aid=16)
[14359.184847] wlp58s0: associated
[14359.274412] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by b8:11:4b:ba:15:ef
[14378.948910] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 1 comp_code 1
[14378.948943] xhci_hcd 0000:00:14.0: Looking for event-dma 000000026402fff0 trb-start 00000001a9383000 trb-end 00000001a9383000 seg-start 00000001a9383000 seg-end 00000001a9383ff0
[14378.949260] usb 1-2: USB disconnect, device number 5
[14378.950837] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 1 comp_code 1
[14378.950896] xhci_hcd 0000:00:14.0: Looking for event-dma 00000001a9383010 trb-start 00000001a9383020 trb-end 00000001a9383020 seg-start 00000001a9383000 seg-end 00000001a9383ff0
[14378.952289] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 1 comp_code 1
[14378.952345] xhci_hcd 0000:00:14.0: Looking for event-dma 00000001a9383020 trb-start 00000001a9383030 trb-end 00000001a9383030 seg-start 00000001a9383000 seg-end 00000001a9383ff0
[14379.279956] usb 1-2: new full-speed USB device number 6 using xhci_hcd
[14379.426282] usb 1-2: New USB device found, idVendor=1395, idProduct=0025, bcdDevice= 1.00
[14379.426321] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[14379.426343] usb 1-2: Product: Sennheiser USB headset
[14379.426363] usb 1-2: Manufacturer: Sennheiser Communications 
[14379.489845] input: Sennheiser Communications  Sennheiser USB headset as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.3/0003:1395:0025.0008/input/input46
[14379.550975] hid-generic 0003:1395:0025.0008: input,hidraw2: USB HID v1.00 Device [Sennheiser Communications  Sennheiser USB headset] on usb-0000:00:14.0-2/input3
[14381.896914] wlp58s0: disconnect from AP b8:11:4b:ba:15:ef for new auth to 1c:d1:e0:3b:d0:6f
[14387.096280] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14387.153981] wlp58s0: authenticate with 1c:d1:e0:3b:d0:6f (local address=9c:b6:d0:d1:6a:b1)
[14387.154035] wlp58s0: send auth to 1c:d1:e0:3b:d0:6f (try 1/3)
[14387.155937] wlp58s0: send auth to 1c:d1:e0:3b:d0:6f (try 2/3)
[14387.157325] wlp58s0: send auth to 1c:d1:e0:3b:d0:6f (try 3/3)
[14387.158686] wlp58s0: authentication with 1c:d1:e0:3b:d0:6f timed out
[14387.902906] wlp58s0: authenticate with 1c:d1:e0:3c:be:2f (local address=9c:b6:d0:d1:6a:b1)
[14387.902956] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 1/3)
[14387.905311] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 2/3)
[14387.906751] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 3/3)
[14387.908143] wlp58s0: authentication with 1c:d1:e0:3c:be:2f timed out
[14388.704429] wlp58s0: authenticate with b8:11:4b:ba:15:ef (local address=9c:b6:d0:d1:6a:b1)
[14388.704485] wlp58s0: send auth to b8:11:4b:ba:15:ef (try 1/3)
[14388.706086] wlp58s0: send auth to b8:11:4b:ba:15:ef (try 2/3)
[14388.709517] wlp58s0: send auth to b8:11:4b:ba:15:ef (try 3/3)
[14388.711019] wlp58s0: authentication with b8:11:4b:ba:15:ef timed out
[14464.356799] wlp58s0: authenticate with 78:bc:1a:02:dc:4f (local address=9c:b6:d0:d1:6a:b1)
[14464.356816] wlp58s0: send auth to 78:bc:1a:02:dc:4f (try 1/3)
[14464.357798] wlp58s0: authenticated
[14464.359133] wlp58s0: associate with 78:bc:1a:02:dc:4f (try 1/3)
[14464.362257] wlp58s0: RX AssocResp from 78:bc:1a:02:dc:4f (capab=0x101 status=0 aid=162)
[14464.366705] wlp58s0: associated
[14464.401044] wlp58s0: Limiting TX power to 21 (21 - 0) dBm as advertised by 78:bc:1a:02:dc:4f
[14490.518967] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14490.556477] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[14542.341520] wlp58s0: authenticate with 00:81:c4:6e:6e:2f (local address=9c:b6:d0:d1:6a:b1)
[14542.341565] wlp58s0: send auth to 00:81:c4:6e:6e:2f (try 1/3)
[14542.342855] wlp58s0: authenticated
[14542.346354] wlp58s0: associate with 00:81:c4:6e:6e:2f (try 1/3)
[14542.348327] wlp58s0: RX AssocResp from 00:81:c4:6e:6e:2f (capab=0x101 status=0 aid=38)
[14542.357012] wlp58s0: associated
[14542.370118] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:6e:6e:2f
[14586.005925] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[14586.019473] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[14586.560274] wlp58s0: authenticate with 00:81:c4:6e:6e:20 (local address=9c:b6:d0:d1:6a:b1)
[14586.560331] wlp58s0: send auth to 00:81:c4:6e:6e:20 (try 1/3)
[14586.562738] wlp58s0: send auth to 00:81:c4:6e:6e:20 (try 2/3)
[14586.564753] wlp58s0: send auth to 00:81:c4:6e:6e:20 (try 3/3)
[14586.566599] wlp58s0: authentication with 00:81:c4:6e:6e:20 timed out
[14592.018506] wlp58s0: authenticate with 00:81:c4:6e:6e:2f (local address=9c:b6:d0:d1:6a:b1)
[14592.018559] wlp58s0: send auth to 00:81:c4:6e:6e:2f (try 1/3)
[14592.019936] wlp58s0: send auth to 00:81:c4:6e:6e:2f (try 2/3)
[14592.021278] wlp58s0: send auth to 00:81:c4:6e:6e:2f (try 3/3)
[14592.022677] wlp58s0: authentication with 00:81:c4:6e:6e:2f timed out
[14624.520457] wlp58s0: authenticate with b4:de:31:52:93:ef (local address=9c:b6:d0:d1:6a:b1)
[14624.520514] wlp58s0: send auth to b4:de:31:52:93:ef (try 1/3)
[14624.523011] wlp58s0: authenticated
[14624.529503] wlp58s0: associate with b4:de:31:52:93:ef (try 1/3)
[14624.534144] wlp58s0: RX AssocResp from b4:de:31:52:93:ef (capab=0x101 status=0 aid=100)
[14624.542069] wlp58s0: associated
[14624.595613] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by b4:de:31:52:93:ef
[14656.045876] wlp58s0: deauthenticating from b4:de:31:52:93:ef by local choice (Reason: 3=DEAUTH_LEAVING)
[14675.201408] usb 1-2: USB disconnect, device number 6
[14676.278742] PM: suspend entry (deep)
[14676.309196] Filesystems sync: 0.030 seconds
[14676.321526] Freezing user space processes
[14676.329928] Freezing user space processes completed (elapsed 0.008 seconds)
[14676.329969] OOM killer disabled.
[14676.329989] Freezing remaining freezable tasks
[14676.334042] Freezing remaining freezable tasks completed (elapsed 0.004 seconds)
[14676.334195] printk: Suspending console(s) (use no_console_suspend to debug)
[14676.961844] ACPI: EC: interrupt blocked
[14676.997419] ACPI: PM: Preparing to enter system sleep state S3
[14677.061341] ACPI: EC: event blocked
[14677.061357] ACPI: EC: EC stopped
[14677.061371] ACPI: PM: Saving platform NVS memory
[14677.064471] Disabling non-boot CPUs ...
[14677.068110] smpboot: CPU 3 is now offline
[14677.076561] smpboot: CPU 2 is now offline
[14677.081717] smpboot: CPU 1 is now offline
[14677.091985] ACPI: PM: Low-level resume complete
[14677.092050] ACPI: EC: EC started
[14677.092056] ACPI: PM: Restoring platform NVS memory
[14677.094251] Enabling non-boot CPUs ...
[14677.094316] smpboot: Booting Node 0 Processor 1 APIC 0x2
[14677.095369] CPU1 is up
[14677.095429] smpboot: Booting Node 0 Processor 2 APIC 0x1
[14677.096906] CPU2 is up
[14677.096963] smpboot: Booting Node 0 Processor 3 APIC 0x3
[14677.098008] CPU3 is up
[14677.103724] ACPI: PM: Waking up from system sleep state S3
[14677.304033] ACPI: EC: interrupt unblocked
[14677.326213] ACPI: EC: event unblocked
[14677.328934] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[14677.328956] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[14677.341117] nvme nvme0: 4/0/0 default/read/poll queues
[14677.354203] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[14677.354213] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[14677.354220] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[14677.580656] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[14677.595867] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[14677.836322] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[14678.096358] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[14678.395153] OOM killer enabled.
[14678.395186] Restarting tasks ... done.
[14678.407709] random: crng reseeded on system resumption
[14678.717440] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[14678.809801] PM: suspend exit
[14678.812163] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[14678.812175] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[14679.170374] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[14679.193349] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[14679.497936] Bluetooth: MGMT ver 1.23
[14712.816419] wlp58s0: authenticate with 00:81:c4:93:c7:3f (local address=9c:b6:d0:d1:6a:b1)
[14712.816455] wlp58s0: send auth to 00:81:c4:93:c7:3f (try 1/3)
[14712.817224] wlp58s0: authenticated
[14712.819386] wlp58s0: associate with 00:81:c4:93:c7:3f (try 1/3)
[14712.821434] wlp58s0: RX AssocResp from 00:81:c4:93:c7:3f (capab=0x101 status=0 aid=1)
[14712.831650] wlp58s0: associated
[14712.874044] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:93:c7:3f
[15083.449116] wlp58s0: disconnect from AP 00:81:c4:93:c7:3f for new auth to 00:81:c4:91:21:2f
[15083.546339] wlp58s0: authenticate with 00:81:c4:91:21:2f (local address=9c:b6:d0:d1:6a:b1)
[15083.546383] wlp58s0: send auth to 00:81:c4:91:21:2f (try 1/3)
[15083.547142] wlp58s0: authenticated
[15083.555803] wlp58s0: associate with 00:81:c4:91:21:2f (try 1/3)
[15083.558783] wlp58s0: RX ReassocResp from 00:81:c4:91:21:2f (capab=0x101 status=0 aid=6)
[15083.573371] wlp58s0: associated
[15083.584473] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:91:21:2f
[15101.155702] wlp58s0: disconnect from AP 00:81:c4:91:21:2f for new auth to 00:81:c4:93:c7:3f
[15106.455394] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[15106.496505] wlp58s0: authenticate with 00:81:c4:93:c7:3f (local address=9c:b6:d0:d1:6a:b1)
[15106.496562] wlp58s0: send auth to 00:81:c4:93:c7:3f (try 1/3)
[15106.499428] wlp58s0: send auth to 00:81:c4:93:c7:3f (try 2/3)
[15106.500828] wlp58s0: send auth to 00:81:c4:93:c7:3f (try 3/3)
[15106.503027] wlp58s0: authentication with 00:81:c4:93:c7:3f timed out
[15107.129158] wlp58s0: authenticate with 00:81:c4:f6:25:20 (local address=9c:b6:d0:d1:6a:b1)
[15107.129194] wlp58s0: send auth to 00:81:c4:f6:25:20 (try 1/3)
[15107.132647] wlp58s0: send auth to 00:81:c4:f6:25:20 (try 2/3)
[15107.135111] wlp58s0: send auth to 00:81:c4:f6:25:20 (try 3/3)
[15107.137087] wlp58s0: authentication with 00:81:c4:f6:25:20 timed out
[15108.110489] wlp58s0: authenticate with 00:81:c4:91:21:20 (local address=9c:b6:d0:d1:6a:b1)
[15108.110527] wlp58s0: send auth to 00:81:c4:91:21:20 (try 1/3)
[15108.112197] wlp58s0: send auth to 00:81:c4:91:21:20 (try 2/3)
[15108.113838] wlp58s0: send auth to 00:81:c4:91:21:20 (try 3/3)
[15108.116267] wlp58s0: authentication with 00:81:c4:91:21:20 timed out
[15109.500567] wlp58s0: authenticate with 00:81:c4:f6:25:2f (local address=9c:b6:d0:d1:6a:b1)
[15109.500595] wlp58s0: send auth to 00:81:c4:f6:25:2f (try 1/3)
[15109.501840] wlp58s0: send auth to 00:81:c4:f6:25:2f (try 2/3)
[15109.503140] wlp58s0: send auth to 00:81:c4:f6:25:2f (try 3/3)
[15109.504522] wlp58s0: authentication with 00:81:c4:f6:25:2f timed out
[15127.045281] wlp58s0: authenticate with 00:81:c4:f6:19:9f (local address=9c:b6:d0:d1:6a:b1)
[15127.045317] wlp58s0: send auth to 00:81:c4:f6:19:9f (try 1/3)
[15127.046044] wlp58s0: authenticated
[15127.047664] wlp58s0: associate with 00:81:c4:f6:19:9f (try 1/3)
[15127.049681] wlp58s0: RX AssocResp from 00:81:c4:f6:19:9f (capab=0x101 status=0 aid=31)
[15127.057046] wlp58s0: associated
[15127.066058] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:f6:19:9f
[15155.159775] wlp58s0: deauthenticating from 00:81:c4:f6:19:9f by local choice (Reason: 3=DEAUTH_LEAVING)
[15222.044415] wlp58s0: authenticate with 00:81:c4:7c:cf:3f (local address=9c:b6:d0:d1:6a:b1)
[15222.044456] wlp58s0: send auth to 00:81:c4:7c:cf:3f (try 1/3)
[15222.045193] wlp58s0: authenticated
[15222.046216] wlp58s0: associate with 00:81:c4:7c:cf:3f (try 1/3)
[15222.048296] wlp58s0: RX AssocResp from 00:81:c4:7c:cf:3f (capab=0x101 status=0 aid=5)
[15222.051788] wlp58s0: associated
[15222.117764] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:7c:cf:3f
[15261.077768] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[15261.085920] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[15261.611646] wlp58s0: authenticate with 00:81:c4:9d:bb:3f (local address=9c:b6:d0:d1:6a:b1)
[15261.611675] wlp58s0: send auth to 00:81:c4:9d:bb:3f (try 1/3)
[15261.612945] wlp58s0: send auth to 00:81:c4:9d:bb:3f (try 2/3)
[15261.615682] wlp58s0: send auth to 00:81:c4:9d:bb:3f (try 3/3)
[15261.616879] wlp58s0: authentication with 00:81:c4:9d:bb:3f timed out
[15262.351598] wlp58s0: authenticate with 00:81:c4:f8:8c:3f (local address=9c:b6:d0:d1:6a:b1)
[15262.351618] wlp58s0: send auth to 00:81:c4:f8:8c:3f (try 1/3)
[15262.353329] wlp58s0: send auth to 00:81:c4:f8:8c:3f (try 2/3)
[15262.354471] wlp58s0: send auth to 00:81:c4:f8:8c:3f (try 3/3)
[15262.355568] wlp58s0: authentication with 00:81:c4:f8:8c:3f timed out
[15268.283687] wlp58s0: authenticate with 00:81:c4:7c:cf:3f (local address=9c:b6:d0:d1:6a:b1)
[15268.283698] wlp58s0: send auth to 00:81:c4:7c:cf:3f (try 1/3)
[15268.284877] wlp58s0: send auth to 00:81:c4:7c:cf:3f (try 2/3)
[15268.286249] wlp58s0: send auth to 00:81:c4:7c:cf:3f (try 3/3)
[15268.287479] wlp58s0: authentication with 00:81:c4:7c:cf:3f timed out
[15298.459001] wlp58s0: authenticate with 00:f2:8b:87:5f:ff (local address=9c:b6:d0:d1:6a:b1)
[15298.459032] wlp58s0: send auth to 00:f2:8b:87:5f:ff (try 1/3)
[15298.459728] wlp58s0: authenticated
[15298.465510] wlp58s0: associate with 00:f2:8b:87:5f:ff (try 1/3)
[15298.467591] wlp58s0: RX AssocResp from 00:f2:8b:87:5f:ff (capab=0x101 status=0 aid=26)
[15298.476618] wlp58s0: associated
[15298.491065] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:f2:8b:87:5f:ff
[15363.220925] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[15363.242275] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[15364.108495] wlp58s0: authenticate with 00:f2:8b:87:63:cf (local address=9c:b6:d0:d1:6a:b1)
[15364.108544] wlp58s0: send auth to 00:f2:8b:87:63:cf (try 1/3)
[15364.112772] wlp58s0: authenticated
[15364.120863] wlp58s0: associate with 00:f2:8b:87:63:cf (try 1/3)
[15364.123505] wlp58s0: RX AssocResp from 00:f2:8b:87:63:cf (capab=0x101 status=0 aid=78)
[15364.128065] wlp58s0: associated
[15364.320572] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:f2:8b:87:63:cf
[15376.788695] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[15376.802031] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[15377.119190] wlp58s0: authenticate with 00:f2:8b:87:5f:ff (local address=9c:b6:d0:d1:6a:b1)
[15377.119263] wlp58s0: send auth to 00:f2:8b:87:5f:ff (try 1/3)
[15377.120678] wlp58s0: send auth to 00:f2:8b:87:5f:ff (try 2/3)
[15377.122161] wlp58s0: send auth to 00:f2:8b:87:5f:ff (try 3/3)
[15377.123641] wlp58s0: authentication with 00:f2:8b:87:5f:ff timed out
[15382.543643] wlp58s0: authenticate with 00:f2:8b:87:63:cf (local address=9c:b6:d0:d1:6a:b1)
[15382.543679] wlp58s0: send auth to 00:f2:8b:87:63:cf (try 1/3)
[15382.545041] wlp58s0: send auth to 00:f2:8b:87:63:cf (try 2/3)
[15382.546639] wlp58s0: send auth to 00:f2:8b:87:63:cf (try 3/3)
[15382.547920] wlp58s0: authentication with 00:f2:8b:87:63:cf timed out
[15420.364132] wlp58s0: authenticate with 1c:d1:e0:3c:be:2f (local address=9c:b6:d0:d1:6a:b1)
[15420.364146] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 1/3)
[15420.365367] wlp58s0: authenticated
[15420.368143] wlp58s0: associate with 1c:d1:e0:3c:be:2f (try 1/3)
[15420.371808] wlp58s0: RX AssocResp from 1c:d1:e0:3c:be:2f (capab=0x101 status=0 aid=3)
[15420.376437] wlp58s0: associated
[15420.417076] wlp58s0: Limiting TX power to 30 (30 - 0) dBm as advertised by 1c:d1:e0:3c:be:2f
[15485.843771] ath10k_pci 0000:3a:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
[15485.852182] wlp58s0: Connection to AP 00:00:00:00:00:00 lost
[15486.533119] wlp58s0: authenticate with b8:11:4b:ba:d2:4f (local address=9c:b6:d0:d1:6a:b1)
[15486.533147] wlp58s0: send auth to b8:11:4b:ba:d2:4f (try 1/3)
[15486.534420] wlp58s0: send auth to b8:11:4b:ba:d2:4f (try 2/3)
[15486.535927] wlp58s0: send auth to b8:11:4b:ba:d2:4f (try 3/3)
[15486.537205] wlp58s0: authentication with b8:11:4b:ba:d2:4f timed out
[15491.952716] wlp58s0: authenticate with 1c:d1:e0:3c:be:2f (local address=9c:b6:d0:d1:6a:b1)
[15491.952730] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 1/3)
[15491.953824] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 2/3)
[15491.955632] wlp58s0: send auth to 1c:d1:e0:3c:be:2f (try 3/3)
[15491.957043] wlp58s0: authentication with 1c:d1:e0:3c:be:2f timed out
[15510.785891] wlp58s0: authenticate with 00:81:c4:90:e6:0f (local address=9c:b6:d0:d1:6a:b1)
[15510.785919] wlp58s0: send auth to 00:81:c4:90:e6:0f (try 1/3)
[15510.786685] wlp58s0: authenticated
[15510.791443] wlp58s0: associate with 00:81:c4:90:e6:0f (try 1/3)
[15510.793453] wlp58s0: RX AssocResp from 00:81:c4:90:e6:0f (capab=0x101 status=0 aid=2)
[15510.797208] wlp58s0: associated
[15510.813406] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:90:e6:0f
[15522.961217] wlp58s0: disconnect from AP 00:81:c4:90:e6:0f for new auth to 00:81:c4:91:06:cf
[15523.070831] wlp58s0: authenticate with 00:81:c4:91:06:cf (local address=9c:b6:d0:d1:6a:b1)
[15523.070859] wlp58s0: send auth to 00:81:c4:91:06:cf (try 1/3)
[15523.071839] wlp58s0: authenticated
[15523.080655] wlp58s0: associate with 00:81:c4:91:06:cf (try 1/3)
[15523.082594] wlp58s0: RX ReassocResp from 00:81:c4:91:06:cf (capab=0x101 status=0 aid=1)
[15523.089610] wlp58s0: associated
[15523.183501] wlp58s0: Limiting TX power to 17 dBm as advertised by 00:81:c4:91:06:cf
[15528.810488] wlp58s0: deauthenticating from 00:81:c4:91:06:cf by local choice (Reason: 3=DEAUTH_LEAVING)
[15929.466350] PM: suspend entry (deep)
[15929.486766] Filesystems sync: 0.020 seconds
[15929.492205] Freezing user space processes
[15929.496045] Freezing user space processes completed (elapsed 0.003 seconds)
[15929.496056] OOM killer disabled.
[15929.496062] Freezing remaining freezable tasks
[15929.498429] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[15929.498507] printk: Suspending console(s) (use no_console_suspend to debug)
[15930.131997] ACPI: EC: interrupt blocked
[15930.167648] ACPI: PM: Preparing to enter system sleep state S3
[15930.239953] ACPI: EC: event blocked
[15930.239971] ACPI: EC: EC stopped
[15930.239986] ACPI: PM: Saving platform NVS memory
[15930.243451] Disabling non-boot CPUs ...
[15930.247251] smpboot: CPU 3 is now offline
[15930.264370] smpboot: CPU 2 is now offline
[15930.274240] smpboot: CPU 1 is now offline
[15930.285660] ACPI: PM: Low-level resume complete
[15930.285737] ACPI: EC: EC started
[15930.285741] ACPI: PM: Restoring platform NVS memory
[15930.288497] Enabling non-boot CPUs ...
[15930.288596] smpboot: Booting Node 0 Processor 1 APIC 0x2
[15930.290004] CPU1 is up
[15930.290085] smpboot: Booting Node 0 Processor 2 APIC 0x1
[15930.291717] CPU2 is up
[15930.291796] smpboot: Booting Node 0 Processor 3 APIC 0x3
[15930.293229] CPU3 is up
[15930.301012] ACPI: PM: Waking up from system sleep state S3
[15931.018790] ACPI: EC: interrupt unblocked
[15931.054204] ACPI: EC: event unblocked
[15931.058002] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[15931.058069] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[15931.074508] nvme nvme0: 4/0/0 default/read/poll queues
[15931.085374] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[15931.085410] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[15931.085439] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[15931.310991] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[15931.567256] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[15931.827053] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[15931.973333] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[15931.976262] OOM killer enabled.
[15931.976269] Restarting tasks ... done.
[15931.987147] random: crng reseeded on system resumption
[15932.578388] PM: suspend exit
[15932.580074] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[15932.580103] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[15932.940705] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[15932.964810] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[15933.281623] Bluetooth: MGMT ver 1.23
[16004.967229] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[16004.967276] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[16004.970588] wlp58s0: authenticated
[16004.978131] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[16005.006361] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=3)
[16005.016204] wlp58s0: associated
[16005.082715] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[16210.532339] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[16213.102240] PM: suspend entry (deep)
[16213.143791] Filesystems sync: 0.041 seconds
[16213.172338] Freezing user space processes
[16213.185262] Freezing user space processes completed (elapsed 0.012 seconds)
[16213.185338] OOM killer disabled.
[16213.185376] Freezing remaining freezable tasks
[16213.191151] Freezing remaining freezable tasks completed (elapsed 0.005 seconds)
[16213.191407] printk: Suspending console(s) (use no_console_suspend to debug)
[16213.817250] ACPI: EC: interrupt blocked
[16213.860826] ACPI: PM: Preparing to enter system sleep state S3
[16213.969325] ACPI: EC: event blocked
[16213.969358] ACPI: EC: EC stopped
[16213.969373] ACPI: PM: Saving platform NVS memory
[16213.974551] Disabling non-boot CPUs ...
[16213.980186] smpboot: CPU 3 is now offline
[16213.989795] smpboot: CPU 2 is now offline
[16213.999453] smpboot: CPU 1 is now offline
[16214.023641] ACPI: PM: Low-level resume complete
[16214.023696] ACPI: EC: EC started
[16214.023700] ACPI: PM: Restoring platform NVS memory
[16214.025787] Enabling non-boot CPUs ...
[16214.025852] smpboot: Booting Node 0 Processor 1 APIC 0x2
[16214.026934] CPU1 is up
[16214.026992] smpboot: Booting Node 0 Processor 2 APIC 0x1
[16214.028171] CPU2 is up
[16214.028227] smpboot: Booting Node 0 Processor 3 APIC 0x3
[16214.029303] CPU3 is up
[16214.035016] ACPI: PM: Waking up from system sleep state S3
[16214.223847] ACPI: EC: interrupt unblocked
[16214.249835] ACPI: EC: event unblocked
[16214.251193] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[16214.251208] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[16214.261876] nvme nvme0: 4/0/0 default/read/poll queues
[16214.275572] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[16214.275583] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[16214.275592] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[16214.501499] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[16214.525021] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
[16214.693006] atkbd serio0: Spurious ACK on isa0060/serio0. Some program might be trying to access hardware directly.
[16214.757374] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[16215.013297] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[16215.218388] OOM killer enabled.
[16215.218396] Restarting tasks ... done.
[16215.222194] random: crng reseeded on system resumption
[16215.531935] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[16215.594396] PM: suspend exit
[16215.595712] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[16215.595722] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[16215.951671] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[16215.974734] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[16216.239806] Bluetooth: MGMT ver 1.23
[16221.065929] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[16221.065950] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[16221.067803] wlp58s0: authenticated
[16221.069124] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[16221.101546] wlp58s0: RX AssocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[16221.105837] wlp58s0: associated
[16221.169162] wlp58s0: Limiting TX power to 23 (23 - 0) dBm as advertised by 88:71:b1:81:93:1b
[16713.146805] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[16714.923829] PM: suspend entry (deep)
[16714.946062] Filesystems sync: 0.022 seconds
[16714.951825] Freezing user space processes
[16714.955476] Freezing user space processes completed (elapsed 0.003 seconds)
[16714.955488] OOM killer disabled.
[16714.955494] Freezing remaining freezable tasks
[16714.957647] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[16714.957724] printk: Suspending console(s) (use no_console_suspend to debug)
[16715.561662] ACPI: EC: interrupt blocked
[16715.596596] ACPI: PM: Preparing to enter system sleep state S3
[16715.671877] ACPI: EC: event blocked
[16715.671895] ACPI: EC: EC stopped
[16715.671910] ACPI: PM: Saving platform NVS memory
[16715.675352] Disabling non-boot CPUs ...
[16715.679131] smpboot: CPU 3 is now offline
[16715.686215] smpboot: CPU 2 is now offline
[16715.693472] smpboot: CPU 1 is now offline
[16715.704589] ACPI: PM: Low-level resume complete
[16715.704644] ACPI: EC: EC started
[16715.704648] ACPI: PM: Restoring platform NVS memory
[16715.706748] Enabling non-boot CPUs ...
[16715.706816] smpboot: Booting Node 0 Processor 1 APIC 0x2
[16715.707868] CPU1 is up
[16715.707926] smpboot: Booting Node 0 Processor 2 APIC 0x1
[16715.709172] CPU2 is up
[16715.709228] smpboot: Booting Node 0 Processor 3 APIC 0x3
[16715.710273] CPU3 is up
[16715.716037] ACPI: PM: Waking up from system sleep state S3
[16715.913957] ACPI: EC: interrupt unblocked
[16715.975758] ACPI: EC: event unblocked
[16715.976922] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[16715.976950] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[16715.989387] nvme nvme0: 4/0/0 default/read/poll queues
[16716.003163] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[16716.003185] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[16716.003199] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[16716.237318] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[16716.493028] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[16716.752851] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[16716.961975] OOM killer enabled.
[16716.961985] Restarting tasks ... done.
[16716.968566] random: crng reseeded on system resumption
[16717.198424] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[16717.282763] PM: suspend exit
[16717.284077] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[16717.284087] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[16717.639305] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[16717.662977] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[16718.015669] Bluetooth: MGMT ver 1.23
[16804.971329] wlp58s0: authenticate with 88:71:b1:81:93:1a (local address=9c:b6:d0:d1:6a:b1)
[16804.971342] wlp58s0: send auth to 88:71:b1:81:93:1a (try 1/3)
[16804.973400] wlp58s0: authenticated
[16804.975691] wlp58s0: associate with 88:71:b1:81:93:1a (try 1/3)
[16805.002226] wlp58s0: RX AssocResp from 88:71:b1:81:93:1a (capab=0x1431 status=0 aid=1)
[16805.002244] wlp58s0: AP 88:71:b1:81:93:1a changed bandwidth, new used config is 2437.000 MHz, width 1 (2437.000/0 MHz)
[16805.002289] ------------[ cut here ]------------
[16805.002296] WARNING: CPU: 3 PID: 65835 at drivers/net/wireless/ath/ath10k/mac.c:8750 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.002321] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi cpuid sctp sd_mod usb_storage scsi_mod scsi_common r8153_ecm cdc_ether usbnet r8152 mii rfcomm cmac algif_hash algif_skcipher af_alg ctr ccm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppox ppp_generic slhc xfrm_interface xfrm6_tunnel tunnel6 xfrm_user xfrm_algo uvcvideo snd_hda_codec_hdmi btusb btrtl videobuf2_vmalloc btintel videobuf2_memops uvc btbcm videobuf2_v4l2 videodev videobuf2_common bluetooth usbhid mc ecdh_generic ecc snd_ctl_led snd_hda_codec_realtek snd_hda_codec_generic snd_hda_scodec_component joydev snd_sof_pci_intel_skl snd_sof_intel_hda_generic snd_soc_acpi_intel_match snd_soc_acpi binfmt_misc snd_soc_acpi_intel_sdca_quirks snd_sof_pci snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence soundwire_bus snd_soc_sdca snd_sof_intel_hda_common snd_soc_hdac_hda snd_sof_intel_hda_mlink snd_sof_intel_hda snd_sof x86_pkg_temp_thermal
[16805.002674]  intel_powerclamp snd_sof_utils coretemp snd_soc_avs ath10k_pci nls_ascii snd_soc_hda_codec nls_cp437 kvm_intel ath10k_core snd_hda_ext_core vfat ath hid_multitouch fat snd_soc_core kvm hid_generic mac80211 snd_compress crct10dif_pclmul dell_pc snd_hda_intel crc32_pclmul platform_profile iTCO_wdt ghash_clmulni_intel intel_pmc_bxt sha512_ssse3 libarc4 snd_intel_dspcfg iTCO_vendor_support mei_wdt dell_laptop dell_wmi snd_intel_sdw_acpi sha512_generic mei_hdcp mei_pxp watchdog intel_xhci_usb_role_switch i915 dell_smbios snd_hda_codec sha256_ssse3 wmi_bmof sha1_ssse3 snd_hwdep cfg80211 intel_wmi_thunderbolt snd_hda_core i2c_algo_bit rapl dell_wmi_descriptor drm_buddy processor_thermal_device_pci_legacy snd_pcm intel_cstate dcdbas intel_gtt intel_soc_dts_iosf intel_rapl_msr dell_smm_hwmon intel_uncore rfkill pcspkr processor_thermal_device i2c_i801 ucsi_acpi snd_timer processor_thermal_wt_hint drm_display_helper mei_me snd xhci_pci typec_ucsi intel_lpss_pci roles mei i2c_smbus i2c_hid_acpi soundcore
[16805.003046]  processor_thermal_rfim intel_pmc_core xhci_hcd i2c_hid typec intel_lpss ttm intel_vsec video hid soc_button_array intel_vbtn int3403_thermal wmi drm_kms_helper int3400_thermal processor_thermal_rapl idma64 pmt_telemetry battery ac pmt_class intel_rapl_common intel_pch_thermal acpi_thermal_rel usbcore processor_thermal_wt_req processor_thermal_power_floor intel_hid processor_thermal_mbox int340x_thermal_zone usb_common acpi_pad sparse_keymap button msr parport_pc ppdev lp parport efi_pstore drm configfs nfnetlink efivarfs autofs4 ext4 crc16 mbcache jbd2 dm_crypt dm_mod nvme evdev crc32c_intel serio_raw nvme_core aesni_intel gf128mul crypto_simd cryptd
[16805.003333] CPU: 3 UID: 0 PID: 65835 Comm: kworker/u16:23 Tainted: G     U             6.12.0-08446-g228a1157fb9f #29
[16805.003342] Tainted: [U]=USER
[16805.003348] Hardware name: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022
[16805.003357] Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
[16805.003420] RIP: 0010:ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003440] Code: 83 c4 08 48 89 df 5b 5d 41 5c 41 5d 41 5e 41 5f e9 5e f2 ff ff 0f 0b e9 48 ff ff ff 0f 0b e9 81 fe ff ff 0f 0b e9 3a ff ff ff <0f> 0b e9 73 fe ff ff 41 8b b6 a0 04 00 00 89 f2 89 c1 48 c7 c6 9e
[16805.003447] RSP: 0018:ffffa934872af6f0 EFLAGS: 00010246
[16805.003458] RAX: 0000000000000001 RBX: ffff93033d032000 RCX: 0000000000000000
[16805.003465] RDX: 0000000000000001 RSI: ffff9303391be080 RDI: ffff93033d032000
[16805.003472] RBP: ffff9303391be080 R08: ffff93066f1d70c0 R09: 0000000000000000
[16805.003478] R10: 0000000000000006 R11: 00000000ffffffff R12: ffff9303391be0a0
[16805.003485] R13: ffff9303391be080 R14: ffff930334941e38 R15: ffff9303391be080
[16805.003492] FS:  0000000000000000(0000) GS:ffff93066f180000(0000) knlGS:0000000000000000
[16805.003499] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[16805.003505] CR2: 00007f1bbb6c7bf8 CR3: 0000000378e21001 CR4: 00000000003726f0
[16805.003513] Call Trace:
[16805.003521]  <TASK>
[16805.003528]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003547]  ? __warn.cold+0x93/0xf8
[16805.003558]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003583]  ? report_bug+0xfb/0x140
[16805.003600]  ? handle_bug+0x54/0x90
[16805.003611]  ? exc_invalid_op+0x17/0x60
[16805.003621]  ? asm_exc_invalid_op+0x1a/0x20
[16805.003692]  ? ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
[16805.003722]  ath10k_mac_op_change_chanctx+0x11a/0x150 [ath10k_core]
[16805.003750]  drv_change_chanctx+0x40/0xe0 [mac80211]
[16805.003815]  _ieee80211_change_chanctx+0x207/0x3d0 [mac80211]
[16805.003873]  ieee80211_recalc_chanctx_chantype+0x1df/0x250 [mac80211]
[16805.003944]  ieee80211_link_change_chanreq+0x2c2/0x2e0 [mac80211]
[16805.004008]  ieee80211_config_bw.cold+0xd6/0x105 [mac80211]
[16805.004088]  ieee80211_rx_mgmt_assoc_resp.cold+0x949/0x1b29 [mac80211]
[16805.004258]  ieee80211_iface_work+0x37f/0x470 [mac80211]
[16805.004314]  cfg80211_wiphy_work+0xe9/0x160 [cfg80211]
[16805.004370]  process_one_work+0x171/0x320
[16805.004387]  worker_thread+0x24e/0x380
[16805.004404]  ? rescuer_thread+0x480/0x480
[16805.004413]  kthread+0xcf/0x100
[16805.004423]  ? kthread_park+0x80/0x80
[16805.004436]  ret_from_fork+0x31/0x50
[16805.004445]  ? kthread_park+0x80/0x80
[16805.004456]  ret_from_fork_asm+0x11/0x20
[16805.004487]  </TASK>
[16805.004494] ---[ end trace 0000000000000000 ]---
[16805.004521] ------------[ cut here ]------------
[16805.004527] WARNING: CPU: 3 PID: 65835 at drivers/net/wireless/ath/ath10k/mac.c:8775 ath10k_mac_update_vif_chan+0x230/0x2e0 [ath10k_core]
[16805.004547] Modules linked in: snd_usb_audio snd_usbmidi_lib snd_rawmidi cpuid sctp sd_mod usb_storage scsi_mod scsi_common r8153_ecm cdc_ether usbnet r8152 mii rfcomm cmac algif_hash algif_skcipher af_alg ctr ccm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device l2tp_ppp l2tp_netlink l2tp_core ip6_udp_tunnel udp_tunnel pppox ppp_generic slhc xfrm_interface xfrm6_tunnel tunnel6 xfrm_user xfrm_algo uvcvideo snd_hda_codec_hdmi btusb btrtl videobuf2_vmalloc btintel videobuf2_memops uvc btbcm videobuf2_v4l2 videodev videobuf2_common bluetooth usbhid mc ecdh_generic ecc snd_ctl_led snd_hda_codec_realtek snd_hda_codec_generic snd_hda_scodec_component joydev snd_sof_pci_intel_skl snd_sof_intel_hda_generic snd_soc_acpi_intel_match snd_soc_acpi binfmt_misc snd_soc_acpi_intel_sdca_quirks snd_sof_pci snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence soundwire_bus snd_soc_sdca snd_sof_intel_hda_common snd_soc_hdac_hda snd_sof_intel_hda_mlink snd_sof_intel_hda snd_sof x86_pkg_temp_thermal
[16805.004899]  intel_powerclamp snd_sof_utils coretemp snd_soc_avs ath10k_pci nls_ascii snd_soc_hda_codec nls_cp437 kvm_intel ath10k_core snd_hda_ext_core vfat ath hid_multitouch fat snd_soc_core kvm hid_generic mac80211 snd_compress crct10dif_pclmul dell_pc snd_hda_intel crc32_pclmul platform_profile iTCO_wdt ghash_clmulni_intel intel_pmc_bxt sha512_ssse3 libarc4 snd_intel_dspcfg iTCO_vendor_support mei_wdt dell_laptop dell_wmi snd_intel_sdw_acpi sha512_generic mei_hdcp mei_pxp watchdog intel_xhci_usb_role_switch i915 dell_smbios snd_hda_codec sha256_ssse3 wmi_bmof sha1_ssse3 snd_hwdep cfg80211 intel_wmi_thunderbolt snd_hda_core i2c_algo_bit rapl dell_wmi_descriptor drm_buddy processor_thermal_device_pci_legacy snd_pcm intel_cstate dcdbas intel_gtt intel_soc_dts_iosf intel_rapl_msr dell_smm_hwmon intel_uncore rfkill pcspkr processor_thermal_device i2c_i801 ucsi_acpi snd_timer processor_thermal_wt_hint drm_display_helper mei_me snd xhci_pci typec_ucsi intel_lpss_pci roles mei i2c_smbus i2c_hid_acpi soundcore
[16805.005267]  processor_thermal_rfim intel_pmc_core xhci_hcd i2c_hid typec intel_lpss ttm intel_vsec video hid soc_button_array intel_vbtn int3403_thermal wmi drm_kms_helper int3400_thermal processor_thermal_rapl idma64 pmt_telemetry battery ac pmt_class intel_rapl_common intel_pch_thermal acpi_thermal_rel usbcore processor_thermal_wt_req processor_thermal_power_floor intel_hid processor_thermal_mbox int340x_thermal_zone usb_common acpi_pad sparse_keymap button msr parport_pc ppdev lp parport efi_pstore drm configfs nfnetlink efivarfs autofs4 ext4 crc16 mbcache jbd2 dm_crypt dm_mod nvme evdev crc32c_intel serio_raw nvme_core aesni_intel gf128mul crypto_simd cryptd
[16805.005548] CPU: 3 UID: 0 PID: 65835 Comm: kworker/u16:23 Tainted: G     U  W          6.12.0-08446-g228a1157fb9f #29
[16805.005557] Tainted: [U]=USER, [W]=WARN
[16805.005563] Hardware name: Dell Inc. XPS 13 9360/0596KF, BIOS 2.21.0 06/02/2022
[16805.005571] Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
[16805.005620] RIP: 0010:ath10k_mac_update_vif_chan+0x230/0x2e0 [ath10k_core]
[16805.005638] Code: 0f 85 72 ff ff ff 48 83 c4 08 48 89 df 5b 5d 41 5c 41 5d 41 5e 41 5f e9 5e f2 ff ff 0f 0b e9 48 ff ff ff 0f 0b e9 81 fe ff ff <0f> 0b e9 3a ff ff ff 0f 0b e9 73 fe ff ff 41 8b b6 a0 04 00 00 89
[16805.005645] RSP: 0018:ffffa934872af6f0 EFLAGS: 00010246
[16805.005656] RAX: 0000000080000000 RBX: ffff93033d032000 RCX: 0000000000000001
[16805.005663] RDX: ffffa934872af6c0 RSI: 00000000fffffe00 RDI: ffffffffc16439e2
[16805.005669] RBP: ffff9303391be080 R08: ffff93066f1d70c0 R09: 0000000000000000
[16805.005676] R10: 0000000000000006 R11: 00000000ffffffff R12: ffff9303391be0a0
[16805.005682] R13: ffff930334941e38 R14: ffff9303349422c8 R15: ffff93033d0335d0
[16805.005689] FS:  0000000000000000(0000) GS:ffff93066f180000(0000) knlGS:0000000000000000
[16805.005696] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[16805.005702] CR2: 00007f1bbb6c7bf8 CR3: 0000000378e21001 CR4: 00000000003726f0
[16805.005709] Call Trace:
[16805.005716]  <TASK>
[16805.005723]  ? ath10k_mac_update_vif_chan+0x230/0x2e0 [ath10k_core]
[16805.005740]  ? __warn.cold+0x93/0xf8
[16805.005749]  ? ath10k_mac_update_vif_chan+0x230/0x2e0 [ath10k_core]
[16805.005771]  ? report_bug+0xfb/0x140
[16805.005787]  ? handle_bug+0x54/0x90
[16805.005797]  ? exc_invalid_op+0x17/0x60
[16805.005807]  ? asm_exc_invalid_op+0x1a/0x20
[16805.005830]  ? ath10k_mac_update_vif_chan+0xe2/0x2e0 [ath10k_core]
[16805.005848]  ? ath10k_mac_update_vif_chan+0x230/0x2e0 [ath10k_core]
[16805.005876]  ath10k_mac_op_change_chanctx+0x11a/0x150 [ath10k_core]
[16805.005903]  drv_change_chanctx+0x40/0xe0 [mac80211]
[16805.005960]  _ieee80211_change_chanctx+0x207/0x3d0 [mac80211]
[16805.006016]  ieee80211_recalc_chanctx_chantype+0x1df/0x250 [mac80211]
[16805.006086]  ieee80211_link_change_chanreq+0x2c2/0x2e0 [mac80211]
[16805.006150]  ieee80211_config_bw.cold+0xd6/0x105 [mac80211]
[16805.006229]  ieee80211_rx_mgmt_assoc_resp.cold+0x949/0x1b29 [mac80211]
[16805.006397]  ieee80211_iface_work+0x37f/0x470 [mac80211]
[16805.006451]  cfg80211_wiphy_work+0xe9/0x160 [cfg80211]
[16805.006500]  process_one_work+0x171/0x320
[16805.006517]  worker_thread+0x24e/0x380
[16805.006533]  ? rescuer_thread+0x480/0x480
[16805.006542]  kthread+0xcf/0x100
[16805.006551]  ? kthread_park+0x80/0x80
[16805.006564]  ret_from_fork+0x31/0x50
[16805.006573]  ? kthread_park+0x80/0x80
[16805.006583]  ret_from_fork_asm+0x11/0x20
[16805.006614]  </TASK>
[16805.006620] ---[ end trace 0000000000000000 ]---
[16805.009976] wlp58s0: associated
[16805.079981] wlp58s0: Limiting TX power to 20 (20 - 0) dBm as advertised by 88:71:b1:81:93:1a
[17112.157206] wlp58s0: disconnect from AP 88:71:b1:81:93:1a for new auth to 88:71:b1:81:93:1b
[17112.246492] wlp58s0: authenticate with 88:71:b1:81:93:1b (local address=9c:b6:d0:d1:6a:b1)
[17112.246503] wlp58s0: send auth to 88:71:b1:81:93:1b (try 1/3)
[17112.248273] wlp58s0: authenticated
[17112.252596] wlp58s0: associate with 88:71:b1:81:93:1b (try 1/3)
[17112.284988] wlp58s0: RX ReassocResp from 88:71:b1:81:93:1b (capab=0x1011 status=0 aid=1)
[17112.288865] wlp58s0: associated
[17112.362542] wlp58s0: Limiting TX power to 30 (30 - 0) dBm as advertised by 88:71:b1:81:93:1b
[20644.922712] wlp58s0: deauthenticating from 88:71:b1:81:93:1b by local choice (Reason: 3=DEAUTH_LEAVING)
[20646.794825] PM: suspend entry (deep)
[20646.822562] Filesystems sync: 0.027 seconds
[20646.828779] Freezing user space processes
[20646.833984] Freezing user space processes completed (elapsed 0.005 seconds)
[20646.834021] OOM killer disabled.
[20646.834043] Freezing remaining freezable tasks
[20646.838312] Freezing remaining freezable tasks completed (elapsed 0.004 seconds)
[20646.838483] printk: Suspending console(s) (use no_console_suspend to debug)
[20647.458670] ACPI: EC: interrupt blocked
[20647.493587] ACPI: PM: Preparing to enter system sleep state S3
[20647.572525] ACPI: EC: event blocked
[20647.572543] ACPI: EC: EC stopped
[20647.572559] ACPI: PM: Saving platform NVS memory
[20647.576029] Disabling non-boot CPUs ...
[20647.579864] smpboot: CPU 3 is now offline
[20647.588507] smpboot: CPU 2 is now offline
[20647.596148] smpboot: CPU 1 is now offline
[20647.605693] ACPI: PM: Low-level resume complete
[20647.605748] ACPI: EC: EC started
[20647.605752] ACPI: PM: Restoring platform NVS memory
[20647.607853] Enabling non-boot CPUs ...
[20647.607919] smpboot: Booting Node 0 Processor 1 APIC 0x2
[20647.608959] CPU1 is up
[20647.609017] smpboot: Booting Node 0 Processor 2 APIC 0x1
[20647.610206] CPU2 is up
[20647.610261] smpboot: Booting Node 0 Processor 3 APIC 0x3
[20647.611291] CPU3 is up
[20647.617045] ACPI: PM: Waking up from system sleep state S3
[20647.815758] ACPI: EC: interrupt unblocked
[20647.843839] ACPI: EC: event unblocked
[20647.847278] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[20647.847309] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[20647.860571] nvme nvme0: 4/0/0 default/read/poll queues
[20647.876150] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[20647.876164] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[20647.876173] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[20648.097857] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[20648.354031] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[20648.609712] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[20648.816118] OOM killer enabled.
[20648.816131] Restarting tasks ... done.
[20648.818667] random: crng reseeded on system resumption
[20649.117450] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[20649.127394] PM: suspend exit
[20649.132182] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[20649.132194] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[20649.493580] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[20649.523206] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[20649.780637] Bluetooth: MGMT ver 1.23
[20650.513431] usb 1-1: new low-speed USB device number 7 using xhci_hcd
[20650.657600] usb 1-1: New USB device found, idVendor=0bf8, idProduct=101e, bcdDevice= 1.09
[20650.657642] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[20650.657671] usb 1-1: Product: Fujitsu Keyboard
[20650.657696] usb 1-1: Manufacturer: Fujitsu
[20650.682220] input: Fujitsu Fujitsu Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:0BF8:101E.0009/input/input52
[20650.803198] hid-generic 0003:0BF8:101E.0009: input,hidraw2: USB HID v1.10 Keyboard [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-1/input0
[20650.820522] input: Fujitsu Fujitsu Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.1/0003:0BF8:101E.000A/input/input53
[20650.874941] input: Fujitsu Fujitsu Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.1/0003:0BF8:101E.000A/input/input54
[20650.876991] hid-generic 0003:0BF8:101E.000A: input,hiddev1,hidraw3: USB HID v1.10 Device [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-1/input1
[20655.161615] wlp58s0: VHT information is missing, disabling VHT
[20655.198331] wlp58s0: authenticate with 6c:f3:7f:10:ae:18 (local address=9c:b6:d0:d1:6a:b1)
[20655.198342] wlp58s0: send auth to 6c:f3:7f:10:ae:18 (try 1/3)
[20655.215970] wlp58s0: authenticated
[20655.217398] wlp58s0: associate with 6c:f3:7f:10:ae:18 (try 1/3)
[20655.227340] wlp58s0: RX AssocResp from 6c:f3:7f:10:ae:18 (capab=0x411 status=0 aid=4)
[20655.231010] wlp58s0: associated
[20661.161379] usb 1-2: new low-speed USB device number 8 using xhci_hcd
[20661.301769] usb 1-2: New USB device found, idVendor=046d, idProduct=c077, bcdDevice=72.00
[20661.301791] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[20661.301799] usb 1-2: Product: USB Optical Mouse
[20661.301815] usb 1-2: Manufacturer: Logitech
[20661.320686] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C077.000B/input/input55
[20661.322969] hid-generic 0003:046D:C077.000B: input,hidraw4: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-2/input0
[20666.308984] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port
[20666.309090] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[20666.309141] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[20666.309203] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[20666.309346] pci 0000:01:00.0: enabling Extended Tags
[20666.309680] pci 0000:01:00.0: supports D1 D2
[20666.309702] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[20666.309942] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[20666.319756] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[20666.319884] pci 0000:02:00.0: PCI bridge to [bus 03]
[20666.319937] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[20666.320037] pci 0000:02:00.0: enabling Extended Tags
[20666.320456] pci 0000:02:00.0: supports D1 D2
[20666.320482] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[20666.322564] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[20666.322686] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[20666.322738] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[20666.322793] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[20666.322860] pci 0000:02:01.0: enabling Extended Tags
[20666.323284] pci 0000:02:01.0: supports D1 D2
[20666.323311] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[20666.325375] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[20666.325497] pci 0000:02:02.0: PCI bridge to [bus 39]
[20666.325550] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[20666.325645] pci 0000:02:02.0: enabling Extended Tags
[20666.326060] pci 0000:02:02.0: supports D1 D2
[20666.326086] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[20666.328293] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[20666.328863] pci 0000:02:00.0: PCI bridge to [bus 03]
[20666.329405] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[20666.330211] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint
[20666.330291] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[20666.330494] pci 0000:39:00.0: enabling Extended Tags
[20666.331013] pci 0000:39:00.0: supports D1 D2
[20666.331040] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[20666.331319] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[20666.333102] pci 0000:02:02.0: PCI bridge to [bus 39]
[20666.333278] pci_bus 0000:02: Allocating resources
[20666.333367] pci 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[20666.333404] pci 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[20666.333437] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[20666.333471] pci 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[20666.333509] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[20666.333537] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[20666.333569] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[20666.333595] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[20666.333647] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[20666.333675] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[20666.333703] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.333729] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[20666.333759] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.333786] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[20666.333829] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[20666.333856] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[20666.333886] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.333913] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[20666.333942] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.333967] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[20666.333997] pci 0000:02:00.0: PCI bridge to [bus 03]
[20666.334036] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[20666.334084] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[20666.334121] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[20666.334156] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[20666.334197] pci 0000:02:02.0: PCI bridge to [bus 39]
[20666.334232] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[20666.334276] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[20666.334312] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[20666.334345] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[20666.368683] xhci_hcd 0000:39:00.0: xHCI Host Controller
[20666.368740] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3
[20666.370068] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[20666.374670] xhci_hcd 0000:39:00.0: xHCI Host Controller
[20666.374701] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4
[20666.374728] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[20666.375560] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[20666.375579] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[20666.375596] usb usb3: Product: xHCI Host Controller
[20666.375612] usb usb3: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[20666.375627] usb usb3: SerialNumber: 0000:39:00.0
[20666.376664] hub 3-0:1.0: USB hub found
[20666.376723] hub 3-0:1.0: 2 ports detected
[20666.392529] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[20666.392548] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[20666.392562] usb usb4: Product: xHCI Host Controller
[20666.392575] usb usb4: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[20666.392588] usb usb4: SerialNumber: 0000:39:00.0
[20666.395213] hub 4-0:1.0: USB hub found
[20666.395261] hub 4-0:1.0: 2 ports detected
[20666.405997] pci_bus 0000:02: Allocating resources
[20666.406052] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[20666.406073] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[20666.406091] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[20666.406109] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[20666.406131] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[20666.406145] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[20666.406161] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[20666.406175] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[20666.406201] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[20666.406215] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[20666.406230] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.406244] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[20666.406259] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.406273] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[20666.406296] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[20666.406309] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[20666.406325] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.406338] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[20666.406353] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[20666.406367] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[20666.633497] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[20666.772897] usb 3-1: New USB device found, idVendor=2109, idProduct=2820, bcdDevice=30.03
[20666.772970] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[20666.773048] usb 3-1: Product: USB2.0 Hub             
[20666.773142] usb 3-1: Manufacturer: VIA Labs, Inc.         
[20666.811143] hub 3-1:1.0: USB hub found
[20666.811464] hub 3-1:1.0: 5 ports detected
[20666.913748] usb 4-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[20666.950325] usb 4-1: New USB device found, idVendor=2109, idProduct=0820, bcdDevice=30.03
[20666.950419] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[20666.950513] usb 4-1: Product: USB3.1 Hub             
[20666.950540] usb 4-1: Manufacturer: VIA Labs, Inc.         
[20666.975879] hub 4-1:1.0: USB hub found
[20666.977384] hub 4-1:1.0: 4 ports detected
[20667.521387] usb 3-1.1: new full-speed USB device number 3 using xhci_hcd
[20667.666933] usb 3-1.1: New USB device found, idVendor=06c4, idProduct=c412, bcdDevice= 0.06
[20667.666988] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[20667.667031] usb 3-1.1: Product: DELL DA300
[20667.667060] usb 3-1.1: Manufacturer: Bizlink
[20667.667101] usb 3-1.1: SerialNumber: MCU Ver0006
[20667.683701] hid-generic 0003:06C4:C412.000C: hiddev2,hidraw5: USB HID v1.11 Device [Bizlink DELL DA300] on usb-0000:39:00.0-1.1/input0
[20667.730294] usb 4-1.2: new SuperSpeed USB device number 3 using xhci_hcd
[20667.754520] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00
[20667.754887] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[20667.755061] usb 4-1.2: Product: USB 10/100/1000 LAN
[20667.755231] usb 4-1.2: Manufacturer: Realtek
[20667.755298] usb 4-1.2: SerialNumber: 001000001
[20667.838239] r8152-cfgselector 4-1.2: reset SuperSpeed USB device number 3 using xhci_hcd
[20667.859446] r8152 4-1.2:1.0 (unnamed net_device) (uninitialized): Using pass-thru MAC addr 18:db:f2:2d:cc:f3
[20667.907996] r8152 4-1.2:1.0 eth0: v1.12.13
[20668.014836] r8152 4-1.2:1.0 enp57s0u1u2: renamed from eth0
[20671.307777] r8152 4-1.2:1.0 enp57s0u1u2: carrier on
[22402.609781] wlp58s0: deauthenticating from 6c:f3:7f:10:ae:18 by local choice (Reason: 3=DEAUTH_LEAVING)
[37227.744893] usb 3-1.3: new full-speed USB device number 4 using xhci_hcd
[37227.900100] usb 3-1.3: New USB device found, idVendor=046d, idProduct=0a4d, bcdDevice= 1.19
[37227.900112] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[37227.900119] usb 3-1.3: Product: Logitech G430 Gaming Headset
[37227.900125] usb 3-1.3: Manufacturer: Logitech
[37228.085552] input: Logitech Logitech G430 Gaming Headset as /devices/pci0000:00/0000:00:1c.0/0000:01:00.0/0000:02:02.0/0000:39:00.0/usb3/3-1/3-1.3/3-1.3:1.3/0003:046D:0A4D.000D/input/input56
[37228.141243] hid-generic 0003:046D:0A4D.000D: input,hidraw6: USB HID v1.00 Device [Logitech Logitech G430 Gaming Headset] on usb-0000:39:00.0-1.3/input3
[43512.289457] usb 3-1.3: USB disconnect, device number 4
[44356.717707] PM: suspend entry (deep)
[44356.736972] Filesystems sync: 0.019 seconds
[44356.741353] Freezing user space processes
[44356.744651] Freezing user space processes completed (elapsed 0.003 seconds)
[44356.744660] OOM killer disabled.
[44356.744666] Freezing remaining freezable tasks
[44356.746569] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[44356.746659] printk: Suspending console(s) (use no_console_suspend to debug)
[44357.360664] ACPI: EC: interrupt blocked
[44357.395391] ACPI: PM: Preparing to enter system sleep state S3
[44357.442692] ACPI: EC: event blocked
[44357.442697] ACPI: EC: EC stopped
[44357.442701] ACPI: PM: Saving platform NVS memory
[44357.444368] Disabling non-boot CPUs ...
[44357.446225] smpboot: CPU 3 is now offline
[44357.449216] smpboot: CPU 2 is now offline
[44357.453041] smpboot: CPU 1 is now offline
[44357.460396] ACPI: PM: Low-level resume complete
[44357.460461] ACPI: EC: EC started
[44357.460467] ACPI: PM: Restoring platform NVS memory
[44357.462667] Enabling non-boot CPUs ...
[44357.462733] smpboot: Booting Node 0 Processor 1 APIC 0x2
[44357.463788] CPU1 is up
[44357.463847] smpboot: Booting Node 0 Processor 2 APIC 0x1
[44357.465012] CPU2 is up
[44357.465069] smpboot: Booting Node 0 Processor 3 APIC 0x3
[44357.466271] CPU3 is up
[44357.471983] ACPI: PM: Waking up from system sleep state S3
[44357.888739] ACPI: EC: interrupt unblocked
[44357.894695] pcieport 0000:01:00.0: Unable to change power state from unknown to D0, device inaccessible
[44357.897535] pcieport 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
[44357.897548] pcieport 0000:02:01.0: Unable to change power state from unknown to D0, device inaccessible
[44357.897557] pcieport 0000:02:02.0: Unable to change power state from unknown to D0, device inaccessible
[44357.902341] xhci_hcd 0000:39:00.0: Unable to change power state from D3hot to D0, device inaccessible
[44357.969572] ACPI: EC: event unblocked
[44357.970350] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[44357.970357] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[44357.970742] xhci_hcd 0000:39:00.0: Unable to change power state from D3cold to D0, device inaccessible
[44357.970785] xhci_hcd 0000:39:00.0: Controller not ready at resume -19
[44357.970793] xhci_hcd 0000:39:00.0: PCI post-resume error -19!
[44357.970801] xhci_hcd 0000:39:00.0: HC died; cleaning up
[44357.970831] xhci_hcd 0000:39:00.0: PM: dpm_run_callback(): pci_pm_resume returns -19
[44357.970934] xhci_hcd 0000:39:00.0: PM: failed to resume async: error -19
[44357.981145] nvme nvme0: 4/0/0 default/read/poll queues
[44357.995826] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[44357.995833] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[44357.995846] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[44358.221597] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[44358.477645] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[44358.733744] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[44360.515085] xhci_hcd 0000:39:00.0: remove, state 4
[44360.515101] usb usb4: USB disconnect, device number 1
[44360.515109] usb 4-1: USB disconnect, device number 2
[44360.515121] r8152-cfgselector 4-1.2: USB disconnect, device number 3
[44360.515248] OOM killer enabled.
[44360.515256] Restarting tasks ... 
[44360.515548] usb 3-1: USB disconnect, device number 2
[44360.515557] usb 3-1.1: USB disconnect, device number 3
[44360.517308] usb 1-1: USB disconnect, device number 7
[44360.517446] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[44360.519468] done.
[44360.519513] random: crng reseeded on system resumption
[44360.600177] xhci_hcd 0000:39:00.0: USB bus 4 deregistered
[44360.600209] xhci_hcd 0000:39:00.0: remove, state 4
[44360.600225] usb usb3: USB disconnect, device number 1
[44360.602802] xhci_hcd 0000:39:00.0: Host halt failed, -19
[44360.602814] xhci_hcd 0000:39:00.0: Host not accessible, reset failed.
[44360.603783] xhci_hcd 0000:39:00.0: USB bus 3 deregistered
[44360.646801] pcieport 0000:02:00.0: Unable to change power state from D3cold to D0, device inaccessible
[44360.660015] pci_bus 0000:03: busn_res: [bus 03] is released
[44360.665994] pci_bus 0000:04: busn_res: [bus 04-38] is released
[44360.681396] pci_bus 0000:39: busn_res: [bus 39] is released
[44360.690970] pci_bus 0000:02: busn_res: [bus 02-39] is released
[44360.834086] usb 1-2: USB disconnect, device number 8
[44360.923722] PM: suspend exit
[44360.925625] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[44360.925634] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[44361.285203] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[44361.311081] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[44361.613625] Bluetooth: MGMT ver 1.23
[44573.954446] PM: suspend entry (deep)
[44573.968079] Filesystems sync: 0.013 seconds
[44573.972261] Freezing user space processes
[44573.975992] Freezing user space processes completed (elapsed 0.003 seconds)
[44573.976005] OOM killer disabled.
[44573.976012] Freezing remaining freezable tasks
[44573.978302] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[44573.978379] printk: Suspending console(s) (use no_console_suspend to debug)
[44574.568622] ACPI: EC: interrupt blocked
[44574.604151] ACPI: PM: Preparing to enter system sleep state S3
[44574.676252] ACPI: EC: event blocked
[44574.676269] ACPI: EC: EC stopped
[44574.676285] ACPI: PM: Saving platform NVS memory
[44574.679717] Disabling non-boot CPUs ...
[44574.683323] smpboot: CPU 3 is now offline
[44574.694288] smpboot: CPU 2 is now offline
[44574.701728] smpboot: CPU 1 is now offline
[44574.713306] ACPI: PM: Low-level resume complete
[44574.713371] ACPI: EC: EC started
[44574.713378] ACPI: PM: Restoring platform NVS memory
[44574.715577] Enabling non-boot CPUs ...
[44574.715642] smpboot: Booting Node 0 Processor 1 APIC 0x2
[44574.716759] CPU1 is up
[44574.716819] smpboot: Booting Node 0 Processor 2 APIC 0x1
[44574.718034] CPU2 is up
[44574.718092] smpboot: Booting Node 0 Processor 3 APIC 0x3
[44574.719185] CPU3 is up
[44574.724897] ACPI: PM: Waking up from system sleep state S3
[44574.908070] ACPI: EC: interrupt unblocked
[44574.931391] ACPI: EC: event unblocked
[44574.933230] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[44574.933245] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[44574.944692] nvme nvme0: 4/0/0 default/read/poll queues
[44574.960906] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[44574.960912] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[44574.960917] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[44575.182542] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[44575.442563] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[44575.708069] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[44575.880078] OOM killer enabled.
[44575.880097] Restarting tasks ... done.
[44575.889011] random: crng reseeded on system resumption
[44576.232166] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[44576.522590] PM: suspend exit
[44576.523804] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[44576.523821] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[44576.880423] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[44576.906298] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[44577.210299] Bluetooth: MGMT ver 1.23
[45095.785129] PM: suspend entry (deep)
[45095.795337] Filesystems sync: 0.010 seconds
[45095.807027] Freezing user space processes
[45095.812441] Freezing user space processes completed (elapsed 0.005 seconds)
[45095.812460] OOM killer disabled.
[45095.812471] Freezing remaining freezable tasks
[45095.815223] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[45095.815323] printk: Suspending console(s) (use no_console_suspend to debug)
[45096.463390] ACPI: EC: interrupt blocked
[45096.498916] ACPI: PM: Preparing to enter system sleep state S3
[45096.566665] ACPI: EC: event blocked
[45096.566680] ACPI: EC: EC stopped
[45096.566694] ACPI: PM: Saving platform NVS memory
[45096.569765] Disabling non-boot CPUs ...
[45096.573202] smpboot: CPU 3 is now offline
[45096.580346] smpboot: CPU 2 is now offline
[45096.587348] smpboot: CPU 1 is now offline
[45096.595933] ACPI: PM: Low-level resume complete
[45096.595988] ACPI: EC: EC started
[45096.595992] ACPI: PM: Restoring platform NVS memory
[45096.598096] Enabling non-boot CPUs ...
[45096.598161] smpboot: Booting Node 0 Processor 1 APIC 0x2
[45096.599216] CPU1 is up
[45096.599274] smpboot: Booting Node 0 Processor 2 APIC 0x1
[45096.600424] CPU2 is up
[45096.600482] smpboot: Booting Node 0 Processor 3 APIC 0x3
[45096.601518] CPU3 is up
[45096.607294] ACPI: PM: Waking up from system sleep state S3
[45096.803896] ACPI: EC: interrupt unblocked
[45096.833101] ACPI: EC: event unblocked
[45096.836142] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[45096.836164] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[45096.852724] nvme nvme0: 4/0/0 default/read/poll queues
[45096.861542] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[45096.861573] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[45096.861597] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[45097.091136] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[45097.347415] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[45097.607258] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[45097.753748] OOM killer enabled.
[45097.753756] Restarting tasks ... done.
[45097.767748] random: crng reseeded on system resumption
[45098.084224] PM: suspend exit
[45098.085454] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[45098.085464] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[45098.118828] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[45098.440833] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[45098.464680] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[45098.769773] Bluetooth: MGMT ver 1.23
[45183.185104] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port
[45183.185221] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[45183.185268] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[45183.185318] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[45183.185374] pci 0000:01:00.0: enabling Extended Tags
[45183.185718] pci 0000:01:00.0: supports D1 D2
[45183.185741] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[45183.185991] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[45183.200329] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[45183.200443] pci 0000:02:00.0: PCI bridge to [bus 03]
[45183.200488] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[45183.200574] pci 0000:02:00.0: enabling Extended Tags
[45183.200948] pci 0000:02:00.0: supports D1 D2
[45183.200971] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[45183.202928] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[45183.203105] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[45183.203183] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[45183.203266] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[45183.203365] pci 0000:02:01.0: enabling Extended Tags
[45183.203995] pci 0000:02:01.0: supports D1 D2
[45183.204039] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[45183.211339] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[45183.211514] pci 0000:02:02.0: PCI bridge to [bus 39]
[45183.211593] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[45183.211732] pci 0000:02:02.0: enabling Extended Tags
[45183.212366] pci 0000:02:02.0: supports D1 D2
[45183.212412] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[45183.230857] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[45183.232507] pci 0000:02:00.0: PCI bridge to [bus 03]
[45183.233278] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[45183.235371] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint
[45183.235484] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[45183.235761] pci 0000:39:00.0: enabling Extended Tags
[45183.238732] pci 0000:39:00.0: supports D1 D2
[45183.238782] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[45183.239181] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[45183.259613] pci 0000:02:02.0: PCI bridge to [bus 39]
[45183.259845] pci_bus 0000:02: Allocating resources
[45183.259982] pci 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[45183.260043] pci 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[45183.260098] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[45183.260154] pci 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[45183.260217] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[45183.260262] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[45183.260311] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[45183.260351] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[45183.260434] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[45183.260479] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[45183.260528] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.260572] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[45183.260633] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.260677] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[45183.260750] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[45183.260794] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[45183.260842] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.260885] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[45183.260933] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.260978] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[45183.261029] pci 0000:02:00.0: PCI bridge to [bus 03]
[45183.261090] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[45183.261166] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[45183.261225] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[45183.261278] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[45183.261342] pci 0000:02:02.0: PCI bridge to [bus 39]
[45183.261398] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[45183.261467] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[45183.261523] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[45183.261576] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[45183.276827] xhci_hcd 0000:39:00.0: xHCI Host Controller
[45183.277033] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3
[45183.278643] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[45183.286828] xhci_hcd 0000:39:00.0: xHCI Host Controller
[45183.286898] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4
[45183.286964] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[45183.287785] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[45183.287836] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[45183.287881] usb usb3: Product: xHCI Host Controller
[45183.287924] usb usb3: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[45183.287966] usb usb3: SerialNumber: 0000:39:00.0
[45183.293028] hub 3-0:1.0: USB hub found
[45183.293185] hub 3-0:1.0: 2 ports detected
[45183.309299] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[45183.309355] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[45183.309399] usb usb4: Product: xHCI Host Controller
[45183.309442] usb usb4: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[45183.309486] usb usb4: SerialNumber: 0000:39:00.0
[45183.312898] hub 4-0:1.0: USB hub found
[45183.313043] hub 4-0:1.0: 2 ports detected
[45183.330121] pci_bus 0000:02: Allocating resources
[45183.330439] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[45183.330485] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[45183.330527] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[45183.330568] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[45183.330614] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[45183.330644] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[45183.330681] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[45183.330709] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[45183.330768] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[45183.330797] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[45183.330831] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.330859] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[45183.330888] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.330915] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[45183.330964] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[45183.330992] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[45183.331022] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.331051] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[45183.331083] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[45183.331114] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[45183.558444] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[45183.698521] usb 3-1: New USB device found, idVendor=2109, idProduct=2820, bcdDevice= 9.f3
[45183.698554] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[45183.698572] usb 3-1: Product: USB2.0 Hub             
[45183.698589] usb 3-1: Manufacturer: VIA Labs, Inc.         
[45183.706840] hub 3-1:1.0: USB hub found
[45183.707149] hub 3-1:1.0: 5 ports detected
[45183.832685] usb 4-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[45183.849702] usb 4-1: New USB device found, idVendor=2109, idProduct=0820, bcdDevice= 9.f3
[45183.849751] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[45183.849786] usb 4-1: Product: USB3.1 Hub             
[45183.849818] usb 4-1: Manufacturer: VIA Labs, Inc.         
[45183.863968] hub 4-1:1.0: USB hub found
[45183.864471] hub 4-1:1.0: 4 ports detected
[45184.434496] usb 3-1.1: new full-speed USB device number 3 using xhci_hcd
[45184.577592] usb 3-1.1: New USB device found, idVendor=06c4, idProduct=c412, bcdDevice= 0.01
[45184.577621] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[45184.577637] usb 3-1.1: Product: DELL DA300
[45184.577652] usb 3-1.1: Manufacturer: Bizlink
[45184.577665] usb 3-1.1: SerialNumber: MCU Ver0001
[45184.596188] hid-generic 0003:06C4:C412.000E: hiddev1,hidraw2: USB HID v1.11 Device [Bizlink DELL DA300] on usb-0000:39:00.0-1.1/input0
[45184.654279] usb 4-1.2: new SuperSpeed USB device number 3 using xhci_hcd
[45184.672451] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00
[45184.672495] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[45184.672526] usb 4-1.2: Product: USB 10/100/1000 LAN
[45184.672554] usb 4-1.2: Manufacturer: Realtek
[45184.672582] usb 4-1.2: SerialNumber: 001000001
[45184.755143] r8152-cfgselector 4-1.2: reset SuperSpeed USB device number 3 using xhci_hcd
[45184.781298] r8152 4-1.2:1.0 (unnamed net_device) (uninitialized): Using pass-thru MAC addr 18:db:f2:2d:cc:f3
[45184.837120] r8152 4-1.2:1.0 eth0: v1.12.13
[45185.019360] r8152 4-1.2:1.0 enp57s0u1u2: renamed from eth0
[45187.612197] r8152 4-1.2:1.0 enp57s0u1u2: carrier on
[52399.408042] usb 3-1: USB disconnect, device number 2
[52399.408094] usb 3-1.1: USB disconnect, device number 3
[52399.441433] xhci_hcd 0000:39:00.0: xHCI host controller not responding, assume dead
[52399.441623] xhci_hcd 0000:39:00.0: HC died; cleaning up
[52399.442212] r8152 4-1.2:1.0 enp57s0u1u2: Stop submitting intr, status -108
[52399.588189] usb 4-1: USB disconnect, device number 2
[52399.588243] r8152-cfgselector 4-1.2: USB disconnect, device number 3
[52399.650872] xhci_hcd 0000:39:00.0: remove, state 1
[52399.650975] usb usb4: USB disconnect, device number 1
[52399.783191] xhci_hcd 0000:39:00.0: USB bus 4 deregistered
[52399.783365] xhci_hcd 0000:39:00.0: remove, state 1
[52399.783456] usb usb3: USB disconnect, device number 1
[52399.795847] xhci_hcd 0000:39:00.0: Host halt failed, -19
[52399.795927] xhci_hcd 0000:39:00.0: Host not accessible, reset failed.
[52399.801031] xhci_hcd 0000:39:00.0: USB bus 3 deregistered
[52399.865484] pci_bus 0000:02: Allocating resources
[52399.865627] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[52399.865718] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[52399.865779] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[52399.865858] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[52399.865951] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52399.866011] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52399.866090] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52399.866151] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52399.866272] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52399.866324] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52399.866384] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52399.866435] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52399.866494] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52399.866548] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52399.866634] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52399.866694] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52399.866755] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52399.866818] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52399.866880] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52399.866937] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52404.645028] pcieport 0000:02:00.0: Unable to change power state from D3hot to D0, device inaccessible
[52404.663126] pci_bus 0000:03: busn_res: [bus 03] is released
[52404.664920] pci_bus 0000:04: busn_res: [bus 04-38] is released
[52404.672978] pci_bus 0000:39: busn_res: [bus 39] is released
[52404.676771] pci_bus 0000:02: busn_res: [bus 02-39] is released
[52484.640293] PM: suspend entry (deep)
[52484.658708] Filesystems sync: 0.018 seconds
[52484.662449] Freezing user space processes
[52484.665475] Freezing user space processes completed (elapsed 0.003 seconds)
[52484.665485] OOM killer disabled.
[52484.665490] Freezing remaining freezable tasks
[52484.667526] Freezing remaining freezable tasks completed (elapsed 0.002 seconds)
[52484.667585] printk: Suspending console(s) (use no_console_suspend to debug)
[52485.276507] ACPI: EC: interrupt blocked
[52485.309182] ACPI: PM: Preparing to enter system sleep state S3
[52485.354479] ACPI: EC: event blocked
[52485.354484] ACPI: EC: EC stopped
[52485.354488] ACPI: PM: Saving platform NVS memory
[52485.356197] Disabling non-boot CPUs ...
[52485.358328] smpboot: CPU 3 is now offline
[52485.363262] smpboot: CPU 2 is now offline
[52485.370326] smpboot: CPU 1 is now offline
[52485.378167] ACPI: PM: Low-level resume complete
[52485.378221] ACPI: EC: EC started
[52485.378225] ACPI: PM: Restoring platform NVS memory
[52485.380333] Enabling non-boot CPUs ...
[52485.380398] smpboot: Booting Node 0 Processor 1 APIC 0x2
[52485.381481] CPU1 is up
[52485.381538] smpboot: Booting Node 0 Processor 2 APIC 0x1
[52485.382687] CPU2 is up
[52485.382743] smpboot: Booting Node 0 Processor 3 APIC 0x3
[52485.383777] CPU3 is up
[52485.389517] ACPI: PM: Waking up from system sleep state S3
[52490.527028] ACPI: EC: interrupt unblocked
[52490.599744] ACPI: EC: event unblocked
[52490.603278] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
[52490.603312] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
[52490.616026] nvme nvme0: 4/0/0 default/read/poll queues
[52490.631725] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
[52490.631736] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
[52490.631743] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
[52490.881752] usb 1-5: reset high-speed USB device number 4 using xhci_hcd
[52491.137772] usb 1-3: reset full-speed USB device number 2 using xhci_hcd
[52491.393486] usb 1-4: reset full-speed USB device number 3 using xhci_hcd
[52491.540087] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[52491.542197] OOM killer enabled.
[52491.542203] Restarting tasks ... done.
[52491.545540] random: crng reseeded on system resumption
[52491.547150] pci 0000:01:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Upstream Port
[52491.547221] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[52491.547249] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[52491.547279] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[52491.547316] pci 0000:01:00.0: enabling Extended Tags
[52491.548572] Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00000302.bin
[52491.548580] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8, firmware rome 0x302 build 0x111
[52491.549252] pci 0000:01:00.0: supports D1 D2
[52491.549265] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[52491.549420] pci 0000:01:00.0: 15.752 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x2 link at 0000:00:1c.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[52491.647871] pci 0000:02:00.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[52491.647949] pci 0000:02:00.0: PCI bridge to [bus 03]
[52491.647979] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[52491.648041] pci 0000:02:00.0: enabling Extended Tags
[52491.648252] pci 0000:02:00.0: supports D1 D2
[52491.648260] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[52491.653784] pci 0000:02:01.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[52491.653843] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[52491.653867] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[52491.653894] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[52491.653926] pci 0000:02:01.0: enabling Extended Tags
[52491.660925] pci 0000:02:01.0: supports D1 D2
[52491.660936] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[52491.671379] pci 0000:02:02.0: [8086:1576] type 01 class 0x060400 PCIe Switch Downstream Port
[52491.671429] pci 0000:02:02.0: PCI bridge to [bus 39]
[52491.671446] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[52491.671484] pci 0000:02:02.0: enabling Extended Tags
[52491.682926] pci 0000:02:02.0: supports D1 D2
[52491.682940] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[52491.688835] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[52491.691897] pci 0000:02:00.0: PCI bridge to [bus 03]
[52491.694630] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[52491.694993] pci 0000:39:00.0: [8086:15b5] type 00 class 0x0c0330 PCIe Endpoint
[52491.695044] pci 0000:39:00.0: BAR 0 [mem 0xd9f00000-0xd9f0ffff]
[52491.695173] pci 0000:39:00.0: enabling Extended Tags
[52491.703903] pci 0000:39:00.0: supports D1 D2
[52491.703910] pci 0000:39:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[52491.704062] pci 0000:39:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:02:02.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[52491.709009] pci 0000:02:02.0: PCI bridge to [bus 39]
[52491.709097] pci_bus 0000:02: Allocating resources
[52491.710304] pci 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[52491.710346] pci 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[52491.710374] pci 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[52491.710400] pci 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[52491.710428] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52491.710452] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52491.710477] pci 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52491.710499] pci 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52491.710544] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52491.710566] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52491.710591] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.710614] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52491.710625] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.710645] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52491.710674] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52491.710701] pci 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52491.710714] pci 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.710724] pci 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52491.710736] pci 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.710747] pci 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52491.710760] pci 0000:02:00.0: PCI bridge to [bus 03]
[52491.710776] pci 0000:02:00.0:   bridge window [mem 0xda000000-0xda0fffff]
[52491.710800] pci 0000:02:01.0: PCI bridge to [bus 04-38]
[52491.710817] pci 0000:02:01.0:   bridge window [mem 0xc4000000-0xd9efffff]
[52491.710832] pci 0000:02:01.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[52491.710850] pci 0000:02:02.0: PCI bridge to [bus 39]
[52491.710867] pci 0000:02:02.0:   bridge window [mem 0xd9f00000-0xd9ffffff]
[52491.710888] pci 0000:01:00.0: PCI bridge to [bus 02-39]
[52491.710905] pci 0000:01:00.0:   bridge window [mem 0xc4000000-0xda0fffff]
[52491.710919] pci 0000:01:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[52491.734225] pci 0000:39:00.0: quirk_usb_early_handoff+0x0/0x6c0 took 11350 usecs
[52491.739033] xhci_hcd 0000:39:00.0: xHCI Host Controller
[52491.739056] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 3
[52491.740227] xhci_hcd 0000:39:00.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000200009810
[52491.740895] xhci_hcd 0000:39:00.0: xHCI Host Controller
[52491.740906] xhci_hcd 0000:39:00.0: new USB bus registered, assigned bus number 4
[52491.740914] xhci_hcd 0000:39:00.0: Host supports USB 3.1 Enhanced SuperSpeed
[52491.741018] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.12
[52491.741025] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[52491.741030] usb usb3: Product: xHCI Host Controller
[52491.741036] usb usb3: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[52491.741041] usb usb3: SerialNumber: 0000:39:00.0
[52491.741708] hub 3-0:1.0: USB hub found
[52491.741751] hub 3-0:1.0: 2 ports detected
[52491.762689] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.12
[52491.762704] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[52491.762716] usb usb4: Product: xHCI Host Controller
[52491.762727] usb usb4: Manufacturer: Linux 6.12.0-08446-g228a1157fb9f xhci-hcd
[52491.762738] usb usb4: SerialNumber: 0000:39:00.0
[52491.767184] hub 4-0:1.0: USB hub found
[52491.767214] hub 4-0:1.0: 2 ports detected
[52491.782851] pci_bus 0000:02: Allocating resources
[52491.782890] pcieport 0000:02:01.0: bridge window [io  0x1000-0x0fff] to [bus 04-38] add_size 1000
[52491.782907] pcieport 0000:02:02.0: bridge window [io  0x1000-0x0fff] to [bus 39] add_size 1000
[52491.782921] pcieport 0000:02:02.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 39] add_size 200000 add_align 100000
[52491.782936] pcieport 0000:01:00.0: bridge window [io  0x1000-0x0fff] to [bus 02-39] add_size 2000
[52491.782954] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52491.782966] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52491.782979] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: can't assign; no space
[52491.782991] pcieport 0000:01:00.0: bridge window [io  size 0x2000]: failed to assign
[52491.783012] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52491.783023] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52491.783034] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.783044] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52491.783056] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.783064] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52491.783080] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: can't assign; no space
[52491.783090] pcieport 0000:02:02.0: bridge window [mem size 0x00200000 64bit pref]: failed to assign
[52491.783101] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.783112] pcieport 0000:02:02.0: bridge window [io  size 0x1000]: failed to assign
[52491.783124] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: can't assign; no space
[52491.783134] pcieport 0000:02:01.0: bridge window [io  size 0x1000]: failed to assign
[52491.843682] PM: suspend exit
[52491.909070] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[52491.934946] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[52492.009160] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[52492.153194] usb 3-1: New USB device found, idVendor=2109, idProduct=2820, bcdDevice= 9.f3
[52492.153206] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[52492.153213] usb 3-1: Product: USB2.0 Hub             
[52492.153219] usb 3-1: Manufacturer: VIA Labs, Inc.         
[52492.157125] hub 3-1:1.0: USB hub found
[52492.159210] hub 3-1:1.0: 5 ports detected
[52492.238399] Bluetooth: MGMT ver 1.23
[52492.284617] usb 4-1: new SuperSpeed Plus Gen 2x1 USB device number 2 using xhci_hcd
[52492.304757] usb 4-1: New USB device found, idVendor=2109, idProduct=0820, bcdDevice= 9.f3
[52492.304779] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[52492.304794] usb 4-1: Product: USB3.1 Hub             
[52492.304808] usb 4-1: Manufacturer: VIA Labs, Inc.         
[52492.313035] hub 4-1:1.0: USB hub found
[52492.315338] hub 4-1:1.0: 4 ports detected
[52492.861138] usb 3-1.1: new full-speed USB device number 3 using xhci_hcd
[52493.004611] usb 3-1.1: New USB device found, idVendor=06c4, idProduct=c412, bcdDevice= 0.01
[52493.004637] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[52493.004652] usb 3-1.1: Product: DELL DA300
[52493.004665] usb 3-1.1: Manufacturer: Bizlink
[52493.004677] usb 3-1.1: SerialNumber: MCU Ver0001
[52493.017044] hid-generic 0003:06C4:C412.000F: hiddev1,hidraw2: USB HID v1.11 Device [Bizlink DELL DA300] on usb-0000:39:00.0-1.1/input0
[52493.809315] usb 4-1.2: new SuperSpeed USB device number 3 using xhci_hcd
[52493.826772] usb 4-1.2: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=31.00
[52493.826811] usb 4-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[52493.826838] usb 4-1.2: Product: USB 10/100/1000 LAN
[52493.826863] usb 4-1.2: Manufacturer: Realtek
[52493.826887] usb 4-1.2: SerialNumber: 001000001
[52493.906167] r8152-cfgselector 4-1.2: reset SuperSpeed USB device number 3 using xhci_hcd
[52493.931153] r8152 4-1.2:1.0 (unnamed net_device) (uninitialized): Using pass-thru MAC addr 18:db:f2:2d:cc:f3
[52493.993430] r8152 4-1.2:1.0 eth0: v1.12.13
[52494.230743] r8152 4-1.2:1.0 enp57s0u1u2: renamed from eth0
[52497.428813] r8152 4-1.2:1.0 enp57s0u1u2: carrier on
[52692.690494] systemd-ssh-generator[112558]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[52692.690509] systemd-ssh-generator[112558]: ? connect via 'ssh .host' locally
[52692.729043] systemd-sysv-generator[112560]: SysV service '/etc/init.d/xl2tpd' lacks a native systemd unit file, automatically generating a unit file for compatibility.
[52692.729061] systemd-sysv-generator[112560]: Please update package to include a native systemd unit file.
[52692.729071] systemd-sysv-generator[112560]: ! This compatibility logic is deprecated, expect removal soon. !
[52694.115278] systemd-ssh-generator[112711]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[52694.115288] systemd-ssh-generator[112711]: ? connect via 'ssh .host' locally
[52694.127835] systemd-sysv-generator[112713]: SysV service '/etc/init.d/xl2tpd' lacks a native systemd unit file, automatically generating a unit file for compatibility.
[52694.127852] systemd-sysv-generator[112713]: Please update package to include a native systemd unit file.
[52694.127863] systemd-sysv-generator[112713]: ! This compatibility logic is deprecated, expect removal soon. !
[52695.833358] systemd-ssh-generator[112891]: Binding SSH to AF_UNIX socket /run/ssh-unix-local/socket.
[52695.833372] systemd-ssh-generator[112891]: ? connect via 'ssh .host' locally
[52695.842200] systemd-sysv-generator[112893]: SysV service '/etc/init.d/xl2tpd' lacks a native systemd unit file, automatically generating a unit file for compatibility.
[52695.842210] systemd-sysv-generator[112893]: Please update package to include a native systemd unit file.
[52695.842216] systemd-sysv-generator[112893]: ! This compatibility logic is deprecated, expect removal soon. !

From kvalo at kernel.org  Wed Nov 27 03:36:49 2024
From: kvalo at kernel.org (Kalle Valo)
Date: Wed, 27 Nov 2024 13:36:49 +0200
Subject: WARNING: drivers/net/wireless/ath/ath10k/mac.c:8750
 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
In-Reply-To: <637c5bb4-5278-44be-9ac3-9c0ef9297162@molgen.mpg.de> (Paul
	Menzel's message of "Tue, 26 Nov 2024 09:58:22 +0100")
References: <637c5bb4-5278-44be-9ac3-9c0ef9297162@molgen.mpg.de>
Message-ID: <8734jcx60e.fsf@kernel.org>

Paul Menzel <pmenzel at molgen.mpg.de> writes:

> On the Dell XPS 13 9360 with Linux 6.12.0-08446-g228a1157fb9f, I
> noticed the trace below:

For others, commit 228a1157fb9f is from current merge window so the
first release will be in v6.13-rc1.

> [16805.002289] ------------[ cut here ]------------
> [16805.002296] WARNING: CPU: 3 PID: 65835 at
> drivers/net/wireless/ath/ath10k/mac.c:8750
> ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]

[...]

> I do not see such a message in the logs since September 19th, so I
> believe it?s a regression.

Have you seen it only this one time or multiple times?

What kernels have you been testing prior? I'm trying to pinpoint what
versions kernel version work and what have this warning.

-- 
https://patchwork.kernel.org/project/linux-wireless/list/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches


From pmenzel at molgen.mpg.de  Thu Nov 28 15:01:55 2024
From: pmenzel at molgen.mpg.de (Paul Menzel)
Date: Fri, 29 Nov 2024 00:01:55 +0100
Subject: WARNING: drivers/net/wireless/ath/ath10k/mac.c:8750
 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
In-Reply-To: <8734jcx60e.fsf@kernel.org>
References: <637c5bb4-5278-44be-9ac3-9c0ef9297162@molgen.mpg.de>
 <8734jcx60e.fsf@kernel.org>
Message-ID: <5c9bf757-a035-499c-a1ef-ac33c1c6e75b@molgen.mpg.de>

Dear Kalle,


Thank you for your reply.


Am 27.11.24 um 12:36 schrieb Kalle Valo:
> Paul Menzel writes:
> 
>> On the Dell XPS 13 9360 with Linux 6.12.0-08446-g228a1157fb9f, I
>> noticed the trace below:
> 
> For others, commit 228a1157fb9f is from current merge window so the
> first release will be in v6.13-rc1.
> 
>> [16805.002289] ------------[ cut here ]------------
>> [16805.002296] WARNING: CPU: 3 PID: 65835 at drivers/net/wireless/ath/ath10k/mac.c:8750 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
> 
> [...]
> 
>> I do not see such a message in the logs since September 19th, so I
>> believe it?s a regression.
> 
> Have you seen it only this one time or multiple times?

I have seen it only this one time.

> What kernels have you been testing prior? I'm trying to pinpoint what
> versions kernel version work and what have this warning.
Before I ran 6.12.0-07749-g28eb75e178d3 without seeing this. As it only 
occurred once, that does not give any pointer though.


Kind regards,

Paul


PS:

$ last reboot
reboot   system boot  6.12.0-10296-gaa Thu Nov 28 22:42 - still running
reboot   system boot  6.12-rc6-amd64   Wed Nov 27 14:04 - 22:42 (1+08:37)
reboot   system boot  6.12.0-10296-gaa Wed Nov 27 13:21 - 14:02  (00:40)
reboot   system boot  6.12.0-09568-g2f Tue Nov 26 18:41 - crash
reboot   system boot  6.12.0-08446-g22 Sat Nov 23 12:27 - 18:40 (3+06:13)
reboot   system boot  6.12.0-07749-g28 Fri Nov 22 10:14 - 10:24 (1+00:09)
reboot   system boot  6.12.0           Wed Nov 20 09:24 - crash
reboot   system boot  6.12.0-rc7       Wed Nov 20 09:22 - 09:23  (00:01)
reboot   system boot  6.12.0-rc7       Tue Nov 12 08:19 - 23:27 (7+15:08)
reboot   system boot  6.12.0-rc7       Mon Nov 11 21:54 - 00:16  (02:21)
reboot   system boot  6.11-amd64       Mon Nov 11 21:52 - crash
reboot   system boot  6.12.0-rc7       Mon Nov 11 20:43 - 21:52  (01:08)
reboot   system boot  6.12.0-rc7       Mon Nov 11 17:51 - 17:52  (00:01)
reboot   system boot  6.12.0-rc6-00077 Fri Nov  8 08:39 - 17:50 (3+09:11)
reboot   system boot  6.12.0-rc6-00077 Thu Nov  7 07:26 - 23:24  (15:58)
reboot   system boot  6.12.0-rc5-00047 Mon Nov  4 08:26 - crash
reboot   system boot  6.12.0-rc5-00047 Mon Nov  4 05:42 - 05:43  (00:00)
reboot   system boot  6.12.0-rc5-00047 Sun Nov  3 06:54 - 22:10  (15:15)
reboot   system boot  6.12.0-rc5-00047 Sat Nov  2 07:34 - 22:05  (14:31)


From kvalo at kernel.org  Fri Nov 29 00:53:48 2024
From: kvalo at kernel.org (Kalle Valo)
Date: Fri, 29 Nov 2024 10:53:48 +0200
Subject: WARNING: drivers/net/wireless/ath/ath10k/mac.c:8750
 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
In-Reply-To: <5c9bf757-a035-499c-a1ef-ac33c1c6e75b@molgen.mpg.de> (Paul
	Menzel's message of "Fri, 29 Nov 2024 00:01:55 +0100")
References: <637c5bb4-5278-44be-9ac3-9c0ef9297162@molgen.mpg.de>
	<8734jcx60e.fsf@kernel.org>
	<5c9bf757-a035-499c-a1ef-ac33c1c6e75b@molgen.mpg.de>
Message-ID: <8734jav2sj.fsf@kernel.org>

Paul Menzel <pmenzel at molgen.mpg.de> writes:

> Dear Kalle,
>
>
> Thank you for your reply.
>
>
> Am 27.11.24 um 12:36 schrieb Kalle Valo:
>> Paul Menzel writes:
>> 
>>> On the Dell XPS 13 9360 with Linux 6.12.0-08446-g228a1157fb9f, I
>>> noticed the trace below:
>> For others, commit 228a1157fb9f is from current merge window so the
>> first release will be in v6.13-rc1.
>> 
>>> [16805.002289] ------------[ cut here ]------------
>>> [16805.002296] WARNING: CPU: 3 PID: 65835 at drivers/net/wireless/ath/ath10k/mac.c:8750 ath10k_mac_update_vif_chan+0x237/0x2e0 [ath10k_core]
>> [...]
>> 
>>> I do not see such a message in the logs since September 19th, so I
>>> believe it?s a regression.
>> Have you seen it only this one time or multiple times?
>
> I have seen it only this one time.

Ok. Was it a network you regularly connect to or a new network? That
could also make a difference.

>> What kernels have you been testing prior? I'm trying to pinpoint what
>> versions kernel version work and what have this warning.
>
> Before I ran 6.12.0-07749-g28eb75e178d3 without seeing this. As it
> only occurred once, that does not give any pointer though.

Yeah, if you have seen it only once it is difficult to make any
conclusions. It could be as well an older bug which happens rarely. If
you see it again, let us know.

> PS:
>
> $ last reboot
> reboot   system boot  6.12.0-10296-gaa Thu Nov 28 22:42 - still running
> reboot   system boot  6.12-rc6-amd64   Wed Nov 27 14:04 - 22:42 (1+08:37)
> reboot   system boot  6.12.0-10296-gaa Wed Nov 27 13:21 - 14:02  (00:40)
> reboot   system boot  6.12.0-09568-g2f Tue Nov 26 18:41 - crash
> reboot   system boot  6.12.0-08446-g22 Sat Nov 23 12:27 - 18:40 (3+06:13)
> reboot   system boot  6.12.0-07749-g28 Fri Nov 22 10:14 - 10:24 (1+00:09)
> reboot   system boot  6.12.0           Wed Nov 20 09:24 - crash
> reboot   system boot  6.12.0-rc7       Wed Nov 20 09:22 - 09:23  (00:01)
> reboot   system boot  6.12.0-rc7       Tue Nov 12 08:19 - 23:27 (7+15:08)
> reboot   system boot  6.12.0-rc7       Mon Nov 11 21:54 - 00:16  (02:21)
> reboot   system boot  6.11-amd64       Mon Nov 11 21:52 - crash
> reboot   system boot  6.12.0-rc7       Mon Nov 11 20:43 - 21:52  (01:08)
> reboot   system boot  6.12.0-rc7       Mon Nov 11 17:51 - 17:52  (00:01)
> reboot   system boot  6.12.0-rc6-00077 Fri Nov  8 08:39 - 17:50 (3+09:11)
> reboot   system boot  6.12.0-rc6-00077 Thu Nov  7 07:26 - 23:24  (15:58)
> reboot   system boot  6.12.0-rc5-00047 Mon Nov  4 08:26 - crash
> reboot   system boot  6.12.0-rc5-00047 Mon Nov  4 05:42 - 05:43  (00:00)
> reboot   system boot  6.12.0-rc5-00047 Sun Nov  3 06:54 - 22:10  (15:15)
> reboot   system boot  6.12.0-rc5-00047 Sat Nov  2 07:34 - 22:05  (14:31)

Oh nice, looks really useful. I need to install that.

-- 
https://patchwork.kernel.org/project/linux-wireless/list/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches


From repk at triplefau.lt  Fri Nov 29 08:31:58 2024
From: repk at triplefau.lt (Remi Pommarel)
Date: Fri, 29 Nov 2024 17:31:58 +0100
Subject: [RESEND PATCH v3 0/2] Improve ath10k flush queue mechanism
In-Reply-To: <20215f63-e2e6-4f9a-bbbe-d7535c5ce9d2@gmail.com>
References: <cover.1732293922.git.repk@triplefau.lt>
 <20215f63-e2e6-4f9a-bbbe-d7535c5ce9d2@gmail.com>
Message-ID: <Z0nsfoiPOHiKIXvH@pilgrim>

Hi James,

On Tue, Nov 26, 2024 at 04:57:36AM -0800, James Prestwood wrote:
> Hi Remi,
> 
> On 11/22/24 8:48 AM, Remi Pommarel wrote:
> > It has been reported [0] that a 3-4 seconds (actually up to 5 sec) of
> > radio silence could be observed followed by the error below on ath10k
> > devices:
> > 
> >   ath10k_pci 0000:04:00.0: failed to flush transmit queue (skip 0 ar-state 1): 0
> > 
> > This is due to how the TX queues are flushed in ath10k. When a STA is
> > removed, mac80211 need to flush queues [1], but because ath10k does not
> > have a lightweight .flush_sta operation, ieee80211_flush_queues() is
> > called instead effectively blocking the whole queue during the drain
> > causing this radio silence. Also because ath10k_flush() waits for all
> > queued to be emptied, not only the flushed ones it could more easily
> > take up to 5 seconds to finish making the whole situation worst.
> > 
> > The first patch of this series adds a .flush_sta operation to flush only
> > specific STA traffic avoiding the need to stop whole queues and should
> > be enough in itself to fix the reported issue.
> > 
> > The second patch of this series is a proposal to improve ath10k_flush so
> > that it will be less likely to timeout waiting for non related queues to
> > drain.
> > 
> > The abose kernel warning could still be observed (e.g. flushing a dead
> > STA) but should be now harmless.
> > 
> > [0]: https://lore.kernel.org/all/CA+Xfe4FjUmzM5mvPxGbpJsF3SvSdE5_wgxvgFJ0bsdrKODVXCQ at mail.gmail.com/
> > [1]: commit 0b75a1b1e42e ("wifi: mac80211: flush queues on STA removal")
> 
> I saw in the original report that it indicated it was only for AP mode but
> after seeing this and checking some of our clients I saw that this is also
> happening in station mode too. I only have clients on 6.2 and 6.8. I can
> confirm its not occurring on 6.2, but is on 6.8. I also tried your set of
> patches but did not notice any behavior difference with or without them.
> When it happens, its always just after a roam scan, ~4 seconds go by and we
> get the failure followed by a "Connection to AP <mac> lost". Oddly the MAC
> address is all zeros.
> 
> Nov 25 09:09:50 iwd[16256]: src/station.c:station_start_roam() Using cached
> neighbor report for roam
> Nov 25 09:09:54 kernel: ath10k_pci 0000:02:00.0: failed to flush transmit
> queue (skip 0 ar-state 1): 0
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME
> notification Del Station(20)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_link_notify() event 16 on
> ifindex 7
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME
> notification Deauthenticate(39)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_deauthenticate_event()
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_mlme_notify() MLME
> notification Disconnect(48)
> Nov 25 09:09:54 iwd[16256]: src/netdev.c:netdev_disconnect_event()
> Nov 25 09:09:54 iwd[16256]: Received Deauthentication event, reason: 4,
> from_ap: false
> Nov 25 09:09:54 kernel: wlan0: Connection to AP 00:00:00:00:00:00 lost
> 
> Other times, the above logs are preceded by this:
> 
> Nov 26 00:25:25 kernel: ath10k_pci 0000:02:00.0: failed to flush sta txq
> (sta ca:55:b8:7a:91:4b skip 0 ar-state 1): 0
> 
> Note, the above logs are with your patches applied. Maybe this is a separate
> issue? Or do you think its related?

Thanks fot the test. Yes this patchset is here only to fix the issue for
AP (this caused AP to stall all traffic for every STA connected to it).
So while this issue is interesting it is not addressed by this patchset.

Out of curiosity I tried to reproduce it currently trying to roam an
ath10k sta back and forth two APs (same SSID/psk, different channels)
and wasn't able to reproduce with wpa_supplicant, didn't try with iwd
though. Or maybe the AP the sta is roaming away from has stopped
responding, in that case I don't know what can be done here as it does
not seem we want to drop pending frames (as we would prefer to deauth
cleanly from AP in main case).

In any case still I think this is a separate issue and it is also way
less critical than the AP one (one STA can create ~4sec DOS to the
entire BSS vs a STA took more time to roam away if AP crashed).

Thanks,

-- 
Remi

> 
> Thanks,
> 
> James
> 
> > 
> > V3:
> >    - Initialize empty to true to fix smatch error
> > 
> > V2:
> >    - Add Closes tag
> >    - Use atomic instead of spinlock for per sta pending frame counter
> >    - Call ath10k_htt_tx_sta_dec_pending within rcu
> >    - Rename pending_per_queue[] to num_pending_per_queue[]
> > 
> > Remi Pommarel (2):
> >    wifi: ath10k: Implement ieee80211 flush_sta callback
> >    wifi: ath10k: Flush only requested txq in ath10k_flush()
> > 
> >   drivers/net/wireless/ath/ath10k/core.h   |  2 +
> >   drivers/net/wireless/ath/ath10k/htt.h    | 11 +++-
> >   drivers/net/wireless/ath/ath10k/htt_tx.c | 49 +++++++++++++++-
> >   drivers/net/wireless/ath/ath10k/mac.c    | 75 ++++++++++++++++++++----
> >   drivers/net/wireless/ath/ath10k/txrx.c   | 11 ++--
> >   5 files changed, 127 insertions(+), 21 deletions(-)
> >