[PATCH 1/2] dt-bindings: net: wireless: ath10k: add qcom,no-msa-ready-indicator prop

[Marc Gonzalez]

On 13/03/2024 16:53, Dmitry Baryshkov wrote:

> On Wed, 13 Mar 2024 at 17:09, Marc Gonzalez wrote:
>
>> On 05/03/2024 20:20, Kalle Valo wrote:
>>
>>> Marc Gonzalez wrote:
>>>
>>>> I need to build a kernel + rootfs + FW to test the proposed solution,
>>>> then I can spin a formal submission.
>>>
>>> Yeah, please do test this to make sure we are not missing anything :)
>>
>> I used buildroot ( https://buildroot.org ) to generate a kernel + rootfs
>> for my board (a variation of qcom/msm8998-mtp.dts)
>>
>> Not sure if I must use the vendor FW blobs? Or if I can use the blobs
>> from linux-firmware-20240115.tar.xz (as supported by BR2).
>>
>>
>> All I see from the ath10k driver (with debugging cranked to the max) is:
>>
>> [    0.539801] ath10k_snoc 18800000.wifi: Adding to iommu group 0
>> [    0.541941] ath10k_snoc 18800000.wifi: snoc xo-cal-data return -22
>> [    0.543633] ath10k_snoc 18800000.wifi: supply vdd-3.3-ch1 not found, using dummy regulator
>> [    0.544002] ath10k_snoc 18800000.wifi: qmi msa.paddr: 0x0000000094400000 , msa.vaddr: 0x(____ptrval____)
>> [    0.544271] ath10k_snoc 18800000.wifi: snoc probe
>>
>>
>> # ip link
>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1000
>>     link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
>> 2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
>>     link/ether 34:27:92:82:48:ec brd ff:ff:ff:ff:ff:ff
>>
>> No wlan device at this point.
> 
> Do you have pd-mapper, rmtfs and tqftpserv running? You also need to
> have wlanmdsp.mbn in the same directory as modem.mbn for your platform
> (see how this is handled for sdm845).
> If these points are implemented and you still don't have the wlan,
> please check for tqftpserv messages in syslog.

I first tried using buildroot, which doesn't package these tools AFAICT.
I have now generated a debian rootfs, which does package them.


>> I got shell-shock from reading these setup steps:
>>
>> https://wiki.postmarketos.org/wiki/Qualcomm_Snapdragon_835_(MSM8998)#WLAN
>> https://github.com/jhugo/linux/blob/5.5rc2_wifi/README
> 
> These readmes are mostly correct. You don't need qrtr now, it is
> provided by the kernel.  pd-mapper (protection-domain-mapper),
> tqftpserv and rmtfs usually can be installed from your distro.

Can you explain a little bit why all the steps are required
just to be able to talk to the ath10k IP block?

It's just an MMIO device, right?

		wifi: wifi at 18800000 {
			compatible = "qcom,wcn3990-wifi";
			reg = <0x18800000 0x800000>;
			reg-names = "membase";

Is the IP block behind some kind of switch that must be programmed
by a remote processor on the SoC?

Regards