[PATCH] [RFC] qcom_scm: hide Kconfig symbol

Bjorn Andersson bjorn.andersson at linaro.org
Wed Sep 29 07:46:27 PDT 2021


On Wed 29 Sep 05:04 CDT 2021, Arnd Bergmann wrote:

> On Wed, Sep 29, 2021 at 11:51 AM Will Deacon <will at kernel.org> wrote:
> > On Mon, Sep 27, 2021 at 05:22:13PM +0200, Arnd Bergmann wrote:
> > >
> > > diff --git a/drivers/iommu/Kconfig b/drivers/iommu/Kconfig
> > > index 124c41adeca1..989c83acbfee 100644
> > > --- a/drivers/iommu/Kconfig
> > > +++ b/drivers/iommu/Kconfig
> > > @@ -308,7 +308,7 @@ config APPLE_DART
> > >  config ARM_SMMU
> > >       tristate "ARM Ltd. System MMU (SMMU) Support"
> > >       depends on ARM64 || ARM || (COMPILE_TEST && !GENERIC_ATOMIC64)
> > > -     depends on QCOM_SCM || !QCOM_SCM #if QCOM_SCM=m this can't be =y
> > > +     select QCOM_SCM
> > >       select IOMMU_API
> > >       select IOMMU_IO_PGTABLE_LPAE
> > >       select ARM_DMA_USE_IOMMU if ARM
> >
> > I don't want to get in the way of this patch because I'm also tired of the
> > randconfig failures caused by QCOM_SCM. However, ARM_SMMU is applicable to
> > a wide variety of (non-qcom) SoCs and so it seems a shame to require the
> > QCOM_SCM code to be included for all of those when it's not strictly needed
> > at all.
> 
> Good point, I agree that needs to be fixed. I think this additional
> change should do the trick:
> 

ARM_SMMU and QCOM_IOMMU are two separate implementations and both uses
QCOM_SCM. So both of them should select QCOM_SCM.

"Unfortunately" the Qualcomm portion of ARM_SMMU is builtin
unconditionally, so going with something like select QCOM_SCM if
ARCH_QCOM would still require the stubs in qcom_scm.h.

Regards,
Bjorn

> --- a/drivers/iommu/Kconfig
> +++ b/drivers/iommu/Kconfig
> @@ -308,7 +308,6 @@ config APPLE_DART
>  config ARM_SMMU
>         tristate "ARM Ltd. System MMU (SMMU) Support"
>         depends on ARM64 || ARM || (COMPILE_TEST && !GENERIC_ATOMIC64)
> -       select QCOM_SCM
>         select IOMMU_API
>         select IOMMU_IO_PGTABLE_LPAE
>         select ARM_DMA_USE_IOMMU if ARM
> @@ -438,7 +437,7 @@ config QCOM_IOMMU
>         # Note: iommu drivers cannot (yet?) be built as modules
>         bool "Qualcomm IOMMU Support"
>         depends on ARCH_QCOM || (COMPILE_TEST && !GENERIC_ATOMIC64)
> -       depends on QCOM_SCM=y
> +       select QCOM_SCM
>         select IOMMU_API
>         select IOMMU_IO_PGTABLE_LPAE
>         select ARM_DMA_USE_IOMMU
> 
> I'll see if that causes any problems for the randconfig builds.
> 
>        Arnd



More information about the ath10k mailing list