failed to run otp: -22

[Adrian Chadd]

hi!

It should be in OTP on the QCA9880 chip. Which board is this?



-adiran


On 23 April 2018 at 12:11, Arvid Picciani <aep at exys.org> wrote:
> thanks for the response. That sounds bad.
> Does ath10k load the calibration stuff different than ath9k? Ath9k works
> just fine on the same board.
> Do 9k and 10k usually share the same partition for that info or should i go
> hunting for something completely else?
> Any more reading material that might help me find out how to load that
> correctly?
>
> /b/
>
> On Mon, Apr 23, 2018 at 9:07 PM, Adrian Chadd <adrian at freebsd.org> wrote:
>>
>> Hi,
>>
>> That's designed for debugging. It means you'll have an invalid MAC
>> address and no calibration information so your NIC won't work very
>> well.
>>
>> The reason why needs to be figured out!
>>
>>
>>
>> -adrian
>>
>>
>> On 23 April 2018 at 09:56, Arvid Picciani <aep at exys.org> wrote:
>> > Hi,
>> >
>> > Is it ok to run a QCA9880 with skip_otp=1?
>> > It's working fine with skip_ota, but just want to confirm this is safe.
>> >
>> > without skip_otp, mine isn't coming up because of "failed to run otp:
>> > -22"
>> >
>> > [    9.287905] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
>> > [    9.293912] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1
>> > irq_mode 0 reset_mode 0
>> > [    9.568820] ath10k_pci 0000:00:00.0: Direct firmware load for
>> > ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
>> > [    9.579896] ath10k_pci 0000:00:00.0: Falling back to user helper
>> > [    9.737064] firmware ath10k!pre-cal-pci-0000:00:00.0.bin:
>> > firmware_loading_store: map pages failed
>> > [    9.746618] ath10k_pci 0000:00:00.0: Direct firmware load for
>> > ath10k/cal-pci-0000:00:00.0.bin failed with error -2
>> > [    9.757342] ath10k_pci 0000:00:00.0: Falling back to user helper
>> > [    9.909261] firmware ath10k!cal-pci-0000:00:00.0.bin:
>> > firmware_loading_store: map pages failed
>> > [    9.918500] ath10k_pci 0000:00:00.0: Direct firmware load for
>> > ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
>> > [    9.929582] ath10k_pci 0000:00:00.0: Falling back to user helper
>> > [   10.059370] firmware ath10k!QCA988X!hw2.0!firmware-6.bin:
>> > firmware_loading_store: map pages failed
>> > [   10.073667] ath10k_pci 0000:00:00.0: qca988x hw2.0 target
>> > 0x4100016c chip_id 0x043202ff sub 0000:0000
>> > [   10.083242] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1
>> > tracing 0 dfs 1 testmode 1
>> > [   10.096229] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00033
>> > api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 c41417d0
>> > [   10.189809] ath10k_pci 0000:00:00.0: Direct firmware load for
>> > ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
>> > [   10.200640] ath10k_pci 0000:00:00.0: Falling back to user helper
>> > [   10.271745] firmware ath10k!QCA988X!hw2.0!board-2.bin:
>> > firmware_loading_store: map pages failed
>> > [   10.299633] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A
>> > crc32 bebc7c08
>> > [   10.437761] ath10k_pci 0000:00:00.0: otp calibration failed: 2
>> > [   10.443792] ath10k_pci 0000:00:00.0: failed to run otp: -22
>> > [   10.449551] ath10k_pci 0000:00:00.0: could not init core (-22)
>> > [   10.455680] ath10k_pci 0000:00:00.0: could not probe fw (-22)
>> >
>> > _______________________________________________
>> > ath10k mailing list
>> > ath10k at lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/ath10k
>
>