QCA9984 VHT160 support
Sebastian Gottschall
s.gottschall at dd-wrt.com
Tue May 17 05:35:26 PDT 2016
this is a updated patchset which adds further corrections.
80p80 support is detected by sta flags right now.
--
Mit freundlichen Grüssen / Regards
Sebastian Gottschall / CTO
NewMedia-NET GmbH - DD-WRT
Firmensitz: Berliner Ring 101, 64625 Bensheim
Registergericht: Amtsgericht Darmstadt, HRB 25473
Geschäftsführer: Peter Steinhäuser, Christian Scheele
http://www.dd-wrt.com
email: s.gottschall at dd-wrt.com
Tel.: +496251-582650 / Fax: +496251-5826565
-------------- next part --------------
Index: drivers/net/wireless/ath/ath10k/mac.c
===================================================================
--- drivers/net/wireless/ath/ath10k/mac.c (revision 2910)
+++ drivers/net/wireless/ath/ath10k/mac.c (working copy)
@@ -539,10 +539,14 @@
case NL80211_CHAN_WIDTH_80:
phymode = MODE_11AC_VHT80;
break;
+ case NL80211_CHAN_WIDTH_160:
+ phymode = MODE_11AC_VHT160;
+ break;
+ case NL80211_CHAN_WIDTH_80P80:
+ phymode = MODE_11AC_VHT80_80;
+ break;
case NL80211_CHAN_WIDTH_5:
case NL80211_CHAN_WIDTH_10:
- case NL80211_CHAN_WIDTH_80P80:
- case NL80211_CHAN_WIDTH_160:
phymode = MODE_UNKNOWN;
break;
}
@@ -2398,6 +2402,9 @@
if (sta->bandwidth == IEEE80211_STA_RX_BW_80)
arg->peer_flags |= ar->wmi.peer_flags->bw80;
+ if (sta->bandwidth == IEEE80211_STA_RX_BW_160)
+ arg->peer_flags |= ar->wmi.peer_flags->bw160;
+
arg->peer_vht_rates.rx_max_rate =
__le16_to_cpu(vht_cap->vht_mcs.rx_highest);
arg->peer_vht_rates.rx_mcs_set =
@@ -2499,7 +2506,12 @@
!ath10k_peer_assoc_h_vht_masked(vht_mcs_mask)) {
if (sta->bandwidth == IEEE80211_STA_RX_BW_80)
phymode = MODE_11AC_VHT80;
- else if (sta->bandwidth == IEEE80211_STA_RX_BW_40)
+ else if (sta->bandwidth == IEEE80211_STA_RX_BW_160) {
+ if (sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ)
+ phymode = MODE_11AC_VHT80_80;
+ else
+ phymode = MODE_11AC_VHT160;
+ } else if (sta->bandwidth == IEEE80211_STA_RX_BW_40)
phymode = MODE_11AC_VHT40;
else if (sta->bandwidth == IEEE80211_STA_RX_BW_20)
phymode = MODE_11AC_VHT20;
@@ -4185,6 +4197,10 @@
vht_cap.cap |= val;
}
+ if (ar->vht_cap_info & IEEE80211_VHT_CAP_SHORT_GI_160) {
+ vht_cap.cap |= IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ;
+ vht_cap.cap |= IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ;
+ }
mcs_map = 0;
for (i = 0; i < 8; i++) {
@@ -6798,6 +6814,9 @@
bw = WMI_PEER_CHWIDTH_80MHZ;
break;
case IEEE80211_STA_RX_BW_160:
+ bw = WMI_PEER_CHWIDTH_160MHZ;
+ break;
+ default:
ath10k_warn(ar, "Invalid bandwidth %d in rc update for %pM\n",
sta->bandwidth, sta->addr);
bw = WMI_PEER_CHWIDTH_20MHZ;
Index: drivers/net/wireless/ath/ath10k/htt_rx.c
===================================================================
--- drivers/net/wireless/ath/ath10k/htt_rx.c (revision 2910)
+++ drivers/net/wireless/ath/ath10k/htt_rx.c (working copy)
@@ -707,6 +707,10 @@
/* 80MHZ */
case 2:
status->vht_flag |= RX_VHT_FLAG_80MHZ;
+ break;
+ case 3:
+ status->vht_flag |= RX_VHT_FLAG_160MHZ;
+ break;
}
status->flag |= RX_FLAG_VHT;
@@ -931,7 +935,7 @@
*status = *rx_status;
ath10k_dbg(ar, ATH10K_DBG_DATA,
- "rx skb %p len %u peer %pM %s %s sn %u %s%s%s%s%s %srate_idx %u vht_nss %u freq %u band %u flag 0x%llx fcs-err %i mic-err %i amsdu-more %i\n",
+ "rx skb %p len %u peer %pM %s %s sn %u %s%s%s%s%s%s%s %srate_idx %u vht_nss %u freq %u band %u flag 0x%llx fcs-err %i mic-err %i amsdu-more %i\n",
skb,
skb->len,
ieee80211_get_SA(hdr),
@@ -944,6 +948,7 @@
status->flag & RX_FLAG_VHT ? "vht" : "",
status->flag & RX_FLAG_40MHZ ? "40" : "",
status->vht_flag & RX_VHT_FLAG_80MHZ ? "80" : "",
+ status->vht_flag & RX_VHT_FLAG_160MHZ ? "160" : "",
status->flag & RX_FLAG_SHORT_GI ? "sgi " : "",
status->rate_idx,
status->vht_nss,
@@ -2193,6 +2198,8 @@
case MODE_11AC_VHT20:
case MODE_11AC_VHT40:
case MODE_11AC_VHT80:
+ case MODE_11AC_VHT160:
+ case MODE_11AC_VHT80_80:
band = NL80211_BAND_5GHZ;
break;
case MODE_11G:
Index: drivers/net/wireless/ath/ath10k/wmi-tlv.c
===================================================================
--- drivers/net/wireless/ath/ath10k/wmi-tlv.c (revision 2910)
+++ drivers/net/wireless/ath/ath10k/wmi-tlv.c (working copy)
@@ -3503,6 +3503,7 @@
.vht = WMI_TLV_PEER_VHT,
.bw80 = WMI_TLV_PEER_80MHZ,
.pmf = WMI_TLV_PEER_PMF,
+ .bw160 = WMI_TLV_PEER_160MHZ,
};
/************/
Index: drivers/net/wireless/ath/ath10k/wmi-tlv.h
===================================================================
--- drivers/net/wireless/ath/ath10k/wmi-tlv.h (revision 2910)
+++ drivers/net/wireless/ath/ath10k/wmi-tlv.h (working copy)
@@ -543,6 +543,7 @@
WMI_TLV_PEER_VHT = 0x02000000,
WMI_TLV_PEER_80MHZ = 0x04000000,
WMI_TLV_PEER_PMF = 0x08000000,
+ WMI_TLV_PEER_160MHZ = 0x20000000,
};
enum wmi_tlv_tag {
Index: drivers/net/wireless/ath/ath10k/wmi.c
===================================================================
--- drivers/net/wireless/ath/ath10k/wmi.c (revision 2910)
+++ drivers/net/wireless/ath/ath10k/wmi.c (working copy)
@@ -1569,6 +1569,7 @@
.bw80 = WMI_PEER_80MHZ,
.vht_2g = WMI_PEER_VHT_2G,
.pmf = WMI_PEER_PMF,
+ .bw160 = WMI_PEER_160MHZ,
};
static const struct wmi_peer_flags_map wmi_10x_peer_flags_map = {
@@ -1586,6 +1587,7 @@
.spatial_mux = WMI_10X_PEER_SPATIAL_MUX,
.vht = WMI_10X_PEER_VHT,
.bw80 = WMI_10X_PEER_80MHZ,
+ .bw160 = WMI_10X_PEER_160MHZ,
};
static const struct wmi_peer_flags_map wmi_10_2_peer_flags_map = {
@@ -1605,6 +1607,7 @@
.bw80 = WMI_10_2_PEER_80MHZ,
.vht_2g = WMI_10_2_PEER_VHT_2G,
.pmf = WMI_10_2_PEER_PMF,
+ .bw160 = WMI_10_2_PEER_160MHZ,
};
void ath10k_wmi_put_wmi_channel(struct wmi_channel *ch,
Index: drivers/net/wireless/ath/ath10k/wmi.h
===================================================================
--- drivers/net/wireless/ath/ath10k/wmi.h (revision 2910)
+++ drivers/net/wireless/ath/ath10k/wmi.h (working copy)
@@ -1723,8 +1723,10 @@
MODE_11AC_VHT20_2G = 11,
MODE_11AC_VHT40_2G = 12,
MODE_11AC_VHT80_2G = 13,
- MODE_UNKNOWN = 14,
- MODE_MAX = 14
+ MODE_11AC_VHT80_80 = 14,
+ MODE_11AC_VHT160 = 15,
+ MODE_UNKNOWN = 16,
+ MODE_MAX = 16
};
static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode)
@@ -1752,6 +1754,10 @@
return "11ac-vht40";
case MODE_11AC_VHT80:
return "11ac-vht80";
+ case MODE_11AC_VHT160:
+ return "11ac-vht160";
+ case MODE_11AC_VHT80_80:
+ return "11ac-vht80+80";
case MODE_11AC_VHT20_2G:
return "11ac-vht20-2g";
case MODE_11AC_VHT40_2G:
@@ -5748,6 +5754,7 @@
WMI_PEER_CHWIDTH_20MHZ = 0,
WMI_PEER_CHWIDTH_40MHZ = 1,
WMI_PEER_CHWIDTH_80MHZ = 2,
+ WMI_PEER_CHWIDTH_160MHZ = 3,
};
enum wmi_peer_param {
@@ -5838,6 +5845,7 @@
u32 bw80;
u32 vht_2g;
u32 pmf;
+ u32 bw160;
};
enum wmi_peer_flags {
@@ -5857,6 +5865,7 @@
WMI_PEER_80MHZ = 0x04000000,
WMI_PEER_VHT_2G = 0x08000000,
WMI_PEER_PMF = 0x10000000,
+ WMI_PEER_160MHZ = 0x20000000
};
enum wmi_10x_peer_flags {
@@ -5874,6 +5883,7 @@
WMI_10X_PEER_SPATIAL_MUX = 0x00200000,
WMI_10X_PEER_VHT = 0x02000000,
WMI_10X_PEER_80MHZ = 0x04000000,
+ WMI_10X_PEER_160MHZ = 0x20000000
};
enum wmi_10_2_peer_flags {
@@ -5893,6 +5903,7 @@
WMI_10_2_PEER_80MHZ = 0x04000000,
WMI_10_2_PEER_VHT_2G = 0x08000000,
WMI_10_2_PEER_PMF = 0x10000000,
+ WMI_10_2_PEER_160MHZ = 0x20000000
};
/*
More information about the ath10k
mailing list