No subject

[Alexey Ivanov]

Thank you, Mohammed Shafi,

I'll try to impement it

On 14 January 2016 at 15:26, Shajakhan, Mohammed Shafi (Mohammed
Shafi) <mohammed at qti.qualcomm.com> wrote:
> Hi Alex,
>
> not sure this thread might be useful to you
> https://lists.openwrt.org/pipermail/openwrt-devel/2015-June/033894.html
>
> if the script is part of preinit and create .bin files, it will executed before wifi comes up.
>
> regards
> shafi
> ________________________________________
> From: ath10k <ath10k-bounces at lists.infradead.org> on behalf of Alexey Ivanov <alexeyivan at gmail.com>
> Sent: 14 January 2016 16:44
> To: michal.kazior at tieto.com
> Cc: ath10k at lists.infradead.org
> Subject: Re:
>
> OK, Michał
> Thank you,
>
> I found preinit scripts. some of them do ifconfig and some
> do patching of the default mac in firmware.bin
>
> On 14 January 2016 at 11:21, Michal Kazior <michal.kazior at tieto.com> wrote:
>> On 14 January 2016 at 06:36, Alexey Ivanov <alexeyivan at gmail.com> wrote:
>>> Yes, you're right, Michał
>>> putting cal.bin to lib/firmware/ath10k helped
>>> (before I put it to lib/firmware/ath10k/QCA988X/hw2.0/)
>>>
>>> but the mac address is still 00:03:7F:00:00:00
>>>
>>> the output now is:
>>> [   11.381198] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0
>>> irq_mode 0 reset_mode 0
>>> [   11.725833] ath10k_pci 0000:00:00.0: qca988x hw2.0 target
>>> 0x4100016c chip_id 0x043202ff sub 0000:0000
>>> [   11.735226] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1
>>> tracing 0 dfs 0 testmode 1
>>> [   11.748288] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.97 api 5
>>> features no-p2p crc32 f91e34f2
>>> [   11.797377] ath10k_pci 0000:00:00.0: Direct firmware load for
>>> ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
>>> [   11.807985] ath10k_pci 0000:00:00.0: Falling back to user helper
>>> [   11.882960] firmware ath10k!QCA988X!hw2.0!board-2.bin:
>>> firmware_loading_store: map pages failed
>>> [   11.893044] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A
>>> crc32 e623b3be
>>> [   12.947352] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2
>>> cal file max-sta 128 raw 0 hwcrypto 1
>>>
>>> As I understand, after correct calibration there should be normal mac?
>>
>> Not necessarily. I think some routers have mac addresses elsewhere. If
>> you look at OpenWRT scripts you should probably find a few
>> scripts/hacks that put it in board.bin (the reason for the filename is
>> that at the time cal.bin support wasn't in ath10k yet).
>>
>>
>> Michał
>
>
>
> --
> Best regards,
> Alex Ivanov
>
> _______________________________________________
> ath10k mailing list
> ath10k at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/ath10k



-- 
Best regards,
Alex Ivanov