[PATCH 1/4] ath10k: remove supported chain mask
Janusz Dziedzic
janusz.dziedzic at tieto.com
Tue Feb 23 04:52:42 PST 2016
On 29 October 2015 at 12:01, Kalle Valo <kvalo at qca.qualcomm.com> wrote:
> Rajkumar Manoharan <rmanohar at qti.qualcomm.com> writes:
>
>> Removing supported chainmask fields as it can be always derived
>> from num_rf_chains.
>>
>> Signed-off-by: Rajkumar Manoharan <rmanohar at qti.qualcomm.com>
>
Hello,
This one break monitor mode for qca988x and 10.x firmware:
After Revert "ath10k: remove supported chain mask" - works correctly.
[ 997.415152] ath10k_pci 0000:03:00.0: mac create vdev 0 map ffff
[ 997.415154] ath10k_pci 0000:03:00.0: mac vdev create 0 (add
interface) type 4 subtype 0 bcnmode per-skb
[ 997.415156] ath10k_pci 0000:03:00.0: WMI vdev create: id 0 type 4
subtype 0 macaddr 00:00:00:00:00:00
[ 997.415157] ath10k_pci 0000:03:00.0: vdev param 0 not supported by firmware
[ 997.415161] ath10k_pci 0000:03:00.0: wmi vdev id 0x0 set param 32 value 2
[ 997.415163] ath10k_pci 0000:03:00.0: wmi vdev id 0x0 set param 1 value -1
[ 997.415254] ath10k_pci 0000:03:00.0: mac txpower 0
[ 997.415269] ath10k_pci 0000:03:00.0: wmi pdev set param 3 value 0
[ 997.415423] ath10k_pci 0000:03:00.0: firmware crashed! (uuid
d11e90aa-0f2a-433a-bcb4-eac63c6b7fdc)
[ 997.424369] ath10k_pci 0000:03:00.0: qca988x hw2.0 target
0x4100016c chip_id 0x043022ff sub 168c:3342
[ 997.424371] ath10k_pci 0000:03:00.0: kconfig debug 1 debugfs 1
tracing 1 dfs 1 testmode 0
[ 997.424498] ath10k_pci 0000:03:00.0: firmware ver 10.1.467 api 2
features wmi-10.x,has-wmi-mgmt-tx crc32 ba069298
[ 997.424501] ath10k_pci 0000:03:00.0: board_file api 1 bmi_id N/A
crc32 bebc7c08
[ 997.424503] ath10k_pci 0000:03:00.0: htt-ver 2.1 wmi-op 2 htt-op 2
cal otp max-sta 128 raw 0 hwcrypto 1
[ 997.426528] ath10k_pci 0000:03:00.0: firmware register dump:
[ 997.432176] ath10k_pci 0000:03:00.0: [00]: 0x4100016C 0x00000000
0x0097F8D2 0x00000000
[ 997.440076] ath10k_pci 0000:03:00.0: [04]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.447975] ath10k_pci 0000:03:00.0: [08]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.455875] ath10k_pci 0000:03:00.0: [12]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.463774] ath10k_pci 0000:03:00.0: [16]: 0x00000000 0x00000000
0x00000000 0x0097F8D2
[ 997.471675] ath10k_pci 0000:03:00.0: [20]: 0x00000000 0x00401930
0x00000000 0x00000000
[ 997.479574] ath10k_pci 0000:03:00.0: [24]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.487473] ath10k_pci 0000:03:00.0: [28]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.495374] ath10k_pci 0000:03:00.0: [32]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.503273] ath10k_pci 0000:03:00.0: [36]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.511172] ath10k_pci 0000:03:00.0: [40]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.519072] ath10k_pci 0000:03:00.0: [44]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.526971] ath10k_pci 0000:03:00.0: [48]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.534871] ath10k_pci 0000:03:00.0: [52]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.542772] ath10k_pci 0000:03:00.0: [56]: 0x00000000 0x00000000
0x00000000 0x00000000
[ 997.550714] ath10k_pci 0000:03:00.0: failed to set 2g txpower 0: -108
[ 997.550715] ath10k_pci 0000:03:00.0: failed to setup tx power 0: -108
[ 997.550717] ath10k_pci 0000:03:00.0: failed to recalc tx power: -108
[ 997.550718] ath10k_pci 0000:03:00.0: WMI vdev delete id 0
BR
Janusz
More information about the ath10k
mailing list