Compex WLE900N5-23

Tue May 5 19:31:16 PDT 2015

Not working as well, firmware crashed.

[   56.250000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta
128
[   56.260000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0
dfs 1 testmode 1
[   56.280000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100804: -16
[   56.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi
address for firmware address 4: -16
[   56.300000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16
[   56.400000] ieee80211 phy0: Hardware restart was requested
[   56.400000] ath10k_pci 0000:00:00.0: failed to to request monitor
vdev 1 stop: -143
[   56.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor
vdev 1 stop: -143
[   56.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[   56.630000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100800: -16
[   56.640000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[   56.750000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100800: -16
[   56.760000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[   56.870000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100800: -16

....

[  138.740000] ath10k_pci 0000:00:00.0: failed to to request monitor
vdev 1 stop: -143
[  138.750000] ath10k_pci 0000:00:00.0: failed to synchronize monitor
vdev 1 stop: -143
[  138.760000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143
[  138.970000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100800: -16
[  138.980000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16
[  139.090000] ath10k_pci 0000:00:00.0: failed to read diag value at
0x10100800: -16
[  141.380000] ath10k_pci 0000:00:00.0: device successfully recovered
[  141.750000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid
c95c836e-b4b3-40d6-bbac-d18eb4992b10)
[  141.760000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c,
0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta
128

----
Chun-Yeow

On Tue, May 5, 2015 at 7:19 PM, Michal Kazior <michal.kazior at tieto.com> wrote:
> On 5 May 2015 at 13:11, Yeoh Chun-Yeow <yeohchunyeow at gmail.com> wrote:
>> What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly?
>>
>> I ran into this error "IndexError: list index out of range" during assembly.
>
> I think the following should work:
>
>   python assemble.py 10.2-test 12 fw-from-10.2.bin otp-from-10.1.bin 5
>
> wmi-mgmt-tx = BIT(2) = 4
> no-p2p = BIT(3) = 8
>
> Hence `12` for features.
>
> If you assemble 10.2.4 wmi-op must be 5. If you use 10.2-00082 wmi-op must be 3.
>
>
> Michał
>
>
>> ---
>> Chun-Yeow
>>
>> On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior at tieto.com> wrote:
>>> On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow at gmail.com> wrote:
>>>> Yes, this is the latest firmware that I have tried:
>>>>
>>>> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw
>>>> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128
>>>>
>>>> But still the same, firmware crashed:
>>>> [  154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor
>>>> vdev 1 stop: -11
>>>> [  159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor
>>>> vdev 1 stop: -145
>>>> [  159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145
>>>> [  159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145
>>>> [  162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11
>>>> [  165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11
>>>> [  168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor
>>>> vdev 1 stop: -11
>>>> [  173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor
>>>> vdev 1 stop: -145
>>>> [  173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145
>>>> [  176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11
>>>> [  179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor
>>>> vdev 1 stop: -11
>>>> [  184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor
>>>> vdev 1 stop: -145
>>>> [  184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145
>>>> [  187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer
>>>> removal on vdev 0: -11
>>>> [  190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11
>>>> [  193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer
>>>> on vdev 0: -145
>>>> [  193.960000] ath10k_pci 0000:00:00.0: removing stale peer
>>>> 04:f0:21:0c:a5:17 from vdev_id 0
>>>> [  196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11
>>>
>>> Hmm.. Can you try to repack firmware and combine main binary from 10.2
>>> and otp from 10.1 and test that? You can use these tools:
>>>
>>>  https://gist.github.com/kazikcz/64313b9e2470660faae1
>>>  https://gist.github.com/kazikcz/c970cbf3a863ebbc4495
>>>
>>>
>>> Michał