[PATCH] wireless: ath: Fix typo 'the the' in comment

[Slark Xiao]

Replace 'the the' with 'the' in the comment.

Signed-off-by: Slark Xiao <slark_xiao at 163.com>
---
 drivers/net/wireless/ath/ath6kl/hif.h       | 2 +-
 drivers/net/wireless/ath/ath6kl/sdio.c      | 2 +-
 drivers/net/wireless/ath/ath9k/ar9003_phy.c | 2 +-
 drivers/net/wireless/ath/wcn36xx/hal.h      | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/ath/ath6kl/hif.h b/drivers/net/wireless/ath/ath6kl/hif.h
index f9d3f3a5edfe..ba16b98c872d 100644
--- a/drivers/net/wireless/ath/ath6kl/hif.h
+++ b/drivers/net/wireless/ath/ath6kl/hif.h
@@ -92,7 +92,7 @@ struct bus_request {
  *     emode - This indicates the whether the command is to be executed in a
  *             blocking or non-blocking fashion (HIF_SYNCHRONOUS/
  *             HIF_ASYNCHRONOUS). The read/write data paths in HTC have been
- *             implemented using the asynchronous mode allowing the the bus
+ *             implemented using the asynchronous mode allowing the bus
  *             driver to indicate the completion of operation through the
  *             registered callback routine. The requirement primarily comes
  *             from the contexts these operations get called from (a driver's
diff --git a/drivers/net/wireless/ath/ath6kl/sdio.c b/drivers/net/wireless/ath/ath6kl/sdio.c
index 6b51a2dceadc..8a43c48ec1cf 100644
--- a/drivers/net/wireless/ath/ath6kl/sdio.c
+++ b/drivers/net/wireless/ath/ath6kl/sdio.c
@@ -1185,7 +1185,7 @@ static int ath6kl_sdio_bmi_read(struct ath6kl *ar, u8 *buf, u32 len)
 	 *        Wait for first 4 bytes to be in FIFO
 	 *        If CONSERVATIVE_BMI_READ is enabled, also wait for
 	 *        a BMI command credit, which indicates that the ENTIRE
-	 *        response is available in the the FIFO
+	 *        response is available in the FIFO
 	 *
 	 *  CASE 3: length > 128
 	 *        Wait for the first 4 bytes to be in FIFO
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.c b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
index dc0e5ea25673..090ff0600c81 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.c
@@ -1744,7 +1744,7 @@ static void ar9003_hw_spectral_scan_config(struct ath_hw *ah,
 	REG_SET_BIT(ah, AR_PHY_RADAR_0, AR_PHY_RADAR_0_FFT_ENA);
 	REG_SET_BIT(ah, AR_PHY_SPECTRAL_SCAN, AR_PHY_SPECTRAL_SCAN_ENABLE);
 
-	/* on AR93xx and newer, count = 0 will make the the chip send
+	/* on AR93xx and newer, count = 0 will make the chip send
 	 * spectral samples endlessly. Check if this really was intended,
 	 * and fix otherwise.
 	 */
diff --git a/drivers/net/wireless/ath/wcn36xx/hal.h b/drivers/net/wireless/ath/wcn36xx/hal.h
index 874746b5993c..a1afe1f85f0e 100644
--- a/drivers/net/wireless/ath/wcn36xx/hal.h
+++ b/drivers/net/wireless/ath/wcn36xx/hal.h
@@ -4142,7 +4142,7 @@ struct wcn36xx_hal_dump_cmd_rsp_msg {
 	/* Length of the responce message */
 	u32 rsp_length;
 
-	/* FIXME: Currently considering the the responce will be less than
+	/* FIXME: Currently considering the responce will be less than
 	 * 100bytes */
 	u8 rsp_buffer[DUMPCMD_RSP_BUFFER];
 } __packed;
-- 
2.25.1