[PATCH 2/2] Simplify scanning and use correct receive channel
Olof Johansson
dev at skyshaper.net
Wed May 22 06:18:27 EDT 2013
updated patch
----
This simplifies the scanning a bit by removing the end_scan which is
not necessary. It also makes use of the channel switch command instead
of using start scan on every channel.
Reorders the 2.4Ghz channels to that the hw_values are correct
and possible to use.
Signed-off-by: Olof Johansson <dev at skyshaper.net>
---
main.c | 53 ++++++++++++++++++++++-------------------------------
smd.c | 27 +++++++++++++++++++++++++++
smd.h | 1 +
txrx.c | 4 ++--
wcn36xx.h | 2 +-
5 files changed, 53 insertions(+), 34 deletions(-)
diff --git a/main.c b/main.c
index 6eacee6..e96309d 100644
--- a/main.c
+++ b/main.c
@@ -109,16 +109,10 @@ static int wcn36xx_config(struct ieee80211_hw
*hw, u32 changed)
wcn36xx_dbg(WCN36XX_DBG_MAC, "mac config changed 0x%08x", changed);
if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
- wcn->ch = ieee80211_frequency_to_channel(hw->conf.chandef.chan->center_freq);
- wcn36xx_dbg(WCN36XX_DBG_MAC, "mac change channel %d", wcn->ch);
-
- if (wcn->is_scanning) {
- if (wcn->prev_channel) {
- wcn36xx_smd_end_scan(wcn, wcn->prev_channel);
- }
- wcn36xx_smd_start_scan(wcn, wcn->ch);
- wcn->prev_channel = wcn->ch;
- }
+ wcn->ch = hw->conf.chandef.chan->hw_value;
+ wcn->current_channel = hw->conf.chandef.chan;
+ wcn36xx_info("wcn36xx_config channel switch=%d", wcn->ch);
+ wcn36xx_smd_switch_channel_req(wcn, wcn->ch);
}
return 0;
@@ -171,19 +165,14 @@ static void wcn36xx_sw_scan_start(struct ieee80211_hw *hw)
struct wcn36xx *wcn = hw->priv;
wcn36xx_smd_init_scan(wcn);
- wcn->is_scanning = 1;
wcn36xx_smd_start_scan(wcn, wcn->ch);
- wcn->prev_channel = wcn->ch;
+ wcn->is_scanning = 1;
}
static void wcn36xx_sw_scan_complete(struct ieee80211_hw *hw)
{
struct wcn36xx *wcn = hw->priv;
-
- if (wcn->prev_channel) {
- wcn36xx_smd_end_scan(wcn, wcn->prev_channel);
- wcn->prev_channel = 0;
- }
+ wcn36xx_smd_end_scan(wcn, wcn->ch);
wcn36xx_smd_finish_scan(wcn);
wcn->is_scanning = 0;
}
@@ -348,21 +337,23 @@ static struct ieee80211_hw *wcn36xx_alloc_hw(void)
.max_power = 25, \
}
+/* The wcn firmware expects channel values to matching
+ * their mnemonic values. So use these for .hw_value. */
static struct ieee80211_channel wcn_2ghz_channels[] = {
- CHAN2G(2412, 0), /* Channel 1 */
- CHAN2G(2417, 1), /* Channel 2 */
- CHAN2G(2422, 2), /* Channel 3 */
- CHAN2G(2427, 3), /* Channel 4 */
- CHAN2G(2432, 4), /* Channel 5 */
- CHAN2G(2437, 5), /* Channel 6 */
- CHAN2G(2442, 6), /* Channel 7 */
- CHAN2G(2447, 7), /* Channel 8 */
- CHAN2G(2452, 8), /* Channel 9 */
- CHAN2G(2457, 9), /* Channel 10 */
- CHAN2G(2462, 10), /* Channel 11 */
- CHAN2G(2467, 11), /* Channel 12 */
- CHAN2G(2472, 12), /* Channel 13 */
- CHAN2G(2484, 13) /* Channel 14 */
+ CHAN2G(2412, 1), /* Channel 1 */
+ CHAN2G(2417, 2), /* Channel 2 */
+ CHAN2G(2422, 3), /* Channel 3 */
+ CHAN2G(2427, 4), /* Channel 4 */
+ CHAN2G(2432, 5), /* Channel 5 */
+ CHAN2G(2437, 6), /* Channel 6 */
+ CHAN2G(2442, 7), /* Channel 7 */
+ CHAN2G(2447, 8), /* Channel 8 */
+ CHAN2G(2452, 9), /* Channel 9 */
+ CHAN2G(2457, 10), /* Channel 10 */
+ CHAN2G(2462, 11), /* Channel 11 */
+ CHAN2G(2467, 12), /* Channel 12 */
+ CHAN2G(2472, 13), /* Channel 13 */
+ CHAN2G(2484, 14) /* Channel 14 */
};
diff --git a/smd.c b/smd.c
index 19ff583..28d8ec8 100644
--- a/smd.c
+++ b/smd.c
@@ -233,6 +233,30 @@ int wcn36xx_smd_finish_scan(struct wcn36xx *wcn)
return wcn36xx_smd_send_and_wait(wcn, msg_body.header.len);
}
+
+int wcn36xx_smd_switch_channel_req(struct wcn36xx *wcn, int ch)
+{
+ struct wcn36xx_hal_switch_channel_req_msg msg_body;
+
+ INIT_HAL_MSG(msg_body, WCN36XX_HAL_CH_SWITCH_REQ);
+
+ msg_body.channel_number = (u8)ch;
+ msg_body.tx_mgmt_power = 0xbf;
+ msg_body.max_tx_power = 0xbf;
+ memcpy(msg_body.self_sta_mac_addr, wcn->addresses[0].addr, ETH_ALEN);
+
+ PREPARE_HAL_BUF(wcn->smd_buf, msg_body);
+
+ return wcn36xx_smd_send_and_wait(wcn, msg_body.header.len);
+}
+
+void wcn36xx_smd_switch_channel_rsp(void *buf, size_t len)
+{
+ struct wcn36xx_hal_switch_channel_rsp_msg *rsp;
+ rsp = (struct wcn36xx_hal_switch_channel_rsp_msg*)buf;
+ wcn36xx_info("channel switched to: %d, status: %d",
rsp->channel_number, rsp->status);
+}
+
int wcn36xx_smd_update_scan_params(struct wcn36xx *wcn){
struct wcn36xx_hal_update_scan_params_req msg_body;
@@ -564,6 +588,9 @@ static void wcn36xx_smd_rsp_process(struct wcn36xx
*wcn, void *buf, size_t len)
case WCN36XX_HAL_UPDATE_SCAN_PARAM_RSP:
wcn36xx_smd_update_scan_params_rsp(buf, len);
break;
+ case WCN36XX_HAL_CH_SWITCH_RSP:
+ wcn36xx_smd_switch_channel_rsp(buf,len);
+ break;
default:
wcn36xx_error("SMD_EVENT (%d) not supported", msg_header->msg_type);
}
diff --git a/smd.h b/smd.h
index ad5af54..3b7d6db 100644
--- a/smd.h
+++ b/smd.h
@@ -62,6 +62,7 @@ int wcn36xx_smd_config_bss(struct wcn36xx *wcn, bool
sta_mode, u8 *bssid, u8 upd
int wcn36xx_smd_delete_bss(struct wcn36xx *wcn);
int wcn36xx_smd_config_sta(struct wcn36xx *wcn, u8 *bssid, u16
ass_id, u8 *sta_mac);
int wcn36xx_smd_send_beacon(struct wcn36xx *wcn, struct sk_buff
*skb_beacon, u16 tim_off, u16 p2p_off);
+int wcn36xx_smd_switch_channel_req(struct wcn36xx *wcn, int ch);
// WCN36XX configuration parameters
struct wcn36xx_fw_cfg {
diff --git a/txrx.c b/txrx.c
index f199f4b..873cc6a 100644
--- a/txrx.c
+++ b/txrx.c
@@ -31,8 +31,8 @@ int wcn36xx_rx_skb(struct wcn36xx *wcn, struct sk_buff *skb)
skb_trim(skb2, bd->pdu.mpdu_len);
status.mactime = 10;
- status.band = IEEE80211_BAND_2GHZ;
- status.freq = ieee80211_channel_to_frequency(bd->rx_ch, status.band);
+ status.freq = wcn->current_channel->center_freq;
+ status.band = wcn->current_channel->band;
status.signal = 1;
status.antenna = 1;
status.rate_idx = 1;
diff --git a/wcn36xx.h b/wcn36xx.h
index 2860c10..bebe47b 100644
--- a/wcn36xx.h
+++ b/wcn36xx.h
@@ -97,6 +97,7 @@ struct wcn36xx {
const struct firmware *nv;
struct mac_address addresses[2];
int ch;
+ struct ieee80211_channel *current_channel;
u8 fw_revision;
u8 fw_version;
@@ -126,7 +127,6 @@ struct wcn36xx {
//Scanning
int is_scanning;
- int prev_channel;
// DXE chanels
struct wcn36xx_dxe_ch dxe_tx_l_ch; // TX low channel
--
1.8.2.2
More information about the wcn36xx
mailing list