<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
<p>Hello. I have just run-tested the patch from your tree on actual
hardware - the web GUI works fine, as do both internet and
wireless interfaces.</p>
<p>An investigation into the art partition has shown that there are
four sequential MAC addresses stored in memory.</p>
<p>The first and the third are back-to-back, addresses 0x0000 and
0x0006 respectively.</p>
<p>The second one is located at 0x1002, and the fourth one is at
0x5006. I have no explanation for why it is like that.</p>
<p>To answer your question - it's not an exact match, but it's close
to that.</p>
<p><br>
</p>
<p>P.S. Thank you for catching the v5/v6 difference - or lack of
thereof, rather.<br>
</p>
<div class="moz-cite-prefix">On 2020-05-24 7:45 a.m.,
<a class="moz-txt-link-abbreviated" href="mailto:mail@adrianschmutzler.de">mail@adrianschmutzler.de</a> wrote:<br>
</div>
<blockquote type="cite"
cite="mid:007001d631c0$e40282e0$ac0788a0$@adrianschmutzler.de">
<pre class="moz-quote-pre" wrap="">Hi,
</pre>
<blockquote type="cite">
<pre class="moz-quote-pre" wrap="">-----Original Message-----
From: openwrt-devel [<a class="moz-txt-link-freetext" href="mailto:openwrt-devel-bounces@lists.openwrt.org">mailto:openwrt-devel-bounces@lists.openwrt.org</a>]
On Behalf Of <a class="moz-txt-link-abbreviated" href="mailto:admin@kryma.net">admin@kryma.net</a>
Sent: Freitag, 27. März 2020 04:33
To: <a class="moz-txt-link-abbreviated" href="mailto:openwrt-devel@lists.openwrt.org">openwrt-devel@lists.openwrt.org</a>
Cc: Pavel Balan <a class="moz-txt-link-rfc2396E" href="mailto:admin@kryma.net"><admin@kryma.net></a>
Subject: [OpenWrt-Devel] [PATCH v6] ath79: add support for COMFAST CF-
E130N v2
From: Pavel Balan <a class="moz-txt-link-rfc2396E" href="mailto:admin@kryma.net"><admin@kryma.net></a>
This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless
CPE with a single Ethernet port and a 802.11bgn radio.
Specifications:
- QCA9531 SoC
- 1x 10/100 Mbps Ethernet with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 5 dBi built-in antenna
- POWER/LAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI.
The U-boot bootloader also contains a backup TFTP client to upload the
firmware from. Upon boot, it checks its ethernet network for the IP
192.168.1.10. Host a TFTP server and provide the image to be flashed as file
firmware_auto.bin.
Signed-off-by: Pavel Balan <a class="moz-txt-link-rfc2396E" href="mailto:admin@kryma.net"><admin@kryma.net></a>
---
Run-tested on hardware.
Changes since v5:
Made partition@7e0000 read-only.
Changed IMAGE_SIZE to 7936k.
</pre>
</blockquote>
<pre class="moz-quote-pre" wrap="">
it looks like you have actually sent the v5 version of your patch again, as the v6-changes you report are not included. Anyway, I've added these (and a few others) myself and pushed the result to my staging tree here:
<a class="moz-txt-link-freetext" href="https://git.openwrt.org/?p=openwrt/staging/adrian.git;a=shortlog;h=refs/heads/staging">https://git.openwrt.org/?p=openwrt/staging/adrian.git;a=shortlog;h=refs/heads/staging</a>
Please run this on your device and check whether everything is okay, so I can merge this.
Despite, I'd be interested whether the MAC address from calibration data (art 0x1002) is actually the same as art 0x0, so we can drop mtd-mac-address from wmac.
Best
Adrian
</pre>
<blockquote type="cite">
<pre class="moz-quote-pre" wrap="">
---
.../ath79/dts/qca9531_comfast_cf-e130n-v2.dts | 150
++++++++++++++++++
.../generic/base-files/etc/board.d/01_leds | 8 +
.../generic/base-files/etc/board.d/02_network | 1 +
target/linux/ath79/image/generic.mk | 10 ++
4 files changed, 169 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e130n-
v2.dts
diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
new file mode 100644
index 0000000000..dc1e037307
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+ compatible = "comfast,cf-e130n-v2", "qca,qca9531";
+ model = "COMFAST CF-E130N v2";
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_rssihigh;
+ led-failsafe = &led_rssihigh;
+ led-upgrade = &led_rssihigh;
+ label-mac-device = ð1;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+
+ wlan {
+ label = "cf-e130n-v2:green:wlan";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ lan {
+ label = "cf-e130n-v2:green:lan";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ unused {
+ label = "cf-e130n-v2:green:unused";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ rssilow {
+ label = "cf-e130n-v2:red:rssilow";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumlow {
+ label = "cf-e130n-v2:red:rssimediumlow";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumhigh {
+ label = "cf-e130n-v2:green:rssimediumhigh";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_rssihigh: rssihigh {
+ label = "cf-e130n-v2:green:rssihigh";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x010000>;
+ read-only;
+ };
+
+ art: partition@10000 {
+ label = "art";
+ reg = <0x010000 0x010000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x020000 0x7c0000>;
+ };
+
+ partition@7e0000 {
+ compatible = "denx,uimage";
+ label = "configs";
+ reg = <0x7e0000 0x010000>;
+ };
+
+ partition@7f0000 {
+ label = "nvram";
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+
+};
+
+ð0 {
+ compatible = "syscon", "simple-mfd";
+};
+
+ð1 {
+ status = "okay";
+
+ phy-handle = <&swphy0>;
+
+ mtd-mac-address = <&art 0x0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index fbb0d0ea03..3046d34605 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -47,6 +47,14 @@ comfast,cf-e120a-v3)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH"
"$boardname:green:rssihigh" "wlan0" "76" "100"
;;
+comfast,cf-e130n-v2)
+ ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow"
"wlan0" "1" "100"
+ ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW"
"$boardname:red:rssimediumlow" "wlan0" "26" "100"
+ ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
+ ucidef_set_led_rssi "rssihigh" "RSSIHIGH"
"$boardname:green:rssihigh" "wlan0" "76" "100"
+ ;;
comfast,cf-e313ac)
ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan"
"switch0" "0x02"
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan"
"eth1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 10ca213e70..b1ecc066fd 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ ath79_setup_interfaces()
alfa-network,ap121f|\
aruba,ap-105|\
avm,fritz300e|\
+ comfast,cf-e130n-v2|\
devolo,dvl1200i|\
devolo,dvl1750c|\
devolo,dvl1750i|\
diff --git a/target/linux/ath79/image/generic.mk
b/target/linux/ath79/image/generic.mk
index 70631c20d0..256481ece3 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -258,6 +258,16 @@ define Device/comfast_cf-e120a-v3 endef
TARGET_DEVICES += comfast_cf-e120a-v3
+define Device/comfast_cf-e130n-v2
+ ATH_SOC := qca9531
+ DEVICE_VENDOR := COMFAST
+ DEVICE_MODEL := CF-E130N
+ DEVICE_VARIANT := v2
+ DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
+ IMAGE_SIZE := 8000k
+endef
+TARGET_DEVICES += comfast_cf-e130n-v2
+
define Device/comfast_cf-e313ac
ATH_SOC := qca9531
DEVICE_VENDOR := COMFAST
--
2.17.1
_______________________________________________
openwrt-devel mailing list
<a class="moz-txt-link-abbreviated" href="mailto:openwrt-devel@lists.openwrt.org">openwrt-devel@lists.openwrt.org</a>
<a class="moz-txt-link-freetext" href="https://lists.openwrt.org/mailman/listinfo/openwrt-devel">https://lists.openwrt.org/mailman/listinfo/openwrt-devel</a>
</pre>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
openwrt-devel mailing list
<a class="moz-txt-link-abbreviated" href="mailto:openwrt-devel@lists.openwrt.org">openwrt-devel@lists.openwrt.org</a>
<a class="moz-txt-link-freetext" href="https://lists.openwrt.org/mailman/listinfo/openwrt-devel">https://lists.openwrt.org/mailman/listinfo/openwrt-devel</a>
</pre>
</blockquote>
</blockquote>
</body>
</html>