[PATCH 2/2] mvebu: use PHY LED trigger for speed LEDs on FortiGate 50E

[INAGAKI Hiroshi]

Use <mdio>:<addr>:<speed> trigger instead of netdev(link) trigger for
Fortinet FortiGate 50E, to indicate link speed on the each phys.

1000 Mbps: Green
100 Mbps : Amber
10 Mbps  : (turn off)

Fixes: 102dc5a62506 ("mvebu: add support for Fortinet FortiGate 50E")

Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
 .../mvebu/cortexa9/base-files/etc/board.d/01_leds    |  9 ---------
 .../arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts | 12 ++++++++++++
 2 files changed, 12 insertions(+), 9 deletions(-)

diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
index bfc589e6c0..2b045d0945 100644
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
@@ -15,15 +15,6 @@ ctera,c200-v2)
 	ucidef_set_led_usbport "usb2" "USB2" "green:usb-2" "usb1-port1" "usb2-port1"
 	ucidef_set_led_usbport "usb3" "USB3" "green:usb-1" "usb1-port2" "usb2-port2"
 	;;
-fortinet,fg-50e)
-	ucidef_set_led_netdev "wan1_link" "WAN1 Link" "green:speed_wan1" "eth1" "link"
-	ucidef_set_led_netdev "wan2_link" "WAN2 Link" "green:speed_wan2" "eth2" "link"
-	ucidef_set_led_netdev "lan1_link" "LAN1 Link" "green:speed_lan1" "lan1" "link"
-	ucidef_set_led_netdev "lan2_link" "LAN2 Link" "green:speed_lan2" "lan2" "link"
-	ucidef_set_led_netdev "lan3_link" "LAN3 Link" "green:speed_lan3" "lan3" "link"
-	ucidef_set_led_netdev "lan4_link" "LAN4 Link" "green:speed_lan4" "lan4" "link"
-	ucidef_set_led_netdev "lan5_link" "LAN5 Link" "green:speed_lan5" "lan5" "link"
-	;;
 kobol,helios4)
 	ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
 	;;
diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts b/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
index 506e01f0ff..61d2da1755 100644
--- a/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
@@ -97,72 +97,84 @@
 			label = "green:speed_wan1";
 			gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "f1072004.mdio-mii:00:1Gbps";
 		};
 
 		led-7 {
 			label = "green:speed_wan2";
 			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "f1072004.mdio-mii:01:1Gbps";
 		};
 
 		led-8 {
 			label = "amber:speed_lan5";
 			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_AMBER>;
+			linux,default-trigger = "mv88e6xxx-1:00:100Mbps";
 		};
 
 		led-9 {
 			label = "green:speed_lan5";
 			gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "mv88e6xxx-1:00:1Gbps";
 		};
 
 		led-10 {
 			label = "green:speed_lan4";
 			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "mv88e6xxx-1:01:1Gbps";
 		};
 
 		led-11 {
 			label = "amber:speed_lan4";
 			gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_AMBER>;
+			linux,default-trigger = "mv88e6xxx-1:01:100Mbps";
 		};
 
 		led-12 {
 			label = "amber:speed_lan3";
 			gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_AMBER>;
+			linux,default-trigger = "mv88e6xxx-1:02:100Mbps";
 		};
 
 		led-13 {
 			label = "green:speed_lan3";
 			gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "mv88e6xxx-1:02:1Gbps";
 		};
 
 		led-14 {
 			label = "green:speed_lan1";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "mv88e6xxx-1:04:1Gbps";
 		};
 
 		led-15 {
 			label = "amber:speed_lan1";
 			gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_AMBER>;
+			linux,default-trigger = "mv88e6xxx-1:04:100Mbps";
 		};
 
 		led-16 {
 			label = "green:speed_lan2";
 			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "mv88e6xxx-1:03:1Gbps";
 		};
 
 		led-17 {
 			label = "amber:speed_lan2";
 			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
 			color = <LED_COLOR_ID_AMBER>;
+			linux,default-trigger = "mv88e6xxx-1:03:100Mbps";
 		};
 	};
 
-- 
2.39.1.windows.1