[PATCH] ath79: Add support for Ubiquiti NanoBeam AC Gen2 XC
Daniel González Cabanelas
dgcbueu at gmail.com
Wed Mar 15 08:08:05 PDT 2023
The Ubiquiti NanoBeam AC Gen2 XC (NBE-5AC-Gen2) is an outdoor 802.11ac CPE
with a waterproof casing (ultrasonically welded) and bulb shaped.
It's the same board as Gen1 but with a small antenna routed out of the SoC
and calibration data for this management radio in the "art" partition.
Hardware:
SoC: Qualcomm Atheros QCA9558
CPU: MIPS 74Kc V5.0 720 MHz, 1 core
RAM: 128 MB DDR2
Flash: 16 MB SPI-NOR, MX25L12805D
Ethernet: 1x GbE
WiFi 5 GHz: Qualcomm Atheros QCA988X
WiFi 2.4 GHz: SoC (management radio)
Internal antenna 1: 19 dBi planar (5 GHz)
Internal antenna 2: 2 dBi PCB, connected via UFL (SoC)
Buttons: 1x reset
LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
PSU: 24 Vdc passive PoE
Installation from stock airOS firmware:
- Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
https://openwrt.org/toh/ubiquiti/common
Back to stock firmware:
- Follow instructions for Ubiquiti recovery via TFTP at OpenWrt wiki.
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
---
.../dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts | 17 +++
.../ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts | 105 +----------------
.../dts/qca9558_ubnt_nanobeam-ac-xc.dtsi | 107 ++++++++++++++++++
.../generic/base-files/etc/board.d/01_leds | 1 +
.../generic/base-files/etc/board.d/02_network | 2 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
target/linux/ath79/image/generic-ubnt.mk | 10 ++
7 files changed, 141 insertions(+), 102 deletions(-)
create mode 100644 target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
create mode 100644 target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
new file mode 100644
index 0000000000..629b5bfe0a
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-gen2-xc.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree file for Ubiquiti Nanobeam NBE-5AC-Gen2 (XC)
+ */
+
+#include "qca9558_ubnt_nanobeam-ac-xc.dtsi"
+
+/ {
+ compatible = "ubnt,nanobeam-ac-gen2-xc", "ubnt,xc", "qca,qca9558";
+ model = "Ubiquiti NanoBeam AC Gen2 (XC)";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
index 91675ff615..898c249154 100644
--- a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
+++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dts
@@ -1,110 +1,11 @@
-// SPDX-License-Identifier: GPL-2.0-only
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Device Tree file for Ubiquiti Nanobeam NBE-5AC-19 (XC)
- *
- * Copyright (C) 2022 Daniel González Cabanelas <dgcbueu at gmail.com>
- * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts
*/
-
-#include "qca955x_ubnt_xc.dtsi"
+
+#include "qca9558_ubnt_nanobeam-ac-xc.dtsi"
/ {
compatible = "ubnt,nanobeam-ac-xc", "ubnt,xc", "qca,qca9558";
model = "Ubiquiti NanoBeam AC Gen1 (XC)";
-
- aliases {
- led-boot = &led_power;
- led-failsafe = &led_power;
- led-running = &led_power;
- led-upgrade = &led_power;
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "Reset button";
- linux,code = <KEY_RESTART>;
- gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- };
- };
-
- led_spi {
- compatible = "spi-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
- mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
- cs-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
- num-chipselects = <1>;
-
- led_gpio: led_gpio at 0 {
- compatible = "fairchild,74hc595";
- reg = <0>;
- gpio-controller;
- #gpio-cells = <2>;
- registers-number = <1>;
- spi-max-frequency = <10000000>;
- enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- rssi0 {
- label = "blue:rssi0";
- gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
- };
- rssi1 {
- label = "blue:rssi1";
- gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
- };
- rssi2 {
- label = "blue:rssi2";
- gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
- };
- rssi3 {
- label = "blue:rssi3";
- gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
- };
- led_power: power {
- label = "blue:power";
- gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
- default-state = "on";
- };
- };
-};
-
-&mdio0 {
- status = "okay";
-
- phy4: ethernet-phy at 4 {
- phy-mode = "sgmii";
- reg = <4>;
- at803x-override-sgmii-link-check;
- };
-};
-
-ð0 {
- status = "okay";
-
- pll-reg = <0 0x48 0>;
- pll-data = <0x03000000 0x00000101 0x00001313>;
- nvmem-cells = <&macaddr_art_0>;
- nvmem-cell-names = "mac-address";
- phy-mode = "sgmii";
- phy-handle = <&phy4>;
-};
-
-&art {
- compatible = "nvmem-cells";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_art_0: macaddr at 0 {
- reg = <0x0 0x6>;
- };
};
diff --git a/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
new file mode 100644
index 0000000000..e68ceb7f5c
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_ubnt_nanobeam-ac-xc.dtsi
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree file for Ubiquiti Nanobeam XC
+ *
+ * Copyright (C) 2022 Daniel González Cabanelas <dgcbueu at gmail.com>
+ * based on device tree from qca9558_ubnt_powerbeam-5ac-500.dts
+ */
+
+#include "qca955x_ubnt_xc.dtsi"
+
+/ {
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ num-chipselects = <1>;
+
+ led_gpio: led_gpio at 0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <10000000>;
+ enable-gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ rssi0 {
+ label = "blue:rssi0";
+ gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ rssi1 {
+ label = "blue:rssi1";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+ rssi2 {
+ label = "blue:rssi2";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+ };
+ rssi3 {
+ label = "blue:rssi3";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ led_power: power {
+ label = "blue:power";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy4: ethernet-phy at 4 {
+ phy-mode = "sgmii";
+ reg = <4>;
+ at803x-override-sgmii-link-check;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-reg = <0 0x48 0>;
+ pll-data = <0x03000000 0x00000101 0x00001313>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ phy-mode = "sgmii";
+ phy-handle = <&phy4>;
+};
+
+&art {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 5855d2a928..a91e82f5e6 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -464,6 +464,7 @@ ubnt,bullet-ac|\
ubnt,nanobeam-ac|\
ubnt,nanobeam-ac-gen2|\
ubnt,nanobeam-ac-xc|\
+ubnt,nanobeam-ac-gen2-xc|\
ubnt,nanostation-ac|\
ubnt,powerbeam-5ac-gen2)
ucidef_set_rssimon "wlan0" "200000" "1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index b20a3c13f8..f5137385c2 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -101,6 +101,7 @@ ath79_setup_interfaces()
ubnt,litebeam-ac-gen2|\
ubnt,nanobeam-ac|\
ubnt,nanobeam-ac-xc|\
+ ubnt,nanobeam-ac-gen2-xc|\
ubnt,nanostation-ac-loco|\
ubnt,nanostation-loco-m-xw|\
ubnt,powerbeam-5ac-500|\
@@ -774,6 +775,7 @@ ath79_setup_macs()
ubnt,litebeam-ac-gen2|\
ubnt,nanobeam-ac-gen2|\
ubnt,nanobeam-ac-xc|\
+ ubnt,nanobeam-ac-gen2-xc|\
ubnt,powerbeam-5ac-500|\
ubnt,powerbeam-5ac-gen2)
label_mac=$(mtd_get_mac_binary art 0x5006)
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 4db311fde0..a79781237b 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -45,6 +45,7 @@ case "$FIRMWARE" in
ubnt,nanobeam-ac|\
ubnt,nanobeam-ac-gen2|\
ubnt,nanobeam-ac-xc|\
+ ubnt,nanobeam-ac-gen2-xc|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,powerbeam-5ac-500|\
diff --git a/target/linux/ath79/image/generic-ubnt.mk b/target/linux/ath79/image/generic-ubnt.mk
index 0f70649d03..a78ccaef82 100644
--- a/target/linux/ath79/image/generic-ubnt.mk
+++ b/target/linux/ath79/image/generic-ubnt.mk
@@ -87,6 +87,16 @@ define Device/ubnt_nanobeam-ac-xc
endef
TARGET_DEVICES += ubnt_nanobeam-ac-xc
+define Device/ubnt_nanobeam-ac-gen2-xc
+ $(Device/ubnt-xc)
+ SOC := qca9558
+ DEVICE_MODEL := NanoBeam AC
+ DEVICE_VARIANT := Gen2 (XC)
+ SUPPORTED_DEVICES += ubnt,nanobeam-ac-xc
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct rssileds
+endef
+TARGET_DEVICES += ubnt_nanobeam-ac-gen2-xc
+
define Device/ubnt_nanobeam-m5-xw
$(Device/ubnt-xw)
DEVICE_MODEL := NanoBeam M5
--
2.39.2
More information about the openwrt-devel
mailing list