[PATCH 2/5] mvebu: copy 5.4 patches to 5.10
Rui Salvaterra
rsalvaterra at gmail.com
Fri Feb 19 12:43:02 EST 2021
Just a simple copy, no refresh yet.
Signed-off-by: Rui Salvaterra <rsalvaterra at gmail.com>
---
...t-for-endpoint-to-be-ready-before-tr.patch | 50 ++
...-t-rely-on-jiffies-while-holding-spi.patch | 54 ++
...ntroduce-mvneta_update_stats-routine.patch | 95 +++
...duce-page-pool-API-for-sw-buffer-man.patch | 181 ++++
...on-build_skb-in-mvneta_rx_swbm-poll-.patch | 303 +++++++
...006-net-mvneta-add-basic-XDP-support.patch | 311 +++++++
...avoid_error_message_for_optional_IRQ.patch | 31 +
...header-prefetch-in-mvneta_swbm_rx_fr.patch | 43 +
...mvneta-make-tx-buffer-array-agnostic.patch | 210 +++++
.../009-net-mvneta-add-XDP_TX-support.patch | 175 ++++
...fix-build-skb-for-bm-capable-devices.patch | 41 +
...-arm64-dts-uDPU-remove-i2c-fast-mode.patch | 31 +
...ts-uDPU-SFP-cages-support-3W-modules.patch | 34 +
...on-page_pool_recycle_direct-in-mvnet.patch | 39 +
...sallow-XDP-program-on-hardware-buffe.patch | 53 ++
...DP-support-if-sw-bm-is-used-as-fallb.patch | 67 ++
...in-link-immediately-after-enabling-t.patch | 60 ++
...7-PCI-aardvark-Improve-link-training.patch | 208 +++++
...18-PCI-aardvark-Issue-PERST-via-GPIO.patch | 123 +++
.../019-PCI-aardvark-Add-PHY-support.patch | 152 ++++
...l-armada-37xx-Set-pcie_reset_pin-to-.patch | 93 +++
...l-armada-37xx-Move-PCIe-comphy-handl.patch | 57 ++
...l-armada-37xx-Move-PCIe-max-link-spe.patch | 44 +
...-arm64-dts-add-uDPU-i2c-bus-recovery.patch | 53 ++
...-t-touch-PCIe-registers-if-no-card-c.patch | 50 ++
...add-driver-for-LinkStation-power-off.patch | 207 +++++
...-initialization-with-old-Marvell-s-A.patch | 44 +
...l-espressobin-Add-ethernet-switch-al.patch | 88 ++
...s-mcbin-singleshot-add-heartbeat-LED.patch | 65 ++
...Mangle-bootloader-s-kernel-arguments.patch | 208 +++++
...-mvebu-armada-38x-enable-libata-leds.patch | 10 +
.../patches-5.10/302-add_powertables.patch | 770 ++++++++++++++++++
...3-linksys_hardcode_nand_ecc_settings.patch | 17 +
.../patches-5.10/304-revert_i2c_delay.patch | 15 +
.../305-armada-385-rd-mtd-partitions.patch | 19 +
.../306-ARM-mvebu-385-ap-Add-partitions.patch | 35 +
...-armada-xp-linksys-mamba-broken-idle.patch | 10 +
.../308-armada-xp-linksys-mamba-wan.patch | 11 +
.../patches-5.10/309-linksys-status-led.patch | 50 ++
.../310-linksys-use-eth0-as-cpu-port.patch | 25 +
.../311-adjust-compatible-for-linksys.patch | 68 ++
...da388-clearfog-emmc-on-clearfog-base.patch | 87 ++
.../312-helios4-dts-status-led-alias.patch | 28 +
...ts-marvell-armada37xx-Add-eth0-alias.patch | 20 +
...l-armada-3720-espressobin-add-ports-.patch | 26 +
...witch-PHY-operation-mode-to-2500base.patch | 34 +
.../patches-5.10/400-find_active_root.patch | 60 ++
.../700-mvneta-tx-queue-workaround.patch | 34 +
...dicate-failure-to-enter-deeper-sleep.patch | 40 +
...-pci-mvebu-time-out-reset-on-link-up.patch | 60 ++
50 files changed, 4589 insertions(+)
create mode 100644 target/linux/mvebu/patches-5.10/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
create mode 100644 target/linux/mvebu/patches-5.10/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch
create mode 100644 target/linux/mvebu/patches-5.10/003-net-mvneta-introduce-mvneta_update_stats-routine.patch
create mode 100644 target/linux/mvebu/patches-5.10/004-net-mvneta-introduce-page-pool-API-for-sw-buffer-man.patch
create mode 100644 target/linux/mvebu/patches-5.10/005-net-mvneta-rely-on-build_skb-in-mvneta_rx_swbm-poll-.patch
create mode 100644 target/linux/mvebu/patches-5.10/006-net-mvneta-add-basic-XDP-support.patch
create mode 100644 target/linux/mvebu/patches-5.10/007-gpio-mvebu-avoid_error_message_for_optional_IRQ.patch
create mode 100644 target/linux/mvebu/patches-5.10/007-net-mvneta-move-header-prefetch-in-mvneta_swbm_rx_fr.patch
create mode 100644 target/linux/mvebu/patches-5.10/008-net-mvneta-make-tx-buffer-array-agnostic.patch
create mode 100644 target/linux/mvebu/patches-5.10/009-net-mvneta-add-XDP_TX-support.patch
create mode 100644 target/linux/mvebu/patches-5.10/010-net-mvneta-fix-build-skb-for-bm-capable-devices.patch
create mode 100644 target/linux/mvebu/patches-5.10/011-arm64-dts-uDPU-remove-i2c-fast-mode.patch
create mode 100644 target/linux/mvebu/patches-5.10/012-arm64-dts-uDPU-SFP-cages-support-3W-modules.patch
create mode 100644 target/linux/mvebu/patches-5.10/013-net-mvneta-rely-on-page_pool_recycle_direct-in-mvnet.patch
create mode 100644 target/linux/mvebu/patches-5.10/014-mvneta-driver-disallow-XDP-program-on-hardware-buffe.patch
create mode 100644 target/linux/mvebu/patches-5.10/015-net-mvneta-fix-XDP-support-if-sw-bm-is-used-as-fallb.patch
create mode 100644 target/linux/mvebu/patches-5.10/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
create mode 100644 target/linux/mvebu/patches-5.10/017-PCI-aardvark-Improve-link-training.patch
create mode 100644 target/linux/mvebu/patches-5.10/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
create mode 100644 target/linux/mvebu/patches-5.10/019-PCI-aardvark-Add-PHY-support.patch
create mode 100644 target/linux/mvebu/patches-5.10/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
create mode 100644 target/linux/mvebu/patches-5.10/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch
create mode 100644 target/linux/mvebu/patches-5.10/022-arm64-dts-marvell-armada-37xx-Move-PCIe-max-link-spe.patch
create mode 100644 target/linux/mvebu/patches-5.10/023-arm64-dts-add-uDPU-i2c-bus-recovery.patch
create mode 100644 target/linux/mvebu/patches-5.10/024-PCI-aardvark-Don-t-touch-PCIe-registers-if-no-card-c.patch
create mode 100644 target/linux/mvebu/patches-5.10/025-power-reset-add-driver-for-LinkStation-power-off.patch
create mode 100644 target/linux/mvebu/patches-5.10/026-PCI-aardvark-Fix-initialization-with-old-Marvell-s-A.patch
create mode 100644 target/linux/mvebu/patches-5.10/027-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch
create mode 100644 target/linux/mvebu/patches-5.10/028-arm64-dts-mcbin-singleshot-add-heartbeat-LED.patch
create mode 100644 target/linux/mvebu/patches-5.10/300-mvebu-Mangle-bootloader-s-kernel-arguments.patch
create mode 100644 target/linux/mvebu/patches-5.10/301-mvebu-armada-38x-enable-libata-leds.patch
create mode 100644 target/linux/mvebu/patches-5.10/302-add_powertables.patch
create mode 100644 target/linux/mvebu/patches-5.10/303-linksys_hardcode_nand_ecc_settings.patch
create mode 100644 target/linux/mvebu/patches-5.10/304-revert_i2c_delay.patch
create mode 100644 target/linux/mvebu/patches-5.10/305-armada-385-rd-mtd-partitions.patch
create mode 100644 target/linux/mvebu/patches-5.10/306-ARM-mvebu-385-ap-Add-partitions.patch
create mode 100644 target/linux/mvebu/patches-5.10/307-armada-xp-linksys-mamba-broken-idle.patch
create mode 100644 target/linux/mvebu/patches-5.10/308-armada-xp-linksys-mamba-wan.patch
create mode 100644 target/linux/mvebu/patches-5.10/309-linksys-status-led.patch
create mode 100644 target/linux/mvebu/patches-5.10/310-linksys-use-eth0-as-cpu-port.patch
create mode 100644 target/linux/mvebu/patches-5.10/311-adjust-compatible-for-linksys.patch
create mode 100644 target/linux/mvebu/patches-5.10/312-ARM-dts-armada388-clearfog-emmc-on-clearfog-base.patch
create mode 100644 target/linux/mvebu/patches-5.10/312-helios4-dts-status-led-alias.patch
create mode 100644 target/linux/mvebu/patches-5.10/314-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
create mode 100644 target/linux/mvebu/patches-5.10/315-arm64-dts-marvell-armada-3720-espressobin-add-ports-.patch
create mode 100644 target/linux/mvebu/patches-5.10/316-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch
create mode 100644 target/linux/mvebu/patches-5.10/400-find_active_root.patch
create mode 100644 target/linux/mvebu/patches-5.10/700-mvneta-tx-queue-workaround.patch
create mode 100644 target/linux/mvebu/patches-5.10/800-cpuidle-mvebu-indicate-failure-to-enter-deeper-sleep.patch
create mode 100644 target/linux/mvebu/patches-5.10/801-pci-mvebu-time-out-reset-on-link-up.patch
diff --git a/target/linux/mvebu/patches-5.10/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch b/target/linux/mvebu/patches-5.10/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
new file mode 100644
index 0000000000..95abbce002
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
@@ -0,0 +1,50 @@
+From f4c7d053d7f77cd5c1a1ba7c7ce085ddba13d1d7 Mon Sep 17 00:00:00 2001
+From: Remi Pommarel <repk at triplefau.lt>
+Date: Wed, 22 May 2019 23:33:50 +0200
+Subject: [PATCH] PCI: aardvark: Wait for endpoint to be ready before training
+ link
+
+When configuring pcie reset pin from gpio (e.g. initially set by
+u-boot) to pcie function this pin goes low for a brief moment
+asserting the PERST# signal. Thus connected device enters fundamental
+reset process and link configuration can only begin after a minimal
+100ms delay (see [1]).
+
+Because the pin configuration comes from the "default" pinctrl it is
+implicitly configured before the probe callback is called:
+
+driver_probe_device()
+ really_probe()
+ ...
+ pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
+ function and PERST# is asserted */
+ ...
+ drv->probe()
+
+[1] "PCI Express Base Specification", REV. 4.0
+ PCI Express, February 19 2014, 6.6.1 Conventional Reset
+
+Signed-off-by: Remi Pommarel <repk at triplefau.lt>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 8 ++++++++
+ 1 file changed, 8 insertions(+)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -337,6 +337,14 @@ static void advk_pcie_setup_hw(struct ad
+ reg |= PIO_CTRL_ADDR_WIN_DISABLE;
+ advk_writel(pcie, reg, PIO_CTRL);
+
++ /*
++ * PERST# signal could have been asserted by pinctrl subsystem before
++ * probe() callback has been called, making the endpoint going into
++ * fundamental reset. As required by PCI Express spec a delay for at
++ * least 100ms after such a reset before link training is needed.
++ */
++ msleep(PCI_PM_D3COLD_WAIT);
++
+ /* Start link training */
+ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+ reg |= PCIE_CORE_LINK_TRAINING;
diff --git a/target/linux/mvebu/patches-5.10/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch b/target/linux/mvebu/patches-5.10/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch
new file mode 100644
index 0000000000..db4afd22a2
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch
@@ -0,0 +1,54 @@
+From 7fbcb5da811be7d47468417c7795405058abb3da Mon Sep 17 00:00:00 2001
+From: Remi Pommarel <repk at triplefau.lt>
+Date: Fri, 27 Sep 2019 10:55:02 +0200
+Subject: [PATCH] PCI: aardvark: Don't rely on jiffies while holding spinlock
+
+advk_pcie_wait_pio() can be called while holding a spinlock (from
+pci_bus_read_config_dword()), then depends on jiffies in order to
+timeout while polling on PIO state registers. In the case the PIO
+transaction failed, the timeout will never happen and will also cause
+the cpu to stall.
+
+This decrements a variable and wait instead of using jiffies.
+
+Signed-off-by: Remi Pommarel <repk at triplefau.lt>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Reviewed-by: Andrew Murray <andrew.murray at arm.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 10 +++++-----
+ 1 file changed, 5 insertions(+), 5 deletions(-)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -175,7 +175,8 @@
+ (PCIE_CONF_BUS(bus) | PCIE_CONF_DEV(PCI_SLOT(devfn)) | \
+ PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where))
+
+-#define PIO_TIMEOUT_MS 1
++#define PIO_RETRY_CNT 500
++#define PIO_RETRY_DELAY 2 /* 2 us*/
+
+ #define LINK_WAIT_MAX_RETRIES 10
+ #define LINK_WAIT_USLEEP_MIN 90000
+@@ -400,17 +401,16 @@ static void advk_pcie_check_pio_status(s
+ static int advk_pcie_wait_pio(struct advk_pcie *pcie)
+ {
+ struct device *dev = &pcie->pdev->dev;
+- unsigned long timeout;
++ int i;
+
+- timeout = jiffies + msecs_to_jiffies(PIO_TIMEOUT_MS);
+-
+- while (time_before(jiffies, timeout)) {
++ for (i = 0; i < PIO_RETRY_CNT; i++) {
+ u32 start, isr;
+
+ start = advk_readl(pcie, PIO_START);
+ isr = advk_readl(pcie, PIO_ISR);
+ if (!start && isr)
+ return 0;
++ udelay(PIO_RETRY_DELAY);
+ }
+
+ dev_err(dev, "config read/write timed out\n");
diff --git a/target/linux/mvebu/patches-5.10/003-net-mvneta-introduce-mvneta_update_stats-routine.patch b/target/linux/mvebu/patches-5.10/003-net-mvneta-introduce-mvneta_update_stats-routine.patch
new file mode 100644
index 0000000000..f6ce6163cf
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/003-net-mvneta-introduce-mvneta_update_stats-routine.patch
@@ -0,0 +1,95 @@
+From ff519e2acd463bff6c5bb4e8d7ed350c9bae885b Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:21 +0200
+Subject: [PATCH 1/7] net: mvneta: introduce mvneta_update_stats routine
+
+Introduce mvneta_update_stats routine to collect {rx/tx} statistics
+(packets and bytes). This is a preliminary patch to add XDP support to
+mvneta driver
+
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 43 ++++++++++++++-------------
+ 1 file changed, 22 insertions(+), 21 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -1913,6 +1913,23 @@ static void mvneta_rxq_drop_pkts(struct
+ }
+ }
+
++static void
++mvneta_update_stats(struct mvneta_port *pp, u32 pkts,
++ u32 len, bool tx)
++{
++ struct mvneta_pcpu_stats *stats = this_cpu_ptr(pp->stats);
++
++ u64_stats_update_begin(&stats->syncp);
++ if (tx) {
++ stats->tx_packets += pkts;
++ stats->tx_bytes += len;
++ } else {
++ stats->rx_packets += pkts;
++ stats->rx_bytes += len;
++ }
++ u64_stats_update_end(&stats->syncp);
++}
++
+ static inline
+ int mvneta_rx_refill_queue(struct mvneta_port *pp, struct mvneta_rx_queue *rxq)
+ {
+@@ -2093,14 +2110,8 @@ static int mvneta_rx_swbm(struct napi_st
+ rxq->left_size = 0;
+ }
+
+- if (rcvd_pkts) {
+- struct mvneta_pcpu_stats *stats = this_cpu_ptr(pp->stats);
+-
+- u64_stats_update_begin(&stats->syncp);
+- stats->rx_packets += rcvd_pkts;
+- stats->rx_bytes += rcvd_bytes;
+- u64_stats_update_end(&stats->syncp);
+- }
++ if (rcvd_pkts)
++ mvneta_update_stats(pp, rcvd_pkts, rcvd_bytes, false);
+
+ /* return some buffers to hardware queue, one at a time is too slow */
+ refill = mvneta_rx_refill_queue(pp, rxq);
+@@ -2223,14 +2234,8 @@ err_drop_frame:
+ napi_gro_receive(napi, skb);
+ }
+
+- if (rcvd_pkts) {
+- struct mvneta_pcpu_stats *stats = this_cpu_ptr(pp->stats);
+-
+- u64_stats_update_begin(&stats->syncp);
+- stats->rx_packets += rcvd_pkts;
+- stats->rx_bytes += rcvd_bytes;
+- u64_stats_update_end(&stats->syncp);
+- }
++ if (rcvd_pkts)
++ mvneta_update_stats(pp, rcvd_pkts, rcvd_bytes, false);
+
+ /* Update rxq management counters */
+ mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done);
+@@ -2476,7 +2481,6 @@ static netdev_tx_t mvneta_tx(struct sk_b
+
+ out:
+ if (frags > 0) {
+- struct mvneta_pcpu_stats *stats = this_cpu_ptr(pp->stats);
+ struct netdev_queue *nq = netdev_get_tx_queue(dev, txq_id);
+
+ netdev_tx_sent_queue(nq, len);
+@@ -2491,10 +2495,7 @@ out:
+ else
+ txq->pending += frags;
+
+- u64_stats_update_begin(&stats->syncp);
+- stats->tx_packets++;
+- stats->tx_bytes += len;
+- u64_stats_update_end(&stats->syncp);
++ mvneta_update_stats(pp, 1, len, true);
+ } else {
+ dev->stats.tx_dropped++;
+ dev_kfree_skb_any(skb);
diff --git a/target/linux/mvebu/patches-5.10/004-net-mvneta-introduce-page-pool-API-for-sw-buffer-man.patch b/target/linux/mvebu/patches-5.10/004-net-mvneta-introduce-page-pool-API-for-sw-buffer-man.patch
new file mode 100644
index 0000000000..fbcae20f74
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/004-net-mvneta-introduce-page-pool-API-for-sw-buffer-man.patch
@@ -0,0 +1,181 @@
+From 568a3fa24a95476d40afe3f8616bafb543bc4182 Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:22 +0200
+Subject: [PATCH 2/7] net: mvneta: introduce page pool API for sw buffer
+ manager
+
+Use the page_pool api for allocations and DMA handling instead of
+__dev_alloc_page()/dma_map_page() and free_page()/dma_unmap_page().
+Pages are unmapped using page_pool_release_page before packets
+go into the network stack.
+
+The page_pool API offers buffer recycling capabilities for XDP but
+allocates one page per packet, unless the driver splits and manages
+the allocated page.
+This is a preliminary patch to add XDP support to mvneta driver
+
+Signed-off-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
+Signed-off-by: Jesper Dangaard Brouer <brouer at redhat.com>
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/Kconfig | 1 +
+ drivers/net/ethernet/marvell/mvneta.c | 83 +++++++++++++++++++++------
+ 2 files changed, 65 insertions(+), 19 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/Kconfig
++++ b/drivers/net/ethernet/marvell/Kconfig
+@@ -61,6 +61,7 @@ config MVNETA
+ depends on ARCH_MVEBU || COMPILE_TEST
+ select MVMDIO
+ select PHYLINK
++ select PAGE_POOL
+ ---help---
+ This driver supports the network interface units in the
+ Marvell ARMADA XP, ARMADA 370, ARMADA 38x and
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -37,6 +37,7 @@
+ #include <net/ip.h>
+ #include <net/ipv6.h>
+ #include <net/tso.h>
++#include <net/page_pool.h>
+
+ /* Registers */
+ #define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2))
+@@ -607,6 +608,10 @@ struct mvneta_rx_queue {
+ u32 pkts_coal;
+ u32 time_coal;
+
++ /* page_pool */
++ struct page_pool *page_pool;
++ struct xdp_rxq_info xdp_rxq;
++
+ /* Virtual address of the RX buffer */
+ void **buf_virt_addr;
+
+@@ -1825,23 +1830,21 @@ static int mvneta_rx_refill(struct mvnet
+ struct mvneta_rx_queue *rxq,
+ gfp_t gfp_mask)
+ {
++ enum dma_data_direction dma_dir;
+ dma_addr_t phys_addr;
+ struct page *page;
+
+- page = __dev_alloc_page(gfp_mask);
++ page = page_pool_alloc_pages(rxq->page_pool,
++ gfp_mask | __GFP_NOWARN);
+ if (!page)
+ return -ENOMEM;
+
+- /* map page for use */
+- phys_addr = dma_map_page(pp->dev->dev.parent, page, 0, PAGE_SIZE,
+- DMA_FROM_DEVICE);
+- if (unlikely(dma_mapping_error(pp->dev->dev.parent, phys_addr))) {
+- __free_page(page);
+- return -ENOMEM;
+- }
+-
+- phys_addr += pp->rx_offset_correction;
++ phys_addr = page_pool_get_dma_addr(page) + pp->rx_offset_correction;
++ dma_dir = page_pool_get_dma_dir(rxq->page_pool);
++ dma_sync_single_for_device(pp->dev->dev.parent, phys_addr,
++ PAGE_SIZE, dma_dir);
+ mvneta_rx_desc_fill(rx_desc, phys_addr, page, rxq);
++
+ return 0;
+ }
+
+@@ -1907,10 +1910,12 @@ static void mvneta_rxq_drop_pkts(struct
+ if (!data || !(rx_desc->buf_phys_addr))
+ continue;
+
+- dma_unmap_page(pp->dev->dev.parent, rx_desc->buf_phys_addr,
+- PAGE_SIZE, DMA_FROM_DEVICE);
+- __free_page(data);
++ page_pool_put_page(rxq->page_pool, data, false);
+ }
++ if (xdp_rxq_info_is_reg(&rxq->xdp_rxq))
++ xdp_rxq_info_unreg(&rxq->xdp_rxq);
++ page_pool_destroy(rxq->page_pool);
++ rxq->page_pool = NULL;
+ }
+
+ static void
+@@ -2047,8 +2052,7 @@ static int mvneta_rx_swbm(struct napi_st
+ skb_add_rx_frag(rxq->skb, frag_num, page,
+ frag_offset, frag_size,
+ PAGE_SIZE);
+- dma_unmap_page(dev->dev.parent, phys_addr,
+- PAGE_SIZE, DMA_FROM_DEVICE);
++ page_pool_release_page(rxq->page_pool, page);
+ rxq->left_size -= frag_size;
+ }
+ } else {
+@@ -2078,9 +2082,7 @@ static int mvneta_rx_swbm(struct napi_st
+ frag_offset, frag_size,
+ PAGE_SIZE);
+
+- dma_unmap_page(dev->dev.parent, phys_addr,
+- PAGE_SIZE, DMA_FROM_DEVICE);
+-
++ page_pool_release_page(rxq->page_pool, page);
+ rxq->left_size -= frag_size;
+ }
+ } /* Middle or Last descriptor */
+@@ -2847,11 +2849,54 @@ static int mvneta_poll(struct napi_struc
+ return rx_done;
+ }
+
++static int mvneta_create_page_pool(struct mvneta_port *pp,
++ struct mvneta_rx_queue *rxq, int size)
++{
++ struct page_pool_params pp_params = {
++ .order = 0,
++ .flags = PP_FLAG_DMA_MAP,
++ .pool_size = size,
++ .nid = cpu_to_node(0),
++ .dev = pp->dev->dev.parent,
++ .dma_dir = DMA_FROM_DEVICE,
++ };
++ int err;
++
++ rxq->page_pool = page_pool_create(&pp_params);
++ if (IS_ERR(rxq->page_pool)) {
++ err = PTR_ERR(rxq->page_pool);
++ rxq->page_pool = NULL;
++ return err;
++ }
++
++ err = xdp_rxq_info_reg(&rxq->xdp_rxq, pp->dev, rxq->id);
++ if (err < 0)
++ goto err_free_pp;
++
++ err = xdp_rxq_info_reg_mem_model(&rxq->xdp_rxq, MEM_TYPE_PAGE_POOL,
++ rxq->page_pool);
++ if (err)
++ goto err_unregister_rxq;
++
++ return 0;
++
++err_unregister_rxq:
++ xdp_rxq_info_unreg(&rxq->xdp_rxq);
++err_free_pp:
++ page_pool_destroy(rxq->page_pool);
++ rxq->page_pool = NULL;
++ return err;
++}
++
+ /* Handle rxq fill: allocates rxq skbs; called when initializing a port */
+ static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
+ int num)
+ {
+- int i;
++ int i, err;
++
++ err = mvneta_create_page_pool(pp, rxq, num);
++ if (err < 0)
++ return err;
+
+ for (i = 0; i < num; i++) {
+ memset(rxq->descs + i, 0, sizeof(struct mvneta_rx_desc));
diff --git a/target/linux/mvebu/patches-5.10/005-net-mvneta-rely-on-build_skb-in-mvneta_rx_swbm-poll-.patch b/target/linux/mvebu/patches-5.10/005-net-mvneta-rely-on-build_skb-in-mvneta_rx_swbm-poll-.patch
new file mode 100644
index 0000000000..9038ca8ca8
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/005-net-mvneta-rely-on-build_skb-in-mvneta_rx_swbm-poll-.patch
@@ -0,0 +1,303 @@
+From 8dc9a0888f4c8e27b25e48ff1b4bc2b3a845cc2d Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:23 +0200
+Subject: [PATCH 3/7] net: mvneta: rely on build_skb in mvneta_rx_swbm poll
+ routine
+
+Refactor mvneta_rx_swbm code introducing mvneta_swbm_rx_frame and
+mvneta_swbm_add_rx_fragment routines. Rely on build_skb in oreder to
+allocate skb since the previous patch introduced buffer recycling using
+the page_pool API.
+This patch fixes even an issue in the original driver where dma buffers
+are accessed before dma sync.
+mvneta driver can run on not cache coherent devices so it is
+necessary to sync DMA buffers before sending them to the device
+in order to avoid memory corruptions. Running perf analysis we can
+see a performance cost associated with this DMA-sync (anyway it is
+already there in the original driver code). In follow up patches we
+will add more logic to reduce DMA-sync as much as possible.
+
+Signed-off-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
+Signed-off-by: Jesper Dangaard Brouer <brouer at redhat.com>
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 185 +++++++++++++-------------
+ 1 file changed, 95 insertions(+), 90 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -325,6 +325,11 @@
+ ETH_HLEN + ETH_FCS_LEN, \
+ cache_line_size())
+
++#define MVNETA_SKB_PAD (SKB_DATA_ALIGN(sizeof(struct skb_shared_info) + \
++ NET_SKB_PAD))
++#define MVNETA_SKB_SIZE(len) (SKB_DATA_ALIGN(len) + MVNETA_SKB_PAD)
++#define MVNETA_MAX_RX_BUF_SIZE (PAGE_SIZE - MVNETA_SKB_PAD)
++
+ #define IS_TSO_HEADER(txq, addr) \
+ ((addr >= txq->tso_hdrs_phys) && \
+ (addr < txq->tso_hdrs_phys + txq->size * TSO_HEADER_SIZE))
+@@ -650,7 +655,6 @@ static int txq_number = 8;
+ static int rxq_def;
+
+ static int rx_copybreak __read_mostly = 256;
+-static int rx_header_size __read_mostly = 128;
+
+ /* HW BM need that each port be identify by a unique ID */
+ static int global_port_id;
+@@ -1842,7 +1846,7 @@ static int mvneta_rx_refill(struct mvnet
+ phys_addr = page_pool_get_dma_addr(page) + pp->rx_offset_correction;
+ dma_dir = page_pool_get_dma_dir(rxq->page_pool);
+ dma_sync_single_for_device(pp->dev->dev.parent, phys_addr,
+- PAGE_SIZE, dma_dir);
++ MVNETA_MAX_RX_BUF_SIZE, dma_dir);
+ mvneta_rx_desc_fill(rx_desc, phys_addr, page, rxq);
+
+ return 0;
+@@ -1960,30 +1964,102 @@ int mvneta_rx_refill_queue(struct mvneta
+ return i;
+ }
+
++static int
++mvneta_swbm_rx_frame(struct mvneta_port *pp,
++ struct mvneta_rx_desc *rx_desc,
++ struct mvneta_rx_queue *rxq,
++ struct page *page)
++{
++ unsigned char *data = page_address(page);
++ int data_len = -MVNETA_MH_SIZE, len;
++ struct net_device *dev = pp->dev;
++ enum dma_data_direction dma_dir;
++
++ if (MVNETA_SKB_SIZE(rx_desc->data_size) > PAGE_SIZE) {
++ len = MVNETA_MAX_RX_BUF_SIZE;
++ data_len += len;
++ } else {
++ len = rx_desc->data_size;
++ data_len += len - ETH_FCS_LEN;
++ }
++
++ dma_dir = page_pool_get_dma_dir(rxq->page_pool);
++ dma_sync_single_for_cpu(dev->dev.parent,
++ rx_desc->buf_phys_addr,
++ len, dma_dir);
++
++ rxq->skb = build_skb(data, PAGE_SIZE);
++ if (unlikely(!rxq->skb)) {
++ netdev_err(dev,
++ "Can't allocate skb on queue %d\n",
++ rxq->id);
++ dev->stats.rx_dropped++;
++ rxq->skb_alloc_err++;
++ return -ENOMEM;
++ }
++ page_pool_release_page(rxq->page_pool, page);
++
++ skb_reserve(rxq->skb, MVNETA_MH_SIZE + NET_SKB_PAD);
++ skb_put(rxq->skb, data_len);
++ mvneta_rx_csum(pp, rx_desc->status, rxq->skb);
++
++ rxq->left_size = rx_desc->data_size - len;
++ rx_desc->buf_phys_addr = 0;
++
++ return 0;
++}
++
++static void
++mvneta_swbm_add_rx_fragment(struct mvneta_port *pp,
++ struct mvneta_rx_desc *rx_desc,
++ struct mvneta_rx_queue *rxq,
++ struct page *page)
++{
++ struct net_device *dev = pp->dev;
++ enum dma_data_direction dma_dir;
++ int data_len, len;
++
++ if (rxq->left_size > MVNETA_MAX_RX_BUF_SIZE) {
++ len = MVNETA_MAX_RX_BUF_SIZE;
++ data_len = len;
++ } else {
++ len = rxq->left_size;
++ data_len = len - ETH_FCS_LEN;
++ }
++ dma_dir = page_pool_get_dma_dir(rxq->page_pool);
++ dma_sync_single_for_cpu(dev->dev.parent,
++ rx_desc->buf_phys_addr,
++ len, dma_dir);
++ if (data_len > 0) {
++ /* refill descriptor with new buffer later */
++ skb_add_rx_frag(rxq->skb,
++ skb_shinfo(rxq->skb)->nr_frags,
++ page, NET_SKB_PAD, data_len,
++ PAGE_SIZE);
++ }
++ page_pool_release_page(rxq->page_pool, page);
++ rx_desc->buf_phys_addr = 0;
++ rxq->left_size -= len;
++}
++
+ /* Main rx processing when using software buffer management */
+ static int mvneta_rx_swbm(struct napi_struct *napi,
+ struct mvneta_port *pp, int budget,
+ struct mvneta_rx_queue *rxq)
+ {
++ int rcvd_pkts = 0, rcvd_bytes = 0, rx_proc = 0;
+ struct net_device *dev = pp->dev;
+- int rx_todo, rx_proc;
+- int refill = 0;
+- u32 rcvd_pkts = 0;
+- u32 rcvd_bytes = 0;
++ int rx_todo, refill;
+
+ /* Get number of received packets */
+ rx_todo = mvneta_rxq_busy_desc_num_get(pp, rxq);
+- rx_proc = 0;
+
+ /* Fairness NAPI loop */
+- while ((rcvd_pkts < budget) && (rx_proc < rx_todo)) {
++ while (rx_proc < budget && rx_proc < rx_todo) {
+ struct mvneta_rx_desc *rx_desc = mvneta_rxq_next_desc_get(rxq);
++ u32 rx_status, index;
+ unsigned char *data;
+ struct page *page;
+- dma_addr_t phys_addr;
+- u32 rx_status, index;
+- int rx_bytes, skb_size, copy_size;
+- int frag_num, frag_size, frag_offset;
+
+ index = rx_desc - rxq->descs;
+ page = (struct page *)rxq->buf_virt_addr[index];
+@@ -1991,100 +2067,30 @@ static int mvneta_rx_swbm(struct napi_st
+ /* Prefetch header */
+ prefetch(data);
+
+- phys_addr = rx_desc->buf_phys_addr;
+ rx_status = rx_desc->status;
+ rx_proc++;
+ rxq->refill_num++;
+
+ if (rx_status & MVNETA_RXD_FIRST_DESC) {
++ int err;
++
+ /* Check errors only for FIRST descriptor */
+ if (rx_status & MVNETA_RXD_ERR_SUMMARY) {
+ mvneta_rx_error(pp, rx_desc);
+ /* leave the descriptor untouched */
+ continue;
+ }
+- rx_bytes = rx_desc->data_size -
+- (ETH_FCS_LEN + MVNETA_MH_SIZE);
+-
+- /* Allocate small skb for each new packet */
+- skb_size = max(rx_copybreak, rx_header_size);
+- rxq->skb = netdev_alloc_skb_ip_align(dev, skb_size);
+- if (unlikely(!rxq->skb)) {
+- struct mvneta_pcpu_stats *stats = this_cpu_ptr(pp->stats);
+-
+- netdev_err(dev,
+- "Can't allocate skb on queue %d\n",
+- rxq->id);
+-
+- rxq->skb_alloc_err++;
+
+- u64_stats_update_begin(&stats->syncp);
+- stats->rx_dropped++;
+- u64_stats_update_end(&stats->syncp);
++ err = mvneta_swbm_rx_frame(pp, rx_desc, rxq, page);
++ if (err)
+ continue;
+- }
+- copy_size = min(skb_size, rx_bytes);
+-
+- /* Copy data from buffer to SKB, skip Marvell header */
+- memcpy(rxq->skb->data, data + MVNETA_MH_SIZE,
+- copy_size);
+- skb_put(rxq->skb, copy_size);
+- rxq->left_size = rx_bytes - copy_size;
+-
+- mvneta_rx_csum(pp, rx_status, rxq->skb);
+- if (rxq->left_size == 0) {
+- int size = copy_size + MVNETA_MH_SIZE;
+-
+- dma_sync_single_range_for_cpu(dev->dev.parent,
+- phys_addr, 0,
+- size,
+- DMA_FROM_DEVICE);
+-
+- /* leave the descriptor and buffer untouched */
+- } else {
+- /* refill descriptor with new buffer later */
+- rx_desc->buf_phys_addr = 0;
+-
+- frag_num = 0;
+- frag_offset = copy_size + MVNETA_MH_SIZE;
+- frag_size = min(rxq->left_size,
+- (int)(PAGE_SIZE - frag_offset));
+- skb_add_rx_frag(rxq->skb, frag_num, page,
+- frag_offset, frag_size,
+- PAGE_SIZE);
+- page_pool_release_page(rxq->page_pool, page);
+- rxq->left_size -= frag_size;
+- }
+ } else {
+- /* Middle or Last descriptor */
+ if (unlikely(!rxq->skb)) {
+ pr_debug("no skb for rx_status 0x%x\n",
+ rx_status);
+ continue;
+ }
+- if (!rxq->left_size) {
+- /* last descriptor has only FCS */
+- /* and can be discarded */
+- dma_sync_single_range_for_cpu(dev->dev.parent,
+- phys_addr, 0,
+- ETH_FCS_LEN,
+- DMA_FROM_DEVICE);
+- /* leave the descriptor and buffer untouched */
+- } else {
+- /* refill descriptor with new buffer later */
+- rx_desc->buf_phys_addr = 0;
+-
+- frag_num = skb_shinfo(rxq->skb)->nr_frags;
+- frag_offset = 0;
+- frag_size = min(rxq->left_size,
+- (int)(PAGE_SIZE - frag_offset));
+- skb_add_rx_frag(rxq->skb, frag_num, page,
+- frag_offset, frag_size,
+- PAGE_SIZE);
+-
+- page_pool_release_page(rxq->page_pool, page);
+- rxq->left_size -= frag_size;
+- }
++ mvneta_swbm_add_rx_fragment(pp, rx_desc, rxq, page);
+ } /* Middle or Last descriptor */
+
+ if (!(rx_status & MVNETA_RXD_LAST_DESC))
+@@ -2109,7 +2115,6 @@ static int mvneta_rx_swbm(struct napi_st
+
+ /* clean uncomplete skb pointer in queue */
+ rxq->skb = NULL;
+- rxq->left_size = 0;
+ }
+
+ if (rcvd_pkts)
+@@ -2970,7 +2975,7 @@ static void mvneta_rxq_hw_init(struct mv
+ /* Set Offset */
+ mvneta_rxq_offset_set(pp, rxq, 0);
+ mvneta_rxq_buf_size_set(pp, rxq, PAGE_SIZE < SZ_64K ?
+- PAGE_SIZE :
++ MVNETA_MAX_RX_BUF_SIZE :
+ MVNETA_RX_BUF_SIZE(pp->pkt_size));
+ mvneta_rxq_bm_disable(pp, rxq);
+ mvneta_rxq_fill(pp, rxq, rxq->size);
+@@ -4708,7 +4713,7 @@ static int mvneta_probe(struct platform_
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ pp->id = global_port_id++;
+- pp->rx_offset_correction = 0; /* not relevant for SW BM */
++ pp->rx_offset_correction = NET_SKB_PAD;
+
+ /* Obtain access to BM resources if enabled and already initialized */
+ bm_node = of_parse_phandle(dn, "buffer-manager", 0);
diff --git a/target/linux/mvebu/patches-5.10/006-net-mvneta-add-basic-XDP-support.patch b/target/linux/mvebu/patches-5.10/006-net-mvneta-add-basic-XDP-support.patch
new file mode 100644
index 0000000000..163632df51
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/006-net-mvneta-add-basic-XDP-support.patch
@@ -0,0 +1,311 @@
+From 0db51da7a8e99f0803ec3a8e25c1a66234a219cb Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:24 +0200
+Subject: [PATCH 4/7] net: mvneta: add basic XDP support
+
+Add basic XDP support to mvneta driver for devices that rely on software
+buffer management. Currently supported verdicts are:
+- XDP_DROP
+- XDP_PASS
+- XDP_REDIRECT
+- XDP_ABORTED
+
+- iptables drop:
+$iptables -t raw -I PREROUTING -p udp --dport 9 -j DROP
+$nstat -n && sleep 1 && nstat
+IpInReceives 151169 0.0
+IpExtInOctets 6953544 0.0
+IpExtInNoECTPkts 151165 0.0
+
+- XDP_DROP via xdp1
+$./samples/bpf/xdp1 3
+proto 0: 421419 pkt/s
+proto 0: 421444 pkt/s
+proto 0: 421393 pkt/s
+proto 0: 421440 pkt/s
+proto 0: 421184 pkt/s
+
+Tested-by: Matteo Croce <mcroce at redhat.com>
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 148 ++++++++++++++++++++++++--
+ 1 file changed, 139 insertions(+), 9 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -38,6 +38,7 @@
+ #include <net/ipv6.h>
+ #include <net/tso.h>
+ #include <net/page_pool.h>
++#include <linux/bpf_trace.h>
+
+ /* Registers */
+ #define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2))
+@@ -325,8 +326,10 @@
+ ETH_HLEN + ETH_FCS_LEN, \
+ cache_line_size())
+
++#define MVNETA_SKB_HEADROOM (max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + \
++ NET_IP_ALIGN)
+ #define MVNETA_SKB_PAD (SKB_DATA_ALIGN(sizeof(struct skb_shared_info) + \
+- NET_SKB_PAD))
++ MVNETA_SKB_HEADROOM))
+ #define MVNETA_SKB_SIZE(len) (SKB_DATA_ALIGN(len) + MVNETA_SKB_PAD)
+ #define MVNETA_MAX_RX_BUF_SIZE (PAGE_SIZE - MVNETA_SKB_PAD)
+
+@@ -354,6 +357,11 @@ struct mvneta_statistic {
+ #define T_REG_64 64
+ #define T_SW 1
+
++#define MVNETA_XDP_PASS BIT(0)
++#define MVNETA_XDP_DROPPED BIT(1)
++#define MVNETA_XDP_TX BIT(2)
++#define MVNETA_XDP_REDIR BIT(3)
++
+ static const struct mvneta_statistic mvneta_statistics[] = {
+ { 0x3000, T_REG_64, "good_octets_received", },
+ { 0x3010, T_REG_32, "good_frames_received", },
+@@ -435,6 +443,8 @@ struct mvneta_port {
+ u32 cause_rx_tx;
+ struct napi_struct napi;
+
++ struct bpf_prog *xdp_prog;
++
+ /* Core clock */
+ struct clk *clk;
+ /* AXI clock */
+@@ -1965,10 +1975,50 @@ int mvneta_rx_refill_queue(struct mvneta
+ }
+
+ static int
++mvneta_run_xdp(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
++ struct bpf_prog *prog, struct xdp_buff *xdp)
++{
++ u32 ret, act = bpf_prog_run_xdp(prog, xdp);
++
++ switch (act) {
++ case XDP_PASS:
++ ret = MVNETA_XDP_PASS;
++ break;
++ case XDP_REDIRECT: {
++ int err;
++
++ err = xdp_do_redirect(pp->dev, xdp, prog);
++ if (err) {
++ ret = MVNETA_XDP_DROPPED;
++ xdp_return_buff(xdp);
++ } else {
++ ret = MVNETA_XDP_REDIR;
++ }
++ break;
++ }
++ default:
++ bpf_warn_invalid_xdp_action(act);
++ /* fall through */
++ case XDP_ABORTED:
++ trace_xdp_exception(pp->dev, prog, act);
++ /* fall through */
++ case XDP_DROP:
++ page_pool_recycle_direct(rxq->page_pool,
++ virt_to_head_page(xdp->data));
++ ret = MVNETA_XDP_DROPPED;
++ break;
++ }
++
++ return ret;
++}
++
++static int
+ mvneta_swbm_rx_frame(struct mvneta_port *pp,
+ struct mvneta_rx_desc *rx_desc,
+ struct mvneta_rx_queue *rxq,
+- struct page *page)
++ struct xdp_buff *xdp,
++ struct bpf_prog *xdp_prog,
++ struct page *page, u32 *xdp_ret)
+ {
+ unsigned char *data = page_address(page);
+ int data_len = -MVNETA_MH_SIZE, len;
+@@ -1988,7 +2038,26 @@ mvneta_swbm_rx_frame(struct mvneta_port
+ rx_desc->buf_phys_addr,
+ len, dma_dir);
+
+- rxq->skb = build_skb(data, PAGE_SIZE);
++ xdp->data_hard_start = data;
++ xdp->data = data + MVNETA_SKB_HEADROOM + MVNETA_MH_SIZE;
++ xdp->data_end = xdp->data + data_len;
++ xdp_set_data_meta_invalid(xdp);
++
++ if (xdp_prog) {
++ u32 ret;
++
++ ret = mvneta_run_xdp(pp, rxq, xdp_prog, xdp);
++ if (ret != MVNETA_XDP_PASS) {
++ mvneta_update_stats(pp, 1,
++ xdp->data_end - xdp->data,
++ false);
++ rx_desc->buf_phys_addr = 0;
++ *xdp_ret |= ret;
++ return ret;
++ }
++ }
++
++ rxq->skb = build_skb(xdp->data_hard_start, PAGE_SIZE);
+ if (unlikely(!rxq->skb)) {
+ netdev_err(dev,
+ "Can't allocate skb on queue %d\n",
+@@ -1999,8 +2068,9 @@ mvneta_swbm_rx_frame(struct mvneta_port
+ }
+ page_pool_release_page(rxq->page_pool, page);
+
+- skb_reserve(rxq->skb, MVNETA_MH_SIZE + NET_SKB_PAD);
+- skb_put(rxq->skb, data_len);
++ skb_reserve(rxq->skb,
++ xdp->data - xdp->data_hard_start);
++ skb_put(rxq->skb, xdp->data_end - xdp->data);
+ mvneta_rx_csum(pp, rx_desc->status, rxq->skb);
+
+ rxq->left_size = rx_desc->data_size - len;
+@@ -2034,7 +2104,7 @@ mvneta_swbm_add_rx_fragment(struct mvnet
+ /* refill descriptor with new buffer later */
+ skb_add_rx_frag(rxq->skb,
+ skb_shinfo(rxq->skb)->nr_frags,
+- page, NET_SKB_PAD, data_len,
++ page, MVNETA_SKB_HEADROOM, data_len,
+ PAGE_SIZE);
+ }
+ page_pool_release_page(rxq->page_pool, page);
+@@ -2049,11 +2119,18 @@ static int mvneta_rx_swbm(struct napi_st
+ {
+ int rcvd_pkts = 0, rcvd_bytes = 0, rx_proc = 0;
+ struct net_device *dev = pp->dev;
++ struct bpf_prog *xdp_prog;
++ struct xdp_buff xdp_buf;
+ int rx_todo, refill;
++ u32 xdp_ret = 0;
+
+ /* Get number of received packets */
+ rx_todo = mvneta_rxq_busy_desc_num_get(pp, rxq);
+
++ rcu_read_lock();
++ xdp_prog = READ_ONCE(pp->xdp_prog);
++ xdp_buf.rxq = &rxq->xdp_rxq;
++
+ /* Fairness NAPI loop */
+ while (rx_proc < budget && rx_proc < rx_todo) {
+ struct mvneta_rx_desc *rx_desc = mvneta_rxq_next_desc_get(rxq);
+@@ -2081,7 +2158,8 @@ static int mvneta_rx_swbm(struct napi_st
+ continue;
+ }
+
+- err = mvneta_swbm_rx_frame(pp, rx_desc, rxq, page);
++ err = mvneta_swbm_rx_frame(pp, rx_desc, rxq, &xdp_buf,
++ xdp_prog, page, &xdp_ret);
+ if (err)
+ continue;
+ } else {
+@@ -2116,6 +2194,10 @@ static int mvneta_rx_swbm(struct napi_st
+ /* clean uncomplete skb pointer in queue */
+ rxq->skb = NULL;
+ }
++ rcu_read_unlock();
++
++ if (xdp_ret & MVNETA_XDP_REDIR)
++ xdp_do_flush_map();
+
+ if (rcvd_pkts)
+ mvneta_update_stats(pp, rcvd_pkts, rcvd_bytes, false);
+@@ -2857,13 +2939,14 @@ static int mvneta_poll(struct napi_struc
+ static int mvneta_create_page_pool(struct mvneta_port *pp,
+ struct mvneta_rx_queue *rxq, int size)
+ {
++ struct bpf_prog *xdp_prog = READ_ONCE(pp->xdp_prog);
+ struct page_pool_params pp_params = {
+ .order = 0,
+ .flags = PP_FLAG_DMA_MAP,
+ .pool_size = size,
+ .nid = cpu_to_node(0),
+ .dev = pp->dev->dev.parent,
+- .dma_dir = DMA_FROM_DEVICE,
++ .dma_dir = xdp_prog ? DMA_BIDIRECTIONAL : DMA_FROM_DEVICE,
+ };
+ int err;
+
+@@ -3364,6 +3447,11 @@ static int mvneta_change_mtu(struct net_
+ mtu = ALIGN(MVNETA_RX_PKT_SIZE(mtu), 8);
+ }
+
++ if (pp->xdp_prog && mtu > MVNETA_MAX_RX_BUF_SIZE) {
++ netdev_info(dev, "Illegal MTU value %d for XDP mode\n", mtu);
++ return -EINVAL;
++ }
++
+ dev->mtu = mtu;
+
+ if (!netif_running(dev)) {
+@@ -4029,6 +4117,47 @@ static int mvneta_ioctl(struct net_devic
+ return phylink_mii_ioctl(pp->phylink, ifr, cmd);
+ }
+
++static int mvneta_xdp_setup(struct net_device *dev, struct bpf_prog *prog,
++ struct netlink_ext_ack *extack)
++{
++ bool need_update, running = netif_running(dev);
++ struct mvneta_port *pp = netdev_priv(dev);
++ struct bpf_prog *old_prog;
++
++ if (prog && dev->mtu > MVNETA_MAX_RX_BUF_SIZE) {
++ NL_SET_ERR_MSG_MOD(extack, "Jumbo frames not supported on XDP");
++ return -EOPNOTSUPP;
++ }
++
++ need_update = !!pp->xdp_prog != !!prog;
++ if (running && need_update)
++ mvneta_stop(dev);
++
++ old_prog = xchg(&pp->xdp_prog, prog);
++ if (old_prog)
++ bpf_prog_put(old_prog);
++
++ if (running && need_update)
++ return mvneta_open(dev);
++
++ return 0;
++}
++
++static int mvneta_xdp(struct net_device *dev, struct netdev_bpf *xdp)
++{
++ struct mvneta_port *pp = netdev_priv(dev);
++
++ switch (xdp->command) {
++ case XDP_SETUP_PROG:
++ return mvneta_xdp_setup(dev, xdp->prog, xdp->extack);
++ case XDP_QUERY_PROG:
++ xdp->prog_id = pp->xdp_prog ? pp->xdp_prog->aux->id : 0;
++ return 0;
++ default:
++ return -EINVAL;
++ }
++}
++
+ /* Ethtool methods */
+
+ /* Set link ksettings (phy address, speed) for ethtools */
+@@ -4425,6 +4554,7 @@ static const struct net_device_ops mvnet
+ .ndo_fix_features = mvneta_fix_features,
+ .ndo_get_stats64 = mvneta_get_stats64,
+ .ndo_do_ioctl = mvneta_ioctl,
++ .ndo_bpf = mvneta_xdp,
+ };
+
+ static const struct ethtool_ops mvneta_eth_tool_ops = {
+@@ -4713,7 +4843,7 @@ static int mvneta_probe(struct platform_
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ pp->id = global_port_id++;
+- pp->rx_offset_correction = NET_SKB_PAD;
++ pp->rx_offset_correction = MVNETA_SKB_HEADROOM;
+
+ /* Obtain access to BM resources if enabled and already initialized */
+ bm_node = of_parse_phandle(dn, "buffer-manager", 0);
diff --git a/target/linux/mvebu/patches-5.10/007-gpio-mvebu-avoid_error_message_for_optional_IRQ.patch b/target/linux/mvebu/patches-5.10/007-gpio-mvebu-avoid_error_message_for_optional_IRQ.patch
new file mode 100644
index 0000000000..00d2b30d58
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/007-gpio-mvebu-avoid_error_message_for_optional_IRQ.patch
@@ -0,0 +1,31 @@
+From 525b0858ff2fdb78defec2d4d6d63baaa423d5fd Mon Sep 17 00:00:00 2001
+From: Chris Packham <chris.packham at alliedtelesis.co.nz>
+Date: Fri, 13 Mar 2020 16:42:44 +1300
+Subject: [PATCH] gpio: mvebu: avoid error message for optional IRQ
+
+platform_get_irq() will generate an error message if the requested irq
+is not present
+
+ mvebu-gpio f1010140.gpio: IRQ index 3 not found
+
+use platform_get_irq_optional() to avoid the error message being
+generated.
+
+Signed-off-by: Chris Packham <chris.packham at alliedtelesis.co.nz>
+Acked-by: Uwe Kleine-König <u.kleine-koenig at pengutronix.de>
+Signed-off-by: Bartosz Golaszewski <bgolaszewski at baylibre.com>
+---
+ drivers/gpio/gpio-mvebu.c | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+--- a/drivers/gpio/gpio-mvebu.c
++++ b/drivers/gpio/gpio-mvebu.c
+@@ -1248,7 +1248,7 @@ static int mvebu_gpio_probe(struct platf
+ * pins.
+ */
+ for (i = 0; i < 4; i++) {
+- int irq = platform_get_irq(pdev, i);
++ int irq = platform_get_irq_optional(pdev, i);
+
+ if (irq < 0)
+ continue;
diff --git a/target/linux/mvebu/patches-5.10/007-net-mvneta-move-header-prefetch-in-mvneta_swbm_rx_fr.patch b/target/linux/mvebu/patches-5.10/007-net-mvneta-move-header-prefetch-in-mvneta_swbm_rx_fr.patch
new file mode 100644
index 0000000000..e075796e41
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/007-net-mvneta-move-header-prefetch-in-mvneta_swbm_rx_fr.patch
@@ -0,0 +1,43 @@
+From fa383f6b77a2ed788266fa8fbfb659aa284d2f58 Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:25 +0200
+Subject: [PATCH 5/7] net: mvneta: move header prefetch in mvneta_swbm_rx_frame
+
+Move data buffer prefetch in mvneta_swbm_rx_frame after
+dma_sync_single_range_for_cpu
+
+Signed-off-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
+Signed-off-by: Jesper Dangaard Brouer <brouer at redhat.com>
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 7 +++----
+ 1 file changed, 3 insertions(+), 4 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -2038,6 +2038,9 @@ mvneta_swbm_rx_frame(struct mvneta_port
+ rx_desc->buf_phys_addr,
+ len, dma_dir);
+
++ /* Prefetch header */
++ prefetch(data);
++
+ xdp->data_hard_start = data;
+ xdp->data = data + MVNETA_SKB_HEADROOM + MVNETA_MH_SIZE;
+ xdp->data_end = xdp->data + data_len;
+@@ -2135,14 +2138,10 @@ static int mvneta_rx_swbm(struct napi_st
+ while (rx_proc < budget && rx_proc < rx_todo) {
+ struct mvneta_rx_desc *rx_desc = mvneta_rxq_next_desc_get(rxq);
+ u32 rx_status, index;
+- unsigned char *data;
+ struct page *page;
+
+ index = rx_desc - rxq->descs;
+ page = (struct page *)rxq->buf_virt_addr[index];
+- data = page_address(page);
+- /* Prefetch header */
+- prefetch(data);
+
+ rx_status = rx_desc->status;
+ rx_proc++;
diff --git a/target/linux/mvebu/patches-5.10/008-net-mvneta-make-tx-buffer-array-agnostic.patch b/target/linux/mvebu/patches-5.10/008-net-mvneta-make-tx-buffer-array-agnostic.patch
new file mode 100644
index 0000000000..e79aa816b8
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/008-net-mvneta-make-tx-buffer-array-agnostic.patch
@@ -0,0 +1,210 @@
+From 9e58c8b410650b5a6eb5b8fad8474bd8425a4023 Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:26 +0200
+Subject: [PATCH 6/7] net: mvneta: make tx buffer array agnostic
+
+Allow tx buffer array to contain both skb and xdp buffers in order to
+enable xdp frame recycling adding XDP_TX verdict support
+
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 66 +++++++++++++++++----------
+ 1 file changed, 43 insertions(+), 23 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -565,6 +565,20 @@ struct mvneta_rx_desc {
+ };
+ #endif
+
++enum mvneta_tx_buf_type {
++ MVNETA_TYPE_SKB,
++ MVNETA_TYPE_XDP_TX,
++ MVNETA_TYPE_XDP_NDO,
++};
++
++struct mvneta_tx_buf {
++ enum mvneta_tx_buf_type type;
++ union {
++ struct xdp_frame *xdpf;
++ struct sk_buff *skb;
++ };
++};
++
+ struct mvneta_tx_queue {
+ /* Number of this TX queue, in the range 0-7 */
+ u8 id;
+@@ -580,8 +594,8 @@ struct mvneta_tx_queue {
+ int tx_stop_threshold;
+ int tx_wake_threshold;
+
+- /* Array of transmitted skb */
+- struct sk_buff **tx_skb;
++ /* Array of transmitted buffers */
++ struct mvneta_tx_buf *buf;
+
+ /* Index of last TX DMA descriptor that was inserted */
+ int txq_put_index;
+@@ -1793,14 +1807,9 @@ static void mvneta_txq_bufs_free(struct
+ int i;
+
+ for (i = 0; i < num; i++) {
++ struct mvneta_tx_buf *buf = &txq->buf[txq->txq_get_index];
+ struct mvneta_tx_desc *tx_desc = txq->descs +
+ txq->txq_get_index;
+- struct sk_buff *skb = txq->tx_skb[txq->txq_get_index];
+-
+- if (skb) {
+- bytes_compl += skb->len;
+- pkts_compl++;
+- }
+
+ mvneta_txq_inc_get(txq);
+
+@@ -1808,9 +1817,12 @@ static void mvneta_txq_bufs_free(struct
+ dma_unmap_single(pp->dev->dev.parent,
+ tx_desc->buf_phys_addr,
+ tx_desc->data_size, DMA_TO_DEVICE);
+- if (!skb)
++ if (!buf->skb)
+ continue;
+- dev_kfree_skb_any(skb);
++
++ bytes_compl += buf->skb->len;
++ pkts_compl++;
++ dev_kfree_skb_any(buf->skb);
+ }
+
+ netdev_tx_completed_queue(nq, pkts_compl, bytes_compl);
+@@ -2335,16 +2347,19 @@ static inline void
+ mvneta_tso_put_hdr(struct sk_buff *skb,
+ struct mvneta_port *pp, struct mvneta_tx_queue *txq)
+ {
+- struct mvneta_tx_desc *tx_desc;
+ int hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
++ struct mvneta_tx_buf *buf = &txq->buf[txq->txq_put_index];
++ struct mvneta_tx_desc *tx_desc;
+
+- txq->tx_skb[txq->txq_put_index] = NULL;
+ tx_desc = mvneta_txq_next_desc_get(txq);
+ tx_desc->data_size = hdr_len;
+ tx_desc->command = mvneta_skb_tx_csum(pp, skb);
+ tx_desc->command |= MVNETA_TXD_F_DESC;
+ tx_desc->buf_phys_addr = txq->tso_hdrs_phys +
+ txq->txq_put_index * TSO_HEADER_SIZE;
++ buf->type = MVNETA_TYPE_SKB;
++ buf->skb = NULL;
++
+ mvneta_txq_inc_put(txq);
+ }
+
+@@ -2353,6 +2368,7 @@ mvneta_tso_put_data(struct net_device *d
+ struct sk_buff *skb, char *data, int size,
+ bool last_tcp, bool is_last)
+ {
++ struct mvneta_tx_buf *buf = &txq->buf[txq->txq_put_index];
+ struct mvneta_tx_desc *tx_desc;
+
+ tx_desc = mvneta_txq_next_desc_get(txq);
+@@ -2366,7 +2382,8 @@ mvneta_tso_put_data(struct net_device *d
+ }
+
+ tx_desc->command = 0;
+- txq->tx_skb[txq->txq_put_index] = NULL;
++ buf->type = MVNETA_TYPE_SKB;
++ buf->skb = NULL;
+
+ if (last_tcp) {
+ /* last descriptor in the TCP packet */
+@@ -2374,7 +2391,7 @@ mvneta_tso_put_data(struct net_device *d
+
+ /* last descriptor in SKB */
+ if (is_last)
+- txq->tx_skb[txq->txq_put_index] = skb;
++ buf->skb = skb;
+ }
+ mvneta_txq_inc_put(txq);
+ return 0;
+@@ -2459,6 +2476,7 @@ static int mvneta_tx_frag_process(struct
+ int i, nr_frags = skb_shinfo(skb)->nr_frags;
+
+ for (i = 0; i < nr_frags; i++) {
++ struct mvneta_tx_buf *buf = &txq->buf[txq->txq_put_index];
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ void *addr = skb_frag_address(frag);
+
+@@ -2478,12 +2496,13 @@ static int mvneta_tx_frag_process(struct
+ if (i == nr_frags - 1) {
+ /* Last descriptor */
+ tx_desc->command = MVNETA_TXD_L_DESC | MVNETA_TXD_Z_PAD;
+- txq->tx_skb[txq->txq_put_index] = skb;
++ buf->skb = skb;
+ } else {
+ /* Descriptor in the middle: Not First, Not Last */
+ tx_desc->command = 0;
+- txq->tx_skb[txq->txq_put_index] = NULL;
++ buf->skb = NULL;
+ }
++ buf->type = MVNETA_TYPE_SKB;
+ mvneta_txq_inc_put(txq);
+ }
+
+@@ -2511,6 +2530,7 @@ static netdev_tx_t mvneta_tx(struct sk_b
+ struct mvneta_port *pp = netdev_priv(dev);
+ u16 txq_id = skb_get_queue_mapping(skb);
+ struct mvneta_tx_queue *txq = &pp->txqs[txq_id];
++ struct mvneta_tx_buf *buf = &txq->buf[txq->txq_put_index];
+ struct mvneta_tx_desc *tx_desc;
+ int len = skb->len;
+ int frags = 0;
+@@ -2543,16 +2563,17 @@ static netdev_tx_t mvneta_tx(struct sk_b
+ goto out;
+ }
+
++ buf->type = MVNETA_TYPE_SKB;
+ if (frags == 1) {
+ /* First and Last descriptor */
+ tx_cmd |= MVNETA_TXD_FLZ_DESC;
+ tx_desc->command = tx_cmd;
+- txq->tx_skb[txq->txq_put_index] = skb;
++ buf->skb = skb;
+ mvneta_txq_inc_put(txq);
+ } else {
+ /* First but not Last */
+ tx_cmd |= MVNETA_TXD_F_DESC;
+- txq->tx_skb[txq->txq_put_index] = NULL;
++ buf->skb = NULL;
+ mvneta_txq_inc_put(txq);
+ tx_desc->command = tx_cmd;
+ /* Continue with other skb fragments */
+@@ -3138,9 +3159,8 @@ static int mvneta_txq_sw_init(struct mvn
+
+ txq->last_desc = txq->size - 1;
+
+- txq->tx_skb = kmalloc_array(txq->size, sizeof(*txq->tx_skb),
+- GFP_KERNEL);
+- if (!txq->tx_skb) {
++ txq->buf = kmalloc_array(txq->size, sizeof(*txq->buf), GFP_KERNEL);
++ if (!txq->buf) {
+ dma_free_coherent(pp->dev->dev.parent,
+ txq->size * MVNETA_DESC_ALIGNED_SIZE,
+ txq->descs, txq->descs_phys);
+@@ -3152,7 +3172,7 @@ static int mvneta_txq_sw_init(struct mvn
+ txq->size * TSO_HEADER_SIZE,
+ &txq->tso_hdrs_phys, GFP_KERNEL);
+ if (!txq->tso_hdrs) {
+- kfree(txq->tx_skb);
++ kfree(txq->buf);
+ dma_free_coherent(pp->dev->dev.parent,
+ txq->size * MVNETA_DESC_ALIGNED_SIZE,
+ txq->descs, txq->descs_phys);
+@@ -3205,7 +3225,7 @@ static void mvneta_txq_sw_deinit(struct
+ {
+ struct netdev_queue *nq = netdev_get_tx_queue(pp->dev, txq->id);
+
+- kfree(txq->tx_skb);
++ kfree(txq->buf);
+
+ if (txq->tso_hdrs)
+ dma_free_coherent(pp->dev->dev.parent,
diff --git a/target/linux/mvebu/patches-5.10/009-net-mvneta-add-XDP_TX-support.patch b/target/linux/mvebu/patches-5.10/009-net-mvneta-add-XDP_TX-support.patch
new file mode 100644
index 0000000000..c971030a1e
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/009-net-mvneta-add-XDP_TX-support.patch
@@ -0,0 +1,175 @@
+From b0a43db9087a21d96e1a0b716b8d9963064b2d58 Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Sat, 19 Oct 2019 10:13:27 +0200
+Subject: [PATCH 7/7] net: mvneta: add XDP_TX support
+
+Implement XDP_TX verdict and ndo_xdp_xmit net_device_ops function
+pointer
+
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 128 ++++++++++++++++++++++++--
+ 1 file changed, 121 insertions(+), 7 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -1813,16 +1813,19 @@ static void mvneta_txq_bufs_free(struct
+
+ mvneta_txq_inc_get(txq);
+
+- if (!IS_TSO_HEADER(txq, tx_desc->buf_phys_addr))
++ if (!IS_TSO_HEADER(txq, tx_desc->buf_phys_addr) &&
++ buf->type != MVNETA_TYPE_XDP_TX)
+ dma_unmap_single(pp->dev->dev.parent,
+ tx_desc->buf_phys_addr,
+ tx_desc->data_size, DMA_TO_DEVICE);
+- if (!buf->skb)
+- continue;
+-
+- bytes_compl += buf->skb->len;
+- pkts_compl++;
+- dev_kfree_skb_any(buf->skb);
++ if (buf->type == MVNETA_TYPE_SKB && buf->skb) {
++ bytes_compl += buf->skb->len;
++ pkts_compl++;
++ dev_kfree_skb_any(buf->skb);
++ } else if (buf->type == MVNETA_TYPE_XDP_TX ||
++ buf->type == MVNETA_TYPE_XDP_NDO) {
++ xdp_return_frame(buf->xdpf);
++ }
+ }
+
+ netdev_tx_completed_queue(nq, pkts_compl, bytes_compl);
+@@ -1987,6 +1990,111 @@ int mvneta_rx_refill_queue(struct mvneta
+ }
+
+ static int
++mvneta_xdp_submit_frame(struct mvneta_port *pp, struct mvneta_tx_queue *txq,
++ struct xdp_frame *xdpf, bool dma_map)
++{
++ struct mvneta_tx_desc *tx_desc;
++ struct mvneta_tx_buf *buf;
++ dma_addr_t dma_addr;
++
++ if (txq->count >= txq->tx_stop_threshold)
++ return MVNETA_XDP_DROPPED;
++
++ tx_desc = mvneta_txq_next_desc_get(txq);
++
++ buf = &txq->buf[txq->txq_put_index];
++ if (dma_map) {
++ /* ndo_xdp_xmit */
++ dma_addr = dma_map_single(pp->dev->dev.parent, xdpf->data,
++ xdpf->len, DMA_TO_DEVICE);
++ if (dma_mapping_error(pp->dev->dev.parent, dma_addr)) {
++ mvneta_txq_desc_put(txq);
++ return MVNETA_XDP_DROPPED;
++ }
++ buf->type = MVNETA_TYPE_XDP_NDO;
++ } else {
++ struct page *page = virt_to_page(xdpf->data);
++
++ dma_addr = page_pool_get_dma_addr(page) +
++ sizeof(*xdpf) + xdpf->headroom;
++ dma_sync_single_for_device(pp->dev->dev.parent, dma_addr,
++ xdpf->len, DMA_BIDIRECTIONAL);
++ buf->type = MVNETA_TYPE_XDP_TX;
++ }
++ buf->xdpf = xdpf;
++
++ tx_desc->command = MVNETA_TXD_FLZ_DESC;
++ tx_desc->buf_phys_addr = dma_addr;
++ tx_desc->data_size = xdpf->len;
++
++ mvneta_update_stats(pp, 1, xdpf->len, true);
++ mvneta_txq_inc_put(txq);
++ txq->pending++;
++ txq->count++;
++
++ return MVNETA_XDP_TX;
++}
++
++static int
++mvneta_xdp_xmit_back(struct mvneta_port *pp, struct xdp_buff *xdp)
++{
++ struct mvneta_tx_queue *txq;
++ struct netdev_queue *nq;
++ struct xdp_frame *xdpf;
++ int cpu;
++ u32 ret;
++
++ xdpf = convert_to_xdp_frame(xdp);
++ if (unlikely(!xdpf))
++ return MVNETA_XDP_DROPPED;
++
++ cpu = smp_processor_id();
++ txq = &pp->txqs[cpu % txq_number];
++ nq = netdev_get_tx_queue(pp->dev, txq->id);
++
++ __netif_tx_lock(nq, cpu);
++ ret = mvneta_xdp_submit_frame(pp, txq, xdpf, false);
++ if (ret == MVNETA_XDP_TX)
++ mvneta_txq_pend_desc_add(pp, txq, 0);
++ __netif_tx_unlock(nq);
++
++ return ret;
++}
++
++static int
++mvneta_xdp_xmit(struct net_device *dev, int num_frame,
++ struct xdp_frame **frames, u32 flags)
++{
++ struct mvneta_port *pp = netdev_priv(dev);
++ int cpu = smp_processor_id();
++ struct mvneta_tx_queue *txq;
++ struct netdev_queue *nq;
++ int i, drops = 0;
++ u32 ret;
++
++ if (unlikely(flags & ~XDP_XMIT_FLAGS_MASK))
++ return -EINVAL;
++
++ txq = &pp->txqs[cpu % txq_number];
++ nq = netdev_get_tx_queue(pp->dev, txq->id);
++
++ __netif_tx_lock(nq, cpu);
++ for (i = 0; i < num_frame; i++) {
++ ret = mvneta_xdp_submit_frame(pp, txq, frames[i], true);
++ if (ret != MVNETA_XDP_TX) {
++ xdp_return_frame_rx_napi(frames[i]);
++ drops++;
++ }
++ }
++
++ if (unlikely(flags & XDP_XMIT_FLUSH))
++ mvneta_txq_pend_desc_add(pp, txq, 0);
++ __netif_tx_unlock(nq);
++
++ return num_frame - drops;
++}
++
++static int
+ mvneta_run_xdp(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
+ struct bpf_prog *prog, struct xdp_buff *xdp)
+ {
+@@ -2008,6 +2116,11 @@ mvneta_run_xdp(struct mvneta_port *pp, s
+ }
+ break;
+ }
++ case XDP_TX:
++ ret = mvneta_xdp_xmit_back(pp, xdp);
++ if (ret != MVNETA_XDP_TX)
++ xdp_return_buff(xdp);
++ break;
+ default:
+ bpf_warn_invalid_xdp_action(act);
+ /* fall through */
+@@ -4574,6 +4687,7 @@ static const struct net_device_ops mvnet
+ .ndo_get_stats64 = mvneta_get_stats64,
+ .ndo_do_ioctl = mvneta_ioctl,
+ .ndo_bpf = mvneta_xdp,
++ .ndo_xdp_xmit = mvneta_xdp_xmit,
+ };
+
+ static const struct ethtool_ops mvneta_eth_tool_ops = {
diff --git a/target/linux/mvebu/patches-5.10/010-net-mvneta-fix-build-skb-for-bm-capable-devices.patch b/target/linux/mvebu/patches-5.10/010-net-mvneta-fix-build-skb-for-bm-capable-devices.patch
new file mode 100644
index 0000000000..adfa51e4e8
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/010-net-mvneta-fix-build-skb-for-bm-capable-devices.patch
@@ -0,0 +1,41 @@
+From b37fa92e20ef28aada852cbf03b368d29a20478c Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Thu, 14 Nov 2019 01:25:55 +0200
+Subject: [PATCH] net: mvneta: fix build skb for bm capable devices
+
+Fix build_skb for bm capable devices when they fall-back using swbm path
+(e.g. when bm properties are configured in device tree but
+CONFIG_MVNETA_BM_ENABLE is not set). In this case rx_offset_correction is
+overwritten so we need to use it building skb instead of
+MVNETA_SKB_HEADROOM directly
+
+Fixes: 8dc9a0888f4c ("net: mvneta: rely on build_skb in mvneta_rx_swbm poll routine")
+Fixes: 0db51da7a8e9 ("net: mvneta: add basic XDP support")
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Reported-by: Andrew Lunn <andrew at lunn.ch>
+Tested-by: Andrew Lunn <andrew at lunn.ch>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 4 ++--
+ 1 file changed, 2 insertions(+), 2 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -2167,7 +2167,7 @@ mvneta_swbm_rx_frame(struct mvneta_port
+ prefetch(data);
+
+ xdp->data_hard_start = data;
+- xdp->data = data + MVNETA_SKB_HEADROOM + MVNETA_MH_SIZE;
++ xdp->data = data + pp->rx_offset_correction + MVNETA_MH_SIZE;
+ xdp->data_end = xdp->data + data_len;
+ xdp_set_data_meta_invalid(xdp);
+
+@@ -2232,7 +2232,7 @@ mvneta_swbm_add_rx_fragment(struct mvnet
+ /* refill descriptor with new buffer later */
+ skb_add_rx_frag(rxq->skb,
+ skb_shinfo(rxq->skb)->nr_frags,
+- page, MVNETA_SKB_HEADROOM, data_len,
++ page, pp->rx_offset_correction, data_len,
+ PAGE_SIZE);
+ }
+ page_pool_release_page(rxq->page_pool, page);
diff --git a/target/linux/mvebu/patches-5.10/011-arm64-dts-uDPU-remove-i2c-fast-mode.patch b/target/linux/mvebu/patches-5.10/011-arm64-dts-uDPU-remove-i2c-fast-mode.patch
new file mode 100644
index 0000000000..2922d49f44
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/011-arm64-dts-uDPU-remove-i2c-fast-mode.patch
@@ -0,0 +1,31 @@
+From fe3ec631a77ded87817f449691710a436a80caa7 Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at armlinux.org.uk>
+Date: Sat, 16 Nov 2019 11:07:01 +0000
+Subject: [PATCH] arm64: dts: uDPU: remove i2c-fast-mode
+
+The I2C bus violates the timing specifications when run in fast mode
+on the uDPU, so switch to 100kHz mode.
+
+Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+@@ -119,12 +119,14 @@
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
++ /delete-property/mrvl,i2c-fast-mode;
+ };
+
+ &i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
++ /delete-property/mrvl,i2c-fast-mode;
+
+ lm75 at 48 {
+ status = "okay";
diff --git a/target/linux/mvebu/patches-5.10/012-arm64-dts-uDPU-SFP-cages-support-3W-modules.patch b/target/linux/mvebu/patches-5.10/012-arm64-dts-uDPU-SFP-cages-support-3W-modules.patch
new file mode 100644
index 0000000000..1884def2c6
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/012-arm64-dts-uDPU-SFP-cages-support-3W-modules.patch
@@ -0,0 +1,34 @@
+From cd592187f9de3c6305d6c1c66f7fac084cb5b846 Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at armlinux.org.uk>
+Date: Tue, 19 Nov 2019 22:53:04 +0000
+Subject: [PATCH] arm64: dts: uDPU: SFP cages support 3W modules
+
+The SFP cages are designed to support up to 3W modules, such as G.hn,
+G.fast and MoCA modules. Although there is no way for such modules to
+declare to software that they consume 3W, we document in DT that this
+is the designed power level for these cages.
+
+Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+@@ -69,6 +69,7 @@
+ mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
++ maximum-power-milliwatt = <3000>;
+ };
+
+ sfp_eth1: sfp-eth1 {
+@@ -78,6 +79,7 @@
+ mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+ tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
++ maximum-power-milliwatt = <3000>;
+ };
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/013-net-mvneta-rely-on-page_pool_recycle_direct-in-mvnet.patch b/target/linux/mvebu/patches-5.10/013-net-mvneta-rely-on-page_pool_recycle_direct-in-mvnet.patch
new file mode 100644
index 0000000000..6e79aeb358
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/013-net-mvneta-rely-on-page_pool_recycle_direct-in-mvnet.patch
@@ -0,0 +1,39 @@
+From f383b2950070ce4f34e74db94f70bb565b746e97 Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Wed, 20 Nov 2019 16:54:17 +0200
+Subject: [PATCH] net: mvneta: rely on page_pool_recycle_direct in
+ mvneta_run_xdp
+
+Rely on page_pool_recycle_direct and not on xdp_return_buff in
+mvneta_run_xdp. This is a preliminary patch to limit the dma sync len
+to the one strictly necessary
+
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Acked-by: Jesper Dangaard Brouer <brouer at redhat.com>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 6 ++++--
+ 1 file changed, 4 insertions(+), 2 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -2110,7 +2110,8 @@ mvneta_run_xdp(struct mvneta_port *pp, s
+ err = xdp_do_redirect(pp->dev, xdp, prog);
+ if (err) {
+ ret = MVNETA_XDP_DROPPED;
+- xdp_return_buff(xdp);
++ page_pool_recycle_direct(rxq->page_pool,
++ virt_to_head_page(xdp->data));
+ } else {
+ ret = MVNETA_XDP_REDIR;
+ }
+@@ -2119,7 +2120,8 @@ mvneta_run_xdp(struct mvneta_port *pp, s
+ case XDP_TX:
+ ret = mvneta_xdp_xmit_back(pp, xdp);
+ if (ret != MVNETA_XDP_TX)
+- xdp_return_buff(xdp);
++ page_pool_recycle_direct(rxq->page_pool,
++ virt_to_head_page(xdp->data));
+ break;
+ default:
+ bpf_warn_invalid_xdp_action(act);
diff --git a/target/linux/mvebu/patches-5.10/014-mvneta-driver-disallow-XDP-program-on-hardware-buffe.patch b/target/linux/mvebu/patches-5.10/014-mvneta-driver-disallow-XDP-program-on-hardware-buffe.patch
new file mode 100644
index 0000000000..e8a41d9eb2
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/014-mvneta-driver-disallow-XDP-program-on-hardware-buffe.patch
@@ -0,0 +1,53 @@
+From 79572c98c554dcdb080bca547c871a51716dcdf8 Mon Sep 17 00:00:00 2001
+From: Sven Auhagen <sven.auhagen at voleatech.de>
+Date: Sat, 25 Jan 2020 08:07:03 +0000
+Subject: [PATCH] mvneta driver disallow XDP program on hardware buffer
+ management
+
+Recently XDP Support was added to the mvneta driver
+for software buffer management only.
+It is still possible to attach an XDP program if
+hardware buffer management is used.
+It is not doing anything at that point.
+
+The patch disallows attaching XDP programs to mvneta
+if hardware buffer management is used.
+
+I am sorry about that. It is my first submission and I am having
+some troubles with the format of my emails.
+
+v4 -> v5:
+- Remove extra tabs
+
+v3 -> v4:
+- Please ignore v3 I accidentally submitted
+ my other patch with git-send-mail and v4 is correct
+
+v2 -> v3:
+- My mailserver corrupted the patch
+ resubmission with git-send-email
+
+v1 -> v2:
+- Fixing the patches indentation
+
+Signed-off-by: Sven Auhagen <sven.auhagen at voleatech.de>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 6 ++++++
+ 1 file changed, 6 insertions(+)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -4263,6 +4263,12 @@ static int mvneta_xdp_setup(struct net_d
+ return -EOPNOTSUPP;
+ }
+
++ if (pp->bm_priv) {
++ NL_SET_ERR_MSG_MOD(extack,
++ "Hardware Buffer Management not supported on XDP");
++ return -EOPNOTSUPP;
++ }
++
+ need_update = !!pp->xdp_prog != !!prog;
+ if (running && need_update)
+ mvneta_stop(dev);
diff --git a/target/linux/mvebu/patches-5.10/015-net-mvneta-fix-XDP-support-if-sw-bm-is-used-as-fallb.patch b/target/linux/mvebu/patches-5.10/015-net-mvneta-fix-XDP-support-if-sw-bm-is-used-as-fallb.patch
new file mode 100644
index 0000000000..86bffa538a
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/015-net-mvneta-fix-XDP-support-if-sw-bm-is-used-as-fallb.patch
@@ -0,0 +1,67 @@
+From 44efc78d0e464ce70b45b165c005f8bedc17952e Mon Sep 17 00:00:00 2001
+From: Lorenzo Bianconi <lorenzo at kernel.org>
+Date: Wed, 29 Jan 2020 12:50:53 +0100
+Subject: [PATCH] net: mvneta: fix XDP support if sw bm is used as fallback
+
+In order to fix XDP support if sw buffer management is used as fallback
+for hw bm devices, define MVNETA_SKB_HEADROOM as maximum between
+XDP_PACKET_HEADROOM and NET_SKB_PAD and let the hw aligns the IP header
+to 4-byte boundary.
+Fix rx_offset_correction initialization if mvneta_bm_port_init fails in
+mvneta_resume routine
+
+Fixes: 0db51da7a8e9 ("net: mvneta: add basic XDP support")
+Tested-by: Sven Auhagen <sven.auhagen at voleatech.de>
+Signed-off-by: Lorenzo Bianconi <lorenzo at kernel.org>
+Signed-off-by: David S. Miller <davem at davemloft.net>
+---
+ drivers/net/ethernet/marvell/mvneta.c | 10 +++++++---
+ 1 file changed, 7 insertions(+), 3 deletions(-)
+
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -326,8 +326,7 @@
+ ETH_HLEN + ETH_FCS_LEN, \
+ cache_line_size())
+
+-#define MVNETA_SKB_HEADROOM (max(XDP_PACKET_HEADROOM, NET_SKB_PAD) + \
+- NET_IP_ALIGN)
++#define MVNETA_SKB_HEADROOM max(XDP_PACKET_HEADROOM, NET_SKB_PAD)
+ #define MVNETA_SKB_PAD (SKB_DATA_ALIGN(sizeof(struct skb_shared_info) + \
+ MVNETA_SKB_HEADROOM))
+ #define MVNETA_SKB_SIZE(len) (SKB_DATA_ALIGN(len) + MVNETA_SKB_PAD)
+@@ -1174,6 +1173,7 @@ bm_mtu_err:
+ mvneta_bm_pool_destroy(pp->bm_priv, pp->pool_short, 1 << pp->id);
+
+ pp->bm_priv = NULL;
++ pp->rx_offset_correction = MVNETA_SKB_HEADROOM;
+ mvreg_write(pp, MVNETA_ACC_MODE, MVNETA_ACC_MODE_EXT1);
+ netdev_info(pp->dev, "fail to update MTU, fall back to software BM\n");
+ }
+@@ -4984,7 +4984,6 @@ static int mvneta_probe(struct platform_
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ pp->id = global_port_id++;
+- pp->rx_offset_correction = MVNETA_SKB_HEADROOM;
+
+ /* Obtain access to BM resources if enabled and already initialized */
+ bm_node = of_parse_phandle(dn, "buffer-manager", 0);
+@@ -5009,6 +5008,10 @@ static int mvneta_probe(struct platform_
+ }
+ of_node_put(bm_node);
+
++ /* sw buffer management */
++ if (!pp->bm_priv)
++ pp->rx_offset_correction = MVNETA_SKB_HEADROOM;
++
+ err = mvneta_init(&pdev->dev, pp);
+ if (err < 0)
+ goto err_netdev;
+@@ -5166,6 +5169,7 @@ static int mvneta_resume(struct device *
+ err = mvneta_bm_port_init(pdev, pp);
+ if (err < 0) {
+ dev_info(&pdev->dev, "use SW buffer management\n");
++ pp->rx_offset_correction = MVNETA_SKB_HEADROOM;
+ pp->bm_priv = NULL;
+ }
+ }
diff --git a/target/linux/mvebu/patches-5.10/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch b/target/linux/mvebu/patches-5.10/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
new file mode 100644
index 0000000000..c9e49ac2f1
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
@@ -0,0 +1,60 @@
+From 6964494582f56a3882c2c53b0edbfe99eb32b2e1 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Thu, 30 Apr 2020 10:06:14 +0200
+Subject: [PATCH] PCI: aardvark: Train link immediately after enabling training
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
+training and starting link training causes detection issues with some
+buggy cards (such as Compex WLE900VX).
+
+Move the code which enables link training immediately before the one
+which starts link traning.
+
+This fixes detection issues of Compex WLE900VX card on Turris MOX after
+cold boot.
+
+Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
+Fixes: f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready...")
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Acked-by: Rob Herring <robh at kernel.org>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 15 +++++++++------
+ 1 file changed, 9 insertions(+), 6 deletions(-)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -300,11 +300,6 @@ static void advk_pcie_setup_hw(struct ad
+ reg |= LANE_COUNT_1;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+- /* Enable link training */
+- reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+- reg |= LINK_TRAINING_EN;
+- advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+-
+ /* Enable MSI */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL2_REG);
+ reg |= PCIE_CORE_CTRL2_MSI_ENABLE;
+@@ -346,7 +341,15 @@ static void advk_pcie_setup_hw(struct ad
+ */
+ msleep(PCI_PM_D3COLD_WAIT);
+
+- /* Start link training */
++ /* Enable link training */
++ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
++ reg |= LINK_TRAINING_EN;
++ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
++
++ /*
++ * Start link training immediately after enabling it.
++ * This solves problems for some buggy cards.
++ */
+ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+ reg |= PCIE_CORE_LINK_TRAINING;
+ advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
diff --git a/target/linux/mvebu/patches-5.10/017-PCI-aardvark-Improve-link-training.patch b/target/linux/mvebu/patches-5.10/017-PCI-aardvark-Improve-link-training.patch
new file mode 100644
index 0000000000..2bf838432f
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/017-PCI-aardvark-Improve-link-training.patch
@@ -0,0 +1,208 @@
+From 43fc679ced18006b12d918d7a8a4af392b7fbfe7 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Marek=20Beh=C3=BAn?= <marek.behun at nic.cz>
+Date: Thu, 30 Apr 2020 10:06:17 +0200
+Subject: [PATCH] PCI: aardvark: Improve link training
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Currently the aardvark driver trains link in PCIe gen2 mode. This may
+cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
+even not detected. Moreover when ASPM code tries to retrain link second
+time, these cards may stop responding and link goes down. If gen1 is
+used this does not happen.
+
+Unconditionally forcing gen1 is not a good solution since it may have
+performance impact on gen2 cards.
+
+To overcome this, read 'max-link-speed' property (as defined in PCI
+device tree bindings) and use this as max gen mode. Then iteratively try
+link training at this mode or lower until successful. After successful
+link training choose final controller gen based on Negotiated Link Speed
+from Link Status register, which should match card speed.
+
+Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Signed-off-by: Marek Behún <marek.behun at nic.cz>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Reviewed-by: Rob Herring <robh at kernel.org>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 114 ++++++++++++++++++++------
+ 1 file changed, 89 insertions(+), 25 deletions(-)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -39,6 +39,7 @@
+ #define PCIE_CORE_LINK_CTRL_STAT_REG 0xd0
+ #define PCIE_CORE_LINK_L0S_ENTRY BIT(0)
+ #define PCIE_CORE_LINK_TRAINING BIT(5)
++#define PCIE_CORE_LINK_SPEED_SHIFT 16
+ #define PCIE_CORE_LINK_WIDTH_SHIFT 20
+ #define PCIE_CORE_ERR_CAPCTL_REG 0x118
+ #define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX BIT(5)
+@@ -201,6 +202,7 @@ struct advk_pcie {
+ struct mutex msi_used_lock;
+ u16 msi_msg;
+ int root_bus_nr;
++ int link_gen;
+ struct pci_bridge_emul bridge;
+ };
+
+@@ -225,20 +227,16 @@ static int advk_pcie_link_up(struct advk
+
+ static int advk_pcie_wait_for_link(struct advk_pcie *pcie)
+ {
+- struct device *dev = &pcie->pdev->dev;
+ int retries;
+
+ /* check if the link is up or not */
+ for (retries = 0; retries < LINK_WAIT_MAX_RETRIES; retries++) {
+- if (advk_pcie_link_up(pcie)) {
+- dev_info(dev, "link up\n");
++ if (advk_pcie_link_up(pcie))
+ return 0;
+- }
+
+ usleep_range(LINK_WAIT_USLEEP_MIN, LINK_WAIT_USLEEP_MAX);
+ }
+
+- dev_err(dev, "link never came up\n");
+ return -ETIMEDOUT;
+ }
+
+@@ -253,6 +251,85 @@ static void advk_pcie_wait_for_retrain(s
+ }
+ }
+
++static int advk_pcie_train_at_gen(struct advk_pcie *pcie, int gen)
++{
++ int ret, neg_gen;
++ u32 reg;
++
++ /* Setup link speed */
++ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
++ reg &= ~PCIE_GEN_SEL_MSK;
++ if (gen == 3)
++ reg |= SPEED_GEN_3;
++ else if (gen == 2)
++ reg |= SPEED_GEN_2;
++ else
++ reg |= SPEED_GEN_1;
++ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
++
++ /*
++ * Enable link training. This is not needed in every call to this
++ * function, just once suffices, but it does not break anything either.
++ */
++ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
++ reg |= LINK_TRAINING_EN;
++ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
++
++ /*
++ * Start link training immediately after enabling it.
++ * This solves problems for some buggy cards.
++ */
++ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
++ reg |= PCIE_CORE_LINK_TRAINING;
++ advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
++
++ ret = advk_pcie_wait_for_link(pcie);
++ if (ret)
++ return ret;
++
++ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
++ neg_gen = (reg >> PCIE_CORE_LINK_SPEED_SHIFT) & 0xf;
++
++ return neg_gen;
++}
++
++static void advk_pcie_train_link(struct advk_pcie *pcie)
++{
++ struct device *dev = &pcie->pdev->dev;
++ int neg_gen = -1, gen;
++
++ /*
++ * Try link training at link gen specified by device tree property
++ * 'max-link-speed'. If this fails, iteratively train at lower gen.
++ */
++ for (gen = pcie->link_gen; gen > 0; --gen) {
++ neg_gen = advk_pcie_train_at_gen(pcie, gen);
++ if (neg_gen > 0)
++ break;
++ }
++
++ if (neg_gen < 0)
++ goto err;
++
++ /*
++ * After successful training if negotiated gen is lower than requested,
++ * train again on negotiated gen. This solves some stability issues for
++ * some buggy gen1 cards.
++ */
++ if (neg_gen < gen) {
++ gen = neg_gen;
++ neg_gen = advk_pcie_train_at_gen(pcie, gen);
++ }
++
++ if (neg_gen == gen) {
++ dev_info(dev, "link up at gen %i\n", gen);
++ return;
++ }
++
++err:
++ dev_err(dev, "link never came up\n");
++}
++
+ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
+ {
+ u32 reg;
+@@ -288,12 +365,6 @@ static void advk_pcie_setup_hw(struct ad
+ PCIE_CORE_CTRL2_TD_ENABLE;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG);
+
+- /* Set GEN2 */
+- reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+- reg &= ~PCIE_GEN_SEL_MSK;
+- reg |= SPEED_GEN_2;
+- advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+-
+ /* Set lane X1 */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg &= ~LANE_CNT_MSK;
+@@ -341,20 +412,7 @@ static void advk_pcie_setup_hw(struct ad
+ */
+ msleep(PCI_PM_D3COLD_WAIT);
+
+- /* Enable link training */
+- reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+- reg |= LINK_TRAINING_EN;
+- advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+-
+- /*
+- * Start link training immediately after enabling it.
+- * This solves problems for some buggy cards.
+- */
+- reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+- reg |= PCIE_CORE_LINK_TRAINING;
+- advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
+-
+- advk_pcie_wait_for_link(pcie);
++ advk_pcie_train_link(pcie);
+
+ reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
+ reg |= PCIE_CORE_CMD_MEM_ACCESS_EN |
+@@ -1035,6 +1093,12 @@ static int advk_pcie_probe(struct platfo
+ return ret;
+ }
+
++ ret = of_pci_get_max_link_speed(dev->of_node);
++ if (ret <= 0 || ret > 3)
++ pcie->link_gen = 3;
++ else
++ pcie->link_gen = ret;
++
+ advk_pcie_setup_hw(pcie);
+
+ ret = advk_sw_pci_bridge_init(pcie);
diff --git a/target/linux/mvebu/patches-5.10/018-PCI-aardvark-Issue-PERST-via-GPIO.patch b/target/linux/mvebu/patches-5.10/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
new file mode 100644
index 0000000000..83212ec475
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
@@ -0,0 +1,123 @@
+From 5169a9851daaa2782a7bd2bb83d5b1bd224b2879 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Thu, 30 Apr 2020 10:06:18 +0200
+Subject: [PATCH] PCI: aardvark: Issue PERST via GPIO
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Add support for issuing PERST via GPIO specified in 'reset-gpios'
+property (as described in PCI device tree bindings).
+
+Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
+after reboot when PERST is not issued during driver initialization.
+
+If bootloader already enabled link training then issuing PERST has no
+effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
+not detected. We therefore clear the LINK_TRAINING_EN register before.
+
+It was observed that Compex WLE900VX card needs to be in PERST reset
+for at least 10ms if bootloader enabled link training.
+
+Tested on Turris MOX.
+
+Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 43 ++++++++++++++++++++++++++-
+ 1 file changed, 42 insertions(+), 1 deletion(-)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -9,6 +9,7 @@
+ */
+
+ #include <linux/delay.h>
++#include <linux/gpio.h>
+ #include <linux/interrupt.h>
+ #include <linux/irq.h>
+ #include <linux/irqdomain.h>
+@@ -17,6 +18,7 @@
+ #include <linux/init.h>
+ #include <linux/platform_device.h>
+ #include <linux/of_address.h>
++#include <linux/of_gpio.h>
+ #include <linux/of_pci.h>
+
+ #include "../pci.h"
+@@ -204,6 +206,7 @@ struct advk_pcie {
+ int root_bus_nr;
+ int link_gen;
+ struct pci_bridge_emul bridge;
++ struct gpio_desc *reset_gpio;
+ };
+
+ static inline void advk_writel(struct advk_pcie *pcie, u32 val, u64 reg)
+@@ -330,10 +333,31 @@ err:
+ dev_err(dev, "link never came up\n");
+ }
+
++static void advk_pcie_issue_perst(struct advk_pcie *pcie)
++{
++ u32 reg;
++
++ if (!pcie->reset_gpio)
++ return;
++
++ /* PERST does not work for some cards when link training is enabled */
++ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
++ reg &= ~LINK_TRAINING_EN;
++ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
++
++ /* 10ms delay is needed for some cards */
++ dev_info(&pcie->pdev->dev, "issuing PERST via reset GPIO for 10ms\n");
++ gpiod_set_value_cansleep(pcie->reset_gpio, 1);
++ usleep_range(10000, 11000);
++ gpiod_set_value_cansleep(pcie->reset_gpio, 0);
++}
++
+ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
+ {
+ u32 reg;
+
++ advk_pcie_issue_perst(pcie);
++
+ /* Set to Direct mode */
+ reg = advk_readl(pcie, CTRL_CONFIG_REG);
+ reg &= ~(CTRL_MODE_MASK << CTRL_MODE_SHIFT);
+@@ -406,7 +430,8 @@ static void advk_pcie_setup_hw(struct ad
+
+ /*
+ * PERST# signal could have been asserted by pinctrl subsystem before
+- * probe() callback has been called, making the endpoint going into
++ * probe() callback has been called or issued explicitly by reset gpio
++ * function advk_pcie_issue_perst(), making the endpoint going into
+ * fundamental reset. As required by PCI Express spec a delay for at
+ * least 100ms after such a reset before link training is needed.
+ */
+@@ -1093,6 +1118,22 @@ static int advk_pcie_probe(struct platfo
+ return ret;
+ }
+
++ pcie->reset_gpio = devm_gpiod_get_from_of_node(dev, dev->of_node,
++ "reset-gpios", 0,
++ GPIOD_OUT_LOW,
++ "pcie1-reset");
++ ret = PTR_ERR_OR_ZERO(pcie->reset_gpio);
++ if (ret) {
++ if (ret == -ENOENT) {
++ pcie->reset_gpio = NULL;
++ } else {
++ if (ret != -EPROBE_DEFER)
++ dev_err(dev, "Failed to get reset-gpio: %i\n",
++ ret);
++ return ret;
++ }
++ }
++
+ ret = of_pci_get_max_link_speed(dev->of_node);
+ if (ret <= 0 || ret > 3)
+ pcie->link_gen = 3;
diff --git a/target/linux/mvebu/patches-5.10/019-PCI-aardvark-Add-PHY-support.patch b/target/linux/mvebu/patches-5.10/019-PCI-aardvark-Add-PHY-support.patch
new file mode 100644
index 0000000000..fa04861e80
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/019-PCI-aardvark-Add-PHY-support.patch
@@ -0,0 +1,152 @@
+From 366697018c9a2aa67d457bfdc495115cface6ae8 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Marek=20Beh=C3=BAn?= <marek.behun at nic.cz>
+Date: Thu, 30 Apr 2020 10:06:20 +0200
+Subject: [PATCH] PCI: aardvark: Add PHY support
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+With recent proposed changes for U-Boot it is possible that bootloader
+won't initialize the PHY for this controller (currently the PHY is
+initialized regardless whether PCI is used in U-Boot, but with these
+proposed changes the PHY is initialized only on request).
+
+Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
+PCIe PHY, and since Linux' functionality should be independent on what
+bootloader did, add code for enabling generic PHY if found in device OF
+node.
+
+The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
+Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
+one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
+Instead ARM Trusted Firmware expects PCIe driver to do this step,
+probably because the register is in PCIe controller address space,
+instead of PHY address space. We therefore add this step into the
+advk_pcie_setup_hw function.
+
+[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
+
+Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Signed-off-by: Marek Behún <marek.behun at nic.cz>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Reviewed-by: Rob Herring <robh at kernel.org>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+Cc: Miquèl Raynal <miquel.raynal at bootlin.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 69 +++++++++++++++++++++++++++
+ 1 file changed, 69 insertions(+)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -16,6 +16,7 @@
+ #include <linux/kernel.h>
+ #include <linux/pci.h>
+ #include <linux/init.h>
++#include <linux/phy/phy.h>
+ #include <linux/platform_device.h>
+ #include <linux/of_address.h>
+ #include <linux/of_gpio.h>
+@@ -103,6 +104,8 @@
+ #define PCIE_CORE_CTRL2_STRICT_ORDER_ENABLE BIT(5)
+ #define PCIE_CORE_CTRL2_OB_WIN_ENABLE BIT(6)
+ #define PCIE_CORE_CTRL2_MSI_ENABLE BIT(10)
++#define PCIE_CORE_REF_CLK_REG (CONTROL_BASE_ADDR + 0x14)
++#define PCIE_CORE_REF_CLK_TX_ENABLE BIT(1)
+ #define PCIE_MSG_LOG_REG (CONTROL_BASE_ADDR + 0x30)
+ #define PCIE_ISR0_REG (CONTROL_BASE_ADDR + 0x40)
+ #define PCIE_MSG_PM_PME_MASK BIT(7)
+@@ -207,6 +210,7 @@ struct advk_pcie {
+ int link_gen;
+ struct pci_bridge_emul bridge;
+ struct gpio_desc *reset_gpio;
++ struct phy *phy;
+ };
+
+ static inline void advk_writel(struct advk_pcie *pcie, u32 val, u64 reg)
+@@ -358,6 +362,11 @@ static void advk_pcie_setup_hw(struct ad
+
+ advk_pcie_issue_perst(pcie);
+
++ /* Enable TX */
++ reg = advk_readl(pcie, PCIE_CORE_REF_CLK_REG);
++ reg |= PCIE_CORE_REF_CLK_TX_ENABLE;
++ advk_writel(pcie, reg, PCIE_CORE_REF_CLK_REG);
++
+ /* Set to Direct mode */
+ reg = advk_readl(pcie, CTRL_CONFIG_REG);
+ reg &= ~(CTRL_MODE_MASK << CTRL_MODE_SHIFT);
+@@ -1083,6 +1092,62 @@ out_release_res:
+ return err;
+ }
+
++static void __maybe_unused advk_pcie_disable_phy(struct advk_pcie *pcie)
++{
++ phy_power_off(pcie->phy);
++ phy_exit(pcie->phy);
++}
++
++static int advk_pcie_enable_phy(struct advk_pcie *pcie)
++{
++ int ret;
++
++ if (!pcie->phy)
++ return 0;
++
++ ret = phy_init(pcie->phy);
++ if (ret)
++ return ret;
++
++ ret = phy_set_mode(pcie->phy, PHY_MODE_PCIE);
++ if (ret) {
++ phy_exit(pcie->phy);
++ return ret;
++ }
++
++ ret = phy_power_on(pcie->phy);
++ if (ret) {
++ phy_exit(pcie->phy);
++ return ret;
++ }
++
++ return 0;
++}
++
++static int advk_pcie_setup_phy(struct advk_pcie *pcie)
++{
++ struct device *dev = &pcie->pdev->dev;
++ struct device_node *node = dev->of_node;
++ int ret = 0;
++
++ pcie->phy = devm_of_phy_get(dev, node, NULL);
++ if (IS_ERR(pcie->phy) && (PTR_ERR(pcie->phy) == -EPROBE_DEFER))
++ return PTR_ERR(pcie->phy);
++
++ /* Old bindings miss the PHY handle */
++ if (IS_ERR(pcie->phy)) {
++ dev_warn(dev, "PHY unavailable (%ld)\n", PTR_ERR(pcie->phy));
++ pcie->phy = NULL;
++ return 0;
++ }
++
++ ret = advk_pcie_enable_phy(pcie);
++ if (ret)
++ dev_err(dev, "Failed to initialize PHY (%d)\n", ret);
++
++ return ret;
++}
++
+ static int advk_pcie_probe(struct platform_device *pdev)
+ {
+ struct device *dev = &pdev->dev;
+@@ -1140,6 +1205,10 @@ static int advk_pcie_probe(struct platfo
+ else
+ pcie->link_gen = ret;
+
++ ret = advk_pcie_setup_phy(pcie);
++ if (ret)
++ return ret;
++
+ advk_pcie_setup_hw(pcie);
+
+ ret = advk_sw_pci_bridge_init(pcie);
diff --git a/target/linux/mvebu/patches-5.10/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch b/target/linux/mvebu/patches-5.10/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
new file mode 100644
index 0000000000..87247b63ad
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
@@ -0,0 +1,93 @@
+From 715878016984b2617f6c1f177c50039e12e7bd5b Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Marek=20Beh=C3=BAn?= <marek.behun at nic.cz>
+Date: Thu, 30 Apr 2020 10:06:23 +0200
+Subject: [PATCH] arm64: dts: marvell: armada-37xx: Set pcie_reset_pin to gpio
+ function
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+We found out that we are unable to control the PERST# signal via the
+default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
+this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
+register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
+value of this register does not change the pin output when measuring
+with voltmeter.
+
+We do not know if this is a bug in the SOC, or if it works only when
+PCIe controller is in a certain state.
+
+Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
+before training link") says that when this pin changes pinctrl mode
+from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
+moment.
+
+So currently the situation is that on A3700 boards the PERST# signal is
+asserted in U-Boot (because the code in U-Boot issues reset via this pin
+via GPIO mode), and then in Linux by the obscure and undocumented
+mechanism described by the above mentioned commit.
+
+We want to issue PERST# signal in a known way, therefore this patch
+changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
+reset-gpios property to the PCIe node in device tree files of
+EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
+has this property and uDPU does not have a PCIe port).
+
+Signed-off-by: Marek Behún <marek.behun at nic.cz>
+Cc: Remi Pommarel <repk at triplefau.lt>
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-db.dts | 3 +++
+ arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 1 +
+ arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts | 4 ----
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 2 +-
+ 4 files changed, 5 insertions(+), 5 deletions(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+@@ -128,6 +128,9 @@
+
+ /* CON15(V2.0)/CON17(V1.4) : PCIe / CON15(V2.0)/CON12(V1.4) :mini-PCIe */
+ &pcie0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
++ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+@@ -59,6 +59,7 @@
+ phys = <&comphy1 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
++ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+ };
+
+ /* J6 */
+--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+@@ -120,10 +120,6 @@
+ };
+ };
+
+-&pcie_reset_pins {
+- function = "gpio";
+-};
+-
+ &pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -317,7 +317,7 @@
+
+ pcie_reset_pins: pcie-reset-pins {
+ groups = "pcie1";
+- function = "pcie";
++ function = "gpio";
+ };
+
+ pcie_clkreq_pins: pcie-clkreq-pins {
diff --git a/target/linux/mvebu/patches-5.10/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch b/target/linux/mvebu/patches-5.10/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch
new file mode 100644
index 0000000000..e92393ff6f
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch
@@ -0,0 +1,57 @@
+From df749cdb015011e9ed8b60ebb84b4e76a9f35735 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Marek=20Beh=C3=BAn?= <marek.behun at nic.cz>
+Date: Thu, 30 Apr 2020 10:06:24 +0200
+Subject: [PATCH] arm64: dts: marvell: armada-37xx: Move PCIe comphy handle
+ property
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Move the comphy handle property of the PCIe node from board specific
+device tree files (EspressoBin and Turris Mox) to the generic
+armada-37xx.dtsi.
+
+This is correct since this is the only possible PCIe PHY configuration
+on Armada 37xx, so when PCIe is enabled on any board, this handle is
+correct.
+
+Signed-off-by: Marek Behún <marek.behun at nic.cz>
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 1 -
+ arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts | 1 -
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
+ 3 files changed, 1 insertion(+), 2 deletions(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+@@ -56,7 +56,6 @@
+ /* J9 */
+ &pcie0 {
+ status = "okay";
+- phys = <&comphy1 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+@@ -126,7 +126,6 @@
+ status = "okay";
+ max-link-speed = <2>;
+ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+- phys = <&comphy1 0>;
+
+ /* enabled by U-Boot if PCIe module is present */
+ status = "disabled";
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -493,6 +493,7 @@
+ <0 0 0 2 &pcie_intc 1>,
+ <0 0 0 3 &pcie_intc 2>,
+ <0 0 0 4 &pcie_intc 3>;
++ phys = <&comphy1 0>;
+ pcie_intc: interrupt-controller {
+ interrupt-controller;
+ #interrupt-cells = <1>;
diff --git a/target/linux/mvebu/patches-5.10/022-arm64-dts-marvell-armada-37xx-Move-PCIe-max-link-spe.patch b/target/linux/mvebu/patches-5.10/022-arm64-dts-marvell-armada-37xx-Move-PCIe-max-link-spe.patch
new file mode 100644
index 0000000000..ad918bef88
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/022-arm64-dts-marvell-armada-37xx-Move-PCIe-max-link-spe.patch
@@ -0,0 +1,44 @@
+From 1b5a2dd9e266d78d5fddd7e6b116e47ba9577b5e Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Thu, 30 Apr 2020 10:06:25 +0200
+Subject: [PATCH] arm64: dts: marvell: armada-37xx: Move PCIe max-link-speed
+ property
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Move the max-link-speed property of the PCIe node from board specific
+device tree files to the generic armada-37xx.dtsi.
+
+Armada 37xx supports only PCIe gen2 speed so max-link-speed property
+should be in the generic armada-37xx.dtsi file.
+
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Acked-by: Thomas Petazzoni <thomas.petazzoni at bootlin.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts | 1 -
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
+ 2 files changed, 1 insertion(+), 1 deletion(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+@@ -124,7 +124,6 @@
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+ status = "okay";
+- max-link-speed = <2>;
+ reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+
+ /* enabled by U-Boot if PCIe module is present */
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -493,6 +493,7 @@
+ <0 0 0 2 &pcie_intc 1>,
+ <0 0 0 3 &pcie_intc 2>,
+ <0 0 0 4 &pcie_intc 3>;
++ max-link-speed = <2>;
+ phys = <&comphy1 0>;
+ pcie_intc: interrupt-controller {
+ interrupt-controller;
diff --git a/target/linux/mvebu/patches-5.10/023-arm64-dts-add-uDPU-i2c-bus-recovery.patch b/target/linux/mvebu/patches-5.10/023-arm64-dts-add-uDPU-i2c-bus-recovery.patch
new file mode 100644
index 0000000000..818fce85a8
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/023-arm64-dts-add-uDPU-i2c-bus-recovery.patch
@@ -0,0 +1,53 @@
+From 11b2af36cc874027ce701c5784cb957c99c7de3d Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at armlinux.org.uk>
+Date: Wed, 6 May 2020 10:40:37 +0100
+Subject: [PATCH] arm64: dts: add uDPU i2c bus recovery
+
+Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
+Reviewed-by: Andrew Lunn <andrew at lunn.ch>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ .../boot/dts/marvell/armada-3720-uDPU.dts | 22 +++++++++++++++++--
+ 1 file changed, 20 insertions(+), 2 deletions(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+@@ -117,18 +117,36 @@
+ };
+ };
+
++&pinctrl_nb {
++ i2c1_recovery_pins: i2c1-recovery-pins {
++ groups = "i2c1";
++ function = "gpio";
++ };
++
++ i2c2_recovery_pins: i2c2-recovery-pins {
++ groups = "i2c2";
++ function = "gpio";
++ };
++};
++
+ &i2c0 {
+ status = "okay";
+- pinctrl-names = "default";
++ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&i2c1_pins>;
++ pinctrl-1 = <&i2c1_recovery_pins>;
+ /delete-property/mrvl,i2c-fast-mode;
++ scl-gpios = <&gpionb 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
++ sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ };
+
+ &i2c1 {
+ status = "okay";
+- pinctrl-names = "default";
++ pinctrl-names = "default", "recovery";
+ pinctrl-0 = <&i2c2_pins>;
++ pinctrl-1 = <&i2c2_recovery_pins>;
+ /delete-property/mrvl,i2c-fast-mode;
++ scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
++ sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+ lm75 at 48 {
+ status = "okay";
diff --git a/target/linux/mvebu/patches-5.10/024-PCI-aardvark-Don-t-touch-PCIe-registers-if-no-card-c.patch b/target/linux/mvebu/patches-5.10/024-PCI-aardvark-Don-t-touch-PCIe-registers-if-no-card-c.patch
new file mode 100644
index 0000000000..dfc068c8cb
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/024-PCI-aardvark-Don-t-touch-PCIe-registers-if-no-card-c.patch
@@ -0,0 +1,50 @@
+From 70e380250c3621c55ff218cbaf2272830d9dbb1d Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Thu, 2 Jul 2020 10:30:36 +0200
+Subject: [PATCH] PCI: aardvark: Don't touch PCIe registers if no card
+ connected
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+When there is no PCIe card connected and advk_pcie_rd_conf() or
+advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
+root bridge, the aardvark driver throws the following error message:
+
+ advk-pcie d0070000.pcie: config read/write timed out
+
+Obviously accessing PCIe registers of disconnected card is not possible.
+
+Extend check in advk_pcie_valid_device() function for validating
+availability of PCIe bus. If PCIe link is down, then the device is marked
+as Not Found and the driver does not try to access these registers.
+
+This is just an optimization to prevent accessing PCIe registers when card
+is disconnected. Trying to access PCIe registers of disconnected card does
+not cause any crash, kernel just needs to wait for a timeout. So if card
+disappear immediately after checking for PCIe link (before accessing PCIe
+registers), it does not cause any problems.
+
+Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+---
+ drivers/pci/controller/pci-aardvark.c | 7 +++++++
+ 1 file changed, 7 insertions(+)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -639,6 +639,13 @@ static bool advk_pcie_valid_device(struc
+ if ((bus->number == pcie->root_bus_nr) && PCI_SLOT(devfn) != 0)
+ return false;
+
++ /*
++ * If the link goes down after we check for link-up, nothing bad
++ * happens but the config access times out.
++ */
++ if (bus->number != pcie->root_bus_nr && !advk_pcie_link_up(pcie))
++ return false;
++
+ return true;
+ }
+
diff --git a/target/linux/mvebu/patches-5.10/025-power-reset-add-driver-for-LinkStation-power-off.patch b/target/linux/mvebu/patches-5.10/025-power-reset-add-driver-for-LinkStation-power-off.patch
new file mode 100644
index 0000000000..64ea26559e
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/025-power-reset-add-driver-for-LinkStation-power-off.patch
@@ -0,0 +1,207 @@
+From a7f79f99541eff4e6bcae0014eb08d3019337565 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Daniel=20Gonz=C3=A1lez=20Cabanelas?= <dgcbueu at gmail.com>
+Date: Wed, 15 Jul 2020 15:35:14 +0200
+Subject: [PATCH] power: reset: add driver for LinkStation power off
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Some Buffalo LinkStations perform the power off operation, at restart
+time, depending on the state of an output pin (LED2/INTn) at the ethernet
+PHY. This pin is also used to wake the machine when a WoL packet is
+received by the PHY.
+
+The driver is required by the Buffalo LinkStation LS421DE (ARM MVEBU),
+and other models. Without it, the board remains forever halted if a
+power off command is executed, unless the PSU is disconnected and
+connected again.
+
+Add the driver to provide the power off function and also make the WoL
+feature to be available.
+
+Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
+Signed-off-by: Sebastian Reichel <sebastian.reichel at collabora.com>
+---
+ drivers/power/reset/Kconfig | 11 ++
+ drivers/power/reset/Makefile | 1 +
+ drivers/power/reset/linkstation-poweroff.c | 136 +++++++++++++++++++++
+ 3 files changed, 148 insertions(+)
+ create mode 100644 drivers/power/reset/linkstation-poweroff.c
+
+--- a/drivers/power/reset/Kconfig
++++ b/drivers/power/reset/Kconfig
+@@ -99,6 +99,17 @@ config POWER_RESET_HISI
+ help
+ Reboot support for Hisilicon boards.
+
++config POWER_RESET_LINKSTATION
++ tristate "Buffalo LinkStation power-off driver"
++ depends on ARCH_MVEBU || COMPILE_TEST
++ depends on OF_MDIO && PHYLIB
++ help
++ This driver supports turning off some Buffalo LinkStations by
++ setting an output pin at the ethernet PHY to the correct state.
++ It also makes the device compatible with the WoL function.
++
++ Say Y here if you have a Buffalo LinkStation LS421D/E.
++
+ config POWER_RESET_MSM
+ bool "Qualcomm MSM power-off driver"
+ depends on ARCH_QCOM
+--- a/drivers/power/reset/Makefile
++++ b/drivers/power/reset/Makefile
+@@ -10,6 +10,7 @@ obj-$(CONFIG_POWER_RESET_GEMINI_POWEROFF
+ obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
+ obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o
+ obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o
++obj-${CONFIG_POWER_RESET_LINKSTATION} += linkstation-poweroff.o
+ obj-$(CONFIG_POWER_RESET_MSM) += msm-poweroff.o
+ obj-$(CONFIG_POWER_RESET_QCOM_PON) += qcom-pon.o
+ obj-$(CONFIG_POWER_RESET_OCELOT_RESET) += ocelot-reset.o
+--- /dev/null
++++ b/drivers/power/reset/linkstation-poweroff.c
+@@ -0,0 +1,144 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * LinkStation power off restart driver
++ * Copyright (C) 2020 Daniel González Cabanelas <dgcbueu at gmail.com>
++ */
++
++#include <linux/module.h>
++#include <linux/notifier.h>
++#include <linux/of.h>
++#include <linux/of_mdio.h>
++#include <linux/of_platform.h>
++#include <linux/reboot.h>
++#include <linux/phy.h>
++
++/* Defines from the eth phy Marvell driver */
++#define MII_MARVELL_COPPER_PAGE 0
++#define MII_MARVELL_LED_PAGE 3
++#define MII_MARVELL_WOL_PAGE 17
++#define MII_MARVELL_PHY_PAGE 22
++
++#define MII_PHY_LED_CTRL 16
++#define MII_88E1318S_PHY_LED_TCR 18
++#define MII_88E1318S_PHY_WOL_CTRL 16
++#define MII_M1011_IEVENT 19
++
++#define MII_88E1318S_PHY_LED_TCR_INTn_ENABLE BIT(7)
++#define MII_88E1318S_PHY_LED_TCR_FORCE_INT BIT(15)
++#define MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS BIT(12)
++#define LED2_FORCE_ON (0x8 << 8)
++#define LEDMASK GENMASK(11,8)
++
++static struct phy_device *phydev;
++
++static void mvphy_reg_intn(u16 data)
++{
++ int rc = 0, saved_page;
++
++ saved_page = phy_select_page(phydev, MII_MARVELL_LED_PAGE);
++ if (saved_page < 0)
++ goto err;
++
++ /* Force manual LED2 control to let INTn work */
++ __phy_modify(phydev, MII_PHY_LED_CTRL, LEDMASK, LED2_FORCE_ON);
++
++ /* Set the LED[2]/INTn pin to the required state */
++ __phy_modify(phydev, MII_88E1318S_PHY_LED_TCR,
++ MII_88E1318S_PHY_LED_TCR_FORCE_INT,
++ MII_88E1318S_PHY_LED_TCR_INTn_ENABLE | data);
++
++ if (!data) {
++ /* Clear interrupts to ensure INTn won't be holded in high state */
++ __phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_MARVELL_COPPER_PAGE);
++ __phy_read(phydev, MII_M1011_IEVENT);
++
++ /* If WOL was enabled and a magic packet was received before powering
++ * off, we won't be able to wake up by sending another magic packet.
++ * Clear WOL status.
++ */
++ __phy_write(phydev, MII_MARVELL_PHY_PAGE, MII_MARVELL_WOL_PAGE);
++ __phy_set_bits(phydev, MII_88E1318S_PHY_WOL_CTRL,
++ MII_88E1318S_PHY_WOL_CTRL_CLEAR_WOL_STATUS);
++ }
++err:
++ rc = phy_restore_page(phydev, saved_page, rc);
++ if (rc < 0)
++ dev_err(&phydev->mdio.dev, "Write register failed, %d\n", rc);
++
++ if (!data) {
++ /* Slow down the PHY to save energy */
++ rc= phy_speed_down(phydev, false);
++ if (rc < 0)
++ dev_err(&phydev->mdio.dev, "PHY speed down failed, %d\n", rc);
++ }
++}
++
++static int linkstation_reboot_notifier(struct notifier_block *nb,
++ unsigned long action, void *unused)
++{
++ if (action == SYS_RESTART)
++ mvphy_reg_intn(MII_88E1318S_PHY_LED_TCR_FORCE_INT);
++
++ return NOTIFY_DONE;
++}
++
++static struct notifier_block linkstation_reboot_nb = {
++ .notifier_call = linkstation_reboot_notifier,
++};
++
++static void linkstation_poweroff(void)
++{
++ unregister_reboot_notifier(&linkstation_reboot_nb);
++ mvphy_reg_intn(0);
++
++ kernel_restart("Power off");
++}
++
++static const struct of_device_id ls_poweroff_of_match[] = {
++ { .compatible = "buffalo,ls421d" },
++ { .compatible = "buffalo,ls421de" },
++ { },
++};
++
++static int __init linkstation_poweroff_init(void)
++{
++ struct mii_bus *bus;
++ struct device_node *dn;
++
++ dn = of_find_matching_node(NULL, ls_poweroff_of_match);
++ if (!dn)
++ return -ENODEV;
++ of_node_put(dn);
++
++ dn = of_find_node_by_name(NULL, "mdio");
++ if (!dn)
++ return -ENODEV;
++
++ bus = of_mdio_find_bus(dn);
++ of_node_put(dn);
++ if (!bus)
++ return -EPROBE_DEFER;
++
++ phydev = phy_find_first(bus);
++ if (!phydev)
++ return -EPROBE_DEFER;
++
++ register_reboot_notifier(&linkstation_reboot_nb);
++ pm_power_off = linkstation_poweroff;
++
++ pr_info("LinkStation power off driver registered\n");
++ return 0;
++}
++
++static void __exit linkstation_poweroff_exit(void)
++{
++ pm_power_off = NULL;
++ unregister_reboot_notifier(&linkstation_reboot_nb);
++}
++
++module_init(linkstation_poweroff_init);
++module_exit(linkstation_poweroff_exit);
++
++MODULE_AUTHOR("Daniel González Cabanelas <dgcbueu at gmail.com>");
++MODULE_DESCRIPTION("LinkStation power off driver");
++MODULE_LICENSE("GPL v2");
diff --git a/target/linux/mvebu/patches-5.10/026-PCI-aardvark-Fix-initialization-with-old-Marvell-s-A.patch b/target/linux/mvebu/patches-5.10/026-PCI-aardvark-Fix-initialization-with-old-Marvell-s-A.patch
new file mode 100644
index 0000000000..bb9d7b7849
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/026-PCI-aardvark-Fix-initialization-with-old-Marvell-s-A.patch
@@ -0,0 +1,44 @@
+From b0c6ae0f8948a2be6bf4e8b4bbab9ca1343289b6 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Wed, 2 Sep 2020 16:43:44 +0200
+Subject: [PATCH] PCI: aardvark: Fix initialization with old Marvell's Arm
+ Trusted Firmware
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Old ATF automatically power on pcie phy and does not provide SMC call for
+phy power on functionality which leads to aardvark initialization failure:
+
+[ 0.330134] mvebu-a3700-comphy d0018300.phy: unsupported SMC call, try updating your firmware
+[ 0.338846] phy phy-d0018300.phy.1: phy poweron failed --> -95
+[ 0.344753] advk-pcie d0070000.pcie: Failed to initialize PHY (-95)
+[ 0.351160] advk-pcie: probe of d0070000.pcie failed with error -95
+
+This patch fixes above failure by ignoring 'not supported' error in
+aardvark driver. In this case it is expected that phy is already power on.
+
+Tested-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Link: https://lore.kernel.org/r/20200902144344.16684-3-pali@kernel.org
+Fixes: 366697018c9a ("PCI: aardvark: Add PHY support")
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi at arm.com>
+Reviewed-by: Rob Herring <robh at kernel.org>
+Cc: <stable at vger.kernel.org> # 5.8+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
+---
+ drivers/pci/controller/pci-aardvark.c | 4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+--- a/drivers/pci/controller/pci-aardvark.c
++++ b/drivers/pci/controller/pci-aardvark.c
+@@ -1123,7 +1123,9 @@ static int advk_pcie_enable_phy(struct a
+ }
+
+ ret = phy_power_on(pcie->phy);
+- if (ret) {
++ if (ret == -EOPNOTSUPP) {
++ dev_warn(&pcie->pdev->dev, "PHY unsupported by firmware\n");
++ } else if (ret) {
+ phy_exit(pcie->phy);
+ return ret;
+ }
diff --git a/target/linux/mvebu/patches-5.10/027-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch b/target/linux/mvebu/patches-5.10/027-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch
new file mode 100644
index 0000000000..927670d8b3
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/027-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch
@@ -0,0 +1,88 @@
+From b64d814257b027e29a474bcd660f6372490138c7 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Pali=20Roh=C3=A1r?= <pali at kernel.org>
+Date: Mon, 7 Sep 2020 13:27:17 +0200
+Subject: [PATCH] arm64: dts: marvell: espressobin: Add ethernet switch aliases
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Espressobin boards have 3 ethernet ports and some of them got assigned more
+then one MAC address. MAC addresses are stored in U-Boot environment.
+
+Since commit a2c7023f7075c ("net: dsa: read mac address from DT for slave
+device") kernel can use MAC addresses from DT for particular DSA port.
+
+Currently Espressobin DTS file contains alias just for ethernet0.
+
+This patch defines additional ethernet aliases in Espressobin DTS files, so
+bootloader can fill correct MAC address for DSA switch ports if more MAC
+addresses were specified.
+
+DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
+are used for lan ports for both Espressobin revisions (V5 and V7).
+
+Fixes: 5253cb8c00a6f ("arm64: dts: marvell: espressobin: add ethernet alias")
+Cc: <stable at vger.kernel.org> # a2c7023f7075c: dsa: read mac address
+Signed-off-by: Pali Rohár <pali at kernel.org>
+Reviewed-by: Andrew Lunn <andrew at lunn.ch>
+Reviewed-by: Andre Heider <a.heider at gmail.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ .../dts/marvell/armada-3720-espressobin-v7-emmc.dts | 10 ++++++++--
+ .../boot/dts/marvell/armada-3720-espressobin-v7.dts | 10 ++++++++--
+ 3 files changed, 24 insertions(+), 8 deletions(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7-emmc.dts
+@@ -15,16 +15,22 @@
+ compatible = "globalscale,espressobin-v7-emmc", "globalscale,espressobin-v7",
+ "globalscale,espressobin", "marvell,armada3720",
+ "marvell,armada3710";
++
++ aliases {
++ /* ethernet1 is wan port */
++ ethernet1 = &switch0port3;
++ ethernet3 = &switch0port1;
++ };
+ };
+
+ &ports {
+- port at 1 {
++ switch0port1: port at 1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&switch0phy0>;
+ };
+
+- port at 3 {
++ switch0port3: port at 3 {
+ reg = <3>;
+ label = "wan";
+ phy-handle = <&switch0phy2>;
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts
+@@ -14,16 +14,22 @@
+ model = "Globalscale Marvell ESPRESSOBin Board V7";
+ compatible = "globalscale,espressobin-v7", "globalscale,espressobin",
+ "marvell,armada3720", "marvell,armada3710";
++
++ aliases {
++ /* ethernet1 is wan port */
++ ethernet1 = &switch0port3;
++ ethernet3 = &switch0port1;
++ };
+ };
+
+ &ports {
+- port at 1 {
++ switch0port1: port at 1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&switch0phy0>;
+ };
+
+- port at 3 {
++ switch0port3: port at 3 {
+ reg = <3>;
+ label = "wan";
+ phy-handle = <&switch0phy2>;
diff --git a/target/linux/mvebu/patches-5.10/028-arm64-dts-mcbin-singleshot-add-heartbeat-LED.patch b/target/linux/mvebu/patches-5.10/028-arm64-dts-mcbin-singleshot-add-heartbeat-LED.patch
new file mode 100644
index 0000000000..c3abae60a6
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/028-arm64-dts-mcbin-singleshot-add-heartbeat-LED.patch
@@ -0,0 +1,65 @@
+From da57203dc7fd556fbb3f0ec7d7d7c0b0e893b386 Mon Sep 17 00:00:00 2001
+From: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Date: Tue, 10 Nov 2020 16:38:31 +0100
+Subject: [PATCH] arm64: dts: mcbin-singleshot: add heartbeat LED
+
+With board revision 1.3, SolidRun moved the power LED to the middle of
+the board. In old place of power LED a GPIO controllable heartbeat LED
+was added. This commit only touches Single Shot variant, since only this
+variant is all revision 1.3.
+
+Note:
+This is slightly modified patch. Some boards could be placed in an
+enclosure, so the LED18 is enabled by default, since that'll be the only
+visible indicator that the board is operating.
+
+Reported-by: Alexandra Alth <alexandra at alth.de>
+Signed-off-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Signed-off-by: Gregory CLEMENT <gregory.clement at bootlin.com>
+---
+ .../marvell/armada-8040-mcbin-singleshot.dts | 22 +++++++++++++++++++
+ 1 file changed, 22 insertions(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts
++++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin-singleshot.dts
+@@ -5,6 +5,8 @@
+ * Device Tree file for MACCHIATOBin Armada 8040 community board platform
+ */
+
++#include <dt-bindings/leds/common.h>
++
+ #include "armada-8040-mcbin.dtsi"
+
+ / {
+@@ -12,6 +14,20 @@
+ compatible = "marvell,armada8040-mcbin-singleshot",
+ "marvell,armada8040-mcbin", "marvell,armada8040",
+ "marvell,armada-ap806-quad", "marvell,armada-ap806";
++
++ leds {
++ compatible = "gpio-leds";
++ pinctrl-0 = <&cp0_led18_pins>;
++ pinctrl-names = "default";
++
++ led18 {
++ gpios = <&cp0_gpio2 1 GPIO_ACTIVE_LOW>;
++ function = LED_FUNCTION_HEARTBEAT;
++ color = <LED_COLOR_ID_GREEN>;
++ linux,default-trigger = "heartbeat";
++ default-state = "on";
++ };
++ };
+ };
+
+ &cp0_eth0 {
+@@ -27,3 +43,10 @@
+ managed = "in-band-status";
+ sfp = <&sfp_eth1>;
+ };
++
++&cp0_pinctrl {
++ cp0_led18_pins: led18-pins {
++ marvell,pins = "mpp33";
++ marvell,function = "gpio";
++ };
++};
diff --git a/target/linux/mvebu/patches-5.10/300-mvebu-Mangle-bootloader-s-kernel-arguments.patch b/target/linux/mvebu/patches-5.10/300-mvebu-Mangle-bootloader-s-kernel-arguments.patch
new file mode 100644
index 0000000000..fd60cdb322
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/300-mvebu-Mangle-bootloader-s-kernel-arguments.patch
@@ -0,0 +1,208 @@
+From 71270226b14733a4b1f2cde58ea9265caa50b38d Mon Sep 17 00:00:00 2001
+From: Adrian Panella <ianchi74 at outlook.com>
+Date: Thu, 9 Mar 2017 09:37:17 +0100
+Subject: [PATCH 67/69] generic: Mangle bootloader's kernel arguments
+
+The command-line arguments provided by the boot loader will be
+appended to a new device tree property: bootloader-args.
+If there is a property "append-rootblock" in DT under /chosen
+and a root= option in bootloaders command line it will be parsed
+and added to DT bootargs with the form: <append-rootblock>XX.
+Only command line ATAG will be processed, the rest of the ATAGs
+sent by bootloader will be ignored.
+This is usefull in dual boot systems, to get the current root partition
+without afecting the rest of the system.
+
+Signed-off-by: Adrian Panella <ianchi74 at outlook.com>
+
+This patch has been modified to be mvebu specific. The original patch
+did not pass the bootloader cmdline on if no append-rootblock stanza
+was found, resulting in blank cmdline and failure to boot.
+
+Signed-off-by: Michael Gray <michael.gray at lantisproject.com>
+---
+ arch/arm/Kconfig | 11 ++++
+ arch/arm/boot/compressed/atags_to_fdt.c | 85 ++++++++++++++++++++++++-
+ init/main.c | 16 +++++
+ 3 files changed, 111 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/Kconfig
++++ b/arch/arm/Kconfig
+@@ -1827,6 +1827,17 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN
+ The command-line arguments provided by the boot loader will be
+ appended to the the device tree bootargs property.
+
++config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE
++ bool "Append rootblock parsing bootloader's kernel arguments"
++ help
++ The command-line arguments provided by the boot loader will be
++ appended to a new device tree property: bootloader-args.
++ If there is a property "append-rootblock" in DT under /chosen
++ and a root= option in bootloaders command line it will be parsed
++ and added to DT bootargs with the form: <append-rootblock>XX.
++ Only command line ATAG will be processed, the rest of the ATAGs
++ sent by bootloader will be ignored.
++
+ endchoice
+
+ config CMDLINE
+--- a/arch/arm/boot/compressed/atags_to_fdt.c
++++ b/arch/arm/boot/compressed/atags_to_fdt.c
+@@ -4,6 +4,8 @@
+
+ #if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND)
+ #define do_extend_cmdline 1
++#elif defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++#define do_extend_cmdline 1
+ #else
+ #define do_extend_cmdline 0
+ #endif
+@@ -67,6 +69,72 @@ static uint32_t get_cell_size(const void
+ return cell_size;
+ }
+
++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++
++static char *append_rootblock(char *dest, const char *str, int len, void *fdt)
++{
++ char *ptr, *end;
++ char *root="root=";
++ int i, l;
++ const char *rootblock;
++
++ //ARM doesn't have __HAVE_ARCH_STRSTR, so search manually
++ ptr = str - 1;
++
++ do {
++ //first find an 'r' at the begining or after a space
++ do {
++ ptr++;
++ ptr = strchr(ptr, 'r');
++ if (!ptr)
++ goto no_append;
++
++ } while (ptr != str && *(ptr-1) != ' ');
++
++ //then check for the rest
++ for(i = 1; i <= 4; i++)
++ if(*(ptr+i) != *(root+i)) break;
++
++ } while (i != 5);
++
++ end = strchr(ptr, ' ');
++ end = end ? (end - 1) : (strchr(ptr, 0) - 1);
++
++ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX )
++ for( i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++);
++ ptr = end + 1;
++
++ /* if append-rootblock property is set use it to append to command line */
++ rootblock = getprop(fdt, "/chosen", "append-rootblock", &l);
++ if (rootblock == NULL)
++ goto no_append;
++
++ if (*dest != ' ') {
++ *dest = ' ';
++ dest++;
++ len++;
++ }
++
++ if (len + l + i <= COMMAND_LINE_SIZE) {
++ memcpy(dest, rootblock, l);
++ dest += l - 1;
++ memcpy(dest, ptr, i);
++ dest += i;
++ }
++
++ return dest;
++
++no_append:
++ len = strlen(str);
++ if (len + 1 < COMMAND_LINE_SIZE) {
++ memcpy(dest, str, len);
++ dest += len;
++ }
++
++ return dest;
++}
++#endif
++
+ static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline)
+ {
+ char cmdline[COMMAND_LINE_SIZE];
+@@ -86,12 +154,21 @@ static void merge_fdt_bootargs(void *fdt
+
+ /* and append the ATAG_CMDLINE */
+ if (fdt_cmdline) {
++
++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++ //save original bootloader args
++ //and append ubi.mtd with root partition number to current cmdline
++ setprop_string(fdt, "/chosen", "bootloader-args", fdt_cmdline);
++ ptr = append_rootblock(ptr, fdt_cmdline, len, fdt);
++
++#else
+ len = strlen(fdt_cmdline);
+ if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) {
+ *ptr++ = ' ';
+ memcpy(ptr, fdt_cmdline, len);
+ ptr += len;
+ }
++#endif
+ }
+ *ptr = '\0';
+
+@@ -166,7 +243,9 @@ int atags_to_fdt(void *atag_list, void *
+ else
+ setprop_string(fdt, "/chosen", "bootargs",
+ atag->u.cmdline.cmdline);
+- } else if (atag->hdr.tag == ATAG_MEM) {
++ }
++#ifndef CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE
++ else if (atag->hdr.tag == ATAG_MEM) {
+ if (memcount >= sizeof(mem_reg_property)/4)
+ continue;
+ if (!atag->u.mem.size)
+@@ -210,6 +289,10 @@ int atags_to_fdt(void *atag_list, void *
+ setprop(fdt, "/memory", "reg", mem_reg_property,
+ 4 * memcount * memsize);
+ }
++#else
++
++ }
++#endif
+
+ return fdt_pack(fdt);
+ }
+--- a/init/main.c
++++ b/init/main.c
+@@ -104,6 +104,10 @@
+ #define CREATE_TRACE_POINTS
+ #include <trace/events/initcall.h>
+
++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++#include <linux/of.h>
++#endif
++
+ static int kernel_init(void *);
+
+ extern void init_IRQ(void);
+@@ -631,6 +635,18 @@ asmlinkage __visible void __init start_k
+ page_alloc_init();
+
+ pr_notice("Kernel command line: %s\n", boot_command_line);
++
++#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++ //Show bootloader's original command line for reference
++ if(of_chosen) {
++ const char *prop = of_get_property(of_chosen, "bootloader-args", NULL);
++ if(prop)
++ pr_notice("Bootloader command line (ignored): %s\n", prop);
++ else
++ pr_notice("Bootloader command line not present\n");
++ }
++#endif
++
+ /* parameters may set static keys */
+ jump_label_init();
+ parse_early_param();
diff --git a/target/linux/mvebu/patches-5.10/301-mvebu-armada-38x-enable-libata-leds.patch b/target/linux/mvebu/patches-5.10/301-mvebu-armada-38x-enable-libata-leds.patch
new file mode 100644
index 0000000000..b8ab700c97
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/301-mvebu-armada-38x-enable-libata-leds.patch
@@ -0,0 +1,10 @@
+--- a/arch/arm/mach-mvebu/Kconfig
++++ b/arch/arm/mach-mvebu/Kconfig
+@@ -69,6 +69,7 @@ config MACH_ARMADA_38X
+ select HAVE_SMP
+ select MACH_MVEBU_V7
+ select PINCTRL_ARMADA_38X
++ select ARCH_WANT_LIBATA_LEDS
+ help
+ Say 'Y' here if you want your kernel to support boards based
+ on the Marvell Armada 380/385 SoC with device tree.
diff --git a/target/linux/mvebu/patches-5.10/302-add_powertables.patch b/target/linux/mvebu/patches-5.10/302-add_powertables.patch
new file mode 100644
index 0000000000..efbbbc7d78
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/302-add_powertables.patch
@@ -0,0 +1,770 @@
+--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
++++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
+@@ -212,11 +212,19 @@
+ &pcie1 {
+ /* Marvell 88W8864, 5GHz-only */
+ status = "okay";
++
++ mwlwifi {
++ marvell,2ghz = <0>;
++ };
+ };
+
+ &pcie2 {
+ /* Marvell 88W8864, 2GHz-only */
+ status = "okay";
++
++ mwlwifi {
++ marvell,5ghz = <0>;
++ };
+ };
+
+ &pinctrl {
+--- a/arch/arm/boot/dts/armada-385-linksys-caiman.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
+@@ -142,3 +142,205 @@
+ };
+ };
+ };
++
++&pcie1 {
++ mwlwifi {
++ marvell,chainmask = <2 2>;
++ marvell,powertable {
++ AU =
++ <36 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <40 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <44 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <48 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <100 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <104 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <108 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <112 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <116 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <120 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <124 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <128 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <132 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <136 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <140 0 0x17 0x17 0x17 0x17 0x17 0x17 0x17 0x15 0x17 0x17 0x17 0x14 0x17 0x17 0x17 0x14 0 0xf>,
++ <149 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x1a 0x1a 0x17 0x14 0 0xf>,
++ <153 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x1a 0x1a 0x17 0x14 0 0xf>,
++ <157 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x1a 0x1a 0x17 0x14 0 0xf>,
++ <161 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x1a 0x1a 0x17 0x14 0 0xf>,
++ <165 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x1a 0x1a 0x17 0x14 0 0xf>;
++ CA =
++ <36 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0 0xf>,
++ <40 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0 0xf>,
++ <44 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0 0xf>,
++ <48 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x1a 0x1a 0x18 0x17 0x19 0x19 0x17 0x15 0x18 0x18 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <153 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <157 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <161 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <165 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>;
++ CN =
++ <36 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <40 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <44 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <48 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <100 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <149 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x11 0x11 0x11 0x11 0 0xf>,
++ <153 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0 0xf>,
++ <157 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0 0xf>,
++ <161 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0 0xf>,
++ <165 0 0x15 0x15 0x15 0x15 0x16 0x16 0x16 0x15 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0 0xf>;
++ ETSI =
++ <36 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <40 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <44 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <48 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <100 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>,
++ <149 0 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0 0xf>;
++ FCC =
++ <36 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <40 0 0x19 0x19 0x18 0x17 0x19 0x19 0x17 0x15 0x17 0x17 0x17 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <44 0 0x19 0x19 0x18 0x17 0x19 0x19 0x17 0x15 0x17 0x17 0x17 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <48 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x17 0x17 0x17 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x1a 0x1a 0x18 0x17 0x19 0x19 0x17 0x15 0x18 0x18 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <153 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <157 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <161 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>,
++ <165 0 0x1a 0x1a 0x18 0x17 0x1a 0x1a 0x17 0x15 0x1a 0x1a 0x17 0x14 0x15 0x15 0x15 0x14 0 0xf>;
++ };
++ };
++};
++
++&pcie2 {
++ mwlwifi {
++ marvell,chainmask = <2 2>;
++ marvell,powertable {
++ AU =
++ <1 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>;
++ CA =
++ <1 0 0x19 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x10 0x10 0x10 0x10 0x00 0x00 0x00 0x00 0 0xf>,
++ <2 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <3 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <4 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <5 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <6 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <7 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <8 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <9 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <10 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x00 0x00 0x00 0x00 0 0xf>,
++ <11 0 0x19 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x00 0x00 0x00 0x00 0 0xf>;
++ CN =
++ <1 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <14 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>;
++ ETSI =
++ <1 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0x0 0x0 0x0 0x0 0 0xf>;
++ FCC =
++ <1 0 0x19 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x1a 0x19 0x18 0x17 0x19 0x19 0x17 0x16 0x14 0x14 0x14 0x14 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x19 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x0 0x0 0x0 0x0 0 0xf>;
++ };
++ };
++};
+--- a/arch/arm/boot/dts/armada-385-linksys-cobra.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
+@@ -142,3 +142,205 @@
+ };
+ };
+ };
++
++&pcie1 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ AU =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <104 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <108 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <112 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <116 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <120 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <124 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <128 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <132 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <136 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <140 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <149 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <153 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <157 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <161 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <165 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>;
++ CA =
++ <36 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <40 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <44 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <48 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <165 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>;
++ CN =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <104 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <108 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <112 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <116 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <120 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <124 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <128 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <132 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <136 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <140 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <149 0 0x14 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <165 0 0x13 0x13 0x13 0x13 0x13 0x13 0x13 0x13 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>;
++ ETSI =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <104 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <108 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <112 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <116 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <120 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <124 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <128 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <132 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <136 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <140 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <149 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>;
++ FCC =
++ <36 0 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0 0xf>,
++ <40 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <44 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <48 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <165 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>;
++ };
++ };
++};
++
++&pcie2 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ AU =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ CA =
++ <1 0 0x17 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0xe 0xe 0xe 0xe 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x17 0x12 0x12 0x12 0x13 0x13 0x13 0x13 0xf 0xf 0xf 0xf 0x0 0x0 0x0 0x0 0 0xf>;
++ CN =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <14 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ ETSI =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ FCC =
++ <1 0 0x17 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0xe 0xe 0xe 0xe 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x17 0x12 0x12 0x12 0x13 0x13 0x13 0x13 0xf 0xf 0xf 0xf 0x0 0x0 0x0 0x0 0 0xf>;
++ };
++ };
++};
+--- a/arch/arm/boot/dts/armada-385-linksys-shelby.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-shelby.dts
+@@ -142,3 +142,205 @@
+ };
+ };
+ };
++
++&pcie1 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ AU =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <104 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <108 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <112 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <116 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <120 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <124 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <128 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <132 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <136 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <140 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <149 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <153 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <157 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <161 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>,
++ <165 0 0x19 0x19 0x19 0x17 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0x19 0x19 0x16 0x15 0 0xf>;
++ CA =
++ <36 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <40 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <44 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <48 0 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <165 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>;
++ CN =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <104 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <108 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <112 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <116 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <120 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <124 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <128 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <132 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <136 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <140 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <149 0 0x14 0x14 0x14 0x14 0x13 0x13 0x13 0x13 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>,
++ <165 0 0x13 0x13 0x13 0x13 0x13 0x13 0x13 0x13 0x14 0x14 0x14 0x14 0x10 0x10 0x10 0x10 0 0xf>;
++ ETSI =
++ <36 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <40 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <44 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <48 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <52 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <56 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <60 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <64 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <100 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <104 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <108 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <112 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <116 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <120 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <124 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <128 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <132 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <136 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <140 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>,
++ <149 0 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xd 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0xe 0 0xf>;
++ FCC =
++ <36 0 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0 0xf>,
++ <40 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <44 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <48 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0xf 0xf 0xf 0xf 0 0xf>,
++ <52 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <56 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <60 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <64 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <100 0 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <104 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x12 0x12 0x12 0x12 0x10 0x10 0x10 0x10 0 0xf>,
++ <108 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <112 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <116 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <120 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <124 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <128 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <132 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <136 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <140 0 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0 0xf>,
++ <149 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <153 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <157 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <161 0 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>,
++ <165 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0 0xf>;
++ };
++ };
++};
++
++&pcie2 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ AU =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ CA =
++ <1 0 0x17 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0xe 0xe 0xe 0xe 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x17 0x12 0x12 0x12 0x13 0x13 0x13 0x13 0xf 0xf 0xf 0xf 0x0 0x0 0x0 0x0 0 0xf>;
++ CN =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <14 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ ETSI =
++ <1 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0xa 0x0 0x0 0x0 0x0 0 0xf>;
++ FCC =
++ <1 0 0x17 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0xe 0xe 0xe 0xe 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x18 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x11 0x11 0x11 0x11 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x17 0x12 0x12 0x12 0x13 0x13 0x13 0x13 0xf 0xf 0xf 0xf 0x0 0x0 0x0 0x0 0 0xf>;
++ };
++ };
++};
+--- a/arch/arm/boot/dts/armada-385-linksys-rango.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-rango.dts
+@@ -157,6 +157,18 @@
+ };
+ };
+
++&pcie1 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ };
++};
++
++&pcie2 {
++ mwlwifi {
++ marvell,chainmask = <4 4>;
++ };
++};
++
+ &sdhci {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhci_pins>;
+--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
++++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+@@ -225,12 +225,100 @@
+ pcie at 2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
++
++ mwlwifi {
++ marvell,5ghz = <0>;
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ FCC =
++ <1 0 0x17 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0xf 0xf 0xf 0xf 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0x17 0x16 0x16 0x16 0x16 0x16 0x16 0x14 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0x17 0x11 0x11 0x11 0x11 0x11 0x11 0x11 0x10 0x10 0x10 0x10 0x0 0x0 0x0 0x0 0 0xf>;
++
++ ETSI =
++ <1 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <2 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <3 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <4 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <5 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <6 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <7 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <8 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <9 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <10 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <11 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <12 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>,
++ <13 0 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0xb 0x0 0x0 0x0 0x0 0 0xf>;
++ };
++ };
+ };
+
+ /* Second mini-PCIe port */
+ pcie at 3,0 {
+ /* Port 0, Lane 3 */
+ status = "okay";
++
++ mwlwifi {
++ marvell,2ghz = <0>;
++ marvell,chainmask = <4 4>;
++ marvell,powertable {
++ FCC =
++ <36 0 0x8 0x8 0x8 0x8 0x8 0x8 0x8 0x8 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <40 0 0x8 0x8 0x8 0x8 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <44 0 0x8 0x8 0x8 0x8 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <48 0 0x8 0x8 0x8 0x8 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0x9 0 0xf>,
++ <52 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0 0xf>,
++ <56 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0 0xf>,
++ <60 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0 0xf>,
++ <64 0 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0xf 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0x12 0 0xf>,
++ <100 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <104 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <108 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <112 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <116 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <120 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <124 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <128 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <132 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <136 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <140 0 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0x14 0 0xf>,
++ <149 0 0x16 0x16 0x16 0x16 0x14 0x14 0x14 0x14 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0 0xf>,
++ <153 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0 0xf>,
++ <157 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0 0xf>,
++ <161 0 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0 0xf>,
++ <165 0 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x16 0x15 0x15 0x15 0x15 0x14 0x14 0x14 0x14 0 0xf>;
++
++ ETSI =
++ <36 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <40 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <44 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <48 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <52 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <56 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <60 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <64 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <100 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <104 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <108 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <112 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <116 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <120 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <124 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <128 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <132 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <136 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <140 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>,
++ <149 0 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xc 0xd 0xd 0xd 0xd 0xc 0xc 0xc 0xc 0 0xf>;
++ };
++ };
+ };
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/303-linksys_hardcode_nand_ecc_settings.patch b/target/linux/mvebu/patches-5.10/303-linksys_hardcode_nand_ecc_settings.patch
new file mode 100644
index 0000000000..89a5e19803
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/303-linksys_hardcode_nand_ecc_settings.patch
@@ -0,0 +1,17 @@
+Newer Linksys boards might come with a Winbond W29N02GV which can be
+configured in different ways. Make sure we configure it the same way
+as the older chips so everything keeps working.
+
+Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
+
+--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
++++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
+@@ -148,6 +148,8 @@
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
++ nand-ecc-strength = <4>;
++ nand-ecc-step-size = <512>;
+ marvell,nand-keep-config;
+ nand-on-flash-bbt;
+ };
diff --git a/target/linux/mvebu/patches-5.10/304-revert_i2c_delay.patch b/target/linux/mvebu/patches-5.10/304-revert_i2c_delay.patch
new file mode 100644
index 0000000000..930c0f9494
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/304-revert_i2c_delay.patch
@@ -0,0 +1,15 @@
+--- a/arch/arm/boot/dts/armada-xp.dtsi
++++ b/arch/arm/boot/dts/armada-xp.dtsi
+@@ -237,12 +237,10 @@
+ };
+
+ &i2c0 {
+- compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x100>;
+ };
+
+ &i2c1 {
+- compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x100>;
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/305-armada-385-rd-mtd-partitions.patch b/target/linux/mvebu/patches-5.10/305-armada-385-rd-mtd-partitions.patch
new file mode 100644
index 0000000000..31bd53b1f3
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/305-armada-385-rd-mtd-partitions.patch
@@ -0,0 +1,19 @@
+--- a/arch/arm/boot/dts/armada-388-rd.dts
++++ b/arch/arm/boot/dts/armada-388-rd.dts
+@@ -103,6 +103,16 @@
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
++
++ partition at 0 {
++ label = "uboot";
++ reg = <0 0x400000>;
++ };
++
++ partition at 1 {
++ label = "firmware";
++ reg = <0x400000 0xc00000>;
++ };
+ };
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/306-ARM-mvebu-385-ap-Add-partitions.patch b/target/linux/mvebu/patches-5.10/306-ARM-mvebu-385-ap-Add-partitions.patch
new file mode 100644
index 0000000000..2057e31c7e
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/306-ARM-mvebu-385-ap-Add-partitions.patch
@@ -0,0 +1,35 @@
+From 9861f93a59142a3131870df2521eb2deb73026d7 Mon Sep 17 00:00:00 2001
+From: Maxime Ripard <maxime.ripard at free-electrons.com>
+Date: Tue, 13 Jan 2015 11:14:09 +0100
+Subject: [PATCH 2/2] ARM: mvebu: 385-ap: Add partitions
+
+Signed-off-by: Maxime Ripard <maxime.ripard at free-electrons.com>
+---
+ arch/arm/boot/dts/armada-385-db-ap.dts | 15 +++++++++++++++
+ 1 file changed, 15 insertions(+)
+
+--- a/arch/arm/boot/dts/armada-385-db-ap.dts
++++ b/arch/arm/boot/dts/armada-385-db-ap.dts
+@@ -218,19 +218,19 @@
+ #size-cells = <1>;
+
+ partition at 0 {
+- label = "U-Boot";
++ label = "u-boot";
+ reg = <0x00000000 0x00800000>;
+ read-only;
+ };
+
+ partition at 800000 {
+- label = "uImage";
++ label = "kernel";
+ reg = <0x00800000 0x00400000>;
+ read-only;
+ };
+
+ partition at c00000 {
+- label = "Root";
++ label = "ubi";
+ reg = <0x00c00000 0x3f400000>;
+ };
+ };
diff --git a/target/linux/mvebu/patches-5.10/307-armada-xp-linksys-mamba-broken-idle.patch b/target/linux/mvebu/patches-5.10/307-armada-xp-linksys-mamba-broken-idle.patch
new file mode 100644
index 0000000000..16112d53fc
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/307-armada-xp-linksys-mamba-broken-idle.patch
@@ -0,0 +1,10 @@
+--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
++++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+@@ -485,3 +485,7 @@
+ };
+ };
+ };
++
++&coherencyfab {
++ broken-idle;
++};
diff --git a/target/linux/mvebu/patches-5.10/308-armada-xp-linksys-mamba-wan.patch b/target/linux/mvebu/patches-5.10/308-armada-xp-linksys-mamba-wan.patch
new file mode 100644
index 0000000000..4315abc7d2
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/308-armada-xp-linksys-mamba-wan.patch
@@ -0,0 +1,11 @@
+--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
++++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+@@ -387,7 +387,7 @@
+
+ port at 4 {
+ reg = <4>;
+- label = "internet";
++ label = "wan";
+ };
+
+ port at 5 {
diff --git a/target/linux/mvebu/patches-5.10/309-linksys-status-led.patch b/target/linux/mvebu/patches-5.10/309-linksys-status-led.patch
new file mode 100644
index 0000000000..e5e83572c9
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/309-linksys-status-led.patch
@@ -0,0 +1,50 @@
+--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
++++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
+@@ -14,6 +14,13 @@
+ compatible = "linksys,armada385", "marvell,armada385",
+ "marvell,armada380";
+
++ aliases {
++ led-boot = &led_power;
++ led-failsafe = &led_power;
++ led-running = &led_power;
++ led-upgrade = &led_power;
++ };
++
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+@@ -71,7 +78,7 @@
+ pinctrl-0 = <&gpio_leds_pins>;
+ pinctrl-names = "default";
+
+- power {
++ led_power: power {
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
++++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+@@ -26,6 +26,13 @@
+ compatible = "linksys,mamba", "marvell,armadaxp-mv78230",
+ "marvell,armadaxp", "marvell,armada-370-xp";
+
++ aliases {
++ led-boot = &led_power;
++ led-failsafe = &led_power;
++ led-running = &led_power;
++ led-upgrade = &led_power;
++ };
++
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+@@ -197,7 +204,7 @@
+ pinctrl-0 = <&power_led_pin>;
+ pinctrl-names = "default";
+
+- power {
++ led_power: power {
+ label = "mamba:white:power";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
diff --git a/target/linux/mvebu/patches-5.10/310-linksys-use-eth0-as-cpu-port.patch b/target/linux/mvebu/patches-5.10/310-linksys-use-eth0-as-cpu-port.patch
new file mode 100644
index 0000000000..84d49a004b
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/310-linksys-use-eth0-as-cpu-port.patch
@@ -0,0 +1,25 @@
+--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
++++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
+@@ -116,7 +116,7 @@
+ };
+
+ ð2 {
+- status = "okay";
++ status = "disabled";
+ phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <2>;
+@@ -200,10 +200,10 @@
+ label = "wan";
+ };
+
+- port at 5 {
+- reg = <5>;
++ port at 6 {
++ reg = <6>;
+ label = "cpu";
+- ethernet = <ð2>;
++ ethernet = <ð0>;
+
+ fixed-link {
+ speed = <1000>;
diff --git a/target/linux/mvebu/patches-5.10/311-adjust-compatible-for-linksys.patch b/target/linux/mvebu/patches-5.10/311-adjust-compatible-for-linksys.patch
new file mode 100644
index 0000000000..a5d3e63810
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/311-adjust-compatible-for-linksys.patch
@@ -0,0 +1,68 @@
+--- a/arch/arm/boot/dts/armada-385-linksys-rango.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-rango.dts
+@@ -12,8 +12,8 @@
+
+ / {
+ model = "Linksys WRT3200ACM";
+- compatible = "linksys,rango", "linksys,armada385", "marvell,armada385",
+- "marvell,armada380";
++ compatible = "linksys,wrt3200acm", "linksys,rango", "linksys,armada385",
++ "marvell,armada385", "marvell,armada380";
+ };
+
+ &expander0 {
+--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
++++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+@@ -22,9 +22,10 @@
+ #include "armada-xp-mv78230.dtsi"
+
+ / {
+- model = "Linksys WRT1900AC";
+- compatible = "linksys,mamba", "marvell,armadaxp-mv78230",
+- "marvell,armadaxp", "marvell,armada-370-xp";
++ model = "Linksys WRT1900AC v1";
++ compatible = "linksys,wrt1900ac-v1", "linksys,mamba",
++ "marvell,armadaxp-mv78230", "marvell,armadaxp",
++ "marvell,armada-370-xp";
+
+ aliases {
+ led-boot = &led_power;
+--- a/arch/arm/boot/dts/armada-385-linksys-cobra.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-cobra.dts
+@@ -9,8 +9,9 @@
+ #include "armada-385-linksys.dtsi"
+
+ / {
+- model = "Linksys WRT1900ACv2";
+- compatible = "linksys,cobra", "linksys,armada385", "marvell,armada385",
++ model = "Linksys WRT1900AC v2";
++ compatible = "linksys,wrt1900ac-v2", "linksys,cobra",
++ "linksys,armada385", "marvell,armada385",
+ "marvell,armada380";
+ };
+
+--- a/arch/arm/boot/dts/armada-385-linksys-caiman.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-caiman.dts
+@@ -10,8 +10,8 @@
+
+ / {
+ model = "Linksys WRT1200AC";
+- compatible = "linksys,caiman", "linksys,armada385", "marvell,armada385",
+- "marvell,armada380";
++ compatible = "linksys,wrt1200ac", "linksys,caiman", "linksys,armada385",
++ "marvell,armada385", "marvell,armada380";
+ };
+
+ &expander0 {
+--- a/arch/arm/boot/dts/armada-385-linksys-shelby.dts
++++ b/arch/arm/boot/dts/armada-385-linksys-shelby.dts
+@@ -10,7 +10,8 @@
+
+ / {
+ model = "Linksys WRT1900ACS";
+- compatible = "linksys,shelby", "linksys,armada385", "marvell,armada385",
++ compatible = "linksys,wrt1900acs", "linksys,shelby",
++ "linksys,armada385", "marvell,armada385",
+ "marvell,armada380";
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/312-ARM-dts-armada388-clearfog-emmc-on-clearfog-base.patch b/target/linux/mvebu/patches-5.10/312-ARM-dts-armada388-clearfog-emmc-on-clearfog-base.patch
new file mode 100644
index 0000000000..dd2bef7f63
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/312-ARM-dts-armada388-clearfog-emmc-on-clearfog-base.patch
@@ -0,0 +1,87 @@
+From 8137da20701c776ad3481115305a5e8e410871ba Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at armlinux.org.uk>
+Date: Tue, 29 Nov 2016 10:15:45 +0000
+Subject: ARM: dts: armada388-clearfog: emmc on clearfog base
+
+Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
+---
+ arch/arm/boot/dts/armada-388-clearfog-base.dts | 1 +
+ .../dts/armada-38x-solidrun-microsom-emmc.dtsi | 62 ++++++++++++++++++++++
+ 2 files changed, 63 insertions(+)
+ create mode 100644 arch/arm/boot/dts/armada-38x-solidrun-microsom-emmc.dtsi
+
+--- a/arch/arm/boot/dts/armada-388-clearfog-base.dts
++++ b/arch/arm/boot/dts/armada-388-clearfog-base.dts
+@@ -7,6 +7,7 @@
+
+ /dts-v1/;
+ #include "armada-388-clearfog.dtsi"
++#include "armada-38x-solidrun-microsom-emmc.dtsi"
+
+ / {
+ model = "SolidRun Clearfog Base A1";
+--- /dev/null
++++ b/arch/arm/boot/dts/armada-38x-solidrun-microsom-emmc.dtsi
+@@ -0,0 +1,62 @@
++/*
++ * Device Tree file for SolidRun Armada 38x Microsom add-on for eMMC
++ *
++ * Copyright (C) 2015 Russell King
++ *
++ * This board is in development; the contents of this file work with
++ * the A1 rev 2.0 of the board, which does not represent final
++ * production board. Things will change, don't expect this file to
++ * remain compatible info the future.
++ *
++ * This file is dual-licensed: you can use it either under the terms
++ * of the GPL or the X11 license, at your option. Note that this dual
++ * licensing only applies to this file, and not this project as a
++ * whole.
++ *
++ * a) This file is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License
++ * version 2 as published by the Free Software Foundation.
++ *
++ * This file is distributed in the hope that it will be useful
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * Or, alternatively
++ *
++ * b) Permission is hereby granted, free of charge, to any person
++ * obtaining a copy of this software and associated documentation
++ * files (the "Software"), to deal in the Software without
++ * restriction, including without limitation the rights to use
++ * copy, modify, merge, publish, distribute, sublicense, and/or
++ * sell copies of the Software, and to permit persons to whom the
++ * Software is furnished to do so, subject to the following
++ * conditions:
++ *
++ * The above copyright notice and this permission notice shall be
++ * included in all copies or substantial portions of the Software.
++ *
++ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
++ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
++ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
++ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
++ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
++ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
++ * OTHER DEALINGS IN THE SOFTWARE.
++ */
++/ {
++ soc {
++ internal-regs {
++ sdhci at d8000 {
++ bus-width = <4>;
++ no-1-8-v;
++ non-removable;
++ pinctrl-0 = <µsom_sdhci_pins>;
++ pinctrl-names = "default";
++ status = "okay";
++ wp-inverted;
++ };
++ };
++ };
++};
diff --git a/target/linux/mvebu/patches-5.10/312-helios4-dts-status-led-alias.patch b/target/linux/mvebu/patches-5.10/312-helios4-dts-status-led-alias.patch
new file mode 100644
index 0000000000..4c4fbec764
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/312-helios4-dts-status-led-alias.patch
@@ -0,0 +1,28 @@
+--- a/arch/arm/boot/dts/armada-388-helios4.dts
++++ b/arch/arm/boot/dts/armada-388-helios4.dts
+@@ -15,6 +15,13 @@
+ model = "Helios4";
+ compatible = "kobol,helios4", "marvell,armada388",
+ "marvell,armada385", "marvell,armada380";
++
++ aliases {
++ led-boot = &led_status;
++ led-failsafe = &led_status;
++ led-running = &led_status;
++ led-upgrade = &led_status;
++ };
+
+ memory {
+ device_type = "memory";
+@@ -70,10 +77,9 @@
+
+ system-leds {
+ compatible = "gpio-leds";
+- status-led {
++ led_status: status-led {
+ label = "helios4:green:status";
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+- linux,default-trigger = "heartbeat";
+ default-state = "on";
+ };
+
diff --git a/target/linux/mvebu/patches-5.10/314-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch b/target/linux/mvebu/patches-5.10/314-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
new file mode 100644
index 0000000000..e989f59d5c
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/314-arm64-dts-marvell-armada37xx-Add-eth0-alias.patch
@@ -0,0 +1,20 @@
+From be893f672e340b56ca60f2f6c32fdd713a5852f5 Mon Sep 17 00:00:00 2001
+From: Kevin Mihelich <kevin at archlinuxarm.org>
+Date: Tue, 4 Jul 2017 19:25:28 -0600
+Subject: arm64: dts: marvell: armada37xx: Add eth0 alias
+
+Signed-off-by: Kevin Mihelich <kevin at archlinuxarm.org>
+---
+ arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
++++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+@@ -18,6 +18,7 @@
+ #size-cells = <2>;
+
+ aliases {
++ ethernet0 = ð0;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
diff --git a/target/linux/mvebu/patches-5.10/315-arm64-dts-marvell-armada-3720-espressobin-add-ports-.patch b/target/linux/mvebu/patches-5.10/315-arm64-dts-marvell-armada-3720-espressobin-add-ports-.patch
new file mode 100644
index 0000000000..a741e378d9
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/315-arm64-dts-marvell-armada-3720-espressobin-add-ports-.patch
@@ -0,0 +1,26 @@
+From 6ea9a1ee9367fb35acff1c08a0dc4213ff4687a0 Mon Sep 17 00:00:00 2001
+From: Tomasz Maciej Nowak <tmn505 at gmail.com>
+Date: Tue, 9 Apr 2019 15:53:42 +0200
+Subject: [PATCH] arm64: dts: marvell: armada-3720-espressobin: add ports
+ phandle
+
+Instead of referencing the whole mdio node, add ports phandle to adjust
+port labels in dts for different hardware iterations of ESPRESSObin
+boards.
+
+Signed-off-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
+---
+ arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+@@ -147,7 +147,7 @@
+
+ dsa,member = <0 0>;
+
+- ports {
++ ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
diff --git a/target/linux/mvebu/patches-5.10/316-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch b/target/linux/mvebu/patches-5.10/316-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch
new file mode 100644
index 0000000000..2240d0b39e
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/316-arm64-dts-uDPU-switch-PHY-operation-mode-to-2500base.patch
@@ -0,0 +1,34 @@
+Certain SFP modules (most notably Nokia GPON ones) first check
+connectivity on 1000base-x, and switch to 2500base-x afterwards. This
+is considered a quirk so the phylink switches the interface to
+2500base-x as well.
+
+However, after power-cycling the uDPU device, network interface/SFP module
+will not work correctly until the module is re-seated. This patch
+resolves this issue by forcing the interface to be brought up in
+2500base-x mode by default.
+
+Signed-off-by: Jakov Petrina <jakov.petrina at sartura.hr>
+Signed-off-by: Vladimir Vid <vladimir.vid at sartura.hr>
+Cc: Luka Perkov <luka.perkov at sartura.hr>
+
+--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
++++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+@@ -162,7 +162,7 @@
+ };
+
+ ð0 {
+- phy-mode = "sgmii";
++ phy-mode = "2500base-x";
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy1 0>;
+@@ -170,7 +170,7 @@
+ };
+
+ ð1 {
+- phy-mode = "sgmii";
++ phy-mode = "2500base-x";
+ status = "okay";
+ managed = "in-band-status";
+ phys = <&comphy0 1>;
diff --git a/target/linux/mvebu/patches-5.10/400-find_active_root.patch b/target/linux/mvebu/patches-5.10/400-find_active_root.patch
new file mode 100644
index 0000000000..854031b0d5
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/400-find_active_root.patch
@@ -0,0 +1,60 @@
+The WRT1900AC among other Linksys routers uses a dual-firmware layout.
+Dynamically rename the active partition to "ubi".
+
+Signed-off-by: Imre Kaloz <kaloz at openwrt.org>
+
+--- a/drivers/mtd/parsers/ofpart.c
++++ b/drivers/mtd/parsers/ofpart.c
+@@ -21,6 +21,8 @@ static bool node_has_compatible(struct d
+ return of_get_property(pp, "compatible", NULL);
+ }
+
++static int mangled_rootblock;
++
+ static int parse_fixed_partitions(struct mtd_info *master,
+ const struct mtd_partition **pparts,
+ struct mtd_part_parser_data *data)
+@@ -29,6 +31,7 @@ static int parse_fixed_partitions(struct
+ struct device_node *mtd_node;
+ struct device_node *ofpart_node;
+ const char *partname;
++ const char *owrtpart = "ubi";
+ struct device_node *pp;
+ int nr_parts, i, ret = 0;
+ bool dedicated = true;
+@@ -106,9 +109,13 @@ static int parse_fixed_partitions(struct
+ parts[i].size = of_read_number(reg + a_cells, s_cells);
+ parts[i].of_node = pp;
+
+- partname = of_get_property(pp, "label", &len);
+- if (!partname)
+- partname = of_get_property(pp, "name", &len);
++ if (mangled_rootblock && (i == mangled_rootblock)) {
++ partname = owrtpart;
++ } else {
++ partname = of_get_property(pp, "label", &len);
++ if (!partname)
++ partname = of_get_property(pp, "name", &len);
++ }
+ parts[i].name = partname;
+
+ if (of_get_property(pp, "read-only", &len))
+@@ -215,6 +222,18 @@ static int __init ofpart_parser_init(voi
+ return 0;
+ }
+
++static int __init active_root(char *str)
++{
++ get_option(&str, &mangled_rootblock);
++
++ if (!mangled_rootblock)
++ return 1;
++
++ return 1;
++}
++
++__setup("mangled_rootblock=", active_root);
++
+ static void __exit ofpart_parser_exit(void)
+ {
+ deregister_mtd_parser(&ofpart_parser);
diff --git a/target/linux/mvebu/patches-5.10/700-mvneta-tx-queue-workaround.patch b/target/linux/mvebu/patches-5.10/700-mvneta-tx-queue-workaround.patch
new file mode 100644
index 0000000000..a82a4c0d62
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/700-mvneta-tx-queue-workaround.patch
@@ -0,0 +1,34 @@
+The hardware queue scheduling is apparently configured with fixed
+priorities, which creates a nasty fairness issue where traffic from one
+CPU can starve traffic from all other CPUs.
+
+Work around this issue by forcing all tx packets to go through one CPU,
+until this issue is fixed properly.
+
+Signed-off-by: Felix Fietkau <nbd at nbd.name>
+---
+--- a/drivers/net/ethernet/marvell/mvneta.c
++++ b/drivers/net/ethernet/marvell/mvneta.c
+@@ -4684,6 +4684,14 @@ static int mvneta_ethtool_set_eee(struct
+ return phylink_ethtool_set_eee(pp->phylink, eee);
+ }
+
++static u16 mvneta_select_queue(struct net_device *dev, struct sk_buff *skb,
++ struct net_device *sb_dev)
++{
++ /* XXX: hardware queue scheduling is broken,
++ * use only one queue until it is fixed */
++ return 0;
++}
++
+ static const struct net_device_ops mvneta_netdev_ops = {
+ .ndo_open = mvneta_open,
+ .ndo_stop = mvneta_stop,
+@@ -4694,6 +4702,7 @@ static const struct net_device_ops mvnet
+ .ndo_fix_features = mvneta_fix_features,
+ .ndo_get_stats64 = mvneta_get_stats64,
+ .ndo_do_ioctl = mvneta_ioctl,
++ .ndo_select_queue = mvneta_select_queue,
+ .ndo_bpf = mvneta_xdp,
+ .ndo_xdp_xmit = mvneta_xdp_xmit,
+ };
diff --git a/target/linux/mvebu/patches-5.10/800-cpuidle-mvebu-indicate-failure-to-enter-deeper-sleep.patch b/target/linux/mvebu/patches-5.10/800-cpuidle-mvebu-indicate-failure-to-enter-deeper-sleep.patch
new file mode 100644
index 0000000000..29f36be460
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/800-cpuidle-mvebu-indicate-failure-to-enter-deeper-sleep.patch
@@ -0,0 +1,40 @@
+From c28b2d367da8a471482e6a4aa8337ab6369a80c2 Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at arm.linux.org.uk>
+Date: Sat, 3 Oct 2015 09:13:05 +0100
+Subject: cpuidle: mvebu: indicate failure to enter deeper sleep states
+
+The cpuidle ->enter method expects the return value to be the sleep
+state we entered. Returning negative numbers or other codes is not
+permissible since coupled CPU idle was merged.
+
+At least some of the mvebu_v7_cpu_suspend() implementations return the
+value from cpu_suspend(), which returns zero if the CPU vectors back
+into the kernel via cpu_resume() (the success case), or the non-zero
+return value of the suspend actor, or one (failure cases).
+
+We do not want to be returning the failure case value back to CPU idle
+as that indicates that we successfully entered one of the deeper idle
+states. Always return zero instead, indicating that we slept for the
+shortest amount of time.
+
+Signed-off-by: Russell King <rmk+kernel at arm.linux.org.uk>
+---
+ drivers/cpuidle/cpuidle-mvebu-v7.c | 6 +++++-
+ 1 file changed, 5 insertions(+), 1 deletion(-)
+
+--- a/drivers/cpuidle/cpuidle-mvebu-v7.c
++++ b/drivers/cpuidle/cpuidle-mvebu-v7.c
+@@ -39,8 +39,12 @@ static int mvebu_v7_enter_idle(struct cp
+ ret = mvebu_v7_cpu_suspend(deepidle);
+ cpu_pm_exit();
+
++ /*
++ * If we failed to enter the desired state, indicate that we
++ * slept lightly.
++ */
+ if (ret)
+- return ret;
++ return 0;
+
+ return index;
+ }
diff --git a/target/linux/mvebu/patches-5.10/801-pci-mvebu-time-out-reset-on-link-up.patch b/target/linux/mvebu/patches-5.10/801-pci-mvebu-time-out-reset-on-link-up.patch
new file mode 100644
index 0000000000..4058dc8ed5
--- /dev/null
+++ b/target/linux/mvebu/patches-5.10/801-pci-mvebu-time-out-reset-on-link-up.patch
@@ -0,0 +1,60 @@
+From 287b9df160b6159f8d385424904f8bac501280c1 Mon Sep 17 00:00:00 2001
+From: Russell King <rmk+kernel at armlinux.org.uk>
+Date: Sat, 9 Jul 2016 10:58:16 +0100
+Subject: pci: mvebu: time out reset on link up
+
+If the port reports that the link is up while we are resetting, there's
+little point in waiting for the full duration.
+
+Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
+---
+ drivers/pci/controller/pci-mvebu.c | 20 ++++++++++++++------
+ 1 file changed, 14 insertions(+), 6 deletions(-)
+
+--- a/drivers/pci/controller/pci-mvebu.c
++++ b/drivers/pci/controller/pci-mvebu.c
+@@ -928,6 +928,7 @@ static int mvebu_pcie_powerup(struct mve
+
+ if (port->reset_gpio) {
+ u32 reset_udelay = PCI_PM_D3COLD_WAIT * 1000;
++ unsigned int i;
+
+ of_property_read_u32(port->dn, "reset-delay-us",
+ &reset_udelay);
+@@ -935,7 +936,13 @@ static int mvebu_pcie_powerup(struct mve
+ udelay(100);
+
+ gpiod_set_value_cansleep(port->reset_gpio, 0);
+- msleep(reset_udelay / 1000);
++ for (i = 0; i < reset_udelay; i += 1000) {
++ if (mvebu_pcie_link_up(port))
++ break;
++ msleep(1);
++ }
++
++ printk("%s: reset completed in %dus\n", port->name, i);
+ }
+
+ return 0;
+@@ -1099,15 +1106,16 @@ static int mvebu_pcie_probe(struct platf
+ if (!child)
+ continue;
+
+- ret = mvebu_pcie_powerup(port);
+- if (ret < 0)
+- continue;
+-
+ port->base = mvebu_pcie_map_registers(pdev, child, port);
+ if (IS_ERR(port->base)) {
+ dev_err(dev, "%s: cannot map registers\n", port->name);
+ port->base = NULL;
+- mvebu_pcie_powerdown(port);
++ continue;
++ }
++
++ ret = mvebu_pcie_powerup(port);
++ if (ret < 0) {
++ port->base = NULL;
+ continue;
+ }
+
--
2.30.1
More information about the openwrt-devel
mailing list