[PATCH 19.07] ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1

Ernst Spielmann endspiel at disroot.org
Sat Jul 18 08:24:25 EDT 2020


Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel at disroot.org>
---
Backport commit c3dc52e39ac83704b7a376d8d5610bdb91807e3f
 .../ramips/base-files/etc/board.d/01_leds     |   6 ++
 .../ramips/base-files/etc/board.d/02_network  |   3 +
 .../ramips/dts/mt7628an_asus_rt-n10p-v3.dts   |  34 ++++++
 .../ramips/dts/mt7628an_asus_rt-n11p-b1.dts   |  34 ++++++
 .../ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts |  34 ++++++
 .../ramips/dts/mt7628an_asus_rt-n1x.dtsi      | 100 ++++++++++++++++++
 target/linux/ramips/image/mt76x8.mk           |  21 ++++
 7 files changed, 232 insertions(+)
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
 create mode 100644 target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 5c005db0c1..f040f53359 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -65,6 +65,12 @@ asl26555-16M)
 	ucidef_set_led_netdev "eth" "ETH" "asl26555:green:eth" "eth0"
 	set_wifi_led "asl26555:green:wlan"
 	;;
+asus,rt-n10p-v3|\
+asus,rt-n11p-b1|\
+asus,rt-n12-vp-b1)
+	ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0xf"
+	ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x10"
+	;;
 bdcom,wap2100-sk|\
 hiwifi,hc5861b)
 	set_wifi_led "$boardname:green:wlan2g"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index f743ce851a..ef18da0ef8 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -80,6 +80,9 @@ ramips_setup_interfaces()
 	3g-6200n|\
 	ai-br100|\
 	alfa-network,ac1200rm|\
+	asus,rt-n10p-v3|\
+	asus,rt-n11p-b1|\
+	asus,rt-n12-vp-b1|\
 	mediatek,ap-mt7621a-v60|\
 	xzwifi,creativebox-v1|\
 	d240|\
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
new file mode 100644
index 0000000000..ec00030cf2
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n10p-v3.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n10p-v3", "mediatek,mt7628an-soc";
+	model = "Asus RT-N10P V3";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n10p-v3:green:power";
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n10p-v3:green:wlan";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n10p-v3:green:wan";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n10p-v3:green:lan";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
new file mode 100644
index 0000000000..8aee2f73aa
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n11p-b1.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n11p-b1", "mediatek,mt7628an-soc";
+	model = "Asus RT-N11P B1";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n11p-b1:green:power";
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n11p-b1:green:wlan";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n11p-b1:green:wan";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n11p-b1:green:lan";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts b/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
new file mode 100644
index 0000000000..5a76ab4398
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n12-vp-b1.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "mt7628an_asus_rt-n1x.dtsi"
+
+/ {
+	compatible = "asus,rt-n12-vp-b1", "mediatek,mt7628an-soc";
+	model = "Asus RT-N12 VP B1";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "rt-n12-vp-b1:green:power";
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan {
+			label = "rt-n12-vp-b1:green:wlan";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wan {
+			label = "rt-n12-vp-b1:green:wan";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		lan {
+			label = "rt-n12-vp-b1:green:lan";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi b/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi
new file mode 100644
index 0000000000..1b21d3bca6
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_asus_rt-n1x.dtsi
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition at 30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition at 40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition at 50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0x7b0000>;
+			};
+		};
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0x4>;
+};
+
+&esw {
+	mediatek,portmap = <0x2f>;
+};
+
+&wmac {
+	status = "okay";
+};
+
+&state_default {
+	default {
+		ralink,groups = "i2c", "p0led_an", "p1led_an", "refclk", "wled_an";
+		ralink,function = "gpio";
+	};
+};
+
+&usbphy {
+	status = "disabled";
+};
+
+&ehci {
+	status = "disabled";
+};
+
+&ohci {
+	status = "disabled";
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 7df5c04297..74b62c6535 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -27,6 +27,27 @@ define Device/alfa-network_awusfree1
 endef
 TARGET_DEVICES += alfa-network_awusfree1
 
+define Device/asus_rt-n10p-v3
+  DTS := mt7628an_asus_rt-n10p-v3
+  IMAGE_SIZE := 7872k
+  DEVICE_TITLE := Asus RT-N10P V3
+endef
+TARGET_DEVICES += asus_rt-n10p-v3
+
+define Device/asus_rt-n11p-b1
+  DTS := mt7628an_asus_rt-n11p-b1
+  IMAGE_SIZE := 7872k
+  DEVICE_TITLE := Asus RT-N11P B1
+endef
+TARGET_DEVICES += asus_rt-n11p-b1
+
+define Device/asus_rt-n12-vp-b1
+  DTS := mt7628an_asus_rt-n12-vp-b1
+  IMAGE_SIZE := 7872k
+  DEVICE_TITLE := Asus RT-N12 VP B1
+endef
+TARGET_DEVICES += asus_rt-n12-vp-b1
+
 define Device/cudy_wr1000
   DTS := WR1000
   IMAGE_SIZE := $(ralink_default_fw_size_8M)
-- 
2.17.5




More information about the openwrt-devel mailing list