[OpenWrt-Devel] [PATCH 1/2] wireguard.sh: Batch file writes

Rosen Penev rosenp at gmail.com
Wed Jan 1 17:44:03 EST 2020


On Wed, Jan 1, 2020 at 3:31 AM Hartmut Knaack <knaack.h at gmx.de> wrote:
>
> Rosen Penev schrieb am 01.01.2020 um 03:08:
> > Speeds up config generation.
> >
> > Signed-off-by: Rosen Penev <rosenp at gmail.com>
> > ---
> >  .../utils/wireguard-tools/files/wireguard.sh  | 32 ++++++++-----------
> >  1 file changed, 14 insertions(+), 18 deletions(-)
> >
> > diff --git a/package/network/utils/wireguard-tools/files/wireguard.sh b/package/network/utils/wireguard-tools/files/wireguard.sh
> > index 4c811c6ba9..1e424e7959 100644
> > --- a/package/network/utils/wireguard-tools/files/wireguard.sh
> > +++ b/package/network/utils/wireguard-tools/files/wireguard.sh
> > @@ -42,13 +42,12 @@ proto_wireguard_setup_peer() {
> >       config_get endpoint_port "${peer_config}" "endpoint_port"
> >       config_get persistent_keepalive "${peer_config}" "persistent_keepalive"
> >
> > -     echo "[Peer]" >> "${wg_cfg}"
> > -     echo "PublicKey=${public_key}" >> "${wg_cfg}"
> > -     if [ "${preshared_key}" ]; then
> > -             echo "PresharedKey=${preshared_key}" >> "${wg_cfg}"
> > -     fi
> > +     {
> > +     echo "[Peer]"
> > +     echo "PublicKey=${public_key}"
> > +     [ "${preshared_key}" ] && echo "PresharedKey=${preshared_key}"
> >       for allowed_ip in $allowed_ips; do
> > -             echo "AllowedIPs=${allowed_ip}" >> "${wg_cfg}"
> > +             echo "AllowedIPs=${allowed_ip}"
> >       done
> >       if [ "${endpoint_host}" ]; then
> >               case "${endpoint_host}" in
> > @@ -64,11 +63,10 @@ proto_wireguard_setup_peer() {
> >               else
> >                       endpoint="${endpoint}:51820"
> >               fi
> > -             echo "Endpoint=${endpoint}" >> "${wg_cfg}"
> > -     fi
> > -     if [ "${persistent_keepalive}" ]; then
> > -             echo "PersistentKeepalive=${persistent_keepalive}" >> "${wg_cfg}"
> > +             echo "Endpoint=${endpoint}"
> >       fi
> > +     [ "${persistent_keepalive}" ] && echo "PersistentKeepalive=${persistent_keepalive}"
> > +     } >> "${wg_cfg}"
> >
>
> Hi,
> I would prefer to have the above code block indented, as well.
Sure. I did so initially as I felt it was too indented.
>
> >       if [ ${route_allowed_ips} -ne 0 ]; then
> >               for allowed_ip in ${allowed_ips}; do
> > @@ -119,14 +117,12 @@ proto_wireguard_setup() {
> >
> >       umask 077
> >       mkdir -p "${wg_dir}"
> > -     echo "[Interface]" > "${wg_cfg}"
> > -     echo "PrivateKey=${private_key}" >> "${wg_cfg}"
> > -     if [ "${listen_port}" ]; then
> > -             echo "ListenPort=${listen_port}" >> "${wg_cfg}"
> > -     fi
> > -     if [ "${fwmark}" ]; then
> > -             echo "FwMark=${fwmark}" >> "${wg_cfg}"
> > -     fi
> > +     {
> > +             echo "[Interface]"
> > +             echo "PrivateKey=${private_key}"
> > +             [ "${listen_port}" ] && echo "ListenPort=${listen_port}"
> > +             [ "${fwmark}" ] && echo "FwMark=${fwmark}"
> > +     } > "${wg_cfg}"
> >       config_foreach proto_wireguard_setup_peer "wireguard_${config}"
> >
> >       # apply configuration file
> >
>

_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list