[OpenWrt-Devel] ramips/mt7621 after 5.4 switch

Sergio Paracuellos sergio.paracuellos at gmail.com
Thu Apr 9 00:36:07 EDT 2020


Hi again,

On Thu, Apr 9, 2020 at 5:57 AM Sergio Paracuellos
<sergio.paracuellos at gmail.com> wrote:
>
> Hi Andre,
>
> On Wed, Apr 8, 2020 at 9:30 AM Sergio Paracuellos
> <sergio.paracuellos at gmail.com> wrote:
> >
> > Hi André,
> >
> >
> > On Wed, Apr 8, 2020 at 9:13 AM Andre Valentin <avalentin at marcant.net> wrote:
> > >
> > > Hi Sergio!
> > >
> > > Am 08.04.20 um 06:28 schrieb Sergio Paracuellos:
> > > > Hi Andre,
> > > >
> > > > On Tue, Apr 7, 2020 at 9:28 PM Andre Valentin <avalentin at marcant.net> wrote:
> > > >>
> > > >> Am 07.04.20 um 20:05 schrieb Sergio Paracuellos:
> > > >>> Hi,
> > > >>>
> > > >>> On Tue, Apr 7, 2020 at 12:16 PM Chuanhong Guo <gch981213 at gmail.com> wrote:
> > > >>>>
> > > >>>> [CC Sergio who worked on upstream PCIE driver]
> > > >>>>
> > > >>>> On Tue, Apr 7, 2020 at 4:45 PM Andre Valentin <avalentin at marcant.net> wrote:
> > > >>>>>
> > > >>>>> Hi!
> > > >>>>>
> > > >>>>> Currently I'm having some serious problems with the new 5.4 port.
> > > >>>>> 1) PCIe
> > > >>>>> I'm developing on the ZyXEL LTE3301-PLUS. It has PCIe and a mt7615e connected to second bus on the first phy.
> > > >>>>> If booting the device, kernel hangs with a RST message, telling the device is not detected. It seems the PCIe bus 1
> > > >>>>> cannot be reseted because nothing is connected to bus 0.
> > > >>>>> An upport of the old PCI driver reenables the function. I can provide more logs on this if needed.
> > > >>>
> > > >>> Logs and dmesg traces are always welcome and would be helpful. Both
> > > >>> working and not working traces.
> > > >>
> > > >> Of course, here we go with the old PCIe driver taken from 4.14 openwrt kernel:
> > > >> [    0.485729] pinctrl core: add 0 pinctrl maps
> > > >> [    0.485865] pull PCIe RST: RALINK_RSTCTRL = 4000000
> > > >> [    0.796015] release PCIe RST: RALINK_RSTCTRL = 7000000
> > > >> [    0.806088] ***** Xtal 40MHz *****
> > > >> [    0.812829] release PCIe RST: RALINK_RSTCTRL = 7000000
> > > >> [    0.823025] Port 0 N_FTS = 1b102800
> > > >> [    0.829933] Port 1 N_FTS = 1b105000
> > > >> [    0.836849] Port 2 N_FTS = 1b102800
> > > >> [    1.995991] PCIE0 no card, disable it(RST&CLK)
> > > >> [    2.004682] PCIE2 no card, disable it(RST&CLK)
> > > >> [    2.013495]  -> 20107f2
> > > >> [    2.018328] PCIE1 enabled
> > > >> [    2.023532] PCI host bridge /pcie at 1e140000 ranges:
> > > >> [    2.033045]  MEM 0x0000000060000000..0x000000006fffffff
> > > >> [    2.043401]   IO 0x000000001e160000..0x000000001e16ffff
> > > >> [    2.053762] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
> > > >> [    2.091056] PCI host bridge to bus 0000:00
> > > >> [    2.099131] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
> > > >> [    2.112734] pci_bus 0000:00: root bus resource [io  0xffffffff]
> > > >> [    2.124486] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
> > > >> [    2.137962] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
> > > >> [    2.153766] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
> > > >> [    2.165651] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
> > > >> [    2.178057] pci 0000:00:00.0: reg 0x14: [mem 0x60100000-0x6010ffff]
> > > >> [    2.190585] pci 0000:00:00.0: supports D1
> > > >> [    2.198439] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
> > > >> [    2.211463] random: fast init done
> > > >> [    2.211838] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
> > > >> [    2.230071] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
> > > >> [    2.243675] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
> > > >> [    2.272296] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
> > > >> [    2.285339] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
> > > >> [    2.298493] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
> > > >> [    2.311581] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
> > > >> [    2.325410] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
> > > >> [    2.338888] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
> > > >> [    2.352376] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
> > > >> [    2.366887] pci 0000:00:00.0: PCI bridge to [bus 01]
> > > >> [    2.376728] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
> > > >>
> > > >>
> > > >> And this is on 5.4 with the new driver with pcie0 status=disabled:
> > > >> [   30.464407] mt7621-pci 1e140000.pcie: GPIO lookup for consumer reset
> > > >> [   30.464415] mt7621-pci 1e140000.pcie: using device tree for GPIO lookup
> > > >> [   30.464474] mt7621-pci 1e140000.pcie: using lookup tables for GPIO lookup
> > > >> [   30.464484] mt7621-pci 1e140000.pcie: No GPIO consumer reset found
> > > >> [   30.664239] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
> > > >> [   30.678128] mt7621-pci 1e140000.pcie: Nothing is connected in virtual bridges. Exiting...
> > > >> booting goes on.
> > > >>
> > > >> And with pcie status=enabled:
> > > >> [   32.415863] rt2880-pinmux pinctrl: pcie is already enabled
> > > >> [   32.426821] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
> > > >> [   32.441900] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
> > > >> [   32.456880] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
> > > >> [   32.571556] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> > > >> [   32.582680] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
> > > >> [   32.693592] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
> > > >> hangs.
> > > >
> > > > I think the problem here is that upstream driver use two phy's nodes
> > > > with pcie-phy0 being a dual ported one.
> > > > Because there is nothing connected in pcie0 the phy is just stopped
> > > > assuming nothing will be connected also in pcie1.
> > > > Just to see if that is the problem, can you please patch the
> > > > 'mt7621_pcie_init_ports' function and comment the following piece of
> > > > code:
> > > >
> > > > if (slot != 1)
> > > >      phy_power_off(port->phy);
> > > >
> > > > Let's see what happens.
> > >
> > > Hmm, that did the trick:
> > > [   30.444228] rt2880-pinmux pinctrl: found group selector 6 for pcie
> > > [   30.444249] rt2880-pinmux pinctrl: request pin 19 (io19) for 1e140000.pcie
> > > [   30.444396] mt7621-pci 1e140000.pcie: Parsing DT failed
> > > [   32.403940] rt2880-pinmux pinctrl: found group selector 6 for pcie
> > > [   32.403963] rt2880-pinmux pinctrl: request pin 19 (io19) for 1e140000.pcie
> > > [   32.403977] rt2880-pinmux pinctrl: pcie is already enabled
> > > [   32.414931] mt7621-pci 1e140000.pcie: Error applying setting, reverse things back
> > > [   32.430012] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
> > > [   32.444754] mt7621-pci 1e140000.pcie: GPIO lookup for consumer reset
> > > [   32.444763] mt7621-pci 1e140000.pcie: using device tree for GPIO lookup
> > > [   32.444811] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/pcie at 1e140000[0]' - status (0)
> > > [   32.444875] mt7621-pci 1e140000.pcie: GPIO lookup for consumer reset
> > > [   32.444883] mt7621-pci 1e140000.pcie: using device tree for GPIO lookup
> > > [   32.444906] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/pcie at 1e140000[1]'
> > > [   32.444924] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/pcie at 1e140000[1]'
> > > [   32.444935] mt7621-pci 1e140000.pcie: using lookup tables for GPIO lookup
> > > [   32.444945] mt7621-pci 1e140000.pcie: No GPIO consumer reset found
> > > [   32.445011] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
> > > [   32.459753] mt7621-pci 1e140000.pcie: GPIO lookup for consumer reset
> > > [   32.459761] mt7621-pci 1e140000.pcie: using device tree for GPIO lookup
> > > [   32.459791] of_get_named_gpiod_flags: can't parse 'reset-gpios' property of node '/pcie at 1e140000[2]'
> > > [   32.459808] of_get_named_gpiod_flags: can't parse 'reset-gpio' property of node '/pcie at 1e140000[2]'
> > > [   32.459818] mt7621-pci 1e140000.pcie: using lookup tables for GPIO lookup
> > > [   32.459826] mt7621-pci 1e140000.pcie: No GPIO consumer reset found
> > > [   32.559695] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
> > > [   32.570819] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
> > > [   32.681732] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
> > > [   32.695603] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
> > > [   32.709477] mt7621-pci 1e140000.pcie: PCIE1 enabled
> > > [   32.719207] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
> > > [   32.737964] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
> > > [   32.750653] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
> > > [   32.764358] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
> > > [   32.778073] pci_bus 0000:00: root bus resource [bus 00-ff]
> > > [   32.789053] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
> > > [   32.801064] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
> > > [   32.813561] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
> > > [   32.826152] pci 0000:00:00.0: supports D1
> > > [   32.834144] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
> > > [   32.846953] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
> > > [   32.863173] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
> > > [   32.875209] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
> > > [   32.888911] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
> > > [   32.917782] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
> > > [   32.928208] pci 0000:00:00.0:   bridge window [io  0x0000-0x0fff]
> > > [   32.940355] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff]
> > > [   32.953890] pci 0000:00:00.0:   bridge window [mem 0x00000000-0x000fffff pref]
> > > [   32.968289] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
> > > [   32.981535] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
> > > [   32.994721] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
> > > [   33.008598] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
> > > [   33.022134] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
> > > [   33.036535] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
> > > [   33.050082] pci 0000:00:00.0: BAR 7: assigned [io  0x1e160000-0x1e160fff]
> > > [   33.063622] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
> > > [   33.078208] pci 0000:00:00.0: PCI bridge to [bus 01]
> > > [   33.088106] pci 0000:00:00.0:   bridge window [io  0x1e160000-0x1e160fff]
> > > [   33.101640] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
> > > [   33.115169] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
> > > [   45.990931] pci 0000:00:00.0: enabling device (0004 -> 0007)
> > >
> > >
> > > It works, yeah! But what now? Do you fix the driver? When I can help/test ..
>
> Does something like this working also for you?
>
> diff --git a/drivers/staging/mt7621-pci/pci-mt7621.c
> b/drivers/staging/mt7621-pci/pci-mt7621.c
> index f58e3a51fc71..b73fe1364701 100644
> --- a/drivers/staging/mt7621-pci/pci-mt7621.c
> +++ b/drivers/staging/mt7621-pci/pci-mt7621.c
> @@ -508,12 +508,18 @@ static void mt7621_pcie_init_ports(struct
> mt7621_pcie *pcie)
>                 if (!mt7621_pcie_port_is_linkup(port)) {
>                         dev_err(dev, "pcie%d no card, disable it (RST & CLK)\n",
>                                 slot);
> -                       if (slot != 1)
> -                               phy_power_off(port->phy);
>                         mt7621_control_assert(port);
>                         mt7621_pcie_port_clk_disable(port);
>                         port->enabled = false;
> +
> +                       if (slot == 0)
> +                               continue;
> +
> +                       if (slot == 1 && !tmp->enabled)
> +                               phy_power_off(port->phy);
                                                            ^^^^^^
                                                            This
should be tmp->phy
> +
>                 }
> +               tmp = port;
>         }
>  }

Thanks,
     Sergio Paracuellos
>
>
> Thanks,
>     Sergio Paracuellos
>
> > >
> >
> > Best regards,
> >     Sergio Paracuellos

_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list