[OpenWrt-Devel] [PATCH v2] ath79: add support for Netgear WNR2200

John Crispin john at phrozen.org
Thu Oct 31 08:48:06 EDT 2019


On 30/10/2019 10:07, Michal Cieslakiewicz wrote:
> This patch adds ath79 support for Netgear WNR2200.
> Router was previously supported by ar71xx target only (8 MiB variant).
> Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
> 16 MiB for Russia and China markets. Apart from flash size both variants
> share the same hardware specification.
> 
> Specification
> =============
>    * Description: Netgear WNR2200
>    * Loader: U-boot
>    * SOC: Atheros AR7241 (360 MHz)
>    * RAM: 64 MiB
>    * Flash: 8 MiB or 16 MiB (SPI NOR)
> 	- U-boot binary: 256 KiB
> 	- U-boot environment: 64 KiB
> 	- Firmware: 7808 KiB or 16000 KiB
> 	- ART: 64 KiB
>    * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
>    * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
>    * USB: yes, 1 x USB 2.0
>    * Buttons:
> 	- Reset
> 	- WiFi (rfkill)
> 	- WPS
>    * LEDs:
> 	- Power (amber/green)
> 	- WAN (amber/green)
> 	- WLAN (blue)
> 	- 4 x LAN (amber/green)
> 	- WPS (green)
>    * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
>    * Power supply: DC 12V 1.5A
>    * MAC addresses: LAN on case label, WAN +1, WLAN +2
> 
> Installation
> ============
>    * TFTP recovery
>    * TFTP via U-boot prompt
>    * sysupgrade
>    * Web interface
> 
> Test build configuration
> ========================
> CONFIG_TARGET_ath79=y
> CONFIG_TARGET_ath79_generic=y
> CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
> CONFIG_ALL_KMODS=y
> CONFIG_DEVEL=y
> CONFIG_CCACHE=y
> CONFIG_COLLECT_KERNEL_DEBUG=y
> CONFIG_IMAGEOPT=y
> CONFIG_KERNEL_DEBUG_INFO=y
> CONFIG_KERNEL_DEBUG_KERNEL=y
> 


Hi,
sorry for the foo, patch fails to apply, kindly rebase/resend it
	John




> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz at wp.pl>
> ---
>   package/boot/uboot-envtools/files/ath79       |   2 +
>   .../ath79/dts/ar7241_netgear_wnr2200-16m.dts  |  34 +++
>   .../ath79/dts/ar7241_netgear_wnr2200-8m.dts   |  34 +++
>   .../ath79/dts/ar7241_netgear_wnr2200.dtsi     | 207 ++++++++++++++++++
>   .../generic/base-files/etc/board.d/01_leds    |  12 +
>   .../generic/base-files/etc/board.d/02_network |   6 +
>   .../etc/hotplug.d/firmware/10-ath9k-eeprom    |   2 +
>   target/linux/ath79/image/generic.mk           |  34 +++
>   8 files changed, 331 insertions(+)
>   create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
>   create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
>   create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
> 
> diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
> index d5b94823fd..cc9741cedf 100644
> --- a/package/boot/uboot-envtools/files/ath79
> +++ b/package/boot/uboot-envtools/files/ath79
> @@ -22,6 +22,8 @@ glinet,gl-ar300m-nor|\
>   librerouter,librerouter-v1|\
>   netgear,ex6400|\
>   netgear,ex7300|\
> +netgear,wnr2200-8m|\
> +netgear,wnr2200-16m|\
>   ocedo,koala|\
>   ocedo,raccoon|\
>   openmesh,om5p-ac-v2|\
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
> new file mode 100644
> index 0000000000..d182b58c05
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "ar7241_netgear_wnr2200.dtsi"
> +
> +/ {
> +	compatible = "netgear,wnr2200-16m", "qca,ar7241";
> +	model = "Netgear WNR2200 (16M)";
> +};
> +
> +&partitions {
> +	partition at 0 {
> +		label = "u-boot";
> +		reg = <0x0 0x40000>;
> +		read-only;
> +	};
> +
> +	partition at 40000 {
> +		label = "u-boot-env";
> +		reg = <0x40000 0x10000>;
> +	};
> +
> +	partition at 50000 {
> +		label = "firmware";
> +		reg = <0x50000 0xfa0000>;
> +		compatible = "netgear,uimage";
> +	};
> +
> +	art: partition at ff0000 {
> +		label = "art";
> +		reg = <0xff0000 0x10000>;
> +		read-only;
> +	};
> +};
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
> new file mode 100644
> index 0000000000..e926c17893
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts
> @@ -0,0 +1,34 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include "ar7241_netgear_wnr2200.dtsi"
> +
> +/ {
> +	compatible = "netgear,wnr2200-8m", "qca,ar7241";
> +	model = "Netgear WNR2200 (8M)";
> +};
> +
> +&partitions {
> +	partition at 0 {
> +		label = "u-boot";
> +		reg = <0x0 0x40000>;
> +		read-only;
> +	};
> +
> +	partition at 40000 {
> +		label = "u-boot-env";
> +		reg = <0x40000 0x10000>;
> +	};
> +
> +	partition at 50000 {
> +		label = "firmware";
> +		reg = <0x50000 0x7a0000>;
> +		compatible = "netgear,uimage";
> +	};
> +
> +	art: partition at 7f0000 {
> +		label = "art";
> +		reg = <0x7f0000 0x10000>;
> +		read-only;
> +	};
> +};
> diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
> new file mode 100644
> index 0000000000..1ce4d11835
> --- /dev/null
> +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi
> @@ -0,0 +1,207 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +#include "ar7241.dtsi"
> +
> +/ {
> +	chosen {
> +		bootargs = "console=ttyS0,115200n8";
> +	};
> +
> +	aliases {
> +		led-boot = &power_amber;
> +		led-failsafe = &power_amber;
> +		led-running = &power_green;
> +		led-upgrade = &power_amber;
> +		label-mac-device = &eth1;
> +	};
> +
> +	ath9k-keys {
> +		compatible = "gpio-keys-polled";
> +		poll-interval = <20>;
> +
> +		wps {
> +			label = "wps";
> +			linux,code = <KEY_WPS_BUTTON>;
> +			gpios = <&ath9k 5 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <60>;
> +		};
> +
> +		reset {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&ath9k 6 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <60>;
> +		};
> +
> +		rfkill {
> +			label = "rfkill";
> +			linux,code = <KEY_RFKILL>;
> +			gpios = <&ath9k 3 GPIO_ACTIVE_LOW>;
> +			debounce-interval = <60>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>;
> +
> +		wan_green {
> +			label = "netgear:green:wan";
> +			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wan_amber {
> +			label = "netgear:amber:wan";
> +			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan1_green {
> +			label = "netgear:green:lan1";
> +			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan1_amber {
> +			label = "netgear:amber:lan1";
> +			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan2_green {
> +			label = "netgear:green:lan2";
> +			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan2_amber {
> +			label = "netgear:amber:lan2";
> +			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan3_green {
> +			label = "netgear:green:lan3";
> +			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan3_amber {
> +			label = "netgear:amber:lan3";
> +			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan4_green {
> +			label = "netgear:green:lan4";
> +			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		lan4_amber {
> +			label = "netgear:amber:lan4";
> +			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		wps_green {
> +			label = "netgear:green:wps";
> +			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		usb_green {
> +			label = "netgear:green:usb";
> +			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
> +			trigger-sources = <&hub_port>;
> +			linux,default-trigger = "usbport";
> +		};
> +	};
> +
> +	ath9k-leds {
> +		compatible = "gpio-leds";
> +
> +		power_green: power_green {
> +			label = "netgear:green:power";
> +			gpios = <&ath9k 2 GPIO_ACTIVE_LOW>;
> +		};
> +
> +		power_amber: power_amber {
> +			label = "netgear:amber:power";
> +			gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
> +			default-state = "keep";
> +		};
> +
> +		wlan_blue {
> +			label = "netgear:blue:wlan";
> +			gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "phy0tpt";
> +		};
> +	};
> +};
> +
> +&spi {
> +	status = "okay";
> +	num-cs = <1>;
> +
> +	flash at 0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <25000000>;
> +
> +		partitions: partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +		};
> +	};
> +};
> +
> +&eth0 {
> +	status = "okay";
> +
> +	mtd-mac-address = <&art 0x0>;
> +};
> +
> +&eth1 {
> +	status = "okay";
> +
> +	compatible = "qca,ar7241-eth", "syscon", "simple-mfd";
> +	mtd-mac-address = <&art 0x6>;
> +};
> +
> +&pcie {
> +	status = "okay";
> +
> +	ath9k: wifi at 0,0 {
> +		compatible = "pci168c,002e";
> +		reg = <0x0000 0 0 0 0>;
> +		mtd-mac-address = <&art 0x0>;
> +		mtd-mac-address-increment = <1>;
> +		qca,no-eeprom;
> +		#gpio-cells = <2>;
> +		gpio-controller;
> +
> +		usb_power {
> +			gpio-hog;
> +			line-name = "netgear:power:usb";
> +			gpios = <4 GPIO_ACTIVE_HIGH>;
> +			output-high;
> +		};
> +	};
> +};
> +
> +&uart {
> +	status = "okay";
> +};
> +
> +&usb_phy {
> +	status = "okay";
> +};
> +
> +&usb {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	hub_port: port at 1 {
> +		reg = <1>;
> +		#trigger-source-cells = <0>;
> +	};
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index e3575ff041..441091de32 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -103,6 +103,18 @@ glinet,gl-ar300m-lite)
>   glinet,gl-x750)
>   	ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1"
>   	;;
> +netgear,wnr2200-8m|\
> +netgear,wnr2200-16m)
> +	ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0"
> +	ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04"
> +	ucidef_set_led_switch "lan2green" "LAN2 (green)" "netgear:green:lan2" "switch0" "0x04" "0x04"
> +	ucidef_set_led_switch "lan3green" "LAN3 (green)" "netgear:green:lan3" "switch0" "0x08" "0x04"
> +	ucidef_set_led_switch "lan4green" "LAN4 (green)" "netgear:green:lan4" "switch0" "0x10" "0x04"
> +	ucidef_set_led_switch "lan1amber" "LAN1 (amber)" "netgear:amber:lan1" "switch0" "0x02" "0x02"
> +	ucidef_set_led_switch "lan2amber" "LAN2 (amber)" "netgear:amber:lan2" "switch0" "0x04" "0x02"
> +	ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "netgear:amber:lan3" "switch0" "0x08" "0x02"
> +	ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "netgear:amber:lan4" "switch0" "0x10" "0x02"
> +	;;
>   pcs,cap324)
>   	ucidef_set_led_netdev "lan" "LAN" "pcs:lan:green" "eth0"
>   	;;
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index 90f622b262..0cf411041d 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -184,6 +184,12 @@ ath79_setup_interfaces()
>   		ucidef_add_switch_port_attr "switch0" 2 led 9
>   		ucidef_add_switch_port_attr "switch0" 5 led 2
>   		;;
> +	netgear,wnr2200-8m|\
> +	netgear,wnr2200-16m)
> +		ucidef_set_interface_wan "eth0"
> +		ucidef_add_switch "switch0" \
> +			"0 at eth1" "1:lan" "2:lan" "3:lan" "4:lan"
> +		;;
>   	phicomm,k2t)
>   		ucidef_add_switch "switch0" \
>   			"0 at eth0" "3:lan:1" "5:lan:2" "4:wan"
> diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> index 4b07660f02..6a6484879a 100644
> --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
> @@ -76,6 +76,8 @@ case "$FIRMWARE" in
>   	winchannel,wb2000)
>   		caldata_extract "art" 0x5000 0x440
>   		;;
> +	netgear,wnr2200-8m|\
> +	netgear,wnr2200-16m|\
>   	pcs,cap324|\
>   	tplink,tl-wr2543-v1|\
>   	tplink,tl-wr842n-v1|\
> diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
> index cea903f253..70631c20d0 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -794,6 +794,40 @@ define Device/netgear_wndr3800ch
>   endef
>   TARGET_DEVICES += netgear_wndr3800ch
>   
> +define Device/netgear_wnr2200_common
> +  ATH_SOC := ar7241
> +  DEVICE_MODEL := WNR2200
> +  DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport
> +  NETGEAR_KERNEL_MAGIC := 0x32323030
> +  NETGEAR_BOARD_ID := wnr2200
> +  IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | \
> +	append-rootfs | pad-rootfs
> +  $(Device/netgear_ath79)
> +endef
> +
> +define Device/netgear_wnr2200-8m
> +  $(Device/netgear_wnr2200_common)
> +  DEVICE_VARIANT := 8M
> +  NETGEAR_HW_ID := 29763600+08+64
> +  IMAGE_SIZE := 7808k
> +  IMAGES += factory-NA.img
> +  IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \
> +	check-size $$$$(IMAGE_SIZE)
> +  SUPPORTED_DEVICES += wnr2200
> +endef
> +TARGET_DEVICES += netgear_wnr2200-8m
> +
> +define Device/netgear_wnr2200-16m
> +  $(Device/netgear_wnr2200_common)
> +  DEVICE_VARIANT := 16M
> +  DEVICE_ALT0_VENDOR := NETGEAR
> +  DEVICE_ALT0_MODEL := WNR2200
> +  DEVICE_ALT0_VARIANT := CN/RU
> +  NETGEAR_HW_ID :=
> +  IMAGE_SIZE := 16000k
> +endef
> +TARGET_DEVICES += netgear_wnr2200-16m
> +
>   define Device/ocedo_koala
>     ATH_SOC := qca9558
>     DEVICE_VENDOR := Ocedo
> 


_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list