[OpenWrt-Devel] [PATCH] Support for Edimax EW-7476RPC / EW-7478AC

Daniel Golle daniel at makrotopia.org
Mon May 27 09:35:31 PDT 2019


Hi Birger,

thanks for submitting your work. In order to support the external
switch, existing generic features should be used in order to
implement the phy-reset via GPIO#39.
See my comments in the code (I commented the first device only, same
applies to the 2nd device as well).

On Mon, May 27, 2019 at 05:55:24PM +0200, Birger Koblitz wrote:
> ramips: add Netgear EW-7476RPC
> 
> SoC:   MediaTek MT7620a @ 580MHz
> RAM:   64M (Winbond W9751G6KB-25)
> FLASH: 8MB (Macronix)
> WiFi:  SoC-integrated: MediaTek MT76620a bgn

Typo, I supposed. MT7620a (or RT6352 to name the embedded WiFi IP)

> WiFi:  MediaTek MT7612EN nac
> GBE:   RTL8211E

Please mention how many phyical ports the device got and if all of
them support GbE.

> BTN:   WPS - RFKILL/RF 50%/RF 100% toggle
> LED:    - Wifi 5g (blue)
>         - Wifi 2g (blue)
>         - Crossband (green)
>         - Power (green)
>         - WPS (green)
>         - LAN (Green)
> UART:  UART is present as Pads with throughholes on the PCB. They are
>        located next to the switch for the wifi configuration
>        3.3V - RX - GND - TX / 57600-8N1
>        3.3V is the square pad
> 
> Installation
> ------------
> Update the factory image via the web-interfaces (by default:
> 192.168.9.2/24).
> http://192.168.9.2/index.asp
> 
> ramips: add Netgear EW-7478AC
> 
> SoC:   MediaTek MT7620a @ 580MHz
> RAM:   64M (Winbond W9751G6KB-25)
> FLASH: 8MB (Macronix)
> WiFi:  SoC-integrated: MediaTek MT76620a bgn
Same here

> WiFi:  MediaTek MT7612EN nac
> GBE:   RTL8211E
> BTN:   WPS - RFKILL/RF 50%/RF 100% toggle
> LED:    - Wifi 5g (blue)
>         - Wifi 2g (blue)
>         - Crossband (green)
>         - Power (green)
>         - WPS (green)
>         - LAN (Green)
> UART:  UART is present as Pads with throughholes on the PCB. They are
>        located next to the switch for the wifi configuration
>        3.3V - RX - GND - TX / 57600-8N1
>        3.3V is the square pad
> 
> Installation
> ------------
> Update the factory image via the web-interfaces (by default:
> http://edimaxext.setup)
> Or push wpa button on power on and send firmware via tftp to 192.168.1.6
> 
> The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
> antennas it has 2 external ones.
> 
> 
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index b55ca0413e..78e93b557b 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -146,6 +146,10 @@ dir-860l-b1)
>  edimax,br-6478ac-v2)
>         set_wifi_led "$boardname:blue:wlan"
>         ;;
> +edimax,ew-7476rpc|\
> +edimax,ew-7478ac)
> +        ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" 
> "switch0" "0x20"
> +        ;;
>  ex2700|\
>  wn3000rpv3)
>         set_wifi_led "$boardname:green:router"
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index 2e56678cf5..bbdfe9b128 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -50,6 +50,8 @@ ramips_setup_interfaces()
>         broadway|\
>         dcs-930|\
>         dcs-930l-b1|\
> +       edimax,ew-7476rpc|\
> +       edimax,ew-7478ac|\
>         ht-tm02|\
>         kimax,u35wf|\
>         linkits7688 | \
> diff --git a/target/linux/ramips/dts/EW-7476RPC.dts
> b/target/linux/ramips/dts/EW-7476RPC.dts
> new file mode 100644
> index 0000000000..7a1edf3e4d
> --- /dev/null
> +++ b/target/linux/ramips/dts/EW-7476RPC.dts
> @@ -0,0 +1,238 @@
> +/*
> + * Device Tree file for the Edimax EW-7476RPC
> + * based on Edimax BR-6478AC V2
> + *
> + * Copyright (C) 2016 Rohan Murch <rohan.murch at gmail.com>
> + * Copyright (C) 2016 Hans Ulli Kroll <ulli.kroll at googlemail.com>
> + * Copyright (C) 2017 James McKenzie <openwrt at madingley.org>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2.  This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> +
> + The following definitions were found in the orignal GPL firmware source
> + HW_LED_WIRELESS_ABAND_="71"
> + HW_LED_WIRELESS_GBAND_="70"
> + HW_LED_WIRELES_="69"
> + HW_LED_POWER_="67"
> + HW_LED_WPS_="68"
> + HW_LED_LAN_="66"
> + HW_BUTTON_APSWITCH_BUT_1_="62"
> + HW_BUTTON_APSWITCH_BUT_2_="63"
> + HW_BUTTON_RESET_="60"
> +
> + The device does not have a reset button (but there are solder pads for
> a button), WPS and reset are swapped.
> +
> + */
> +
> +/dts-v1/;
> +
> +#include "mt7620a.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +       compatible = "edimax,ew-7476rpc", "ralink,mt7620a-soc";
> +       model = "Edimax EW-7476RPC";
> +
> +       aliases {
> +               led-boot = &led_power;
> +               led-failsafe = &led_power;
> +               led-running = &led_power;
> +               led-upgrade = &led_power;
> +       };
> +
> +       chosen {
> +               bootargs = "console=ttyS0,57600";
> +       };
> +
> +
> +       keys {
> +                compatible = "gpio-keys";
> +
> +                reset_wps {
> +                        label = "reset_wps";
> +                        gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
> +                        linux,code = <KEY_RESTART>;
> +                };
> +               switch_high {
> +                       label = "switch high";
> +                       gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
> +                       linux,code = <BTN_0>;
> +                       linux,input-type = <EV_SW>;
> +               };
> +               switch_off {
> +                       label = "switch off";
> +                       gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
> +                       linux,code = <BTN_1>;
> +                       linux,input-type = <EV_SW>;
> +               };
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               led_power: power {
> +                       label = "ew-7476rpc:green:power";
> +                       gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
> +               };
> +               lan {
> +                       label = "ew-7476rpc:green:lan";
> +                       gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
> +               };
> +               wlan2g {
> +                       label = "ew-7476rpc:blue:wlan2g";
> +                       gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
> +                       linux,default-trigger = "phy1radio";
> +               };
> +               wlan5g {
> +                       label = "ew-7476rpc:blue:wlan5g";
> +                       gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
> +                       linux,default-trigger = "phy0radio";
> +               };
> +               wps {
> +                       label = "ew-7476rpc:green:wps";
> +                       gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
> +               };
> +               crossband {
> +                       label = "ew-7476rpc:green:crossband";
> +                       gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
> +               };
> +       };
> +};
> +
> +
> +&gpio2 {
> +       status = "okay";
> +};
> +
> +&spi0 {
> +       status = "okay";
> +
> +       flash at 0 {
> +               compatible = "jedec,spi-nor";
> +               reg = <0 0>;
> +               spi-max-frequency = <10000000>;
> +
> +               partitions {
> +                       compatible = "fixed-partitions";
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +
> +                       partition at 0 {
> +                               label = "u-boot";
> +                               reg = <0x0 0x30000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 30000 {
> +                               label = "u-boot-env";
> +                               reg = <0x30000 0x10000>;
> +                               read-only;
> +                       };
> +
> +                       factory: partition at 40000 {
> +                               label = "factory";
> +                               reg = <0x40000 0x10000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 50000 {
> +                               label = "cimage";
> +                               reg = <0x50000 0x20000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 70000 {
> +                               compatible = "edimax,uimage";
> +                               label = "firmware";
> +                               reg = <0x00070000 0x00790000>;
> +                       };
> +               };
> +       };
> +};
> +
> +&pinctrl {
> +       state_default: pinctrl0 {
> +               gpio {
> +            // might need pin 39: ;
> +                       ralink,group = "i2c", "uartf", "nd_sd",
> "rgmii2", "spi refclk";
> +                       ralink,function = "gpio";
> +               };
> +       };
> +};

A pinctrl group for the switch reset would be appropriate:
GPIO 39 is p4led_an, hence add:
	phy_reset_pins: phy-reset {
		gpio {
			ralink,group = "p4led_an";
			ralink,function = "gpio";
		};
	};

> +
> +
> +&ethernet {
> +
> +    status = "okay";
> +       mtd-mac-address = <&factory 0x4>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&rgmii1_pins &mdio_pins>;

Now use it here
	pinctrl-0 = <&rgmii1_pins &mdio_pins &phy_reset_pins>;

> +       mediatek,portmap = "l";
> +    mediatek,mdio-mode = <1>;
> +   
> +       port at 5 {
> +               status = "okay";
> +               mediatek,fixed-link = <1000 1 1 1>;
> +               phy-mode = "rgmii";

And why not use something like
	phy-reset-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
here and make sure it's taken care of, because this is imho where it
would belong.

> +       };
> +
> +       mdio-bus {
> +               status = "okay";
> +
> +               phy0: ethernet-phy at 0 {
> +                       status ="disabled";
> +                       reg = <0>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy1: ethernet-phy at 1 {
> +                       status = "disabled";
> +                       reg = <1>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy2: ethernet-phy at 2 {
> +                       status = "disabled";
> +                       reg = <2>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy3: ethernet-phy at 3 {
> +                       status = "disabled";
> +                       reg = <3>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy4: ethernet-phy at 4 {
> +                       status = "disabled";
> +                       reg = <4>;
> +                       phy-mode = "rgmii";
> +               };
> +       };
> +};
> +
> +
> +&gsw {
> +       mediatek,port5 = "gmac";
> +       mediatek,rtl8211e-reset = "yes";
No need to add a new property specific for that switch. There are
existing generic types for that.

> +};
> +
> +
> +&wmac {
> +       ralink,mtd-eeprom = <&factory 0>;
> +};
> +
> +&pcie {
> +       status = "okay";
> +};
> +
> +&pcie0 {
> +       wifi at 0,0 {
> +               reg = <0x0000 0 0 0 0>;
> +               mediatek,mtd-eeprom = <&factory 0x8000>;
> +               mediatek,2ghz = <0>;
> +       };
> +};
> diff --git a/target/linux/ramips/dts/EW-7478AC.dts
> b/target/linux/ramips/dts/EW-7478AC.dts
> new file mode 100644
> index 0000000000..ab1b284280
> --- /dev/null
> +++ b/target/linux/ramips/dts/EW-7478AC.dts
> @@ -0,0 +1,241 @@
> +/*
> + * Device Tree file for the Edimax EW-7478AC
> + * based on Edimax BR-6478AC V2
> + *
> + * Copyright (C) 2016 Rohan Murch <rohan.murch at gmail.com>
> + * Copyright (C) 2016 Hans Ulli Kroll <ulli.kroll at googlemail.com>
> + * Copyright (C) 2017 James McKenzie <openwrt at madingley.org>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2.  This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> +
> + The following definitions were found in the orignal GPL firmware source
> + HW_LED_WIRELESS_ABAND_="71"
> + HW_LED_WIRELESS_GBAND_="70"
> + HW_LED_WIRELES_="69"
> + HW_LED_POWER_="67"
> + HW_LED_WPS_="68"
> + HW_LED_LAN_="66"
> + HW_BUTTON_APSWITCH_BUT_1_="62"
> + HW_BUTTON_APSWITCH_BUT_2_="63"
> + HW_BUTTON_RESET_="60"
> +
> + The device does not have a reset button (but there are solder pads for
> a button), WPS and reset are swapped.
> +
> + */
> +
> +/dts-v1/;
> +
> +#include "mt7620a.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +       compatible = "edimax,ew-7478ac", "ralink,mt7620a-soc";
> +       model = "Edimax EW-7478ac";
> +
> +       aliases {
> +               led-boot = &led_power;
> +               led-failsafe = &led_power;
> +               led-running = &led_power;
> +               led-upgrade = &led_power;
> +       };
> +
> +       chosen {
> +               bootargs = "console=ttyS0,57600";
> +       };
> +
> +
> +       keys {
> +                compatible = "gpio-keys";
> +
> +                reset_wps {
> +                        label = "reset_wps";
> +                        gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
> +                        linux,code = <KEY_RESTART>;
> +                };
> +
> +               switch_high {
> +                       label = "switch high";
> +                       gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
> +                       linux,code = <BTN_0>;
> +                       linux,input-type = <EV_SW>;
> +               };
> +
> +               switch_off {
> +                       label = "switch off";
> +                       gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
> +                       linux,code = <BTN_1>;
> +                       linux,input-type = <EV_SW>;
> +               };
> +       };
> +
> +       leds {
> +               compatible = "gpio-leds";
> +
> +               led_power: power {
> +                       label = "ew-7478ac:green:power";
> +                       gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
> +               };
> +               lan {
> +                       label = "ew-7478ac:green:lan";
> +                       gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
> +               };
> +               wlan2g {
> +                       label = "ew-7478ac:blue:wlan2g";
> +                       gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
> +                       linux,default-trigger = "phy1radio";
> +               };
> +               wlan5g {
> +                       label = "ew-7478ac:blue:wlan5g";
> +                       gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
> +                       linux,default-trigger = "phy0radio";
> +               };
> +               wps {
> +                       label = "ew-7478ac:green:wps";
> +                       gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
> +               };
> +
> +               crossband {
> +                       label = "ew-7478ac:green:crossband";
> +                       gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
> +               };
> +       };
> +};
> +
> +
> +&gpio2 {
> +       status = "okay";
> +};
> +
> +&spi0 {
> +       status = "okay";
> +
> +       flash at 0 {
> +               compatible = "jedec,spi-nor";
> +               reg = <0 0>;
> +               spi-max-frequency = <10000000>;
> +
> +               partitions {
> +                       compatible = "fixed-partitions";
> +                       #address-cells = <1>;
> +                       #size-cells = <1>;
> +
> +                       partition at 0 {
> +                               label = "u-boot";
> +                               reg = <0x0 0x30000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 30000 {
> +                               label = "u-boot-env";
> +                               reg = <0x30000 0x10000>;
> +                               read-only;
> +                       };
> +
> +                       factory: partition at 40000 {
> +                               label = "factory";
> +                               reg = <0x40000 0x10000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 50000 {
> +                               label = "cimage";
> +                               reg = <0x50000 0x20000>;
> +                               read-only;
> +                       };
> +
> +                       partition at 70000 {
> +                               compatible = "edimax,uimage";
> +                               label = "firmware";
> +                               reg = <0x00070000 0x00790000>;
> +                       };
> +               };
> +       };
> +};
> +
> +&pinctrl {
> +       state_default: pinctrl0 {
> +               gpio {
> +            // might need pin 39: ;
> +                       ralink,group = "i2c", "uartf", "nd_sd",
> "rgmii2", "spi refclk";
> +                       ralink,function = "gpio";
> +               };
> +       };
> +};
> +
> +
> +&ethernet {
> +
> +    status = "okay";
> +       mtd-mac-address = <&factory 0x4>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&rgmii1_pins &mdio_pins>;
> +       mediatek,portmap = "l";
> +    mediatek,mdio-mode = <1>;
> +   
> +       port at 5 {
> +               status = "okay";
> +               mediatek,fixed-link = <1000 1 1 1>;
> +               phy-mode = "rgmii";
> +       };
> +
> +       mdio-bus {
> +               status = "okay";
> +
> +               phy0: ethernet-phy at 0 {
> +                       status ="disabled";
> +                       reg = <0>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy1: ethernet-phy at 1 {
> +                       status = "disabled";
> +                       reg = <1>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy2: ethernet-phy at 2 {
> +                       status = "disabled";
> +                       reg = <2>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy3: ethernet-phy at 3 {
> +                       status = "disabled";
> +                       reg = <3>;
> +                       phy-mode = "rgmii";
> +               };
> +
> +               phy4: ethernet-phy at 4 {
> +                       status = "disabled";
> +                       reg = <4>;
> +                       phy-mode = "rgmii";
> +               };
> +       };
> +};
> +
> +
> +&gsw {
> +       mediatek,port5 = "gmac";
> +       mediatek,rtl8211e-reset = "yes";
> +};
> +
> +
> +&wmac {
> +       ralink,mtd-eeprom = <&factory 0>;
> +};
> +
> +&pcie {
> +       status = "okay";
> +};
> +
> +&pcie0 {
> +       wifi at 0,0 {
> +               reg = <0x0000 0 0 0 0>;
> +               mediatek,mtd-eeprom = <&factory 0x8000>;
> +               mediatek,2ghz = <0>;
> +       };
> +};
> diff --git
> a/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
> b/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
> index 5fc5080aaf..305ce18037 100644
> ---
> a/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
> +++
> b/target/linux/ramips/files-4.14/drivers/net/ethernet/mediatek/gsw_mt7620.c
> @@ -84,6 +84,32 @@ static int mt7620_mdio_mode(struct device_node *eth_node)
>         return ret;
>  }
>  
> +void reset_realtek_phy(void){
> +#define RALINK_GPIO_DIR        0xB0000600+0x4C
> +#define RALINK_GPIO_DATA       0xB0000600+0x48
> +#define RALINK_RESETPHY_GPIO       (39-24)
> +    u32 gpiodir;
> +    u32 piodata;
> +    u32 reset_pin= RALINK_RESETPHY_GPIO;
> +   
> +    pr_info("gsw: Resetting RTL8211e using gpio 39\n");
> +    gpiodir =  le32_to_cpu(*(volatile u32 *)(RALINK_GPIO_DIR));
> +    /*set gpio1 to output*/
> +    gpiodir |= (1<<reset_pin);
> +    *(volatile u32 *)(RALINK_GPIO_DIR) = cpu_to_le32(gpiodir);
> +
> +    piodata = le32_to_cpu(*(volatile u32 *)(RALINK_GPIO_DATA));
> +    /*set to low(0)*/
> +    piodata &= ~(1L << reset_pin);
> +    *(volatile u32 *)(RALINK_GPIO_DATA) = cpu_to_le32(piodata);
> +    /*delay 30ms*/
> +    mdelay(30);
> +    /*set to high(1)*/
> +    piodata |= (1L << reset_pin);
> +    *(volatile u32 *)(RALINK_GPIO_DATA) = cpu_to_le32(piodata);
> +}
> +
> +
>  static void mt7620_hw_init(struct mt7620_gsw *gsw, int mdio_mode)
>  {
>         u32 i;
> @@ -220,6 +246,7 @@ int mtk_gsw_init(struct fe_priv *priv)
>         struct device_node *np = priv->switch_np;
>         struct platform_device *pdev = of_find_device_by_node(np);
>         struct mt7620_gsw *gsw;
> +    const char *rtl8211e_reset = NULL;
>  
>         if (!pdev)
>                 return -ENODEV;
> @@ -231,6 +258,9 @@ int mtk_gsw_init(struct fe_priv *priv)
>         priv->soc->swpriv = gsw;
>  
>         mt7620_hw_init(gsw, mt7620_mdio_mode(priv->dev->of_node));
> +    of_property_read_string(np, "mediatek,rtl8211e-reset",
> &rtl8211e_reset);
> +    if (rtl8211e_reset && !strcmp(rtl8211e_reset, "yes"))
> +        reset_realtek_phy();
>  
>         if (gsw->irq) {
>                 request_irq(gsw->irq, gsw_interrupt_mt7620, 0,
> diff --git a/target/linux/ramips/image/mt7620.mk
> b/target/linux/ramips/image/mt7620.mk
> index cf38aa2cb1..a7b14593c2 100644
> --- a/target/linux/ramips/image/mt7620.mk
> +++ b/target/linux/ramips/image/mt7620.mk
> @@ -617,6 +617,32 @@ define Device/edimax_br-6478ac-v2
>  endef
>  TARGET_DEVICES += edimax_br-6478ac-v2
>  
> +define Device/edimax_ew-7476rpc
> +  DTS := EW-7476RPC
> +  DEVICE_TITLE := Edimax EW-7476RPC
> +  BLOCKSIZE := 4k
> +  IMAGE_SIZE := 7616k
> +  IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
> +        edimax-header -s CSYS -m RN79 -f 0x70000 -S 0x01100000 |
> pad-rootfs | \
> +        append-metadata | check-size $$$$(IMAGE_SIZE)
> +  DEVICE_PACKAGES := kmod-mt76x2 kmod-phy-realtek
> +endef
> +TARGET_DEVICES += edimax_ew-7476rpc
> +
> +
> +define Device/edimax_ew-7478ac
> +  DTS := EW-7478AC
> +  DEVICE_TITLE := Edimax EW-7478AC
> +  BLOCKSIZE := 4k
> +  IMAGE_SIZE := 7616k
> +  IMAGE/sysupgrade.bin := append-kernel | append-rootfs | \
> +        edimax-header -s CSYS -m RN70 -f 0x70000 -S 0x01100000 |
> pad-rootfs | \
> +        append-metadata | check-size $$$$(IMAGE_SIZE)
> +  DEVICE_PACKAGES := kmod-mt76x2 kmod-phy-realtek
> +endef
> +TARGET_DEVICES += edimax_ew-7478ac
> +
> +
>  define Device/tplink_c2-v1
>    $(Device/Archer)
>    DTS := ArcherC2-v1
> 
> 
> 
> 
> 
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel



More information about the openwrt-devel mailing list