[OpenWrt-Devel] Second RGMII ethernet on MT7621?
John Crispin
john at phrozen.org
Mon Apr 30 15:10:49 EDT 2018
On 30/04/18 19:08, Bjørn Mork wrote:
> Hello,
>
> I have been playing with a ZyXEL WAP6805, which appears to be an OEM
> version of the https://wikidevi.com/wiki/ZyXEL_WAP6806_(Armor_X1)
>
> This thing has an oversized mini-PCIe Quantenna module. Or that's the
> mechanical form factor. The connection between the MT7621 and the
> Quantenna QT3840BC appears to be RGMII, ref the OEM bootlog below.
> Notice how this brings up both eth2 and eth3 and add them to the br0
> bridge. The Quantenna module loads u-boot and a firmware image using
> tftp, and it is then managed over the ethernet interface.
>
> So I was looking for a quick way to enable the second ethernet port on
> the MT7621, but can't find any. Am I looking the wrong place, or am I
> right that the support for this is still lacking? Any idea how many
> bits and pieces are missing?
>
>
>
> Bjørn
Hi Bjørn
making gmac2 work s not trivial with the current driver. however making the upstream mtk_eth_soc driver work on mt7621 is pretty easy i think and will give you dual gmac support. upstream only supports mt7623 arm atm. its been on my todo list for a while but i simply have not been able to find the 2-3 days required to make it work.
John
>
>
> Linux version 2.6.36+ (max at localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #23 SMP Fri May 20 09:28:27 CST 2016
>
> The CPU feqenuce set to 880 MHz
> GCMP present
> CPU revision is: 0001992f (MIPS 1004Kc)
> Software DMA cache coherency
> Determined physical RAM map:
> memory: 04000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 0x00000000 -> 0x00004000
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0x00000000 -> 0x00004000
> avail: cpu2 is not ready
> avail: cpu3 is not ready
> Detected 1 available secondary CPU(s)
> PERCPU: Embedded 7 pages/cpu @81083000 s6464 r8192 d14016 u65536
> pcpu-alloc: s6464 r8192 d14016 u65536 alloc=16*4096
> pcpu-alloc: [0] 0 [0] 1
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
> Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS1,57600 root=/dev/ram0 rootfstype=squashfs,jffs2
> PID hash table entries: 256 (order: -2, 1024 bytes)
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> Writing ErrCtl register=00011c44
> Readback ErrCtl register=00011c44
> Memory: 51780k/65536k available (4115k kernel code, 13756k reserved, 1484k data, 7220k init, 0k highmem)
> Hierarchical RCU implementation.
> Verbose stalled-CPUs detection is disabled.
> NR_IRQS:128
> Trying to install interrupt handler for IRQ24
> Trying to install interrupt handler for IRQ25
> Trying to install interrupt handler for IRQ22
> Trying to install interrupt handler for IRQ9
> Trying to install interrupt handler for IRQ10
> Trying to install interrupt handler for IRQ11
> Trying to install interrupt handler for IRQ12
> Trying to install interrupt handler for IRQ13
> Trying to install interrupt handler for IRQ14
> Trying to install interrupt handler for IRQ16
> Trying to install interrupt handler for IRQ17
> Trying to install interrupt handler for IRQ18
> Trying to install interrupt handler for IRQ19
> Trying to install interrupt handler for IRQ20
> Trying to install interrupt handler for IRQ21
> Trying to install interrupt handler for IRQ23
> Trying to install interrupt handler for IRQ26
> Trying to install interrupt handler for IRQ27
> Trying to install interrupt handler for IRQ28
> Trying to install interrupt handler for IRQ15
> Trying to install interrupt handler for IRQ8
> Trying to install interrupt handler for IRQ29
> Trying to install interrupt handler for IRQ30
> Trying to install interrupt handler for IRQ31
> CPU0: status register was 11000000
> CPU0: status register now 11000000
> CPU0: status register frc 11001800
> console [ttyS1] enabled
> Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168)
> pid_max: default: 32768 minimum: 301
> Mount-cache hash table entries: 512
> launch: starting cpu1
> launch: cpu1 gone!
> CPU revision is: 0001992f (MIPS 1004Kc)
> Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes.
> Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
> MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
> Brought up 2 CPUs
> Synchronize counters across 2 CPUs: done.
> NET: Registered protocol family 16
> release PCIe RST: RALINK_RSTCTRL = 1000000
> PCIE PHY initialize
> ***** Xtal 40MHz *****
> start MT7621 PCIe register access
> RALINK_RSTCTRL = 1000000
> RALINK_CLKCFG1 = 77ffeff8
>
> *************** MT7621 PCIe RC mode *************
> pcie_link status = 0x1
> RALINK_RSTCTRL= 1000000
> *** Configure Device number setting of Virtual PCI-PCI bridge ***
> RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
> PCIE0 enabled
> interrupt enable status: 100000
> Port 0 N_FTS = 1b105000
> config reg done
> init_rt2880pci done
> bio: create slab <bio-0> at 0
> vgaarb: loaded
> SCSI subsystem initialized
> pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
> pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
> pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
> pci 0000:00:00.0: BAR 1: set to [mem 0x60100000-0x6010ffff] (PCI address [0x60100000-0x6010ffff]
> pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
> pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff] (PCI address [0x60000000-0x600fffff]
> pci 0000:00:00.0: PCI bridge to [bus 01-01]
> pci 0000:00:00.0: bridge window [io disabled]
> pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
> pci 0000:00:00.0: bridge window [mem pref disabled]
> PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
> BAR0 at slot 0 = 0
> bus=0x0, slot = 0x0
> res[0]->start = 0
> res[0]->end = 0
> res[1]->start = 60100000
> res[1]->end = 6010ffff
> res[2]->start = 0
> res[2]->end = 0
> res[3]->start = 0
> res[3]->end = 0
> res[4]->start = 0
> res[4]->end = 0
> res[5]->start = 0
> res[5]->end = 0
> bus=0x1, slot = 0x0, irq=0x4
> res[0]->start = 60000000
> res[0]->end = 600fffff
> res[1]->start = 0
> res[1]->end = 0
> res[2]->start = 0
> res[2]->end = 0
> res[3]->start = 0
> res[3]->end = 0
> res[4]->start = 0
> res[4]->end = 0
> res[5]->start = 0
> res[5]->end = 0
> Switching to clocksource MIPS
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 2048 (order: 2, 16384 bytes)
> TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
> TCP: Hash tables configured (established 2048 bind 2048)
> TCP reno registered
> UDP hash table entries: 128 (order: 0, 4096 bytes)
> UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
> NET: Registered protocol family 1
> 4 CPUs re-calibrate udelay(lpj = 1167360)
> msgmni has been set to 101
> Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
> io scheduler noop registered (default)
> Ralink gpio driver initialized
> spidrv_major = 217
> Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
> serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
> serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
> brd: module loaded
> MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
> Allocate 16 byte aligned buffer: 80cb7860
> Enable NFI Clock
> # MTK NAND # : Use HW ECC
> NAND ID [01 F1 80 1D 01, 00801d01]
> Device found in MTK table, ID: 1f1, EXT_ID: 801d01
> Support this Device in MTK table! 1f1
> NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
> [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
> Scanning device for bad blocks
> Creating 10 MTD partitions on "MT7621-NAND":
> 0x000000000000-0x000008000000 : "ALL"
> 0x000000000000-0x000000100000 : "Bootloader"
> 0x000000100000-0x000000200000 : "MRD"
> 0x000000200000-0x000000300000 : "Factory"
> 0x000000300000-0x000000400000 : "Config"
> 0x000000400000-0x000002400000 : "Kernel"
> 0x000002400000-0x000004400000 : "Kernel2"
> 0x000004400000-0x000004500000 : "Private"
> 0x000004500000-0x000005500000 : "Log"
> 0x000005500000-0x000008000000 : "App"
> [mtk_nand] probe successfully!
> Signature matched and data read!
> load_fact_bbt success 1023
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> rdm_major = 253
> GMAC1_MAC_ADRH -- : 0x00006031
> GMAC1_MAC_ADRL -- : 0x97661610
> Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500!
> GMAC1_MAC_ADRH -- : 0x00006031
> GMAC1_MAC_ADRL -- : 0x97661610
> PROC INIT OK!
> register mt_drv
>
>
> === pAd = c0282000, size = 813160 ===
>
> <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
> <-- RTMPAllocAdapterBlock, Status=0
> pAd->CSRBaseAddress =0xc0180000, csr_addr=0xc0180000!
> device_id =0x7603
> RtmpChipOpsHook(507): Not support for HIF_MT yet!
> mt7603_init()-->
> mt_bcn_buf_init(224): Not support for HIF_MT yet!
> <--mt7603_init()
> nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
> GRE over IPv4 demultiplexor driver
> ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
> TCP cubic registered
> NET: Registered protocol family 10
> IPv6 over IPv4 tunneling driver
> NET: Registered protocol family 17
> L2TP core driver, V2.0
> 802.1Q VLAN Support v1.8 Ben Greear <greearb at candelatech.com>
> All bugs added by David S. Miller <davem at redhat.com>
> Freeing unused kernel memory: 7220k freed
> init started: BusAlgorithmics/MIPS FPU Emulator v1.5
> yBox v1.12.1 (2016-05-18 18devpts: called with bogus options
> :16:53 CST)
> starting pid 33, tty '': '/etc_ro/rcS'
> mount: mounting none onralink_gpio: irq number(8) pid =38
> /ralink_gpio: irq number(1001) pid =38
> pralink_gpio: irq number(1001) pid =38
> ralink_gpio: irq number(18) pid =37
> roc/bus/usb failed: No such file or directory
> Welcome to
> _______ _______ ___ __ ____ _ _ ___
> | ___ \| __ || | |__|| \ | || | / /
> | |___|
> login as: TX_BCN DESC a25ab000 size = 320
> RX[0] DESC a25af000 size = 2048
> RX[1] DESC a25b2000 size = 2048
> E2pAccessMode=2
> cfg_mode=9
> cfg_mode=9
> wmode_band_equal(): Band Equal!
> APSDCapable[0]=0
> APSDCapable[1]=0
> APSDCapable[2]=0
> APSDCapable[3]=0
> APSDCapable[4]=0
> APSDCapable[5]=0
> APSDCapable[6]=0
> APSDCapable[7]=0
> APSDCapable[8]=0
> APSDCapable[9]=0
> APSDCapable[10]=0
> APSDCapable[11]=0
> APSDCapable[12]=0
> APSDCapable[13]=0
> APSDCapable[14]=0
> APSDCapable[15]=0
> FW Version:_mt7603mp
> FW Build Date:20150624233050
> CmdAddressLenReq:(ret = 0)
> CmdFwStartReq: override = 1, address = 1048576
> CmdStartDLRsp: WiFI FW Download Success
> AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
> efuse_probe: efuse = 10000012
> RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
> RtmpEepromGetDefault::e2p_dafault=1
> RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
> NVM is FLASH mode, flash_offset = 0x40000
> 1. Phy Mode = 14
> Country Region from e2p = ffff
> tssi_1_target_pwr_g_band = 34
> 2. Phy Mode = 14
> 3. Phy Mode = 14
> NICInitPwrPinCfg(14): Not support for HIF_MT yet!
> NICInitializeAsic(584): Not support rtmp_mac_sys_reset () for HIF_MT yet!
> mt_mac_init()-->
> mt7603_init_mac_cr()-->
> AsicSetMacMaxLen(1859): Set the Max RxPktLen=1024!
> <--mt_mac_init()
> WTBL Segment 1 info:
> MemBaseAddr/FID:0x28000/0
> EntrySize/Cnt:32/128
> WTBL Segment 2 info:
> MemBaseAddr/FID:0x40000/0
> EntrySize/Cnt:64/128
> WTBL Segment 3 info:
> MemBaseAddr/FID:0x42000/64
> EntrySize/Cnt:64/128
> WTBL Segment 4 info:
> MemBaseAddr/FID:0x44000/128
> EntrySize/Cnt:32/128
> MtAsicACQueue: Write CR:21510, Value=10421
> MtAsicACQueue: Write CR:21500, Value=10421
> AntCfgInit(2538): Not support for HIF_MT yet!
> RTMPSetPhyMode(): channel out of range, use first ch=0
> MCS Set = ff ff 00 00 01
> mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#12(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#13(2T2R), BBP_BW=0
> mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0
> SYNC - BBP R4 to 20MHz.l
> [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=4, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=5, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=6, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> [PMF]ap_pmf_init:: apidx=7, MFPC=0, MFPR=0, SHA256=0
> [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
> AsicSetRalinkBurstMode(4185): Not support for HIF_MT yet!
> RTMPSetPiggyBack(921): Not support for HIF_MT yet!
> mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1
> AsicSetTxPreamble(4172): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicAddSharedKeyEntry(2025): Not support for HIF_MT yet!
> AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0
> Main bssid = 62:31:87:66:16:10
> <==== rt28xx_init, Status=0
> @@@ ed_monitor_init : ===>
> @@@ ed_monitor_init : <===
> WiFi Startup Cost (ra0): 7.180s
> Raeth v3.1 (Tasklet)
> free_head_phy is 0xae2000!!!
> free_tail_phy is 0xae3ff0!!!
> txd_pool=a0ae4000 phy_txd_pool=00AE4000
> ei_local->skb_free start address is 0x83ccd48c.
> free_txd: a0ae4010, ei_local->cpu_ptr: 00AE4000
> POOL HEAD_PTR | DMA_PTR | CPU_PTR
> ----------------+---------+--------
> 0xa0ae4000 0x00AE4000 0x00AE4000
>
> phy_rx_ring0 = 0x00ae6000, rx_ring0 = 0xa0ae6000
>
> phy_rx_ring0 = 0x00aea000, rx_ring0 = 0xa0aea000
> change HW-TRAP to 0x17ccf!!!!!!!!!!!!GMAC1_MAC_ADRH -- : 0x00006031
> GMAC1_MAC_ADRL -- : 0x97661610
> GDMA2_MAC_ADRH -- : 0x0000000c
> GDMA2_MAC_ADRL -- : 0x432880d3
> eth3: ===> VirtualIF_open
> CDMA_CSG_CFG = 81000000
> GDMA1_FWD_CFG = 20710000
> GDMA2_FWD_CFG = 20710000
> VID MAC
> 5 000000000000
> 9 000000000000
> 10 000000000000
> 11 000000000000
> device ra0 entered promiscuous mode
> device eth2 entered promiscuous mode
> br0: port 2(eth2) entering learning state
> br0: port 2(eth2) entering learning state
> br0: port 1(ra0) entering learning state
> br0: port 1(ra0) entering learning state
> br0: port 2(eth2) entering learning state
> br0: port 1(ra0) entering learning state
> br0: port 2(eth2) entering learning state
> br0: port 2(eth2) entering learning state
> br0: port 1(ra0) entering learning state
> br0: port 1(ra0) entering learning state
> set mcastVlan to 0 in ethernet driver
> ADDRCONF(NETDEV_UP): sit0: link is not ready
> ADDRCONF(NETDEV_UP): ip6tnl0: link is not ready
> ADDRCONF(NETDEV_UP): ra1: link is not ready
> ADDRCONF(NETDEV_UP): ra2: link is not ready
> ADDRCONF(NETDEV_UP): ra3: link is not ready
> ADDRCONF(NETDEV_UP): ra4: link is not ready
> ADDRCONF(NETDEV_UP): ra5: link is not ready
> ADDRCONF(NETDEV_UP): ra6: link is not ready
> ADDRCONF(NETDEV_UP): ra7: link is not ready
> ADDRCONF(NETDEV_UP): eth3: link is not ready
> switch register base addr to 0xbe110000
> write offset 0x8, value 0x9000c
> eth3: ===> VirtualIF_open
> device eth3 entered promiscuous mode
> br0: port 3(eth3) entering learning state
> br0: port 3(eth3) entering learning state
> killall rt2860apd 1>/dev/null 2>&1 1>/dev/null 2>&1
> br0: port 2(eth2) entering forwarding state
> br0: port 1(ra0) entering forwarding state
> dropbear.sh 1>/dev/null 2>&1
> ralink_gpio: irq number(999) pid =1241
> ralink_gpio: irq number(999) pid =1241
> br0: port 3(eth3) entering forwarding state
> killall -q udpsvd 1>/dev/null 2>&1
> udpsvd -Ev 0 69 tftpd& 1>/dev/null 2>&1
> ntp.sh 1>/dev/null 2>&1
> rm -rf /var/run/wscd.pid.ra0 1>/dev/null 2>&1
> iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
> iwpriv ra0 set WscConfMode=7 1>/dev/null 2>&1
> iwpriv ra0 set WscConfStatus=1 1>/dev/null 2>&1
> route add -host 239.255.255.250 dev br0 1>/dev/null 2>&1
> wscd -m 1 -a 169.254.71.254 -i ra0 -D 1>/dev/null 2>&1
> killall -q klogd 1>/dev/null 2>&1
> killall -q syslogd 1>/dev/null 2>&1
> syslogd -C8 1>/dev/null 2>&1 1>/dev/null 2>&1
> klogd 1>/dev/null 2>&1 1>/dev/null 2>&1
> killall -q mini_httpd 1>/dev/null 2>&1
> mkdir -p /var/web 1>/dev/null 2>&1
> cp -r /etc_ro/web/* /var/web 1>/dev/null 2>&1
> mini_httpd -p 80 -C /etc_ro/mini_httpd_debug.conf 1>/dev/null 2>&1
> wpsState=3 monitorInterface=-1 wpsEnd=0
> 6: slow blinking Green (2 sec), Amber (0,25 sec)
>
> login as:
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel at lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list