[OpenWrt-Devel] [PATCH 1/2] ipq806x: Add support for Netgear R7500v2

Alexis Green agreen at cococorp.com
Wed Mar 23 15:55:09 EDT 2016


---
 .../linux/ipq806x/base-files/etc/board.d/01_leds   |  19 +-
 .../ipq806x/base-files/etc/board.d/02_network      |   3 +-
 .../etc/hotplug.d/firmware/11-ath10k-caldata       |  50 +++
 target/linux/ipq806x/base-files/lib/ipq806x.sh     |   3 +
 .../ipq806x/base-files/lib/upgrade/platform.sh     |   6 +-
 target/linux/ipq806x/image/Makefile                |  14 +-
 ...-Netgear-Nighthawk-X4-D7500v2-device-tree.patch | 363 +++++++++++++++++++++
 target/linux/ipq806x/profiles/netgear.mk           |  13 +
 8 files changed, 460 insertions(+), 11 deletions(-)
 create mode 100755 target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
 create mode 100644 target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch

diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index b32c1cc..2e86118 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -10,15 +10,20 @@ board_config_update
 
 board=$(ipq806x_board_name)
 
+netgear_leds() {
+	ucidef_set_led_usbdev "usb1" "USB 1" "${board}:white:usb1" "1-1"
+	ucidef_set_led_usbdev "usb2" "USB 2" "${board}:white:usb3" "3-1"
+	ucidef_set_led_netdev "wan" "WAN" "${board}:white:wan" "eth0"
+	ucidef_set_led_ide "esata" "eSATA" "${board}:amber:esata"
+	ucidef_set_led_default "wps" "WPS" "${board}:white:wps" "0"
+	ucidef_set_led_default "rfkill" "rfkill" "${board}:white:rfkill" "0"
+}
+
 case "$board" in
 d7800 |\
-r7500)
-	ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1"
-	ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1"
-	ucidef_set_led_netdev "wan" "WAN" "r7500:white:wan" "eth0"
-	ucidef_set_led_ide "esata" "eSATA" "r7500:amber:esata"
-	ucidef_set_led_default "wps" "WPS" "r7500:white:wps" "0"
-	ucidef_set_led_default "rfkill" "rfkill" "r7500:white:rfkill" "0"
+r7500 |\
+r7500v2)
+	netgear_leds
 	;;
 *)
 	;;
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 6e18297..0ee6b3e 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -14,7 +14,8 @@ board=$(ipq806x_board_name)
 case "$board" in
 ap148 |\
 d7800 |\
-r7500)
+r7500 |\
+r7500v2)
 	ucidef_add_switch "switch0" \
 		"1:lan" "2:lan" "3:lan" "4:lan" "6 at eth1" "5:wan" "0 at eth0"
 	;;
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
new file mode 100755
index 0000000..0f5b32c
--- /dev/null
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -0,0 +1,50 @@
+#!/bin/sh
+
+ath10kcal_die() {
+	echo "ath10cal: " "$*"
+	exit 1
+}
+
+ath10kcal_extract() {
+	local part=$1
+	local offset=$2
+	local count=$3
+	local mtd
+
+	mtd=$(find_mtd_chardev $part)
+	[ -n "$mtd" ] || \
+		ath10kcal_die "no mtd device found for partition $part"
+
+	dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
+		ath10kcal_die "failed to extract calibration data from $mtd"
+}
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/ipq806x.sh
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(ipq806x_board_name)
+
+case "$FIRMWARE" in
+"ath10k/cal-pci-0000:01:00.0.bin")
+	case $board in
+	d7800 |\
+	r7500v2 )
+		ath10kcal_extract "art" 4096 12064
+		;;
+	esac
+	;;
+"ath10k/cal-pci-0001:01:00.0.bin")
+	case $board in
+	d7800 |\
+	r7500v2 )
+		ath10kcal_extract "art" 20480 12064
+		;;
+	esac
+	;;
+*)
+	exit 1
+	;;
+esac
diff --git a/target/linux/ipq806x/base-files/lib/ipq806x.sh b/target/linux/ipq806x/base-files/lib/ipq806x.sh
index db22708..68cffd5 100644
--- a/target/linux/ipq806x/base-files/lib/ipq806x.sh
+++ b/target/linux/ipq806x/base-files/lib/ipq806x.sh
@@ -26,6 +26,9 @@ ipq806x_board_detect() {
 	*"R7500")
 		name="r7500"
 		;;
+	*"R7500v2")
+		name="r7500v2"
+		;;
 	esac
 
 	[ -z "$name" ] && name="unknown"
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 542b5ce..1acdfe4 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -8,7 +8,8 @@ platform_check_image() {
 	case "$board" in
 	ap148 |\
 	d7800 |\
-	r7500)
+	r7500 |\
+	r7500v2)
 		nand_do_platform_check $board $1
 		return $?;
 		;;
@@ -23,7 +24,8 @@ platform_pre_upgrade() {
 	case "$board" in
 	ap148 |\
 	d7800 |\
-	r7500)
+	r7500 |\
+	r7500v2)
 		nand_do_upgrade "$1"
 		;;
 	esac
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index ff8b2c7..4040955 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -133,6 +133,18 @@ define Device/R7500
 	BOARD_NAME := r7500
 endef
 
-TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500
+define Device/R7500v2
+	$(call Device/DniImage)
+	DEVICE_DTS := qcom-ipq8064-r7500v2
+	KERNEL_SIZE := 2097152
+	NETGEAR_BOARD_ID := R7500v2
+	NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
+	BLOCKSIZE := 128KiB
+	PAGESIZE := 2048
+	BOARD_NAME := r7500v2
+endef
+
+
+TARGET_DEVICES += AP148 AP148-legacy D7800 DB149 R7500 R7500v2
 
 $(eval $(call BuildImage))
diff --git a/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch b/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch
new file mode 100644
index 0000000..5eff49a
--- /dev/null
+++ b/target/linux/ipq806x/patches-3.18/802-ARM-qcom-add-Netgear-Nighthawk-X4-D7500v2-device-tree.patch
@@ -0,0 +1,363 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+ 	qcom-ipq8064-ap148.dtb \
+ 	qcom-ipq8064-db149.dtb \
+ 	qcom-ipq8064-r7500.dtb \
++	qcom-ipq8064-r7500v2.dtb \
+ 	qcom-ipq8064-d7800.dtb \
+ 	qcom-msm8660-surf.dtb \
+ 	qcom-msm8960-cdp.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/qcom-ipq8064-r7500v2.dts
+@@ -0,0 +1,350 @@
++#include "qcom-ipq8064-v1.0.dtsi"
++
++#include <dt-bindings/input/input.h>
++
++/ {
++	model = "Netgear Nighthawk X4 R7500v2";
++	compatible = "netgear,r7500v2", "qcom,ipq8064";
++
++	memory at 0 {
++		reg = <0x42000000 0xe000000>;
++		device_type = "memory";
++	};
++
++	reserved-memory {
++		#address-cells = <1>;
++		#size-cells = <1>;
++		ranges;
++		rsvd at 41200000 {
++			reg = <0x41200000 0x300000>;
++			no-map;
++		};
++	};
++
++	aliases {
++		serial0 = &uart4;
++		mdio-gpio0 = &mdio0;
++	};
++
++	chosen {
++		bootargs = "rootfstype=squashfs noinitrd";
++		linux,stdout-path = "serial0:115200n8";
++	};
++
++	soc {
++		pinmux at 800000 {
++			i2c4_pins: i2c4_pinmux {
++				pins = "gpio12", "gpio13";
++				function = "gsbi4";
++				bias-disable;
++			};
++
++			nand_pins: nand_pins {
++				mux {
++					pins = "gpio34", "gpio35", "gpio36",
++					       "gpio37", "gpio38", "gpio39",
++					       "gpio40", "gpio41", "gpio42",
++					       "gpio43", "gpio44", "gpio45",
++					       "gpio46", "gpio47";
++					function = "nand";
++					drive-strength = <10>;
++					bias-disable;
++				};
++				pullups {
++					pins = "gpio39";
++					bias-pull-up;
++				};
++				hold {
++					pins = "gpio40", "gpio41", "gpio42",
++					       "gpio43", "gpio44", "gpio45",
++					       "gpio46", "gpio47";
++					bias-bus-hold;
++				};
++			};
++
++			mdio0_pins: mdio0_pins {
++				mux {
++					pins = "gpio0", "gpio1";
++					function = "gpio";
++					drive-strength = <8>;
++					bias-disable;
++				};
++			};
++
++			rgmii2_pins: rgmii2_pins {
++				mux {
++					pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
++					       "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
++					function = "rgmii2";
++					drive-strength = <8>;
++					bias-disable;
++				};
++			};
++		};
++
++		gsbi at 16300000 {
++			qcom,mode = <GSBI_PROT_I2C_UART>;
++			status = "ok";
++			serial at 16340000 {
++				status = "ok";
++			};
++			/*
++			 * The i2c device on gsbi4 should not be enabled.
++			 * On ipq806x designs gsbi4 i2c is meant for exclusive
++			 * RPM usage. Turning this on in kernel manifests as
++			 * i2c failure for the RPM.
++			 */
++		};
++
++		sata-phy at 1b400000 {
++			status = "ok";
++		};
++
++		sata at 29000000 {
++			status = "ok";
++		};
++
++		phy at 100f8800 {		/* USB3 port 1 HS phy */
++			status = "ok";
++		};
++
++		phy at 100f8830 {		/* USB3 port 1 SS phy */
++			status = "ok";
++		};
++
++		phy at 110f8800 {		/* USB3 port 0 HS phy */
++			status = "ok";
++		};
++
++		phy at 110f8830 {		/* USB3 port 0 SS phy */
++			status = "ok";
++		};
++
++		usb30 at 0 {
++			status = "ok";
++		};
++
++		usb30 at 1 {
++			status = "ok";
++		};
++
++		pcie0: pci at 1b500000 {
++			status = "ok";
++			reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
++			pinctrl-0 = <&pcie0_pins>;
++			pinctrl-names = "default";
++		};
++
++		pcie1: pci at 1b700000 {
++			status = "ok";
++			reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
++			pinctrl-0 = <&pcie1_pins>;
++			pinctrl-names = "default";
++		};
++
++		nand at 1ac00000 {
++			status = "ok";
++
++			pinctrl-0 = <&nand_pins>;
++			pinctrl-names = "default";
++
++			nand-ecc-strength = <4>;
++			nand-bus-width = <8>;
++
++			#address-cells = <1>;
++			#size-cells = <1>;
++
++			qcadata at 0 {
++				label = "qcadata";
++				reg = <0x0000000 0x0c80000>;
++				read-only;
++			};
++
++			APPSBL at c80000 {
++				label = "APPSBL";
++				reg = <0x0c80000 0x0500000>;
++				read-only;
++			};
++
++			APPSBLENV at 1180000 {
++				label = "APPSBLENV";
++				reg = <0x1180000 0x0080000>;
++				read-only;
++			};
++
++			art: art at 1200000 {
++				label = "art";
++				reg = <0x1200000 0x0140000>;
++				read-only;
++			};
++
++			artbak: art at 1340000 {
++				label = "artbak";
++				reg = <0x1340000 0x0140000>;
++				read-only;
++			};
++
++			kernel at 1480000 {
++				label = "kernel";
++				reg = <0x1480000 0x0200000>;
++			};
++
++			ubi at 1680000 {
++				label = "ubi";
++				reg = <0x1680000 0x1E00000>;
++			};
++
++			netgear at 3480000 {
++				label = "netgear";
++				reg = <0x3480000 0x4480000>;
++				read-only;
++			};
++
++			reserve at 7900000 {
++				label = "reserve";
++				reg = <0x7900000 0x0700000>;
++				read-only;
++			};
++
++			firmware at 1480000 {
++				label = "firmware";
++				reg = <0x1480000 0x2000000>;
++			};
++
++		};
++
++		mdio0: mdio {
++			compatible = "virtual,mdio-gpio";
++			#address-cells = <1>;
++			#size-cells = <0>;
++			gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
++			pinctrl-0 = <&mdio0_pins>;
++			pinctrl-names = "default";
++
++			phy0: ethernet-phy at 0 {
++				device_type = "ethernet-phy";
++				reg = <0>;
++				qca,ar8327-initvals = <
++					0x00004 0x7600000   /* PAD0_MODE */
++					0x00008 0x1000000   /* PAD5_MODE */
++					0x0000c 0x80        /* PAD6_MODE */
++					0x000e4 0xaa545     /* MAC_POWER_SEL */
++					0x000e0 0xc74164de  /* SGMII_CTRL */
++					0x0007c 0x4e        /* PORT0_STATUS */
++					0x00094 0x4e        /* PORT6_STATUS */
++					>;
++			};
++
++			phy4: ethernet-phy at 4 {
++				device_type = "ethernet-phy";
++				reg = <4>;
++			};
++		};
++
++		gmac1: ethernet at 37200000 {
++			status = "ok";
++			phy-mode = "rgmii";
++			qcom,id = <1>;
++
++			pinctrl-0 = <&rgmii2_pins>;
++			pinctrl-names = "default";
++
++			mtd-mac-address = <&art 6>;
++
++			fixed-link {
++				speed = <1000>;
++				full-duplex;
++			};
++		};
++
++		gmac2: ethernet at 37400000 {
++			status = "ok";
++			phy-mode = "sgmii";
++			qcom,id = <2>;
++
++			mtd-mac-address = <&art 0>;
++
++			fixed-link {
++				speed = <1000>;
++				full-duplex;
++			};
++		};
++	};
++
++	gpio-keys {
++		compatible = "gpio-keys";
++
++		wifi {
++			label = "wifi";
++			gpios = <&qcom_pinmux 6 1>;
++			linux,code = <KEY_WLAN>;
++		};
++
++		reset {
++			label = "reset";
++			gpios = <&qcom_pinmux 54 1>;
++			linux,code = <KEY_RESTART>;
++		};
++
++		wps {
++			label = "wps";
++			gpios = <&qcom_pinmux 65 1>;
++			linux,code = <KEY_WPS_BUTTON>;
++		};
++	};
++
++	gpio-leds {
++		compatible = "gpio-leds";
++
++		usb1 {
++			label = "r7500v2:amber:usb1";
++			gpios = <&qcom_pinmux 7 0>;
++		};
++
++		usb3 {
++			label = "r7500v2:amber:usb3";
++			gpios = <&qcom_pinmux 8 0>;
++		};
++
++		status {
++			label = "r7500v2:amber:status";
++			gpios = <&qcom_pinmux 9 0>;
++		};
++
++		internet {
++			label = "r7500v2:white:internet";
++			gpios = <&qcom_pinmux 22 0>;
++		};
++
++		wan {
++			label = "r7500v2:white:wan";
++			gpios = <&qcom_pinmux 23 0>;
++		};
++
++		wps {
++			label = "r7500v2:white:wps";
++			gpios = <&qcom_pinmux 24 0>;
++		};
++
++		esata {
++			label = "r7500v2:white:esata";
++			gpios = <&qcom_pinmux 26 0>;
++		};
++
++		power {
++			label = "r7500v2:white:power";
++			gpios = <&qcom_pinmux 53 0>;
++			default-state = "on";
++		};
++
++		rfkill {
++			label = "r7500v2:white:rfkill";
++			gpios = <&qcom_pinmux 64 0>;
++		};
++
++	};
++};
++
++&adm_dma {
++	status = "ok";
++};
diff --git a/target/linux/ipq806x/profiles/netgear.mk b/target/linux/ipq806x/profiles/netgear.mk
index 25258cd..e64831b 100644
--- a/target/linux/ipq806x/profiles/netgear.mk
+++ b/target/linux/ipq806x/profiles/netgear.mk
@@ -29,5 +29,18 @@ endef
 define Profile/R7500/Description
 	Package set for the Netgear Nighthawk X4 R7500.
 endef
+
+define Profile/R7500v2
+	NAME:=Netgear Nighthawk X4 R7500v2
+	PACKAGES:= \
+		kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \
+		kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \
+		kmod-ath10k wpad-mini ath10k-firmware-qca99x0
+endef
+
+define Profile/R7500v2/Description
+	Package set for the Netgear Nighthawk X4 R7500v2.
+endef
 $(eval $(call Profile,D7800))
 $(eval $(call Profile,R7500))
+$(eval $(call Profile,R7500v2))
-- 
2.1.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list