[OpenWrt-Devel] [PATCH 5/5] ar71xx: Use PHY fixups for Open Mesh MR1750

Sven Eckelmann sven.eckelmann at open-mesh.com
Tue Mar 8 12:39:07 EST 2016


From: Sven Eckelmann <sven.eckelmann at open-mesh.com>

The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann at open-mesh.com>
---
 .../ar71xx/files/arch/mips/ath79/mach-mr1750.c     | 25 +++++++++++++++++++---
 1 file changed, 22 insertions(+), 3 deletions(-)

diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-mr1750.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-mr1750.c
index 8db2915..83acd4c 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/mach-mr1750.c
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-mr1750.c
@@ -22,6 +22,7 @@
 #include <linux/ar8216_platform.h>
 
 #include <asm/mach-ath79/ar71xx_regs.h>
+#include <linux/platform_data/phy-at803x.h>
 
 #include "common.h"
 #include "dev-ap9x-pci.h"
@@ -92,14 +93,29 @@ static struct gpio_keys_button mr1750_gpio_keys[] __initdata = {
 	},
 };
 
+static struct at803x_platform_data mr1750_at803x_data = {
+	.disable_smarteee = 1,
+	.enable_rgmii_rx_delay = 1,
+	.enable_rgmii_tx_delay = 0,
+	.fixup_rgmii_tx_delay = 1,
+};
+
+static struct mdio_board_info mr1750_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 5,
+		.platform_data = &mr1750_at803x_data,
+	},
+};
+
 static void __init mr1750_setup(void)
 {
 	u8 *art = (u8 *)KSEG1ADDR(0x1fff0000);
 	u8 mac[6];
 
-	ath79_eth0_pll_data.pll_1000 = 0xbe000101;
-	ath79_eth0_pll_data.pll_100 = 0x80000101;
-	ath79_eth0_pll_data.pll_10 = 0x80001313;
+	ath79_eth0_pll_data.pll_1000 = 0xae000000;
+	ath79_eth0_pll_data.pll_100 = 0xa0000101;
+	ath79_eth0_pll_data.pll_10 = 0xa0001313;
 
 	ath79_register_m25p80(NULL);
 
@@ -116,6 +132,9 @@ static void __init mr1750_setup(void)
 	ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN, 3, 3, 0, 0);
 	ath79_register_mdio(0, 0x0);
 
+	mdiobus_register_board_info(mr1750_mdio0_info,
+				    ARRAY_SIZE(mr1750_mdio0_info));
+
 	ath79_init_mac(ath79_eth0_data.mac_addr, art + MR1750_MAC0_OFFSET, 0);
 
 	/* GMAC0 is connected to the RMGII interface */
-- 
2.7.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel


More information about the openwrt-devel mailing list